The presence of toxic elements in manganese slag(MSG)poses a threat to the environment due to potential pollution.Utilizing CO_(2) curing on MS offers a promising approach to immobilize toxic substances within this ma...The presence of toxic elements in manganese slag(MSG)poses a threat to the environment due to potential pollution.Utilizing CO_(2) curing on MS offers a promising approach to immobilize toxic substances within this material,thereby mitigating their release into the natural surroundings.This study investigates the impact of CO_(2) cured MS on various rheological parameters,including slump flow,plastic viscosity(η),and yield shear stress(τ).Additionally,it assesses flexural and compressive strengths(f_(t) and f_(cu)),drying shrinkage rates(DSR),durability indicators(chloride ion migration coefficient(CMC),carbonization depth(CD)),and the leaching behavior of heavy metal elements.Microscopic examination via scanning electron microscopy(SEM)is employed to elucidate the underlying mechanisms.The results indicate that CO_(2) curing significantly enhances the slump flow of ultra-high performance concrete(UHPC)by up to 51.2%.Moreover,it reduces UHPC’sηandτby rates ranging from 0%to 52.7%and 0%to 40.2%,respectively.The DSR exhibits a linear increase corresponding to the mass ratio of CO_(2) cured MS.Furthermore,CO_(2) curing enhances both f_(t) and f_(cu) of UHPC by up to 28.7%and 17.6%,respectively.The electrical resistance is also improved,showing an increase of up to 53.7%.The relationship between mechanical strengths and electrical resistance follows a cubic relationship.The CO_(2) cured MS demonstrates a notable decrease in the CMC and CD by rates ranging from 0%to 52.6%and 0%to 26.1%,respectively.The reductions of leached chromium(Cr)and manganese(Mn)are up to 576.3%and 1312.7%,respectively.Overall,CO_(2) curing also enhances the compactness of UHPC,thereby demonstrating its potential to improve both mechanical and durability properties.展开更多
Despite advancements in silicon-based anodes for high-capacity lithium-ion batteries,their widespread commercial adoption is still hindered by significant volume expansion during cycling,especially at high active mass...Despite advancements in silicon-based anodes for high-capacity lithium-ion batteries,their widespread commercial adoption is still hindered by significant volume expansion during cycling,especially at high active mass loadings crucial for practical use.The root of these challenges lies in the mechanical instability of the material,which subsequently leads to the structural failure of the electrode.Here,we present a novel synthesis of a composite combining expanded graphite and silicon nanoparticles.This composite features a unique interlayer-bonded graphite structure,achieved through the application of a modified spark plasma sintering method.Notably,this innovative structure not only facilitates efficient ion and electron transport but also provides exceptional mechanical strength(Vickers hardness:up to658 MPa,Young's modulus:11.6 GPa).This strength effectively accommodates silicon expansion,resulting in an impressive areal capacity of 2.9 mA h cm^(-2)(736 mA h g^(-1)) and a steady cycle life(93% after 100cycles).Such outsta nding performance is paired with features appropriate for large-scale industrial production of silicon batteries,such as active mass loading of at least 3.9 mg cm^(-2),a high-tap density electrode material of 1.68 g cm^(-3)(secondary clusters:1.12 g cm^(-3)),and a production yield of up to 1 kg per day.展开更多
This work explored possibilities of biodegradable magnesium alloy Mg-3Y preparation by two modern powder metallurgy techniques–spark plasma sintering(SPS)and selective laser melting(SLM).The powder material was conso...This work explored possibilities of biodegradable magnesium alloy Mg-3Y preparation by two modern powder metallurgy techniques–spark plasma sintering(SPS)and selective laser melting(SLM).The powder material was consolidated by both methods utilising optimised parameters,which led to very low porosity(∼0.3%)in the SLM material and unmeasurably low porosity in the SPS material.The main aim of the study was the thorough microstructure characterisation and interrelation between the microstructure and the functional properties,such as mechanical strength,deformability,and corrosion resistance.Both materials showed comparable strength of∼110 MPa in tension and compression and relatively good deformability of∼9%and∼21%for the SLM and SPS materials,respectively.The corrosion resistance of the SPS material in 0.1 M NaCl solution was superior to the SLM one and comparable to the conventional extruded material.The digital image correlation during loading and the cross-section analysis of the corrosion layers revealed that the residual porosity and large strained grains have the dominant negative effect on the functional properties of the SLM material.On the other hand,one of the primary outcomes of this study is that the SPS consolidation method is very effective in the preparation of the W3 biodegradable alloy,resulting in material with convenient mechanical and degradation properties that might find practical applications.展开更多
The remarkable properties of carbon nanotubes(CNTs)have led to promising applications in the field of electromagnetic inter-ference(EMI)shielding.However,for macroscopic CNT assemblies,such as CNT film,achieving high ...The remarkable properties of carbon nanotubes(CNTs)have led to promising applications in the field of electromagnetic inter-ference(EMI)shielding.However,for macroscopic CNT assemblies,such as CNT film,achieving high electrical and mechanical properties remains challenging,which heavily depends on the tube-tube interac-tions of CNTs.Herein,we develop a novel strategy based on metal-organic decomposition(MOD)to fabricate a flexible silver-carbon nanotube(Ag-CNT)film.The Ag particles are introduced in situ into the CNT film through annealing of MOD,leading to enhanced tube-tube interactions.As a result,the electrical conductivity of Ag-CNT film is up to 6.82×10^(5) S m^(-1),and the EMI shielding effectiveness of Ag-CNT film with a thickness of~7.8μm exceeds 66 dB in the ultra-broad frequency range(3-40 GHz).The tensile strength and Young’s modulus of Ag-CNT film increase from 30.09±3.14 to 76.06±6.20 MPa(~253%)and from 1.12±0.33 to 8.90±0.97 GPa(~795%),respectively.Moreover,the Ag-CNT film exhibits excellent near-field shield-ing performance,which can effectively block wireless transmission.This innovative approach provides an effective route to further apply macroscopic CNT assemblies to future portable and wearable electronic devices.展开更多
Because inferior mechanical strength of granite polymer composite(GPC)has become the main drawback limiting its application and popularization,Mo fibers were added into(GPC)to improve its mechanical strength.Mechanica...Because inferior mechanical strength of granite polymer composite(GPC)has become the main drawback limiting its application and popularization,Mo fibers were added into(GPC)to improve its mechanical strength.Mechanical properties of matrix materials with different mass ratio of resin and stabilizer(MRRS)were investigated systematically.The influences of MRRS on interface bonding strength of Mo fiber-matrix,wettability and mechanical strength of GPC were discussed,respectively,and the theoretical calculation result of MRRS k was obtained,with the optimal value of k=4.When k=4,tensile strength,tensile strain and fracture stress of the cured resin achieve the maximum values.But for k=7,the corresponding values reach the minimum.With the increase of MRRS k,surface free energy of the cured resin first increases and then decreases,while contact angles between Mo sample and matrix have displayed the opposite trend.Wettability of resin to Mo fiber is the best at k=4.Pulling load of Mo fiber and interface bonding strength appear the maximum at k=4,followed by k=5,k=3 the third,and k=7 the minimum.When k=4,mechanical properties of Mo fiber-reinforced GPC are optimal,which is consistent with the result of theoretical calculation.This study is of great significance to get better component formulas of Mo fiber reinforced GPC and to improve its application in machine tools.展开更多
The mining process involves drilling and excavation, resulting in the production of waste rock and tailings. The waste materials are then removed and stored in designated areas. This study aims to evaluate the mechani...The mining process involves drilling and excavation, resulting in the production of waste rock and tailings. The waste materials are then removed and stored in designated areas. This study aims to evaluate the mechanical strength and the environmental and economic impact of using Coltan Mining Waste (CMW) as a substitute for aggregates in concrete and mortar production. To achieve this, the CMW needs to be characterised. The Dreux Gorisse method was primarily used to produce concrete with a strength of 20 MPa at 28 days. The mortars, on the other hand, were formulated according to the NF P 18-452 standard. The environmental impact of using CMW as substitutes for natural aggregates in the production of concrete and mortar was analysed using SimaPro software. The results showed that mortars and concrete made with CMW have comparable compressive strengths to the reference mortar and concrete;reduce the negative impact on ecosystem quality, human health, resources, and climate change. It has also been shown that the substitution of aggregates by CMW reduces the cost of concrete and mortar as a function of the distance from the aggregate footprint.展开更多
This work investigated the effect of sole yttrium and neodymium alloying on the microstructure formation during severe plastic deformation by equal channel angular pressing(ECAP) and an impact on the mechanical streng...This work investigated the effect of sole yttrium and neodymium alloying on the microstructure formation during severe plastic deformation by equal channel angular pressing(ECAP) and an impact on the mechanical strength and corrosion resistance of binary Mg-3Y and Mg-3Nd alloys.The results are compared with a ternary Mg-4Y-3Nd alloy,which represents a simplified version of the commercially successful WE43 alloy.The extensive study comprises a thorough microstructural analysis performed by scanning and transmission electron microscopy,including electron backscatter diffraction and texture analysis performed by X-ray diffraction.It is shown that the presence of Nd primarily caused precipitation during the processing of the Mg-3Nd alloy,while Y remained dissolved in the magnesium matrix in the Mg-3Y alloy.This difference resulted in a significantly smaller average grain size in the Mg-3Y alloy(~0.77 nm) than in the Mg-3Nd alloy(~1.3 μm) after the final step of the processing and formation of a slightly different texture.Consequently,the composition and the processing affected the mechanical and corrosion properties of the investigated materials,measured by compression deformation tests,microhardness measurement,and electrochemical impedance spectroscopy.This study shows that the ECAP-processed W3 sample exhibits a surprisingly good combination of ultrafine-grain structure,weak crystallographic texture,high strength,and high corrosion resistance compared with the other investigated samples.These attributes make this material very interesting for utilisation in the industry and/or medicine.展开更多
Montmorillonite and clinoptilolite zeolite were used as representative materials to prepare calcined clay-cement binary cementitious materials in order to study the effect of calcination treatment on the activation of...Montmorillonite and clinoptilolite zeolite were used as representative materials to prepare calcined clay-cement binary cementitious materials in order to study the effect of calcination treatment on the activation of clay minerals and the activity difference between layered and framed clays in this research.The influence of different calcined clay content(2%,4%,6%,8%,10%)on the fluidity,compressive strength,microstructure,phase change,and hydration heat of cement-based materials were analyzed.The calcined clay improves the fluidity of cement-based materials as compared with the uncalcined group.The addition of calcined montmorillonite(CMT)improves the development of mechanical strength,and the optimal compressive strength reaches 85 MPa at 28 days with 8%CMT.However,the activity of calcined clinoptilolite zeolite(CZL)is weak with few reaction sites,which slightly reduced the mechanical strength as compared to the blank sample.The addition of CMT changes the microscopic morphology of hydration products such as C-S-H and C-A-H,leading to the formation and transformation of ettringite in the early stage.It promotes the gradual polymerization of Si-O bonds into Si-O-Si bonds simultaneously,which accelerates the early hydration process.However,CZL acts mainly as a filling function in the cementitious system.In brief,CMT as an admixture can improve the mechanical properties of cement,but CZL has little effect.This work provides a guideline for the applications of calcined clay in cement,considering the influence of clay type on workability and mechanical strength.展开更多
The aim of this study is to enhance the value and utilization of red mud generated in the Bayer process by preparing composite cement mortars.The effects of two different types of Bayer red mud with varying physical a...The aim of this study is to enhance the value and utilization of red mud generated in the Bayer process by preparing composite cement mortars.The effects of two different types of Bayer red mud with varying physical and chemical characteristics on the fluidity,mechanical strength,mineral composition,and microstructure of the composite cement mortar were systematically evaluated.The results showed that the optimal addition of red mud A was 10 wt%,while it was 20 wt% for red mud B.The mechanical properties of the composite cement mortar met the standards for P·O42.5 cement.Furthermore,the composite mortar with the addition of red mud B showed higher flexural and compressive strengths compared to the composite mortar with red mud A.This improvement is attributed to the smaller particle size of red mud B,which filled the micro-pores and increased the compactness of the cement stone,as well as its higher content of Na_(2)O,K_(2)O,and other free alkalis,which resulted in more obvious alkali activation,accelerating the hydration of the active minerals in the slurry.展开更多
The paper talks about the elaboration of geopolymer with two types of kaolinite clays containing muscovite. The kaolinite materials were first calcined at different temperatures, and mixed with an activator solution, ...The paper talks about the elaboration of geopolymer with two types of kaolinite clays containing muscovite. The kaolinite materials were first calcined at different temperatures, and mixed with an activator solution, called liquid precursor, at a different solid/liquid mass ratio depending on their normal consistency to produce geopolymer binders. Results show that the geopolymer products obtained from the different clays have good physichomechanical properties: their open porosity and their water absorption rate decrease while their compressive strength and their apparent density increase with the increase in calcination temperature of the clays. The density of GABD binders varies between 2.92 and 2.47 g/cm<sup>3</sup> and that of GARD binders between 1.86 and 2.16 g/cm<sup>3</sup>. Specimens in the GABD series have the best mechanical performance, ranging from 14.43 to 31.37 MPa, while those in the GARD series oscillate between 6.18 and 11.56 MPa. These properties make kaolinite materials from this region suitable for use as construction materials for adequate waterproof structures.展开更多
Lithium-ion batteries(LIBs)have greatly facilitated our daily lives since 1990s[1,2].To meet the ever-increasing demand on energy density,Li metal is seen as the ultimate anode because of its ultra-high specific capac...Lithium-ion batteries(LIBs)have greatly facilitated our daily lives since 1990s[1,2].To meet the ever-increasing demand on energy density,Li metal is seen as the ultimate anode because of its ultra-high specific capacity(3860 m Ah/g)and the lowest electrochemical potential(-3.04 V vs.the standard hydrogen electrode)[3–6].However,issues of Li metal anode,such as Li dendrite formation and large volume change during plating/stripping。展开更多
To study the thermal decomposition of Al/Zr H_(2)/PTFE with different Al particle size as well as mechanical strength and impact sensitivity under medium and low strain rates,molding-vacuum sintering was adopted to pr...To study the thermal decomposition of Al/Zr H_(2)/PTFE with different Al particle size as well as mechanical strength and impact sensitivity under medium and low strain rates,molding-vacuum sintering was adopted to prepare four groups of power materials and cylindrical specimens with different Al particle size.The active decomposition temperature of Zr H_(2) was obtained by TG-DSC,and the quasi-static mechanics/reaction characteristics as well as the impact sensitivity of the specimen were studied respectively by quasi-static compression and drop-hammer test.The results show that the yield strength of the material decreased with the increase of the Al particle size,while the compressive strength,failure strain and toughness increased first and then decreased,which reached the maximum values of 116.61 MPa,191%,and 119.9 MJ/m respectively when the Al particle size is 12-14 mm because of particle size grading.The specimens with the highest strength and toughness formed circumferential open cracks and reacted partly when pressed.Those with developmental cracks formed inside did not react.It is considered that fracture of specimens first triggered initial reaction between Al and PTFE to release an amount of heat.Then ZrH_(2) was activated and decomposed,and participated in subsequent reaction to generate Zr C.The impact sensitivity of the specimens decreased with the increase of Al particle size.展开更多
Heat-resistant poly(m-phenylene isophthalamide)(PMIA)has attracted considerable attention as a novel separator for application in lithium-ion batteries(LIBs);however,its mechanical strength and electrolyte wettability...Heat-resistant poly(m-phenylene isophthalamide)(PMIA)has attracted considerable attention as a novel separator for application in lithium-ion batteries(LIBs);however,its mechanical strength and electrolyte wettability are not ideal.Herein,a nano-silica-decorated poly(m-phenylene isophthalamide)(PMIA@SiO2)separator was fabricated with SiO2 nanoparticles uniformly attached to the pores and pore walls of the PMIA separator.The as-prepared PMIA@SiO2 separator has good mechanical strength(a 16%improvement compared with pristine PMIA)and wettability toward the electrolyte(the contact angle decreases from 34.0°to 23.1°).The PMIA@SiO2 separator also had a high ionic conductivity(0.75 mS/cm)and low interfacial electric resistance(75Ω).The assembled LiCoO2/PMIA@Si O2-liquid electrolyte/Li cell displays good cycle performance with a capacity retention of 88.1%after 50 cycles.Furthermore,the cycling performance and rate capacity rarely changed after high-temperature treatment.Therefore,the nano-silica-decorated PMIA separator is a potential candidate for application in LIBs with high safety.展开更多
This work aims at designing a set of curing pressure routes to produce laminates with various void contents. The effects of various consolidation pressures resulting in different void contents on mechanical strength o...This work aims at designing a set of curing pressure routes to produce laminates with various void contents. The effects of various consolidation pressures resulting in different void contents on mechanical strength of carbon/epoxy laminates have been examined. Characterization of the voids, in terms of void volume fraction, void distribution, size, and shape, was performed by standard test, ultrasonic inspection and metallographic analysis. The interlaminar shear strength was measured by the short-beam method. An empirical model was used to predict the strength vs porosity. The predicted strengths conform well with the experimental data and voids were found to be uniformly distributed throughout the laminate.展开更多
A new testing methodology was developed to quantitively study galvanic corrosion of AZ31B and thermoset carbon-fiber–reinforced polymer spot-joined by a friction self-piercing riveting process.Pre-defined areas of AZ...A new testing methodology was developed to quantitively study galvanic corrosion of AZ31B and thermoset carbon-fiber–reinforced polymer spot-joined by a friction self-piercing riveting process.Pre-defined areas of AZ31B in the joint were exposed in 0.1 M NaCl solution over time.Massive galvanic corrosion of AZ31B was observed as exposure time increased.The measured volume loss was converted into corrosion current that was at least 48 times greater than the corrosion current of AZ31B without galvanic coupling.Ninety percent of the mechanical joint integrity was retained for corroded F-SPR joints to 200 h and then decreased because of the massive volume loss of AZ31B。展开更多
Wood-based hydrogel with a unique anisotropic structure is an attractive soft material,but the presence of rigid crystalline cellulose in natural wood makes the hydrogel less flexible.In this study,an all-wood hydroge...Wood-based hydrogel with a unique anisotropic structure is an attractive soft material,but the presence of rigid crystalline cellulose in natural wood makes the hydrogel less flexible.In this study,an all-wood hydrogel was constructed by cross-linking cellulose fibers,polyvinyl alcohol(PVA)chains,and lignin molecules through the Hofmeister effect.The all-wood hydrogel shows a high tensile strength of 36.5 MPa and a strain up to~438%in the longitudinal direction,which is much higher than its tensile strength(~2.6 MPa)and strain(~198%)in the radial direction,respectively.The high mechanical strength of all-wood hydrogels is mainly attributed to the strong hydrogen bonding,physical entanglement,and van der Waals forces between lignin molecules,cellulose nanofibers,and PVA chains.Thanks to its excellent flexibility,good conductivity,and sensitivity,the all-wood hydrogel can accurately distinguish diverse macroscale or subtle human movements,including finger flexion,pulse,and swallowing behavior.In particular,when“An Qi”was called four times within 15 s,two variations of the pronunciation could be identified.With recyclable,biodegradable,and adjustable mechanical properties,the all-wood hydrogel is a multifunctional soft material with promising applications,such as human motion monitoring,tissue engineering,and robotics materials.展开更多
Cu, as an austenitic stable element, is added to steel in order to suppress the adverse effects of high content of C and Mn on welding. Based on C partitioning, Cu and Mn partitioning can further improve the stability...Cu, as an austenitic stable element, is added to steel in order to suppress the adverse effects of high content of C and Mn on welding. Based on C partitioning, Cu and Mn partitioning can further improve the stability of retained austenite in the intercritical annealing process. A sample of low carbon steel containing Cu was treated by the intercritical annealing, then quenching process(I&Q). Subsequently, another sample was treated by the intercritical annealing, subsequent austenitizing, then quenching and partitioning process(I&Q&P). The effects of element partitioning behavior in intercritical region on the microstructure and mechanical properties of the steel were studied. The results showed that after the I&Q process ferrite and martensite could be obtained, with C, Cu and Mn enriched in the martensite. When intercritically heated at 800 ℃, Cu and Mn were partitioned from ferrite to austenite, which was enhanced gradually as the heating time was increased. This partitioning effect was the most obvious when the sample was heated at 800 ℃ for 40 min. At the early stage of α→γ transformation, the formation of γ was controlled by the partitioning of carbon, while at the later stage, it was mainly affected by the partitioning of Cu and Mn. After the I&Q&P process, the partitioning effect of Cu and Mn element could be retained. C was assembled in retained austenite during the quenching and partitioning process. The strength and elongation of I&Q&P steel was increased by 5 305 MPa% compared with that subjected to Q&P process. The volume fraction of retained autensite was increased from 8.5% to 11.2%. Hence, the content of retained austenite could be improved significantly by Mn and Cu partitioning, which increased the elongation of steel.展开更多
The mechanics of porous catalyst paricles has been discussed and outlined. Concept of brittle fracture, statistical model of single-particle strength, and bulk crushing strength model were introduced. It is elucidated...The mechanics of porous catalyst paricles has been discussed and outlined. Concept of brittle fracture, statistical model of single-particle strength, and bulk crushing strength model were introduced. It is elucidated that the objective of catalyst mechanics research is to establish mechanical reliability model of converters using solid catalysts.展开更多
Thermal insulation is an important indicator to evaluate the construction material in cold region engineering.As we know,adding the industrial waste as lightweight aggregate or creating the pore inside the cement-base...Thermal insulation is an important indicator to evaluate the construction material in cold region engineering.As we know,adding the industrial waste as lightweight aggregate or creating the pore inside the cement-based composite could make the texture loose,and the thermal insulating capacity of the material would be improved with this texture.Using these methods,the industrial by-product and engineering waste could be cycled in an efficient way.Moreover,after service the fragmented cement composites paste could be used as aggregate in the thermal insulating concrete again.While the porous texture is not favorable for the mechanical strength and long-term durability in a cold environment.To balance the above three requirements from two opposite directions,different processing methods were applied to create the thermal insulation concrete/mortar.Firstly,the organic/inorganic lightweight aggregate,including the Expanded Polystyrene(EPS),Expanded Perlite(EP),and Ceramsite(CRMST)particles,were applied to create the Lightweight Aggregate Concrete(LWAC).As the comparative tests,the expanded Superabsorbent Polymer(SAP)hydrogel and Air-Entraining Agent(AEA)were also introduced to create the porous mortar.The above concrete/mortar was tested in the normal state and under the Freeze-Thaw cycle to explore the engineering performance in cold regions.During the experimenting process,the thermal insulation,mechanical strength,and frost resistance of these cement-based composites were investigated,and an optimal thermal insulation concrete/mortar was determined.展开更多
The biodegradation and mechanical properties of self-designed hydroxyapatite/poly-DL-lactide (HA/PDLLA) composites were investigated in vitro and in vivo. In vitro, the specimens of HA/PDLLA and unfilled PDLLA with s...The biodegradation and mechanical properties of self-designed hydroxyapatite/poly-DL-lactide (HA/PDLLA) composites were investigated in vitro and in vivo. In vitro, the specimens of HA/PDLLA and unfilled PDLLA with similar molecular weights were immersed in phosphate-buffered saline. Ageing of the various devices were monitored by measuring molecular weight, water absorption, weight loss, PH, mechanical strengths and microstructural changes. The follow-up times were 2, 4, 6, 8, 10 and 12 weeks. In vivo, a transverse transcondylar osteotomy of the distal femur was fixed with a HA/PDLLA rod (diameter, 4.5 mm; length, 30 to approximately 40 mm). The follow-up times were 3, 6 and 12 weeks. Roentgenographic, histologic, and biomechanical studies were carried out. The results show that the HA/PDLLA composites have higher mechanical strength and slower degradation than that of the unfilled PDLLA and that of all osteotomies unite within six weeks without delay. Consequently, the HA/PDLLA composites possess sufficient mechanical strength for the fixation of cancellous osteotomies. (Author abstract) 5 Refs.展开更多
基金supported by Hebei Province Higher Education Science and Technology Research Project(No.ZC2024031).
文摘The presence of toxic elements in manganese slag(MSG)poses a threat to the environment due to potential pollution.Utilizing CO_(2) curing on MS offers a promising approach to immobilize toxic substances within this material,thereby mitigating their release into the natural surroundings.This study investigates the impact of CO_(2) cured MS on various rheological parameters,including slump flow,plastic viscosity(η),and yield shear stress(τ).Additionally,it assesses flexural and compressive strengths(f_(t) and f_(cu)),drying shrinkage rates(DSR),durability indicators(chloride ion migration coefficient(CMC),carbonization depth(CD)),and the leaching behavior of heavy metal elements.Microscopic examination via scanning electron microscopy(SEM)is employed to elucidate the underlying mechanisms.The results indicate that CO_(2) curing significantly enhances the slump flow of ultra-high performance concrete(UHPC)by up to 51.2%.Moreover,it reduces UHPC’sηandτby rates ranging from 0%to 52.7%and 0%to 40.2%,respectively.The DSR exhibits a linear increase corresponding to the mass ratio of CO_(2) cured MS.Furthermore,CO_(2) curing enhances both f_(t) and f_(cu) of UHPC by up to 28.7%and 17.6%,respectively.The electrical resistance is also improved,showing an increase of up to 53.7%.The relationship between mechanical strengths and electrical resistance follows a cubic relationship.The CO_(2) cured MS demonstrates a notable decrease in the CMC and CD by rates ranging from 0%to 52.6%and 0%to 26.1%,respectively.The reductions of leached chromium(Cr)and manganese(Mn)are up to 576.3%and 1312.7%,respectively.Overall,CO_(2) curing also enhances the compactness of UHPC,thereby demonstrating its potential to improve both mechanical and durability properties.
基金supported by the National Research Foundation, Prime Minister’s Office, Singapore, under its Competitive Research Programme (CRP award number NRF-CRP22-2019-008)Medium-Sized Centre Programme (CA2DM)+1 种基金the Ministry of Education of Singapore, under its Research Centre of Excellence award to the Institute for Functional Intelligent Materials (I-FIM, Project No. EDUNC-33-18-279-V12)by the EDB Singapore, under its Space Technology Development Programme (S2219013-STDP)。
文摘Despite advancements in silicon-based anodes for high-capacity lithium-ion batteries,their widespread commercial adoption is still hindered by significant volume expansion during cycling,especially at high active mass loadings crucial for practical use.The root of these challenges lies in the mechanical instability of the material,which subsequently leads to the structural failure of the electrode.Here,we present a novel synthesis of a composite combining expanded graphite and silicon nanoparticles.This composite features a unique interlayer-bonded graphite structure,achieved through the application of a modified spark plasma sintering method.Notably,this innovative structure not only facilitates efficient ion and electron transport but also provides exceptional mechanical strength(Vickers hardness:up to658 MPa,Young's modulus:11.6 GPa).This strength effectively accommodates silicon expansion,resulting in an impressive areal capacity of 2.9 mA h cm^(-2)(736 mA h g^(-1)) and a steady cycle life(93% after 100cycles).Such outsta nding performance is paired with features appropriate for large-scale industrial production of silicon batteries,such as active mass loading of at least 3.9 mg cm^(-2),a high-tap density electrode material of 1.68 g cm^(-3)(secondary clusters:1.12 g cm^(-3)),and a production yield of up to 1 kg per day.
基金supported by the Czech Science Foundation under project no.22-21122JPartial financial support from the Ministry of Health of the Czech Republic under the grant Nr.20-08-00150+2 种基金partial financial support from the Charles University Grant Agency under project number 389422partial financial support from the Science Grant Agency of the Slovak Republic through project No.1/0153/21faculty specific research project FSI-S-23-8340.
文摘This work explored possibilities of biodegradable magnesium alloy Mg-3Y preparation by two modern powder metallurgy techniques–spark plasma sintering(SPS)and selective laser melting(SLM).The powder material was consolidated by both methods utilising optimised parameters,which led to very low porosity(∼0.3%)in the SLM material and unmeasurably low porosity in the SPS material.The main aim of the study was the thorough microstructure characterisation and interrelation between the microstructure and the functional properties,such as mechanical strength,deformability,and corrosion resistance.Both materials showed comparable strength of∼110 MPa in tension and compression and relatively good deformability of∼9%and∼21%for the SLM and SPS materials,respectively.The corrosion resistance of the SPS material in 0.1 M NaCl solution was superior to the SLM one and comparable to the conventional extruded material.The digital image correlation during loading and the cross-section analysis of the corrosion layers revealed that the residual porosity and large strained grains have the dominant negative effect on the functional properties of the SLM material.On the other hand,one of the primary outcomes of this study is that the SPS consolidation method is very effective in the preparation of the W3 biodegradable alloy,resulting in material with convenient mechanical and degradation properties that might find practical applications.
基金The authors gratefully acknowledge financial support from the National Natural Science Foundation of China(52103090)the Natural Science Foundation of Guangdong Province(2022A1515011780)Autonomous deployment project of China National Key Laboratory of Materials for Integrated Circuits(NKLJC-Z2023-B03).
文摘The remarkable properties of carbon nanotubes(CNTs)have led to promising applications in the field of electromagnetic inter-ference(EMI)shielding.However,for macroscopic CNT assemblies,such as CNT film,achieving high electrical and mechanical properties remains challenging,which heavily depends on the tube-tube interac-tions of CNTs.Herein,we develop a novel strategy based on metal-organic decomposition(MOD)to fabricate a flexible silver-carbon nanotube(Ag-CNT)film.The Ag particles are introduced in situ into the CNT film through annealing of MOD,leading to enhanced tube-tube interactions.As a result,the electrical conductivity of Ag-CNT film is up to 6.82×10^(5) S m^(-1),and the EMI shielding effectiveness of Ag-CNT film with a thickness of~7.8μm exceeds 66 dB in the ultra-broad frequency range(3-40 GHz).The tensile strength and Young’s modulus of Ag-CNT film increase from 30.09±3.14 to 76.06±6.20 MPa(~253%)and from 1.12±0.33 to 8.90±0.97 GPa(~795%),respectively.Moreover,the Ag-CNT film exhibits excellent near-field shield-ing performance,which can effectively block wireless transmission.This innovative approach provides an effective route to further apply macroscopic CNT assemblies to future portable and wearable electronic devices.
基金Fouded by the National Natural Science Foundation of China(No.51175308)the National Science and Technology Major Project of China(No.2012ZX04010032)。
文摘Because inferior mechanical strength of granite polymer composite(GPC)has become the main drawback limiting its application and popularization,Mo fibers were added into(GPC)to improve its mechanical strength.Mechanical properties of matrix materials with different mass ratio of resin and stabilizer(MRRS)were investigated systematically.The influences of MRRS on interface bonding strength of Mo fiber-matrix,wettability and mechanical strength of GPC were discussed,respectively,and the theoretical calculation result of MRRS k was obtained,with the optimal value of k=4.When k=4,tensile strength,tensile strain and fracture stress of the cured resin achieve the maximum values.But for k=7,the corresponding values reach the minimum.With the increase of MRRS k,surface free energy of the cured resin first increases and then decreases,while contact angles between Mo sample and matrix have displayed the opposite trend.Wettability of resin to Mo fiber is the best at k=4.Pulling load of Mo fiber and interface bonding strength appear the maximum at k=4,followed by k=5,k=3 the third,and k=7 the minimum.When k=4,mechanical properties of Mo fiber-reinforced GPC are optimal,which is consistent with the result of theoretical calculation.This study is of great significance to get better component formulas of Mo fiber reinforced GPC and to improve its application in machine tools.
文摘The mining process involves drilling and excavation, resulting in the production of waste rock and tailings. The waste materials are then removed and stored in designated areas. This study aims to evaluate the mechanical strength and the environmental and economic impact of using Coltan Mining Waste (CMW) as a substitute for aggregates in concrete and mortar production. To achieve this, the CMW needs to be characterised. The Dreux Gorisse method was primarily used to produce concrete with a strength of 20 MPa at 28 days. The mortars, on the other hand, were formulated according to the NF P 18-452 standard. The environmental impact of using CMW as substitutes for natural aggregates in the production of concrete and mortar was analysed using SimaPro software. The results showed that mortars and concrete made with CMW have comparable compressive strengths to the reference mortar and concrete;reduce the negative impact on ecosystem quality, human health, resources, and climate change. It has also been shown that the substitution of aggregates by CMW reduces the cost of concrete and mortar as a function of the distance from the aggregate footprint.
基金supported by Czech Science Foundation under project no. 22-21122 JPartial financial support from the Ministry of Health of the Czech Republic under the grant Nr.20-08-0015A+1 种基金partial financial support from the Charles University Grant Agency under project numbers 389422 and 1172120, respectivelypartial financial support from the Ministry of Transport and Construction of the Slovak Republic,OPII,grant No. ITMS:313011AFG4, co-financed by ERDF。
文摘This work investigated the effect of sole yttrium and neodymium alloying on the microstructure formation during severe plastic deformation by equal channel angular pressing(ECAP) and an impact on the mechanical strength and corrosion resistance of binary Mg-3Y and Mg-3Nd alloys.The results are compared with a ternary Mg-4Y-3Nd alloy,which represents a simplified version of the commercially successful WE43 alloy.The extensive study comprises a thorough microstructural analysis performed by scanning and transmission electron microscopy,including electron backscatter diffraction and texture analysis performed by X-ray diffraction.It is shown that the presence of Nd primarily caused precipitation during the processing of the Mg-3Nd alloy,while Y remained dissolved in the magnesium matrix in the Mg-3Y alloy.This difference resulted in a significantly smaller average grain size in the Mg-3Y alloy(~0.77 nm) than in the Mg-3Nd alloy(~1.3 μm) after the final step of the processing and formation of a slightly different texture.Consequently,the composition and the processing affected the mechanical and corrosion properties of the investigated materials,measured by compression deformation tests,microhardness measurement,and electrochemical impedance spectroscopy.This study shows that the ECAP-processed W3 sample exhibits a surprisingly good combination of ultrafine-grain structure,weak crystallographic texture,high strength,and high corrosion resistance compared with the other investigated samples.These attributes make this material very interesting for utilisation in the industry and/or medicine.
基金The research presented in this paper was supported by National Natural Science Foundation of China(Grant No.52272031)the Fundamental Research Funds for the Central Universities,China University of Geosciences(Wuhan),and the Opening Fund of Guangxi Key Laboratory of New Energy and Building Energy Saving(Grant No.19-J-22-2)+3 种基金Key Research and Development Program of Hubei Province(Grant No.2020BAB065)Key Research and Development Program of Jiangxi Province(Grant No.20201BBG71011)Fundamental Research Funds for the Central Universities,CHD(Grant No.300102211506)Opening Fund of Key Laboratory of Advanced Building Materials of Anhui Province(Grant No.JZCL001KF).
文摘Montmorillonite and clinoptilolite zeolite were used as representative materials to prepare calcined clay-cement binary cementitious materials in order to study the effect of calcination treatment on the activation of clay minerals and the activity difference between layered and framed clays in this research.The influence of different calcined clay content(2%,4%,6%,8%,10%)on the fluidity,compressive strength,microstructure,phase change,and hydration heat of cement-based materials were analyzed.The calcined clay improves the fluidity of cement-based materials as compared with the uncalcined group.The addition of calcined montmorillonite(CMT)improves the development of mechanical strength,and the optimal compressive strength reaches 85 MPa at 28 days with 8%CMT.However,the activity of calcined clinoptilolite zeolite(CZL)is weak with few reaction sites,which slightly reduced the mechanical strength as compared to the blank sample.The addition of CMT changes the microscopic morphology of hydration products such as C-S-H and C-A-H,leading to the formation and transformation of ettringite in the early stage.It promotes the gradual polymerization of Si-O bonds into Si-O-Si bonds simultaneously,which accelerates the early hydration process.However,CZL acts mainly as a filling function in the cementitious system.In brief,CMT as an admixture can improve the mechanical properties of cement,but CZL has little effect.This work provides a guideline for the applications of calcined clay in cement,considering the influence of clay type on workability and mechanical strength.
基金the Guangxi Science and Technology Program(Guike AD21220052,AD22035126 and AB22035064)National Natural Science Foundation of China(52062009)Guangxi Key Laboratory of New Energy and Building Energy Saving(Guikeneng 22-J-21-19).
文摘The aim of this study is to enhance the value and utilization of red mud generated in the Bayer process by preparing composite cement mortars.The effects of two different types of Bayer red mud with varying physical and chemical characteristics on the fluidity,mechanical strength,mineral composition,and microstructure of the composite cement mortar were systematically evaluated.The results showed that the optimal addition of red mud A was 10 wt%,while it was 20 wt% for red mud B.The mechanical properties of the composite cement mortar met the standards for P·O42.5 cement.Furthermore,the composite mortar with the addition of red mud B showed higher flexural and compressive strengths compared to the composite mortar with red mud A.This improvement is attributed to the smaller particle size of red mud B,which filled the micro-pores and increased the compactness of the cement stone,as well as its higher content of Na_(2)O,K_(2)O,and other free alkalis,which resulted in more obvious alkali activation,accelerating the hydration of the active minerals in the slurry.
文摘The paper talks about the elaboration of geopolymer with two types of kaolinite clays containing muscovite. The kaolinite materials were first calcined at different temperatures, and mixed with an activator solution, called liquid precursor, at a different solid/liquid mass ratio depending on their normal consistency to produce geopolymer binders. Results show that the geopolymer products obtained from the different clays have good physichomechanical properties: their open porosity and their water absorption rate decrease while their compressive strength and their apparent density increase with the increase in calcination temperature of the clays. The density of GABD binders varies between 2.92 and 2.47 g/cm<sup>3</sup> and that of GARD binders between 1.86 and 2.16 g/cm<sup>3</sup>. Specimens in the GABD series have the best mechanical performance, ranging from 14.43 to 31.37 MPa, while those in the GARD series oscillate between 6.18 and 11.56 MPa. These properties make kaolinite materials from this region suitable for use as construction materials for adequate waterproof structures.
基金financial support by the National Natural Science Foundation of China(No.51802224)“Shanghai Rising-Star Program”(19QA1409300)Shanghai Aerospace Science and Technology Innovation Fundation(SISP2018)。
文摘Lithium-ion batteries(LIBs)have greatly facilitated our daily lives since 1990s[1,2].To meet the ever-increasing demand on energy density,Li metal is seen as the ultimate anode because of its ultra-high specific capacity(3860 m Ah/g)and the lowest electrochemical potential(-3.04 V vs.the standard hydrogen electrode)[3–6].However,issues of Li metal anode,such as Li dendrite formation and large volume change during plating/stripping。
基金financial support from the National Natural Science Foundation of China(General Program.Grant No.51673213)the National Natural Science Foundation of China(Youth Science Foundation.Grant No.51803235)。
文摘To study the thermal decomposition of Al/Zr H_(2)/PTFE with different Al particle size as well as mechanical strength and impact sensitivity under medium and low strain rates,molding-vacuum sintering was adopted to prepare four groups of power materials and cylindrical specimens with different Al particle size.The active decomposition temperature of Zr H_(2) was obtained by TG-DSC,and the quasi-static mechanics/reaction characteristics as well as the impact sensitivity of the specimen were studied respectively by quasi-static compression and drop-hammer test.The results show that the yield strength of the material decreased with the increase of the Al particle size,while the compressive strength,failure strain and toughness increased first and then decreased,which reached the maximum values of 116.61 MPa,191%,and 119.9 MJ/m respectively when the Al particle size is 12-14 mm because of particle size grading.The specimens with the highest strength and toughness formed circumferential open cracks and reacted partly when pressed.Those with developmental cracks formed inside did not react.It is considered that fracture of specimens first triggered initial reaction between Al and PTFE to release an amount of heat.Then ZrH_(2) was activated and decomposed,and participated in subsequent reaction to generate Zr C.The impact sensitivity of the specimens decreased with the increase of Al particle size.
基金supported by National Science and Technology Major Project(No.2016ZX02025-004-006)Science and Technology Project of China National Off shore Oil Corporation(No.CNOOC-KJ 135 ZDXM 35 TJY 009-2017).
文摘Heat-resistant poly(m-phenylene isophthalamide)(PMIA)has attracted considerable attention as a novel separator for application in lithium-ion batteries(LIBs);however,its mechanical strength and electrolyte wettability are not ideal.Herein,a nano-silica-decorated poly(m-phenylene isophthalamide)(PMIA@SiO2)separator was fabricated with SiO2 nanoparticles uniformly attached to the pores and pore walls of the PMIA separator.The as-prepared PMIA@SiO2 separator has good mechanical strength(a 16%improvement compared with pristine PMIA)and wettability toward the electrolyte(the contact angle decreases from 34.0°to 23.1°).The PMIA@SiO2 separator also had a high ionic conductivity(0.75 mS/cm)and low interfacial electric resistance(75Ω).The assembled LiCoO2/PMIA@Si O2-liquid electrolyte/Li cell displays good cycle performance with a capacity retention of 88.1%after 50 cycles.Furthermore,the cycling performance and rate capacity rarely changed after high-temperature treatment.Therefore,the nano-silica-decorated PMIA separator is a potential candidate for application in LIBs with high safety.
文摘This work aims at designing a set of curing pressure routes to produce laminates with various void contents. The effects of various consolidation pressures resulting in different void contents on mechanical strength of carbon/epoxy laminates have been examined. Characterization of the voids, in terms of void volume fraction, void distribution, size, and shape, was performed by standard test, ultrasonic inspection and metallographic analysis. The interlaminar shear strength was measured by the short-beam method. An empirical model was used to predict the strength vs porosity. The predicted strengths conform well with the experimental data and voids were found to be uniformly distributed throughout the laminate.
基金financially sponsored by the US Department Energy Vehicle Technologies Office, as part of the Joining Core Programmanaged by UT-Battelle LLC for the US Department of Energy under Contract DE-AC05-00OR22725。
文摘A new testing methodology was developed to quantitively study galvanic corrosion of AZ31B and thermoset carbon-fiber–reinforced polymer spot-joined by a friction self-piercing riveting process.Pre-defined areas of AZ31B in the joint were exposed in 0.1 M NaCl solution over time.Massive galvanic corrosion of AZ31B was observed as exposure time increased.The measured volume loss was converted into corrosion current that was at least 48 times greater than the corrosion current of AZ31B without galvanic coupling.Ninety percent of the mechanical joint integrity was retained for corroded F-SPR joints to 200 h and then decreased because of the massive volume loss of AZ31B。
基金The authors gratefully acknowledge the financial support from the National Natural Science Foundation of China,China(Nos.21978248,21676223)the Natural Science Foundation of Fujian Province of China(No.2019J06005)+1 种基金Guangdong Provincial Key Research and Development Program(No.2020B0101070001)Open access funding provided by Shanghai Jiao Tong University
文摘Wood-based hydrogel with a unique anisotropic structure is an attractive soft material,but the presence of rigid crystalline cellulose in natural wood makes the hydrogel less flexible.In this study,an all-wood hydrogel was constructed by cross-linking cellulose fibers,polyvinyl alcohol(PVA)chains,and lignin molecules through the Hofmeister effect.The all-wood hydrogel shows a high tensile strength of 36.5 MPa and a strain up to~438%in the longitudinal direction,which is much higher than its tensile strength(~2.6 MPa)and strain(~198%)in the radial direction,respectively.The high mechanical strength of all-wood hydrogels is mainly attributed to the strong hydrogen bonding,physical entanglement,and van der Waals forces between lignin molecules,cellulose nanofibers,and PVA chains.Thanks to its excellent flexibility,good conductivity,and sensitivity,the all-wood hydrogel can accurately distinguish diverse macroscale or subtle human movements,including finger flexion,pulse,and swallowing behavior.In particular,when“An Qi”was called four times within 15 s,two variations of the pronunciation could be identified.With recyclable,biodegradable,and adjustable mechanical properties,the all-wood hydrogel is a multifunctional soft material with promising applications,such as human motion monitoring,tissue engineering,and robotics materials.
基金Funded by National Natural Science Foundation of China(Nos.51574107,51304186)Natural Science Foundation of Hebei Province(Nos.E2016209048,E2017209048)Tangshan High Performance Metal and Composite Materials Science and Technical Innovation Team(No.15130202C)
文摘Cu, as an austenitic stable element, is added to steel in order to suppress the adverse effects of high content of C and Mn on welding. Based on C partitioning, Cu and Mn partitioning can further improve the stability of retained austenite in the intercritical annealing process. A sample of low carbon steel containing Cu was treated by the intercritical annealing, then quenching process(I&Q). Subsequently, another sample was treated by the intercritical annealing, subsequent austenitizing, then quenching and partitioning process(I&Q&P). The effects of element partitioning behavior in intercritical region on the microstructure and mechanical properties of the steel were studied. The results showed that after the I&Q process ferrite and martensite could be obtained, with C, Cu and Mn enriched in the martensite. When intercritically heated at 800 ℃, Cu and Mn were partitioned from ferrite to austenite, which was enhanced gradually as the heating time was increased. This partitioning effect was the most obvious when the sample was heated at 800 ℃ for 40 min. At the early stage of α→γ transformation, the formation of γ was controlled by the partitioning of carbon, while at the later stage, it was mainly affected by the partitioning of Cu and Mn. After the I&Q&P process, the partitioning effect of Cu and Mn element could be retained. C was assembled in retained austenite during the quenching and partitioning process. The strength and elongation of I&Q&P steel was increased by 5 305 MPa% compared with that subjected to Q&P process. The volume fraction of retained autensite was increased from 8.5% to 11.2%. Hence, the content of retained austenite could be improved significantly by Mn and Cu partitioning, which increased the elongation of steel.
文摘The mechanics of porous catalyst paricles has been discussed and outlined. Concept of brittle fracture, statistical model of single-particle strength, and bulk crushing strength model were introduced. It is elucidated that the objective of catalyst mechanics research is to establish mechanical reliability model of converters using solid catalysts.
基金The research project was supported by the Natural Science Foundation of China(Grant Nos.51972209,41801033,41801043)Young doctor Foundation of Education Department of Gansu Province(2021QB-039)+1 种基金Basic Research Innovation Group of Gansu Province(20JR5RA478)Industrial Support Program of Higher Education of Gansu Province(2020C−40).
文摘Thermal insulation is an important indicator to evaluate the construction material in cold region engineering.As we know,adding the industrial waste as lightweight aggregate or creating the pore inside the cement-based composite could make the texture loose,and the thermal insulating capacity of the material would be improved with this texture.Using these methods,the industrial by-product and engineering waste could be cycled in an efficient way.Moreover,after service the fragmented cement composites paste could be used as aggregate in the thermal insulating concrete again.While the porous texture is not favorable for the mechanical strength and long-term durability in a cold environment.To balance the above three requirements from two opposite directions,different processing methods were applied to create the thermal insulation concrete/mortar.Firstly,the organic/inorganic lightweight aggregate,including the Expanded Polystyrene(EPS),Expanded Perlite(EP),and Ceramsite(CRMST)particles,were applied to create the Lightweight Aggregate Concrete(LWAC).As the comparative tests,the expanded Superabsorbent Polymer(SAP)hydrogel and Air-Entraining Agent(AEA)were also introduced to create the porous mortar.The above concrete/mortar was tested in the normal state and under the Freeze-Thaw cycle to explore the engineering performance in cold regions.During the experimenting process,the thermal insulation,mechanical strength,and frost resistance of these cement-based composites were investigated,and an optimal thermal insulation concrete/mortar was determined.
文摘The biodegradation and mechanical properties of self-designed hydroxyapatite/poly-DL-lactide (HA/PDLLA) composites were investigated in vitro and in vivo. In vitro, the specimens of HA/PDLLA and unfilled PDLLA with similar molecular weights were immersed in phosphate-buffered saline. Ageing of the various devices were monitored by measuring molecular weight, water absorption, weight loss, PH, mechanical strengths and microstructural changes. The follow-up times were 2, 4, 6, 8, 10 and 12 weeks. In vivo, a transverse transcondylar osteotomy of the distal femur was fixed with a HA/PDLLA rod (diameter, 4.5 mm; length, 30 to approximately 40 mm). The follow-up times were 3, 6 and 12 weeks. Roentgenographic, histologic, and biomechanical studies were carried out. The results show that the HA/PDLLA composites have higher mechanical strength and slower degradation than that of the unfilled PDLLA and that of all osteotomies unite within six weeks without delay. Consequently, the HA/PDLLA composites possess sufficient mechanical strength for the fixation of cancellous osteotomies. (Author abstract) 5 Refs.