The main features of martensite transformation in melt-quenched Fe-31.4% Ni alloy on cooling below room temperature have been studied. It is found that the ribbon 50～60 μm thick, prepared by spinning technique, is a...The main features of martensite transformation in melt-quenched Fe-31.4% Ni alloy on cooling below room temperature have been studied. It is found that the ribbon 50～60 μm thick, prepared by spinning technique, is a natural composite in which isothermal and surface martensite are not formed, while athermal martensite forms at lower temperature, all factors being the same, as compared to the alloy of the same composition and grain size, prepared by recrystallization.展开更多
The microstructure and magnetostrictive properties were investigated in the Tb doped Fe83Ga17-xTbx（x = 0.05, 0.10, 0.20, 0.30, 0.40, 0.50） bulk rods prepared by melt rapidly quenching. The partial solid solubility o...The microstructure and magnetostrictive properties were investigated in the Tb doped Fe83Ga17-xTbx（x = 0.05, 0.10, 0.20, 0.30, 0.40, 0.50） bulk rods prepared by melt rapidly quenching. The partial solid solubility of Tb in the Fe-Ga matrix was preliminary detected by the lattice parameters and SEM observation. The matrix keeps A2 structure and the second phase appears surround the grain boundary as x C 0.1. h100 i preferred orientation is also observed for x = 0.1 sample along the axis of the quenched rod. The saturation magnetostriction first increases and maximum value reaches at x = 0.1, and then decreases with Tb addition increasing. The initial increase of the magnetostriction should be associated with the partial solution of Tb in the matrix, the maximum value at x = 0.1 should be attributed to the h100 i preferred orientation, and the decrease of the magnetostriction is correlated with the appearance of the second phase along the grain boundary.展开更多
Rapid liquid quenching was accomplished by using an arc-melting piston and anvil apparatus.A small amount of the rare earth element Nd in melt quenched Ti80Si2o alloy promotes eutectic precipitation of β-Ti and Ti5Si...Rapid liquid quenching was accomplished by using an arc-melting piston and anvil apparatus.A small amount of the rare earth element Nd in melt quenched Ti80Si2o alloy promotes eutectic precipitation of β-Ti and Ti5Si3.An orientation relationship of the Ti5Si3 and the β-Ti phase is <2113>∥<001>β-Ti,(0110)∥(110)β-Ti.The alloy forming heat of the Ti5Si3 is more negative than that of the β-Ti phase and the Ti5Si3 precipitates first.展开更多
The relationships between microstructure and melting temperature of slag containing different heavy metals （Zn, Cu, Pb and Cr） were studied. Furthermore, the corresponding solidification mechanism and rule of heavy ...The relationships between microstructure and melting temperature of slag containing different heavy metals （Zn, Cu, Pb and Cr） were studied. Furthermore, the corresponding solidification mechanism and rule of heavy metals were analyzed by microscopic tests during melting and reconstructing process. Based on preliminary results, three conclusions were derived. Firstly, pure slag would begin to melt when the temperature reached 1 180℃; however, Zn did not play any fluxing action. Secondly, upon adding Cu and Pb, the initial melting temperature of slag decreased by 5-8℃ and their fluxing effect was observed. Thirdly, the initial melting temperature and the reaction time for slag decreased by 22℃ and 6 s respectively after adding Cr; the fluxing action was significant under Cr. The results of X-ray diffraction （XRD） and Fourier transform infrared spectroscope （FTIR） analyses showed that the above heavy metals had little influence on the reconstruction of slag. Toxicity characteristic leaching procedure （TCLP） leaching tests showed a good solidification effect of the heavy metals with melting slag, fixation rate of Zn, Cu, Pb and Cr was 36.3%, 24.6%, 9.2% and 93.2%, respectively. The leaching toxicity of the heavy metals met the requirements for environmental emission after solidification treatment.展开更多
文摘The main features of martensite transformation in melt-quenched Fe-31.4% Ni alloy on cooling below room temperature have been studied. It is found that the ribbon 50～60 μm thick, prepared by spinning technique, is a natural composite in which isothermal and surface martensite are not formed, while athermal martensite forms at lower temperature, all factors being the same, as compared to the alloy of the same composition and grain size, prepared by recrystallization.
基金financially supported by the National Basic Research Program of China (No. 2012CB619404)the National Natural Science Foundations of China (Nos. 50925101, 51101006, 91016006 and 51221163)the Fundamental Research Funds for the Central Universities
文摘The microstructure and magnetostrictive properties were investigated in the Tb doped Fe83Ga17-xTbx（x = 0.05, 0.10, 0.20, 0.30, 0.40, 0.50） bulk rods prepared by melt rapidly quenching. The partial solid solubility of Tb in the Fe-Ga matrix was preliminary detected by the lattice parameters and SEM observation. The matrix keeps A2 structure and the second phase appears surround the grain boundary as x C 0.1. h100 i preferred orientation is also observed for x = 0.1 sample along the axis of the quenched rod. The saturation magnetostriction first increases and maximum value reaches at x = 0.1, and then decreases with Tb addition increasing. The initial increase of the magnetostriction should be associated with the partial solution of Tb in the matrix, the maximum value at x = 0.1 should be attributed to the h100 i preferred orientation, and the decrease of the magnetostriction is correlated with the appearance of the second phase along the grain boundary.
文摘Rapid liquid quenching was accomplished by using an arc-melting piston and anvil apparatus.A small amount of the rare earth element Nd in melt quenched Ti80Si2o alloy promotes eutectic precipitation of β-Ti and Ti5Si3.An orientation relationship of the Ti5Si3 and the β-Ti phase is <2113>∥<001>β-Ti,(0110)∥(110)β-Ti.The alloy forming heat of the Ti5Si3 is more negative than that of the β-Ti phase and the Ti5Si3 precipitates first.
基金Funded by the National Natural Science Foundation of China(Nos.51202222,51002110)the State Key Laboratory of Silicate Materials for Architectures(Wuhan University of Technology)(No.SYSJJ2013-07)
文摘The relationships between microstructure and melting temperature of slag containing different heavy metals （Zn, Cu, Pb and Cr） were studied. Furthermore, the corresponding solidification mechanism and rule of heavy metals were analyzed by microscopic tests during melting and reconstructing process. Based on preliminary results, three conclusions were derived. Firstly, pure slag would begin to melt when the temperature reached 1 180℃; however, Zn did not play any fluxing action. Secondly, upon adding Cu and Pb, the initial melting temperature of slag decreased by 5-8℃ and their fluxing effect was observed. Thirdly, the initial melting temperature and the reaction time for slag decreased by 22℃ and 6 s respectively after adding Cr; the fluxing action was significant under Cr. The results of X-ray diffraction （XRD） and Fourier transform infrared spectroscope （FTIR） analyses showed that the above heavy metals had little influence on the reconstruction of slag. Toxicity characteristic leaching procedure （TCLP） leaching tests showed a good solidification effect of the heavy metals with melting slag, fixation rate of Zn, Cu, Pb and Cr was 36.3%, 24.6%, 9.2% and 93.2%, respectively. The leaching toxicity of the heavy metals met the requirements for environmental emission after solidification treatment.
