Experimental study on remodeling strength of granular materials under different loads and lengths of time

Remodeled clay and sand rock specimens were prepared by designing lateral confinement and water drainage experiments based on the stress exerted on granular materials in a waste dump.An in situ test was conducted in an internal waste dump;the physical and mechanical parameters of the remodeled rock mass dumped at different time and depths were measured.Based on statistics,regression analysis was performed with regard to the shearing stress parameters acquired from the two tests.Other factors,such as remodeling pressure(burial depth),remodeling time(amount of time since waste was dumped),and the corresponding functional relationship,were determined.Analysis indicates that the cohesion of the remodeled clay and its remodeling pressure are correlated by a quadratic function but are not correlated with remodeling time length.In situ experimental results indicate that the shear strength of reshaped granular materials in the internal dump is positively correlated with burial depth but poorly correlated with time length.Cohesion Cand burial depth H follow a quadratic function,specifically for a short time since waste has been dumped.As revealed by both in situ and laboratory experiments,the remodeling strength of granular materials varies in a certain pattern.The consistency of such materials verifies the reliability of the remodeling experimental program.

A STUDY OF THE POSTBUCKLING PATH OF CYLINDRICALLY CURVED PANELS OF LAMINATED COMPOSITE MATERIALS DURING LOADING AND UNLOADING

In this paper, Dynamic Relaxation Method is applied to study the postbuckling path of cylindrically curved panels of laminated composite materials during loading and unloading. The phenomenon that loading paths do not coincide with unloading paths has been found. Numerical results are given for cylindrically curved cross-ply panels subjected to uniform uniaxial compression under two types of boundary conditions. The influence of the number of layers, the panels curvature and the initial imperfection on the postbuckling paths is discussed.

Hot Spot in Materials with Structural Defects under High Shear Loading Rates

The response of three-dimensional sample of Al, containing vacancy complex, under shear loading was simulated. The molecular dynamics method was used and interaction between atoms was described on the base of pseudopotential theory Solitary waves were generated in the sample under mechanical loading. Their interaction with the vacancy complexes was shown to be able to initiate hot spot in that local region of the complexes. Some parameters of the hot spot as well as solitary waves were calculated. The initiation of the hot spot is accompanied with sufficient local structural relaxation.

The Stress Analysis for Notched Specimen of Brittle Material under Plane Dead Loading

The stress distribution of notched specimen of brittle material under a plane pressure was studied using a photoelastic meth- od,When elastic deformation appeared inside the specimen,the force transferred by dowel part was triangular transverse force and frictional force on the upper surface of the sample.The quantity of the frictional force was about 31 percent of transverse force.The stress inside the sample was linear along the central cross section of the sample and there was maximum tensile stress σ_y at the tip of the notch.Basing on shearing stress deviation method,the tensile stress σ_y,σ_x and shearing stress τ_(xy) at the cen- tral sections and four adjacent cross sections were calculated.The result pointed out that σ_x and τ_(xy) were smaller than σ_y.There- fore,σ_y was the main factor for crack formation and propagation.

Influence of Specimen Size on Compression Behavior of Cement Paste and Mortar under High Strain Rates

Static and dynamic compression tests were carried out on mortar and paste specimens of three sizes（Ф68 mm×32 mm,Ф59 mm×29.5 mm and Ф32 mm×16 mm）to study the influence of specimen size on the compression behavior of cement-based materials under high strain rates.The static tests were applied using a universalservo-hydraulic system,and the dynamic tests were applied by a spilt Hopkinson pressure bar（SHPB）system.The experimentalresults show that for mortar and paste specimens,the dynamic compressive strength is greater than the quasi-static one,and the dynamic compressive strength for specimens of large size is lower than those of smallsize.However,the dynamic increase factors（DIF）has an opposite trend.Obviously,both strain rate and size effect exist in mortar and paste.The test results were then analyzed using Weibull,Carpinteriand Ba？ant＇s size effect laws.A good agreement between these three laws and the test results was reached on the compressive strength.However,for the experimentalresults of paste and cement mortar,the size effect is not evident for the peak strain and elastic modulus of paste and cement mortar.