Woody biomass is a renewable source offering high potential for production of bio-fuels,-chemicals and-energy.During the outdoor storage of biomass biodegradation processes take place,which leads to mass reduction up ...Woody biomass is a renewable source offering high potential for production of bio-fuels,-chemicals and-energy.During the outdoor storage of biomass biodegradation processes take place,which leads to mass reduction up to 30 wt%.To avoid these mass losses,the biomass was mixed with Ca(OH)_(2) in different ratios.To ensure,that this additive does not negatively influence further thermo-chemical conversion of biomass(e.g.by fluidized bed combustion),the spruce and poplar ash with and without additive was tested using ash melting microscopy.It was demonstrated that all the characteristic temperatures(DT,HT,FT)were significantly higher than the thermo-chemical conversion process temperatures in a fluidized bed.Thus it could be pointed out that the addition of Ca(OH)_(2) does not negatively influence ash melting behaviour,ash melting temperature respectively.展开更多
An integral constitutive equation and a set of material functions for describing the strain history of polymer melts were formulated in terms of the Cauchy-Green and Finger tensors. A simple memory function and the de...An integral constitutive equation and a set of material functions for describing the strain history of polymer melts were formulated in terms of the Cauchy-Green and Finger tensors. A simple memory function and the dependence of ηo and τt on M3.4 were derived from the theory of non-linear viscoelasticity with constraints of entanglements for polymer melts and substituted into the Oldroye-Walters-Fredickson constitutive equation. An integral constitutive equation for polymer melts was consequently obtained. Some material functions of the constitutive equation related to certain 'test flow' are examined as follows : (1) simple steady shear flow; (2) steady elongation flow; (3) small-amplitude oscillatory shear flow; (4) stress growth upon the inception of steady shear elongation flow; (5) stress relaxation (modulus and compllance). These theoretical relations for simple steady shear flow were compared with experimental data from our laboratory and references for various polymer melts and concentrated solutions. A good agreement between the theory and experiment was achieved.展开更多
It is shown theoretically that the viscoelasticity of polymer melts is determined by three combining factorst they are the primary molecular weight and its distribution, the number of entanglement sites on polymer cha...It is shown theoretically that the viscoelasticity of polymer melts is determined by three combining factorst they are the primary molecular weight and its distribution, the number of entanglement sites on polymer chain and the sequence distribution of constituent chains in entanglement spacings. A unified quantity for the three combing factors is the average constrained dimensional number of constituent chains in the long entanglement spacings (v). A new relation of v to the primary molecular weight and the number of testing polymers were derived from the multiple entanglement and reptation model, and a new method for determining v was proposed. The dependences of linear viscoelastic functions on the primary molecular weight and its distribution were derived by the statistical method. When Mn=6Me to 18 Me, the values of (v) can range from 3.33 to 3.70. Their values are in a good agreement with the experiment data, and it can slightjy vary with the different species of polymers and the different ranges of molecular weight of polymers展开更多
An approach of stochastically statistical mechanics and a unified molecular theory of nonlinear viscoelasticity with constraints of Nagai chain entanglement for polymer melts have been proposed. A multimode model stru...An approach of stochastically statistical mechanics and a unified molecular theory of nonlinear viscoelasticity with constraints of Nagai chain entanglement for polymer melts have been proposed. A multimode model structure for a single polymer chain with n tail segments and N reversible entanglement sites on the test polymer chain is developed. Based on the above model structure and the mechanism of molecular flow by the dynamical reorganization of entanglement sites, the probability distribution function of the end-to-end vectr for a single polymer chain at entangled state and the viscoelastic free energy of deformation for polymer melts are calculated by using the method of the stochastically statistical mechanics. The four types of stress-strain relation and the memory function are derived from this thery. The above theoretical relations are verified by the experimentaf data for various polymer melts. These relations are found to be in good agreement with the experimental results展开更多
Fused deposition modelling (FDM) is a filament based rapid prototyping system which offers the possibility of introducing new composite material for the FDM process as long as the new material can be made in feedstock...Fused deposition modelling (FDM) is a filament based rapid prototyping system which offers the possibility of introducing new composite material for the FDM process as long as the new material can be made in feedstock filament form. Swinburne has been undertaking extensive research in development of new composite materials involving acrylonitrile-butadiene-styrene (ABS) and other materials including metals. In order to predict the behaviour of new ABS based composite materials in the course of FDM process, it is necessary to investigate the flow of the composite material in liquefier head. No such study is available considering the geometry of the liquefier head. This paper presents 2-D and 3-D numerical analysis of melt flow behaviour of a representative ABS-iron composite through the 90-degree bent tube of the liquefier head of the fused deposition modelling process using ANSYS FLOTRAN and CFX finite element packages. Main flow parameters including temperature, velocity, and pressure drop have been investigated. Filaments of the filled ABS have been fabricated and characterized to verify the possibility of prototyping using the new material on the current FDM machine. Results provide promising information in developing the melt flow modelling of metal-plastic composites and in optimising the FDM parameters for better part quality with such composites.展开更多
基金Funding from the Austrian Research Promotion Agency(FFG)(Project BioAdd,Proj.nr.858837)。
文摘Woody biomass is a renewable source offering high potential for production of bio-fuels,-chemicals and-energy.During the outdoor storage of biomass biodegradation processes take place,which leads to mass reduction up to 30 wt%.To avoid these mass losses,the biomass was mixed with Ca(OH)_(2) in different ratios.To ensure,that this additive does not negatively influence further thermo-chemical conversion of biomass(e.g.by fluidized bed combustion),the spruce and poplar ash with and without additive was tested using ash melting microscopy.It was demonstrated that all the characteristic temperatures(DT,HT,FT)were significantly higher than the thermo-chemical conversion process temperatures in a fluidized bed.Thus it could be pointed out that the addition of Ca(OH)_(2) does not negatively influence ash melting behaviour,ash melting temperature respectively.
文摘An integral constitutive equation and a set of material functions for describing the strain history of polymer melts were formulated in terms of the Cauchy-Green and Finger tensors. A simple memory function and the dependence of ηo and τt on M3.4 were derived from the theory of non-linear viscoelasticity with constraints of entanglements for polymer melts and substituted into the Oldroye-Walters-Fredickson constitutive equation. An integral constitutive equation for polymer melts was consequently obtained. Some material functions of the constitutive equation related to certain 'test flow' are examined as follows : (1) simple steady shear flow; (2) steady elongation flow; (3) small-amplitude oscillatory shear flow; (4) stress growth upon the inception of steady shear elongation flow; (5) stress relaxation (modulus and compllance). These theoretical relations for simple steady shear flow were compared with experimental data from our laboratory and references for various polymer melts and concentrated solutions. A good agreement between the theory and experiment was achieved.
文摘It is shown theoretically that the viscoelasticity of polymer melts is determined by three combining factorst they are the primary molecular weight and its distribution, the number of entanglement sites on polymer chain and the sequence distribution of constituent chains in entanglement spacings. A unified quantity for the three combing factors is the average constrained dimensional number of constituent chains in the long entanglement spacings (v). A new relation of v to the primary molecular weight and the number of testing polymers were derived from the multiple entanglement and reptation model, and a new method for determining v was proposed. The dependences of linear viscoelastic functions on the primary molecular weight and its distribution were derived by the statistical method. When Mn=6Me to 18 Me, the values of (v) can range from 3.33 to 3.70. Their values are in a good agreement with the experiment data, and it can slightjy vary with the different species of polymers and the different ranges of molecular weight of polymers
文摘An approach of stochastically statistical mechanics and a unified molecular theory of nonlinear viscoelasticity with constraints of Nagai chain entanglement for polymer melts have been proposed. A multimode model structure for a single polymer chain with n tail segments and N reversible entanglement sites on the test polymer chain is developed. Based on the above model structure and the mechanism of molecular flow by the dynamical reorganization of entanglement sites, the probability distribution function of the end-to-end vectr for a single polymer chain at entangled state and the viscoelastic free energy of deformation for polymer melts are calculated by using the method of the stochastically statistical mechanics. The four types of stress-strain relation and the memory function are derived from this thery. The above theoretical relations are verified by the experimentaf data for various polymer melts. These relations are found to be in good agreement with the experimental results
文摘Fused deposition modelling (FDM) is a filament based rapid prototyping system which offers the possibility of introducing new composite material for the FDM process as long as the new material can be made in feedstock filament form. Swinburne has been undertaking extensive research in development of new composite materials involving acrylonitrile-butadiene-styrene (ABS) and other materials including metals. In order to predict the behaviour of new ABS based composite materials in the course of FDM process, it is necessary to investigate the flow of the composite material in liquefier head. No such study is available considering the geometry of the liquefier head. This paper presents 2-D and 3-D numerical analysis of melt flow behaviour of a representative ABS-iron composite through the 90-degree bent tube of the liquefier head of the fused deposition modelling process using ANSYS FLOTRAN and CFX finite element packages. Main flow parameters including temperature, velocity, and pressure drop have been investigated. Filaments of the filled ABS have been fabricated and characterized to verify the possibility of prototyping using the new material on the current FDM machine. Results provide promising information in developing the melt flow modelling of metal-plastic composites and in optimising the FDM parameters for better part quality with such composites.
