The effect of fractional thermoelasticity on a two-dimensional problem of a mode I crack in a rotating fiber-reinforced thermoelastic medium

This article is concerned with the effect of rotation on the general model of the equations of the generalized thermoe- lasticity for a homogeneous isotropic elastic half-space solid, whose surface is subjected to a Mode-I crack problem. The fractional order theory of thermoelasticity is used to obtain the analytical solutions for displacement components, force stresses, and temperature. The boundary of the crack is subjected to a prescribed stress distribution and temperature. The normal mode analysis technique is used to solve the resulting non-dimensional coupled governing equations of the problem. The variations of the considered variables with the horizontal distance are illustrated graphically. Some particular cases are also discussed in the context of the problem. Effects of the fractional parameter, reinforcement, and rotation on the varia- tions of different field quantities inside the elastic medium are analyzed graphically. Comparisons are made between the results in the presence and those in the absence of fiber-reinforcing, rotating and fractional parameters.

Microstructure and Wear Performance of High Volume Fraction Carbide M_7C_3 Reinforced Fe-based Composite Coating Fabricated by Plasma Transferred Arc Welding

The fabrication of high volume fraction （HVF） M7C3 （M=Cr, Fe） reinforced Fe-based composite coating on ASTM A36 steel plate using plasma transferred arc （PTA） welding was studied. The results showed that the volume fraction of carbide M7C3 was more than sixty percent, and the relative wear resistance of the coating tested on a block-on-ring dry sliding tester at constant load （100 N） and variable loads （from 100 to 300 N） respectively was about 9 and 14 times higher than that of non-reinforced a-Fe coating. In addition, under constant load condition the friction coefficients （FCs） of two coatings increased first and then decreased with increasing sliding distance. However, under variable loads condition the FCs of non-reinforced a-Fe based coating increased gradually, while that of HVF MTC3 reinforced coating decreased as the load exceeded 220 N. The worn surface of non-reinforced a-Fe based coating was easily deformed and grooved, while that of the HVF M7C3 reinforced coating was difficult to be deformed and grooved.

Heat treatment and granule medium internal highpressure forming of AA6061 tube

The new forming process of AA6061 alloy tube, including solution treatment, granule medium internal high-pressure forming and aging treatment, was developed. The AA6061 alloy tube via heat treatment satisfied the forming requirement, and the granule medium internal high pressure forming method for AA6061 alloy tube was also realized by using convenient implementation with low requirement of equipment and flexible design of product. At a solution temperature of 560℃ and time of 120 min, the elongation of the AA6061 extruded tube increases by 300% and the strength and the hardness dramatically decrease too. Therefore, the AA6061 alloy tube meets the requirement of internal high-pressure forming because of the improvement of formability. The experiments shows that the strength and hardness of AA6061 alloy workpiece recover to that of the as-received alloy at an aging temperature of 180℃ and time of 360 min, and the strength of AA6061 alloy workpiece is equal to the base alloy. The typical parts of convex ring tube, stepped shaft tube and hexagonal tube were successfully produced in lab by using the present forming method. The forming tests show that the maximum expansion ratio(MER) of the AA6061 extruded tube increases by 25.5% and the material properties of formed AA6061 alloy tube reached the performance of as-received alloy.

Carboniferous Highly Fractionated I-type Granites from the Kalamaili Fault Zone, Eastern Xinjiang, NW China: Petrogenesis and Tectonic Implications

Carboniferous magmatism is one of the most important tectonothermal events in the Central Asian Orogenic Belt(CAOB). However, the final closure time of the Kalamaili Ocean between East Junggar and Harlik Mountain is still debated. Early Carboniferous(332 Ma) and late Carboniferous(307-298 Ma) granitic magmatism from Kalamaili fault zone have been recognized by LA-ICP-MS zircon U-Pb dating. They are both metaluminous highly fractionated I-type and belong to the high-K calc-alkaline. The granitoids for early Carboniferous have zircon εHf(t) values of-5.1 to +8.5 with Hf model ages(TDM2) of 1.78-0.83 Ga, suggesting a mixed magma source of juvenile material with old continental crust. Furthermore, those for late Carboniferous have much younger heterogeneous zircon εHf(t) values(+5.1 to +13.6) with Hf model ages(TDM2=1.03-0.45 Ga) that are also indicative of juvenile components with a small involvement of old continental crust. Based on whole-rock geochemical and zircon isotopic features, these high-K granitoids were derived from melting of heterogeneous crustal sources or through mixing of old continental crust with juvenile components and minor AFC(assimilation and fractional crystallization). The juvenile components probably originated from underplated basaltic magmas in response to asthenospheric upwelling. These Carboniferous highly fractionated granites in the Kalamaili fault zone were probably emplaced in a post-collisional extensional setting and suggested vertical continental crustal growth in the southern CAOB, which is the same or like most granitoids in CAOB. This study provides new evidence for determining the post-accretionary evolution of the southern CAOB. In combination with data from other granitoids in these two terranes, the Early Carboniferous Heiguniangshan pluton represents the initial record of post-collisional environment, suggesting that the final collision between the East Junggar and Harlik Mountain might have occurred before 332 Ma.

Effects of Combined Instantaneous High-Pressure and Medium Temperature on Peroxidase Activity in Wax Gourd Juices

Based on the instantaneous pressurization and depressurization produced by high pressure single pole cylinder pump and valve, the effects of the continuous processing on the peroxidase (POD) activity in wax gourd juices were investigated. Results showed that the processing factors such as pressure, temperature, pH and processing time are important to the POD activity. POD in crude juices could be inactivated apparently above 50 MPa(pH 4.6, 35℃, 4 min), and activated at 20 MPa ( P < 0.01). Its remarkable inactivation could also be observed at 45 and 55℃ (20 MPa, pH 4.6, 4 min), and the evident activation appears at the material temperature 35℃ ( P < 0.01). The pH 3.0 could destroy POD almost completely (20 MPa, 35℃, 4 min), while pH 6.0 could not influence apparently the POD activity in crude juices( P > 0.05). In addition, the rules of POD activity along with the treatment time are variational under different processing pressures. The higher the treating pressure is, the shorter the processing time is needed to inactivate POD.

Vacuum Infusion Molding Process Part 1:VIMP Based on a High-Permeable Medium

The visualization experiments were carried out to investigate the permeability of the high permeable medium (HPM) and the roles of the peel ply and the HPM in the mold filling.The influence of process parameters on mold filling is discussed.Furthermore,the whole vacuum infusion molding process (VIMP) procedure is introduced in detail taking the manufacture of a model boat for example.

Monitoring of Karst Rocky Desertification Control Projects Based on Remote Sensing Images with Medium and High Spatial Resolution——A Case Study of Disi River Basin in Puan County

[ Objective] The study aimed to improve methods of monitoring Karst Rocky Desertification （KRD） control projects and increase the working efficiency. [Method] Based on remote sensing images with medium and high spatial resolution, KRD control projects in Disi River basin in Puan County were monitored, that is, information of the project construction in the study area was extracted using supervised classification and hu- man-computer interactive interpretation, and the monitoring results were testified with the aid of GPS. [Result] It was feasible to monitor KRD con- trol projects in Disi River basin based on remote sensing images with medium and high resolution, and the monitoring accuracy was satisfactory, reaching above 80% or 90%, so the method is worthy of popularizing. [ Conclusion] Remote sensing images with medium and high resolution can be used to monitor other KRD control Droiects.

Development of a Medium Voltage, High Power, High Frequency Four-Port Solid State Transformer

The power and voltage levels of renewable energy resources is growing with the evolution of the power electronics and switching module technologies.For that,the need for the development of a compact and highly efficient solid-state transformer is becoming a critical task in-order to integrate the current AC grid with the new renewable energy systems.The objective of this paper is to present the design,implementation,and testing of a compact multi-port solid-state transformer for microgrid integration applications.The proposed system has a four-port transformer and four converters connected to the ports.The transformer has four windings integrated on a single common core.Thus,it can integrate different renewable energy resources and energy storage systems.Each port has a rated power of 25 kW,and the switching frequency is pushed to 50 k Hz.The ports are chosen to represent a realistic industrial microgrid model consisting of grid,energy storage system,photovoltaic system,and load.The grid port is designed to operate at 4.16 k VAC corresponding to 7.2 kV DC bus voltage,while the other three ports operate at 500 VDC.Moreover,the grid,energy storage and photovoltaic ports are active ports with dual active bridge topologies,while the load port is a passive port with full bridge rectifier one.The proposed design is first validated with simulation results,and then the proposed transformer is implemented and tested.Experimental results show that the designed system is suitable for 4.16 k VAC medium voltage grid integration.

Flow Characteristics of Crude Oil with High Water Fraction during Non-heating Gathering and Transportation

In order to ensure the safety of the non-heating gathering and transportation processes for high water fraction crude oil,the effect of temperature,water fraction,and flow rate on the flow characteristics of crude oil with high water fraction was studied in a flow experimental system of the X Oilfield.Four distinct flow patterns were identified by the photographic and local sampling techniques.Especially,three new flow patterns were found to occur below the pour point of crude oil,including EW/O&W stratified flow with gel deposition,EW/O&W intermittent flow with gel deposition,and water single-phase flow with gel deposition.Moreover,two characteristic temperatures,at which the change rate of pressure drop had changed obviously,were found during the change of pressure drop.The characteristic temperature of the first congestion of gel deposition in the pipeline was determined to be the safe temperature for the non-heating gathering and transportation of high water cut crude oil,while the pressure drop reached the peak at this temperature.An empirical formula for the safe temperature was established for oil-water flow with high water fraction/low fluid production rate.The results can serve as a guide for the safe operation of the non-heating gathering and transportation of crude oil in high water fraction oilfields.

2D and 3D milled surface roughness of high volume fraction Si Cp/Al composites

This paper presents a study on surface roughness generated by high speed milling of high volume fraction(65%) silicon carbide particlereinforced aluminum matrix(Si Cp/Al) composites.Typical 2D(Raand Rz) and 3D(Saand Sq) surface roughness parameters were selected to evaluate the influence of the milling parameters on the surface quality in comparison with aluminum alloy.The 3D topography of the milled surface was studied as well.The results indicate that 3D parameters(Saand Sq) are more capable to describe the influence of the milling parameters on the surface quality,and among them Sqis preferable due to its good sensitivity.Sqdecreases with milling speed and increases with feed rate.The influence of axial depth of cut(ADOC) is negligible.

Medium Optimization for Improved Ethanol Production in Very High Gravity Fermentation

最佳的媒介(300 g 螆铧 ? 髧 ?? 颼賥??? 旤？？

Effects of Combined Instantaneous High-Pressure and MediumTemperature on the Retention of Total Vitamin Cin Wax Gourd Juices

Based on the instantaneous high-pressure(IHP)produced by high-pressure single pole-cylinder pump, the effects of combining this pressure with medium temperature on the retention of total vitamin C(Vc)in wax gourd juices were investigated under 20 - 80 MPa, 35 - 58℃, pH 3. 0 - 6. 0 and processing time 0-8 min. Results showed that the loss of Vc increased with elevated processing temperatures(50 MPa, 4 min). When the temperature of raw juices was 35℃, the retention of total Vc was higher under 40 - 60 MPa than that under the pressure < 40 MPa or > 60 MPa, and it was up to 94%(4 min). The retention of total Vc decreases slowly within 6 min, but rapidly after 6 min. The pH can also influence the retention of total Vc, and this retention can come to a highest point at pH 6.0.

Effect of Boron on Delayed Fracture Resistance of Medium-Carbon High Strength Spring Steel

The delayed fracture behavior of medium carbon high strength spring steel containing different amounts of boron （0. 000 5%, 0. 001 6 %） was studied using sustained load delayed fracture test. The results show that delayed fracture resistance of boron containing steels is higher than that of conventional steel 60Si2MnA at the same strength level and it increases with the increase of boron eontent from 0. 000 5% to 0. 001 6%. The delayed fracture mode is mainly intergranular in the boron containing steels tempered at 350℃, which indicates that the addition of boron does not change the fracture character. However, the increase of boron content enlarges the size of the crack initia tion area. Further study of phase analysis indicates that most boron is in solid solution, and only a very small quantity of boron is in the M3 （C, B） phase.

Mold Filling Analysis in Vacuum Infusion Molding Process Based on a High-Permeable Medium

The objective of this paper is to understand the flow mechanism through visualization experiments and discuss theinfluence of process parameters on mold filling process. A 2D leakage flow model is developed to simulate the moldingprocess, and the simulation results show good agreement with experiments.

Effect of RE-Modifier on Microstructure and Mechanical Property of High-Carbon Medium-Manganese Steel

The effect of RE-modifier on the microstructure and mechanical properties of high carbon-medium manganese steel has been investigated in present work.The results showed that the RE-modifier can refine the crystalline grain of high-carbon medium-manganese steel.The shape and distribution of carbides are improved and the columnar grains and phosphide in grain boundary are eliminated.Consequently,the impact toughness of the steel is increased by more than one time,compared with no addition of RE-modifier.

Multilevel Current Source Converters for High Power Medium Voltage Applications

In medium voltage high power applications,multi-level current source converters(CSCs)are good candidate to increase system power region,reliability,and the quality of output waveforms.Compared with widely researched voltage source multi-level converters(MLCs),the current source MLCs have the advantages of inherent short-circuit protection,high power capability and high quality of output current waveforms.The main features of MLCs include reduced harmonics,lower switching frequency and reduced current stress on each device which is a particularly important for high power application with low voltage and high current requirements.This paper conducts a general review of the current research about MLCs in higher power medium voltage application.The different types of parallel structure based MLCs and the modulation methodologies will be introduced and compared.Specifically,the circuit analysis of the common-mode(CM)loop for parallel structures will be conducted,the common-mode voltage(CMV)and circulating current suppression methods developed on the base of multilevel modulations will be addressed.

Maximum Power Point Tracking With Fractional Order High Pass Filter for Proton Exchange Membrane Fuel Cell

Proton exchange membrane fuel cell(PEMFC) is widely recognized as a potentially renewable and green energy source based on hydrogen. Maximum power point tracking(MPPT) is one of the most important working conditions to be considered. In order to improve the performance such as convergence and robustness under disturbance and uncertainty,a fractional order high pass filter(FOHPF) is applied for the MPPT controller design based on the traditional extremum seeking control(ESC). The controller is designed with integerorder integrator(IO-I) and low pass filter(IO-LPF) together with fractional order high pass filter(FOHPF), by substituting the normal HPF in the original ESC system. With this FOHPF ESC,better convergence and smoother performance are achieved while maintaining the robust specifications. First, tracking stability is discussed under the commensurate-order condition. Then,simulation results are included to validate the proposed new FOHPF ESC scheme under disturbance. Finally, comparison results between FOHPF ESC and the traditional ESC method are also provided.

ANALYSES OF ERRORS IN MEDIUM-TERM NUMERICAL FORECAST PRODUCTS FOR THE SUBTROPICAL HIGH 1998

By statistic and dynamic analyses, we have come to the following conclusions: (1) The ECMWF medium-term numerical forecast can forecast medium-term activity of subtropical high, and the accuracy rate of forecast cannot have large improvement by translational corrections. (2) The important cause for the ECMWF medium-term numerical forecast to have errors in 1998 is that the astronomical tide is not included in the model. (3) Two indexes are found from which it can be judged that ECMWF medium-term numerical forecast will have errors if the astronomical tide is ignored in the model : ① When the 54.7?line under the moon of the nodical month astronomical singularities coincides with the trough-line of the subtropical jet flow from 50癊 to 150癊 on the 500 hPa level at 2000 L.T. of the same day, and is approximately vertical (α>60? with the isotherm, then the day 0 2 days after the appearance of the nodical month astronomical singularities is defined as the initial day. Then in three successive days after the initial day, ECMWF medium-term numerical forecast of the northern latitude of the 588 line at 120 癊 will have continuous errors as large as two latitudes (7/9). Otherwise, it won’t have continuous errors (13/13). ② Otherwise, if the 54.7 ?line is in the range of a low pressure between two high pressures, then there is a dispersive error on the day of the nodical month astronomical singularities (5/7). There is not any error (6/6) otherwise.

Heterogeneous geological conditions and differential enrichment of medium and high maturity continental shale oil in China

Based on the comparison of basic geological conditions and enrichment characteristics of shale oil plays, the heterogeneity of source and reservoir conditions and differential enrichment of medium-high maturity continental shale oil plays in China have been confirmed.(1) Compared with the homogeneous geological settings and wide distribution of marine shale oil strata in North America, the continental medium and high maturity shale oil plays in China are significantly different in geological conditions generally;continental multi-cyclic tectonic evolution forms multiple types of lake basins in multi-stages, providing sites for large-scale development of continental shale oil, and giving rise to large scale high-quality source rocks, multiple types of reservoirs, and diverse source-reservoir combinations with significant heterogeneity.(2) The differences in sedimentary water environments lead to the heterogeneity in lithology, lithofacies, and organic material types of source rocks;the differences in material source supply and sedimentary facies belt result in reservoirs of different lithologies, including argillaceous and transition rocks, and tight siltstone, and complex source-reservoir combination types.(3) The heterogeneity of the source rock controls the differentiation of hydrocarbon generation and expulsion, the diverse reservoir types make reservoir performance different and the source-reservoir configurations complex, and these two factors ultimately make the shale oil enrichment patterns different. Among them, the hydrocarbon generation and expulsion capacity of high-quality source rocks affect the degree of shale oil enrichment. Freshwater hydrocarbon source rocks with TOC larger than 2.5% and saline hydrocarbon source rocks with TOC of 2% to 10% have a high content of retained hydrocarbons and are favorable.(4) High-abundance organic shale is the basis for the enrichment of shale oil inside the source. In addition to being retained in shale, liquid hydrocarbons migrate along laminae, diagenetic fractures, and thin sandy layers, and then accumulate in laminae of argillaceous siltstone, siltstone, and argillaceous dolomite, and dolomitic siltstone suites, etc. with low organic matter abundance in the shale strata, resulting in differences in enrichment pattern.

New CICC Design Versions with High Copper Fraction for HT-7U Tokamak

The peak fields of HT-7U TF/PF coils are designed at 5.8 T and 4.5 T, respectively. The superconducting (SC) NbTi/Cu strands for the coils have a quite low copper fraction (0.58). To increase the ratio of the limiting current Vs. critical current for the cable in conduit conductor (CICC), the first-stage subcable consists of several copper strands twisted around a SC composite one. The copper strand diameter is different from the SC one. Based on Bottura's CICC design approach we take the product of total copper cross-section and wetted perimeter as one of the key design parameters to meet with stability margin requirement. The product reaches 114 cm3 for 15.5 kA TF CICC at operating temperature of 4.2 K and 139 cm3 for 15 kA PF CICC at 3.8 K to obtain stability margins of 280 and 700 mJ/cm3, respectively.