A new design technique for the long life hot forging die has been proposed. By finite element analysis, the reason .for the failure of hot forging die was analyzed and it was concluded that thermal stress is the main ...A new design technique for the long life hot forging die has been proposed. By finite element analysis, the reason .for the failure of hot forging die was analyzed and it was concluded that thermal stress is the main reason for the failure of hot forging die. Based on this conclusion, the whole hot forging die was divided into the substrate part and the heat-resistant part according to the thermal stress distribution. Moreover, the heat-resistant part was further subdivided into more zones and the material of each zone was reasonably selected to ensure that the hot forging die can work in an elastic state. When compared with the existing techniques, this design can greatly increase the service life because the use of multi-materials can alleviate the thermal stress in hot forging die.展开更多
Titanium carbonitride based composite （TiCN-metallic binder） was developed as die material for replacement of cemented tungsten carbide. The effects of thermal conductivity characteristic of the TiCN composite on ho...Titanium carbonitride based composite （TiCN-metallic binder） was developed as die material for replacement of cemented tungsten carbide. The effects of thermal conductivity characteristic of the TiCN composite on hot forging performances were investigated using a servo press with ram motion control. Three types of the die materials; （a） tool steel for hot working, （b） cemented tungsten carbide with high thermal conductivity and （c） TiCN composite with low thermal conductivity were compared. In hot upsetting of a chrome steel workpiece, the TiCN composite die was confirmed to reduce the forging load by approximately 20% at slow forging speed. This is because the die with low thermal conductivity could prevent the workpiece from rapid cooling induced by heat transfer at the die-workpiece interface. In addition, the material flow of the workpiece to a die cavity was improved. Furthermore, the wear depth/wear coefficient of the TiCN composite was lower than that of the tool steel and the cemented tungsten carbide in the numerical analysis of wear due to the combination of low thermal conductivity and high hardness.展开更多
Half axle gears is produced by precision forging popularly because of the advantages in minimum machining allowances, lower material consumption and good service properties. But the forming quality of precision forgin...Half axle gears is produced by precision forging popularly because of the advantages in minimum machining allowances, lower material consumption and good service properties. But the forming quality of precision forging is difficult to control. Many simulations and analysis of precision forging process were taken by previous researchers. But no concrete method is proposed to evaluate and optimize the forming quality of half axel gears. The primary purpose of this work is improving the forming quality of half axel gears by analyzing and optimizing the affected factors of forming quality. The enclosed-die warm forging process of half axle gears was developed, and a new type of die-set used on double action hydraulic press was brought forward. The main influential factors of precision forming quality were analyzed after the forming process had been simulated by using finite element method（FEM）. These factors include die structure, web thickness and web position. A method used to evaluate the forming quality was established, which investigated the maximal forming load, the metal filling rate and the material damage factor. The FEM simulations of half axle gears precision forging were evaluated by this method. The results show that the best forming quality can be achieved when the punches were added with bosses, the web located at the middle plant of the gear, and the web thickness was 30 percent of the inner hole diameter. Verification experiments taking the above optimized parameters were performed on a 7.8 MN double action hydraulic press. The trial products were formed well. And their geometric precision meets the demand. The verification result shows that the optimization of the influential factors, according to the simulations and the evaluation method, can improve the forming quality. The new structure of precision forging die-set and the new evaluation method guarantee a high forming quality ofhalfaxel gears.展开更多
Lubricant is harmful to the mechanical properties of the sintered materials. Die wall lubrication was applied on warm compaction powder metallurgy in the hope of reducing the concentration level of the admixed lubrica...Lubricant is harmful to the mechanical properties of the sintered materials. Die wall lubrication was applied on warm compaction powder metallurgy in the hope of reducing the concentration level of the admixed lubricant. Iron based samples were prepared by die wall lubricated warm compaction at 175 ℃, using a compacting pressure of 550 MPa. Emulsified polytetrafluoroethylene(PTFE) was used as die wall lubricant. Admixed lubricant concentration ranging from 0 to 0.5% was tested. Extremely low admixed lubricant contents were used. Results show that in addition to the decrease in ejection forces, the green density of the compacts increases with the decrease of admixed lubricant content until it reaches the maximum at 0.06% of lubricant content, then decreases with the decrease of admixed lubricant content. The mechanical properties of the sintered compacts that contain more than 0.06% admixed lubricant are better than those of the samples that contain lesser lubricant. No scoring was observed in all die wall lubricated experiments.展开更多
Iron-based powder metallurgy material was prepared by warm compaction at 125 ℃ using a compacting pressure of 700 MPa. Sintering temperature ranging from 1 100 ℃ to 1 300 ℃ and sintering time ranging from 40 min to...Iron-based powder metallurgy material was prepared by warm compaction at 125 ℃ using a compacting pressure of 700 MPa. Sintering temperature ranging from 1 100 ℃ to 1 300 ℃ and sintering time ranging from 40 min to 80 min were used to study the effects of sintering parameters on the compacts. Die wall lubrication polytetrafluoroethylene(PTFE) emulsion was also applied in combination with warm compaction in hope to increase the compact density and the mechanical properties of the sintered material. Green and sintered density, spring back effect and sinter shrinkage were measured. Mechanical properties of both as-sinter and heat treated samples were also measured. Results show that mechanical properties of the sintered compacts increase with the increase of sintering temperature and sintering time. Sample prepared by die wall lubricated warm compaction always shows higher density and mechanical properties.展开更多
The cracking morphology of the hardfacing specimens taken from steel 5CrNiMo was observed. Meanwhile, the residual stress fields were measured and simulated. Based on experiment mentioned above, the improved structure...The cracking morphology of the hardfacing specimens taken from steel 5CrNiMo was observed. Meanwhile, the residual stress fields were measured and simulated. Based on experiment mentioned above, the improved structure and modified inclusion in hardfacing metal with rare earth （RE） oxide were analyzed. The results show that, the hardfacing crack is initiated from the coarse dendritic crystal grain boundary, inclusions and coarse austenite grain boundary in the HAZ and propagated by the residual stress existing in the center of the hardfacing metal and HAZ. The primary columnar grain structure can be refined by adding RE oxide in the coating of the electrode. The inclusion in the hardfacing metal can be modified as well. Meanwhile, if the martensite transformation temperature is decreased, the largest value of the residual tensile stress in the dangerous region can be reduced.展开更多
基金the National Natural Science Foundation of China （No. 50675165）.
文摘A new design technique for the long life hot forging die has been proposed. By finite element analysis, the reason .for the failure of hot forging die was analyzed and it was concluded that thermal stress is the main reason for the failure of hot forging die. Based on this conclusion, the whole hot forging die was divided into the substrate part and the heat-resistant part according to the thermal stress distribution. Moreover, the heat-resistant part was further subdivided into more zones and the material of each zone was reasonably selected to ensure that the hot forging die can work in an elastic state. When compared with the existing techniques, this design can greatly increase the service life because the use of multi-materials can alleviate the thermal stress in hot forging die.
文摘Titanium carbonitride based composite （TiCN-metallic binder） was developed as die material for replacement of cemented tungsten carbide. The effects of thermal conductivity characteristic of the TiCN composite on hot forging performances were investigated using a servo press with ram motion control. Three types of the die materials; （a） tool steel for hot working, （b） cemented tungsten carbide with high thermal conductivity and （c） TiCN composite with low thermal conductivity were compared. In hot upsetting of a chrome steel workpiece, the TiCN composite die was confirmed to reduce the forging load by approximately 20% at slow forging speed. This is because the die with low thermal conductivity could prevent the workpiece from rapid cooling induced by heat transfer at the die-workpiece interface. In addition, the material flow of the workpiece to a die cavity was improved. Furthermore, the wear depth/wear coefficient of the TiCN composite was lower than that of the tool steel and the cemented tungsten carbide in the numerical analysis of wear due to the combination of low thermal conductivity and high hardness.
基金supported by Chongqing Municipal Science and Technology Committee of China (Grant No. 2005AA3012-4)
文摘Half axle gears is produced by precision forging popularly because of the advantages in minimum machining allowances, lower material consumption and good service properties. But the forming quality of precision forging is difficult to control. Many simulations and analysis of precision forging process were taken by previous researchers. But no concrete method is proposed to evaluate and optimize the forming quality of half axel gears. The primary purpose of this work is improving the forming quality of half axel gears by analyzing and optimizing the affected factors of forming quality. The enclosed-die warm forging process of half axle gears was developed, and a new type of die-set used on double action hydraulic press was brought forward. The main influential factors of precision forming quality were analyzed after the forming process had been simulated by using finite element method（FEM）. These factors include die structure, web thickness and web position. A method used to evaluate the forming quality was established, which investigated the maximal forming load, the metal filling rate and the material damage factor. The FEM simulations of half axle gears precision forging were evaluated by this method. The results show that the best forming quality can be achieved when the punches were added with bosses, the web located at the middle plant of the gear, and the web thickness was 30 percent of the inner hole diameter. Verification experiments taking the above optimized parameters were performed on a 7.8 MN double action hydraulic press. The trial products were formed well. And their geometric precision meets the demand. The verification result shows that the optimization of the influential factors, according to the simulations and the evaluation method, can improve the forming quality. The new structure of precision forging die-set and the new evaluation method guarantee a high forming quality ofhalfaxel gears.
文摘Lubricant is harmful to the mechanical properties of the sintered materials. Die wall lubrication was applied on warm compaction powder metallurgy in the hope of reducing the concentration level of the admixed lubricant. Iron based samples were prepared by die wall lubricated warm compaction at 175 ℃, using a compacting pressure of 550 MPa. Emulsified polytetrafluoroethylene(PTFE) was used as die wall lubricant. Admixed lubricant concentration ranging from 0 to 0.5% was tested. Extremely low admixed lubricant contents were used. Results show that in addition to the decrease in ejection forces, the green density of the compacts increases with the decrease of admixed lubricant content until it reaches the maximum at 0.06% of lubricant content, then decreases with the decrease of admixed lubricant content. The mechanical properties of the sintered compacts that contain more than 0.06% admixed lubricant are better than those of the samples that contain lesser lubricant. No scoring was observed in all die wall lubricated experiments.
文摘Iron-based powder metallurgy material was prepared by warm compaction at 125 ℃ using a compacting pressure of 700 MPa. Sintering temperature ranging from 1 100 ℃ to 1 300 ℃ and sintering time ranging from 40 min to 80 min were used to study the effects of sintering parameters on the compacts. Die wall lubrication polytetrafluoroethylene(PTFE) emulsion was also applied in combination with warm compaction in hope to increase the compact density and the mechanical properties of the sintered material. Green and sintered density, spring back effect and sinter shrinkage were measured. Mechanical properties of both as-sinter and heat treated samples were also measured. Results show that mechanical properties of the sintered compacts increase with the increase of sintering temperature and sintering time. Sample prepared by die wall lubricated warm compaction always shows higher density and mechanical properties.
基金Project supported by Key Project of Science and Technology of Hebei Province (04212201D) and Research Foundationfor theReturned Overseas Chinese Scholars of State Education Ministry
文摘The cracking morphology of the hardfacing specimens taken from steel 5CrNiMo was observed. Meanwhile, the residual stress fields were measured and simulated. Based on experiment mentioned above, the improved structure and modified inclusion in hardfacing metal with rare earth （RE） oxide were analyzed. The results show that, the hardfacing crack is initiated from the coarse dendritic crystal grain boundary, inclusions and coarse austenite grain boundary in the HAZ and propagated by the residual stress existing in the center of the hardfacing metal and HAZ. The primary columnar grain structure can be refined by adding RE oxide in the coating of the electrode. The inclusion in the hardfacing metal can be modified as well. Meanwhile, if the martensite transformation temperature is decreased, the largest value of the residual tensile stress in the dangerous region can be reduced.
