Influence of alloy components on arc erosion morphology of Ag/MeO electrical contact materials

Arc erosion morphologies of Ag/MeO（10） electrical contact materials after 50000 operations under direct current of 19 V and 20 A and resistive load conditions were investigated using scanning electron microscope（SEM） and a 3D optical profiler（3DOP）. The results indicated that 3DOP could supply clearer and more detailed arc erosion morphology information. Arc erosion resistance of Ag/SnO_2（10） electrical contact material was the best and that of Ag/CuO（10） was the worst. Arc erosion morphology of Ag/MeO（10） electrical contact materials mainly included three different types. Arc erosion morphologies of Ag/ZnO（10） and Ag/SnO_2（10） electrical contact materials were mainly liquid splash and evaporation, and those of Ag/CuO（10） and Ag/CdO（10） were mainly material transfer from anode to cathode. Arc erosion morphology of Ag/SnO_2（6）In_2O_3（4） electrical contact materials included both liquid splash, evaporation and material transfer. In addition, the formation process and mechanism on arc erosion morphology of Ag/MeO（10） electrical contact materials were discussed.

DIFFERENTIAL SCANNING CALORIMETRY AND X-RAY DIFFRACTION STUDIES ON AGING BEHAVIOR OF Zn-Al ALLOYS

Decomposition processes of the quenched Zn-Al alloys were studied by differential scanning calorimetry (DSC), X-ray diffraction (XRD) and transmission electron microscopy (TEM). The results show that the stabilities of supersaturated solid solution (SSS) of Zn-Al alloy and α' phase formed by quenching would reduce with the increase of Zn content and the precipitation of η-Zn phases even when aging at ambient temperature, so that the exothermic precipitation peak in DSC curve would disappear. The activation energy of the η-Zn precipitation and the reaction enthalpy were calculated and measured. The kinetics of α' decomposition or η-Zn formation was determined by XRD. The microstructure change during aging was observed by TEM.

Influence of operation number on arc erosion behavior of Ag/Ni electrical contact materials

Arc erosion behavior of Ag/Ni materials with different operation numbers was investigated by OM,3DOP and SEM.The results indicated that the arc erosion of Ag/10Ni electrical contact material fabricated by sintering−extrusion technology was more and more serious with the operation numbers increasing from 1000 to 40000.With the same operation numbers,the arc erosion on anode was more serious than that on cathode.Besides,the pores preferred to emerge around the arc effect spot during the first 10000 operations.And the morphology of the molten silver on cathode and anode was different due to the action of gravity and arc erosion.Furthermore,the relationships among arc energy,arc time,welding force,electric resistivity,temperature and mass change on contacts were discussed,which indicated that the mass loss on cathode was mainly caused by the fracture of molten bridge.

Preparation of nano-structured Ag solid materials and application to surface-enhanced Raman scattering

Silver nano-particles with average diameter of about 60 nm were compacted in a high-strength mold under different pressures at 523 K to produce nano-structured Ag solid materials. The structure and characteristic of the nano-structured Ag solid materials (NSS-Ag) were studied using X-ray diffraction (XRD), scanning electron microscope (SEM) and Raman spectrometer. The NSS-Ag could be used as highly efficient surface-enhanced Raman scattering (SERS) active substrates. The common probe molecules Rhodamine 6G (R6G, 1×10-10 mol/L) were used to test the SERS activity on these substrates at very low concentrations. It is found that the SERS enhancement ability is dependent on the density of NSS-Ag. When the relative density of NSS-Ag is 83.87%, the materials reveal great SERS signal.

RECRYSTALLIZATION IN A SPINODAL Cu Ni Fe ALLOY

The interaction of spinodal decomposition and recrystallization process, and the characteristic of recrystallization in Cu-Ni-Fe alloy aged at different temperatures after solution-treatment and cold rolling have been studied by structural analysis and Vickers hardness test. It has shown that the recrystallization of spinodal Cu -Ni-Fe alloy might be divided into 2 types: spinodal decomposition, recovery and recrystallization of two-phase microstructure take place in the deformed alloy aged below the spinodal temperature; while recrystallization of single-phase microstructure and growth of fully-recrystallized grains take place in the deformed alloy aged above the spinodal temperature. The deformed alloy aged below the spinodal temperature recrystallizes in cellular morphology.

MODULATED STRUCTURES AND ORDERING STRUCTURES IN ALLOYING AUSTENITIC MANGANESE STEEL

The microstructure of Fe-10Mn-2Cr-1.5C alloy has been investigated with transmission electron microscopy and X-ray diffractometer. The superlattice diffraction spots and satellite reflection patterns have been observed in the present alloy, which means the appearance of the ordering structure and the modulated structure in the alloy. It is also proved by X-ray diffraction analysis that the austenite in the alloy is more stable than that in traditional austenitic manganese steel. On the basis of this investigation, it is suggested that the C-Mn ordering clusters exist in the austenitic manganese steel and the chromium can strengthen this effect by linking the weaker C-Mn couples together, which may play an important role in work hardening of the austenitic manganese steel.

An Optical Investigation of Silver Nanoclusters Composite Soda-lime Glass Formed by Electric Field Assisted Diffusion

Silver nanoclusters（NCs） embedded in soda-lime glass was synthesized by the electric fieldassisted diffusion（EFAD） and successive annealing. The samples were characterized by UV-Vis absorption spectroscopy, photoluminescence spectroscopy, X-ray photoelectron spectroscopy（XPS）, and lifetime measurements. The experimental results show that the growth of silver clusters is favored by the annealing temperature and dwell time. The as-diffused and annealed glass samples show photoluminescence around 550 nm under UV excitation, which can be associated with the presence of L-center and Ag3~＋ cluster. And the increasing of the annealing temperature and dwell time results in an appearance of the SPR peak and the decreasing of the luminescence intensities because the Ag3~＋ clusters grow up into the Ag nanoparticles.