In recent years,there has been a significant acceleration in the thinning,calving and retreat of the Pine Island Ice Shelf(PIIS).The basal channels,results of enhanced basal melting,have the potential to significantly...In recent years,there has been a significant acceleration in the thinning,calving and retreat of the Pine Island Ice Shelf(PIIS).The basal channels,results of enhanced basal melting,have the potential to significantly impact the stability of the PIIS.In this study,we used a variety of remote sensing data,including Landsat,REMA DEM,ICESat-1 and ICESat-2 satellite altimetry observations,and Ice Bridge airborne measurements,to study the spatiotemporal changes in the basal channels from 2003 to 2020 and basal melt rate from 2010 to 2017 of the PIIS under the Eulerian framework.We found that the basal channels are highly developed in the PIIS,with a total length exceeding 450 km.Most of the basal channels are ocean-sourced or groundingline-sourced basal channels,caused by the rapid melting under the ice shelf or near the groundingline.A raised seabed prevented warm water intrusion into the eastern branch of the PIIS,resulting in a lower basal melt rate in that area.In contrast,a deepsea trough facilitates warm seawater into the mainstream and the western branch of the PIIS,resulting in a higher basal melt rate in the main-stream,and the surface elevation changes above the basal channels of the mainstream and western branch are more significant.The El Ni?o event in 2015–2016 possibly slowed down the basal melting of the PIIS by modulating wind field,surface sea temperature and depth seawater temperature.Ocean and atmospheric changes were driven by El Ni?o,which can further explain and confirm the changes in the basal melting of the PIIS.展开更多
Large-size primary MC carbides can significantly reduce the performance of M2 high-speed steel.To better control the morphology and size of primary MC carbides,the effect of melting rate on microsegregation and primar...Large-size primary MC carbides can significantly reduce the performance of M2 high-speed steel.To better control the morphology and size of primary MC carbides,the effect of melting rate on microsegregation and primary MC carbides of M2 steel during electroslag remelting was investigated.When the melting rate is decreased from 2 kg·min^(-1) to 0.8 kg·min^(-1),the columnar dendrites are gradually coarsened,and the extent of segregation of Mo and V is alleviated,while the segregation of Cr becomes severe.At 2 kg·min^(-1),the number of primary MC carbides per unit area with the sizes in the range of 2 μm to 6 μm accounts for about 75% of all MC carbides,while the carbides are mainly concentrated on the size larger than 8 μm at 0.8 kg·min^(-1).Thermodynamic calculations based on the Clyne-Kurz (simplified to C-K) model shows that MC carbide can be precipitated in the final solidification stage and a smaller secondary dendrite arm spacing caused by higher melting rate (2 kg·min^(-1) in this experiment) facilitates the refinement of primary MC carbides.展开更多
Microstructure and variations in porosity in Ti-6Al-4V samples built with electron beam melting (EBM) over a range of melt scan speeds, ranging from 100 mm·s-1 to 1000 mm·s-1 were examined. Microstructure wa...Microstructure and variations in porosity in Ti-6Al-4V samples built with electron beam melting (EBM) over a range of melt scan speeds, ranging from 100 mm·s-1 to 1000 mm·s-1 were examined. Microstructure was characterized by refinement of α-phase and transformation to α′-martensite. Light optical microscopy, scanning electron microscopy, and transmission electron microscopy were used to observe these phenomena, while corresponding tensile testing and associated macro and microindentation hardness measurements were used to define the microstructural variations. Relative stiffness was observed to be linearly log-log related to relative density, corresponding to ideal porosity associated with open-cellular structures.展开更多
In the electroslag remelting process, the electrode molten state is a critical factor determining the ingot quality, while the electrode immersion depth and melting rate are key factors for the stability of the electr...In the electroslag remelting process, the electrode molten state is a critical factor determining the ingot quality, while the electrode immersion depth and melting rate are key factors for the stability of the electroslag re-melting process. Studies were carried out to investigate the microscopic and macroscopic effects of electrode immersion depth and melting rate on the potential distribution and heat density in the slag bath, and on the depth and shape of the molten bath. Based on the finite element method and the numerical solution method, the effect of the electrode immersion depth on the slag bath heat density was researched; the relationship between the electrode immersion depth and the slag resistance was obtained; and the unsteady-state model of the solidification process of the re-melting ingot was solved using the finite difference method. The mathematical model and physical model of the electrode melting process were established and solved; and the corresponding curves between the electrode molten-state and slag-bath physical parameters were obtained. The experimental results verified the simulated results studied in this paper.展开更多
The relation between the melting point of Portland cement raw meal and its heating rate have been studied. The raw meal was burnt at different heating rate ranging from 10 similar to 900 degrees C/min Dy the following...The relation between the melting point of Portland cement raw meal and its heating rate have been studied. The raw meal was burnt at different heating rate ranging from 10 similar to 900 degrees C/min Dy the following methods: (A) in electric resistance furnace; (B) in DTA-TG analyzer with infrared ray focused heating; (C) in high temperature microscope with electron stream heating. Based on thermal analysis theory and melt theory and the tests above, it is found that melting point T-m of cement raw meal decreases with the increased heating rate Phi during burning in the following relation: T-m=1280-0.107 empty set.展开更多
Based on the pre-existing wire melting rate model of direct-current submerged arc welding （ DC-SAW） , a new numerical model of wire melting rate was developed for variable-polarity submerged are welding （VP-SAW） b...Based on the pre-existing wire melting rate model of direct-current submerged arc welding （ DC-SAW） , a new numerical model of wire melting rate was developed for variable-polarity submerged are welding （VP-SAW） by accounting for the combined effects of duty cycle β and offset α. The experimental measurements are in a good agreement with the results calculated by this new wire melting rate model, with the maximum discrepancy being less than 10%. Therefore it is evident that this new numerical model can successfully describe the dependence of wire melting rate on the duty cycle β and offset α.展开更多
基金The National Natural Science Foundation of China under contract Nos 41941010 and 42006184the Fundamental Research Funds for the Central Universities under contract No.2042022kf1068。
文摘In recent years,there has been a significant acceleration in the thinning,calving and retreat of the Pine Island Ice Shelf(PIIS).The basal channels,results of enhanced basal melting,have the potential to significantly impact the stability of the PIIS.In this study,we used a variety of remote sensing data,including Landsat,REMA DEM,ICESat-1 and ICESat-2 satellite altimetry observations,and Ice Bridge airborne measurements,to study the spatiotemporal changes in the basal channels from 2003 to 2020 and basal melt rate from 2010 to 2017 of the PIIS under the Eulerian framework.We found that the basal channels are highly developed in the PIIS,with a total length exceeding 450 km.Most of the basal channels are ocean-sourced or groundingline-sourced basal channels,caused by the rapid melting under the ice shelf or near the groundingline.A raised seabed prevented warm water intrusion into the eastern branch of the PIIS,resulting in a lower basal melt rate in that area.In contrast,a deepsea trough facilitates warm seawater into the mainstream and the western branch of the PIIS,resulting in a higher basal melt rate in the main-stream,and the surface elevation changes above the basal channels of the mainstream and western branch are more significant.The El Ni?o event in 2015–2016 possibly slowed down the basal melting of the PIIS by modulating wind field,surface sea temperature and depth seawater temperature.Ocean and atmospheric changes were driven by El Ni?o,which can further explain and confirm the changes in the basal melting of the PIIS.
基金financially supported by the National Natural Science Foundation of China(No.51904087)the Open Project of State Key Laboratory of Advanced Special Steel,Shanghai Key Laboratory of Advanced Ferrometallurgy,Shanghai University(SKLASS 2019-20)+2 种基金the Science and Technology Commission of Shanghai Municipality(No.19DZ2270200)the Natural Science Foundation-Steel and Iron Foundation of Hebei Province(No.E2019202482)Tianjin Science and Technology Project(No.18YFZCGX00220)。
文摘Large-size primary MC carbides can significantly reduce the performance of M2 high-speed steel.To better control the morphology and size of primary MC carbides,the effect of melting rate on microsegregation and primary MC carbides of M2 steel during electroslag remelting was investigated.When the melting rate is decreased from 2 kg·min^(-1) to 0.8 kg·min^(-1),the columnar dendrites are gradually coarsened,and the extent of segregation of Mo and V is alleviated,while the segregation of Cr becomes severe.At 2 kg·min^(-1),the number of primary MC carbides per unit area with the sizes in the range of 2 μm to 6 μm accounts for about 75% of all MC carbides,while the carbides are mainly concentrated on the size larger than 8 μm at 0.8 kg·min^(-1).Thermodynamic calculations based on the Clyne-Kurz (simplified to C-K) model shows that MC carbide can be precipitated in the final solidification stage and a smaller secondary dendrite arm spacing caused by higher melting rate (2 kg·min^(-1) in this experiment) facilitates the refinement of primary MC carbides.
文摘Microstructure and variations in porosity in Ti-6Al-4V samples built with electron beam melting (EBM) over a range of melt scan speeds, ranging from 100 mm·s-1 to 1000 mm·s-1 were examined. Microstructure was characterized by refinement of α-phase and transformation to α′-martensite. Light optical microscopy, scanning electron microscopy, and transmission electron microscopy were used to observe these phenomena, while corresponding tensile testing and associated macro and microindentation hardness measurements were used to define the microstructural variations. Relative stiffness was observed to be linearly log-log related to relative density, corresponding to ideal porosity associated with open-cellular structures.
基金financially supported by the Machine Tools Major Project of the Eleventh Five-Year Plan of China(grant No.2009ZX04006-032)
文摘In the electroslag remelting process, the electrode molten state is a critical factor determining the ingot quality, while the electrode immersion depth and melting rate are key factors for the stability of the electroslag re-melting process. Studies were carried out to investigate the microscopic and macroscopic effects of electrode immersion depth and melting rate on the potential distribution and heat density in the slag bath, and on the depth and shape of the molten bath. Based on the finite element method and the numerical solution method, the effect of the electrode immersion depth on the slag bath heat density was researched; the relationship between the electrode immersion depth and the slag resistance was obtained; and the unsteady-state model of the solidification process of the re-melting ingot was solved using the finite difference method. The mathematical model and physical model of the electrode melting process were established and solved; and the corresponding curves between the electrode molten-state and slag-bath physical parameters were obtained. The experimental results verified the simulated results studied in this paper.
文摘The relation between the melting point of Portland cement raw meal and its heating rate have been studied. The raw meal was burnt at different heating rate ranging from 10 similar to 900 degrees C/min Dy the following methods: (A) in electric resistance furnace; (B) in DTA-TG analyzer with infrared ray focused heating; (C) in high temperature microscope with electron stream heating. Based on thermal analysis theory and melt theory and the tests above, it is found that melting point T-m of cement raw meal decreases with the increased heating rate Phi during burning in the following relation: T-m=1280-0.107 empty set.
文摘Based on the pre-existing wire melting rate model of direct-current submerged arc welding （ DC-SAW） , a new numerical model of wire melting rate was developed for variable-polarity submerged are welding （VP-SAW） by accounting for the combined effects of duty cycle β and offset α. The experimental measurements are in a good agreement with the results calculated by this new wire melting rate model, with the maximum discrepancy being less than 10%. Therefore it is evident that this new numerical model can successfully describe the dependence of wire melting rate on the duty cycle β and offset α.
