Investigation on the Determination of Initial Shock Pressure at Near Interface Field of TNT Charge and Water for Underwater Explosion

There are few report on the directly measurement of the initial shock pressure of explosive charge at its interface of water for underwater explosion. The special technologies have been taken to the measurement system with manganin piezoresistive gauge （PRG） in order to measure the initial shock pressure at the interface and its near field of TNT chare and water. The free-holding PRG film gauge can directly determine the shock peak pressure at the interface and near field of TNT charge up to 12.85 GPa, which is satisfying for the good agreement to the 12.97 GPa with one dimensional theoretical analysis and 12.86 GPa with numerical simulation. The maximum discrepancy is 0.93 %. The results show that it is precise and reliable to determine the initial shock pressure of underwater explosion charge with the PRG technology.

Comparative study of the explosion pressure characteristics of micro- and nano-sized coal dust and methane–coal dust mixtures in a pipe

Coal dust explosion accidents often cause substantial property damage and casualties and frequently involve nano-sized coal dust.In order to study the impact of nano-sized coal on coal dust and methane–coal dust explosions,a pipe test apparatus was used to analyze the explosion pressure characteristics of five types of micro-nano particle dusts(800 nm,1200 nm,45μm,60μm,and 75μm)at five concentrations(100 g/m3,250 g/m3,500 g/m3,750 g/m3,and 1000 g/m3).The explosion pressure characteristics were closely related to the coal dust particle size and concentration.The maximum explosion pressure,maximum rate of pressure rise,and deflagration index for nano-sized coal dust were larger than for its micro-sized counterpart,indicating that a nano-sized coal dust explosion is more dangerous.The highest deflagration index Kst for coal dust was 13.97 MPa/(m·s),indicating weak explosibility.When 7%methane was added to the air,the maximum deflagration index Kst for methane–coal dust was 42.62 MPa/(m·s),indicating very strong explosibility.This indicates that adding methane to the coal dust mixture substantially increased the hazard grade.

Effect of particle size of coal dust on explosion pressure

The effect of the particle size of coal dust on explosion pressure and the rising rate of explosion pressure is studied. Three coal dusts from Lingan Coal Mine in Canada and Datong Coal Mine in China are selected to test. The influence of particle size on the maximum explosion pressure P max and maximum pressure rising rate (d p /d t ) max of each coal dust was tested experimentally. The results indicate that with the decrease of particle size of coal dusts, explosion pressure increases on condition of the same concentration. If the concentration of coal dust is different, the maximum explosion pressure appears at the concentration of 500 g/m^3. The smaller the particle size of coal dusts, the larger the rising rate of explosion pressure of coal dust. When the concentration of coal dust is 500 g/m^3, the rising rate of explosion pressure of each coal dust is the maximum.

The Influence of Various Structure Surface Boundary Conditions on Pressure Characteristics of Underwater Explosion

The shock wave of the underwater explosion can cause severe damage to the ship structure.The propagation characteristics of shock waves near the structure surface are complex,involving lots of complex phenomena such as reflection,transmission,diffraction,and cavitation.However,different structure surface boundaries have a significant effect on the propagation characteristics of pressure.This paper focuses on investigating the behavior of shock wave propagation and cavitation from underwater explosions near various structure surfaces.A coupled Runge–Kutta discontinuous Galerkin(RKDG)and finite elementmethod(FEM)is utilized to solve the problem of the complex waves of fluids and structure dynamic response,considering the fluid compressibility.The level set(LS)method and the ghost fluid(GF)method are combined to capture the moving interface and deal with the stability of the coupling between the shock wave and structure surface.Besides,a cut-off cavitation model is introduced to the RKDG method.The validation of the numerical calculation model is discussed by comparing it with the known solution to verify the numerical solutions.Then,crucial kinds of structure surface boundary conditions include shallow-water single layer elasticity plate,double-layer crevasse elasticity plate,single layer curved elasticity plate,and double-layer curved elasticity plates are analyzed and discussed.The results and analysis can provide references for underwater explosion pressure characteristics,the impacting response of different boundary structures,and designing structures.

Second Discharge Characteristics of Aluminum Wire Electrical Explosion Under Various Argon Pressures

Electrical wire explosion is a promising method for the preparation of metal nanopowder, but the properties of metal nanopowder are affected by the second discharge process of electrical wire explosion. The second discharge characteristics of aluminum wire electrical ex- plosion under variant argon pressures were studied in a RLC discharge circuit. The results show that the curve of the second discharge voltages versus the pressure presents a U-shape. To clarify the roles of aluminum vapor and argon in the process of the second discharge, a spectrograph and a high speed framing camera were used to study the radiation spectrum and spatial distribution of the electrical explosion plasma. It is observed that argon participates in the second discharge process under low pressure. A discharge channel develops along the surface of the aluminum vapor. Under higher pressure, a second discharge takes place in the aluminum vapor and the discharge channel is inside the aluminum vapor.

Study of relieving weld residual stresses in large pressure steel pipes of hydropower station by local explosion treatment

From comparing the test of local explosion treatment(LET)with the locaf heat treatment (LHT)in welded plates and welded steel pipes in field,LET has excellent effect of stress relief and high efficiency. Whereas the effect of stress relief for LHT with 575℃×1.5hr is poor.The mechanical properties of welded joints after LET are basically the same as those of as-welded joints.The practically measuring results on 4 large steel-pipe surfaces indicate that the welding residual tensile stresses in welds,which mostly is compression residual stress,are basically relieved.

A novel method for simulating nuclear explosion with chemical explosion to form an approximate plane wave: Field test and numerical simulation

A nuclear explosion in the rock mass medium can produce strong shock waves,seismic shocks,and other destructive effects,which can cause extreme damage to the underground protection infrastructures.With the increase in nuclear explosion power,underground protection engineering enabled by explosion-proof impact theory and technology ushered in a new challenge.This paper proposes to simulate nuclear explosion tests with on-site chemical explosion tests in the form of multi-hole explosions.First,the mechanism of using multi-hole simultaneous blasting to simulate a nuclear explosion to generate approximate plane waves was analyzed.The plane pressure curve at the vault of the underground protective tunnel under the action of the multi-hole simultaneous blasting was then obtained using the impact test in the rock mass at the site.According to the peak pressure at the vault plane,it was divided into three regions:the stress superposition region,the superposition region after surface reflection,and the approximate plane stress wave zone.A numerical simulation approach was developed using PFC and FLAC to study the peak particle velocity in the surrounding rock of the underground protective cave under the action of multi-hole blasting.The time-history curves of pressure and peak pressure partition obtained by the on-site multi-hole simultaneous blasting test and numerical simulation were compared and analyzed,to verify the correctness and rationality of the formation of an approximate plane wave in the simulated nuclear explosion.This comparison and analysis also provided a theoretical foundation and some research ideas for the ensuing study on the impact of a nuclear explosion.

Influence of an emulsifier on the pressure desensitization of emulsion explosives

The desensitization degree of emulsion explosives （EE） was calculated with the peak pressure of explosion shock waves tested in water. To an explosive, the less the desensitization degree, the better the compression resistance, so the compression resistance of an explosive can be compared and analyzed quantificationally with the desensitization degree. The influence of an emulsifier on the pressure desensitization of EE was studied, including the content and category of emulsifiers. Three kinds of emulsifiers （Span-80, compound emulsifier, and T-152） were used in the tests. The experimental results show that both the content and category of emulsifiers make a great effect on the pressure desensitization of EE. The desensitization degree of EE reduces with the emulsifier content being increased, but there is an optimal content of an emulsifier for the compression resistance of EE. While the content of Span-80 reaches 4wt%, the desensitization degree of EE becomes a minimal value, and augments somewhat if the emulsifier content is increased more. That is to say, the compression resistance of EE becomes the highest while the content of Span-80 is 4wt%, and the compression resistance will decline if the content of Span-80 is increased more. The compression resistance of the explosive emulsified by compound emulsifier is the highest among all the explosives, when the content of the whole components and manufacturing engineering are kept invariable.

Effect of hydrogen-storage pressure on the detonation characteristics of emulsion explosives sensitized by glass microballoons

In this study,hydrogen-storage glass microballoons were introduced into emulsion explosives to improve the detonation performance of the explosives.The effect of hydrogen-storage pressure on the detonation characteristics of emulsion explosives was systematically investigated.Detonation velocity experiments shows that the change of sensitizing gas and the increase of hydrogen pressure have different effects on the detonation velocity.The experimental parameters of underwater explosion increase first and then decreases with the increase of hydrogen pressure.The decrease of these parameters indicates that the strength of glass microballoons is the limiting factor to improve the detonation performance of hydrogen-storage emulsion explosives.Compared with the traditional emulsion explosives,the maximum peak pressure of shock wave of hydrogen-storage emulsion explosives increases by 10.6%at 1.0 m and 10.2%at 1.2 m,the maximum values of shock impulse increase by 5.7%at 1.0 m and 19.4%at 1.2 m.The stored hydrogen has dual effects of sensitizers and energetic additives,which can improve the energy output of emulsion explosives.

Electric-controlled pressure relief valve for enhanced safety in liquid-cooled lithium-ion battery packs

The liquid-cooled battery energy sto rage system(LCBESS) has gained significant attention due to its superior thermal management capacity.However,liquid-cooled battery pack(LCBP) usually has a high sealing level above IP65,which can trap flammable and explosive gases from battery thermal runaway and cause explosions.This poses serious safety risks and challenges for LCBESS.In this study,we tested overcharged battery inside a commercial LCBP and found that the conventionally mechanical pressure relief valve(PRV) on the LCBP had a delayed response and low-pressure relief efficiency.A realistic 20-foot model of an energy storage cabin was constructed using the Flacs finite element simulation software.Comparative studies were conducted to evaluate the pressure relief efficiency and the influence on neighboring battery packs in case of internal explosions,considering different sizes and installation positions of the PRV.Here,a newly developed electric-controlled PRV integrated with battery fault detection is introduced,capable of starting within 50 ms of the battery safety valve opening.Furthermore,the PRV was integrated with the battery management system and changed the battery charging and discharging strategy after the PRV was opened.Experimental tests confirmed the efficacy of this method in preventing explosions.This paper addresses the safety concerns associated with LCBPs and proposes an effective solution for explosion relief.

Experimental research on influence of emulsifier on crystallization quantity of emulsion explosives under dynamic pressure

Dynamic pressure was applied on emulsion explosive by using an underwater explosion measuring apparatus, and the crystallization quantity was measured by dissolution method after emulsion explosive was pressed; the influence of emulsi- fier content and type was analyzed. The experimental results show that emulsifier content and type have an important effect on crystallization quantity of emulsion explosive. The crystallization quantity will reduce with Span-g0 content from 2% to 4%, so the demulsification and crystallization will decrease if the emulsifier content improves appropriately and the dynamic pressure resistance will increase. For emulsion explosive emulsified by T-152 and Span-g0, the crystallization quantity with T-152 is less than that of Span-g0 under the same dynamic pressure. This shows that the emulsifying effect ofT-152 is better than Soan-80.

Design and theoretical analysis of test system for propellants' gas pressure in warhead

Aiming at harsh environment of cluster bombs center tube explosion dispersion and difficulties in installation of traditional test systems,a storage test system based on 16-bit ultra-low power microcontroller MSP430 is designed in order to acquire gas pressure during cluster bombs dispersion.To meet the requirement of low power consumption,the working states of system＇s modules during data acquisition are elaborated and the equation to calculate the gas pressure change during cylindrical center tube opening the hatch is deduced.The field test is conducted and good test results are obtained.

Study on liquefaction of saturated loess by in-situ explosion test

Liquefaction testing at a saturated loess site was performed under the simulated earthquake ground motion induced by artificial explosions with micro-time intervals.The time histories of ground acceleration,pore water pressure and the ultimate value of residual strain were recorded and measured.The modified FEQdrain computation software was used to analyze the liquefaction.Both the test and the analysis confirm the objective occurrence of loess liquefaction.Furthermore,the reliability of the method of the loess liquefaction analysis based on FEQdrain and the model of pore water pressure development of saturated loess are examined.

Research on the explosion characteristics of chlorine dioxide gas

The explosion characteristics of chlorine dioxide gas have been studied for the first time in a cylindrical exploder with a shell capacity of 201. The experimental results have indicated that the lower concentration limit for the explosive decomposition of chlorine dioxide gas is 9.5% （[ClO2]/[air]）, whereas there is no corresponding upper concentration limit. The maximum pressure of explosion relative to the initial pressure was measured as 0.024 MPa at 10% ClO2 and 0.641 MPa at 90% ClO2. The induction time （the time from the moment of sparking to explosion） at 10% ClO2 was 2195 ms, but at 90% ClO2 the induction time was just 8 ms. The explosion reaction mechanism of ClO2 is of a degenerate chain-branching type involving the formation of a stable intermediate （Cl2O3）, from which the chain branching occurs.

Hazard evaluation of ignition sensitivity and explosion severity for three typical MH_(2) (M=Mg,Ti,Zr)of energetic materials

MgH_(2),TiH_(2),and ZrH_(2) are three typical metal hydrides that have been gradually applied to composite explosives and propellants as additives in recent years.To evaluate ignition sensitivity and explosion severity,the Hartmann device and spherical pressure vessel were used to test ignition energy and explosion pressure,respectively.The results showed that the ignition sensitivity of ZrH_(2),TiH_(2) and MgH_(2) gradually increased.When the concentration of MgH_(2) is 83.0 g/m^(3) in Hartmann device,the ignition energy attained a minimum of 10.0 mJ.The explosion pressure of MgH_(2) were 1.44 times and 1.76 times that of TiH_(2) and ZrH_(2),respectively,and the explosion pressure rising rate were 3.97 times and 9.96 times that of TiH_(2) and ZrH_(2),respectively,through the spherical pressure vessel.It indicated that the reaction reactivity and reaction rate of MgH_(2) were higher than that of TiH_(2) and ZrH_(2).In addition,to conduct in edepth theoretical analysis of ignition sensitivity and explosion severity,gas production and combustion heat per unit mass of ZrH_(2),TiH_(2) and MgH_(2) were tested by mercury manometer and oxygen bomb calorimetry.The experimental results revealed that MgH_(2) had a relatively high gas production per unit mass(5.15 mL/g),while TiH_(2) and ZrH_(2) both had a gas production of less than 2.0 mL/g.Their thermal stability gradually increased,leading to a gradual increase in ignition energy.Furthermore,compared with theoretical combustion heat,the combustion ratio of MgH_(2),TiH_(2) and ZrH_(2) was more than 96.0%,with combustion heat value of 29.96,20.94 and 12.22 MJ/kg,respectively,which was consistent with the explosion pressure and explosion severity test results.

Mechanical Model of Domestic Gas Explosion Load

With the increase of domestic gas consumption in cities and towns in China,gas explo-sion accidents happened rather frequently,and many structures were damaged greatly.Rational physical design could protect structures from being destroyed,but the character of explosion load must be learned firstly by establishing a correct mechanical model to simulate vented gas explo-sions.The explosion process has been studied for many years towards the safety of chemical in-dustry equipments.The key problem of these studies was the equations usually involved some ad-justable parameters that must be evaluated by experimental data,and the procedure of calculation was extremely complicated,so the reliability of these studies was seriously limited.Based on these studies,a simple mathematical model was established in this paper by using energy conservation,mass conservation,gas state equation,adiabatic compression equation and gas venting equation.Explosion load must be estimated by considering the room layout; the rate of pressure rise was then corrected by using a turbulence factor,so the pressure-time curve could be obtained.By using this method,complicated calculation was avoided,while experimental and calculated results fitted fairly well.Some pressure-time curves in a typical rectangular room were calculated to inves-tigate the influences of different ignition locations,gas thickness,concentration,room size and venting area on the explosion pressure.The results indicated that: it was the most dangerous con-dition when being ignited in the geometry centre of the room; the greater the burning velocity,the worse the venting effect; the larger the venting pressure,the higher the peak pressure; the larger the venting area,the lower the peak pressure.

Vacuum chamber suppression of gas-explosion propagation in a tunnel

To control and reduce the harm of a gas explosion, a new method is proposed for suppressing gas-explosion propagation in a tunnel by using a vacuum chamber. We studied the suppression effect on gas explosions by placing a vacuum chamber at dif-ferent positions along the tunnel. The results indicate that: 1) the vacuum chamber can absorb the explosion wave and explosion energy as much as possible at the beginning of the gas explosion, and; 2) when the vacuum chamber is used the closer it is to the ignition source the more significant the suppression effect. In addition, by using the vacuum chamber: 1) the flame propagation velocity decreases from ultrasonic to subsonic; 2) the flame propagation distance is remarkably shortened; 3) the maximum peak value of overpressure (pm) decreases from 0.34 to 0.17 MPa or less, and; 4) the impulse of the blast wave (I) decreases from 20 to 8 kPa·s or less.

Blast Pressure Measurements of an Underwater Detonation in the Sea

Blast pressure measurements of a controlled underwater explosion in the sea were carried out.An explosive of 25-kg trinitro-toluene(TNT)equivalent was detonated,and the blast pressures were recorded by eight diferent high-performance pressure sensors that work at the nonresonant high-voltage output in adverse underwater conditions.Recorded peak pressure values are used to establish a relationship in the well-known form of empirical underwater explosion(UNDEX)loading formula.Constants of the formula are redetermined by employing the least-squares method in two diferent forms for best ftting to the measured data.The newly determined constants are found to be only slightly diferent from the generally accepted ones.

Experimental and numerical evaluations on characteristics of vented methane explosion

To research the characteristics of vented explosion of methane-air mixture in the pipeline,coal mine tunnel or other closed space,the experiments and numerical simulations were carried out.In this work,explosion characteristics and flame propagation characteristics of methane in pipeline and coal mine tunnel are studied by using an explosion test system,combined with FLACS software,under different vented conditions.The numerical simulation results of methane explosion are basically consistent with the physical experiment results,which indicates that the numerical simulation for methane explosion is reliable to be applied to the practice.The results show that explosion parameters(pressure,temperature and product concentration)of methane at five volume fractions have the same change trend.Nevertheless,the explosion intension of 10.0%methane is the largest and that of 9.5%methane is relatively weak,followed by 11.0%methane,8.0%methane and 7.0%methane respectively.Under different vented conditions,the pressure and temperature of methane explosion are the highest in the pipeline without a vent,followed by the pipeline where ignition or vent position is in each end,and those are the lowest in the pipeline with ignition and vent at the same end.There is no significant effect on final product concentration of methane explosion under three vented conditions.For coal mine tunnel,it is indicated that the maximum explosion pressure at the airproof wall in return airway with the branch roadway at 50 m from goaf is significantly decreased while that in intake airway does not change overwhelmingly.In addition,when the branch roadway is longer or its section is larger,the peak pressure of airproof wall reduces slightly.

Nonlinear Dynamic Response of a Fixed Offshore Platform Subjected to Underwater Explosion at Different Distances

In this paper,the dynamic response of a fixed offshore platform subjected to the underwater explosion(UNDEX)and probable events following it have been investigated.The pressure load due to UNDEX in a specified depth has been applied with a model that considers the effect of blast bubble fluctuations into account.The effect of water on the natural frequency and Fluid-Structure interaction has been modeled as equivalent added mass formulation.The effect of explosion distance on platform response is studied.In this regard,three cases of near,medium,and far-distance explosions are considered.For a case study,a real fixed offshore jacket platform,installed in the Persian Gulf,has been examined.Only the UNDEX pressure load is considered and other dynamic loads such as surface water waves and winds have been neglected.Dead loads,live loads and hydrostatic pressure has been considered in the static case based on the design codes.The results indicated that in near-distance explosions,the UNDEX pressure load can locally damage parts of the platform that are located at the same level as that of explosive material and it can destabilize the platform.In the medium to far distance explosion,a very large base shear was applied to the platform because more elements were exposed to the UNDEX load compared to the near-distance explosion.Therefore,precautionary measures against UNDEX such as risk assessment according to design codes are necessary.As a result of this,member strengthening against explosion may be required.