Effects of Freeze/Thaw Cycles and Gas Purging Method on Polymer Electrolyte Membrane Fuel Cells

At subzero temperature, the startup capability and performance of polymer electrolyte membrane fuel cell (PEMFC) deteriorates markedly. The object of this work is to study the degradation mechanism of key components of PEMFC-membrane-electrode assembly (MEA) and seek feasible measures to avoid degradation. The effect of freeze/thaw cycles on the structure of MEA is investigated based on porosity and SEM measurement. The performance of a single cell was also tested before and after repetitious freeze/thaw cycles. The experimental results indicated that the performance of a PEMFC decreased along with the total operating time as well as the pore size distribution shifting and micro configuration changing. However, when the redundant water had been removed by gas purging, the performance of the PEMFC stack was almost resumed when it experienced again the same subzero temperature test. These results show that it is necessary to remove the water in PEMFCs to maintain stable performance under subzero temperature and gas purging is proved to be the effective operation.

MORPHOLOGIES AND GAS SEPARATION PROPERTIES OF MELT-SPUN ASYMMETRIC POLY(4-METHYL-1-PENTENE)HOLLOW FIBER MEMBRANES

Poly(4-methyl-1-pentene) (PMP) hollow fiber membranes were prepared by the melt-spun and cold-stretch(MSCS) method. Scanning electronic microscopy (SEM) was used to characterize the section and surface structures of themembranes with special asymmetric structure. The preliminary results of gas permeation measurements indicated that the resultant hollow fiber membranes have the potential ability for oxygen/nitrogen separation.

Preparation of Composite Microporous Silica Membranes Using TEOS and 1,2-Bis(triethoxysilyl)ethane as Precursors for Gas Separation

This paper reports on a new microporous composite silica membrane prepared via acid-catalyzed polymeric route of sol-gel method with tetraethylorthosilicate(TEOS)and a bridged silsesquioxane[1,2-bis(triethoxysilyl)ethane, BTESE]as precursors.A stable nano-sized composite silica sol with a mean volume size of^5 nm was synthesized. A 150 nm-thick defect-free composite silica membrane was deposited on disk support consisting of macroporous α-Al2O3 and mesoporousγ-Al2O3 intermediate layer by using dip-coating approach,followed by calcination under pure nitrogen atmosphere.The composite silica membranes exhibit molecular sieve properties for small gases like H2,CO2,O2,N2,CH4 and SF6 with hydrogen permeances in the range of(1-4)×10 -7mol·m -2·s -1·Pa -1(measured at 200°C,3.0×105 Pa).With respect to the membrane calcined at 500°C,it is found that the permselectivities of H 2 (0.289 nm)with respect to N2(0.365 nm),CH4(0.384 nm)and SF6(0.55 nm)are 22.9,42 and>1000,respectively, which are all much higher than the corresponding Knudsen values(H2/N2=3.7,H2/CH4=2.8,and H2/SF6=8.5).

Controlling pore structures of Pd-doped organosilica membranes by calcination atmosphere for gas separation

Pd-doped organosilica membranes were prepared by controlling calcination atmospheres(i.e.POS-Air,POS-N2,POS-H2,POS-H2/N2)to tailor their networks for improving their gas separation performance.This study shows that Pd(Ⅱ)could be only maintained under non-reductive calcination atmosphere,while inert and reducing calcination atmosphere is more beneficial to maintain organosilica moieties in POS networks.POS-H2/N2 membrane showed the optimal H2 separation performance that its permselectivities for H2/CO2,H2/N2,H2/CH4 and H2/SF6 are 15.0,96.7,173.0 and 3400.0,re spectively.Moreover,it is found that H2 molecules pass through the four membranes based on activated diffusion,while CO2 molecules permeation through POS-N2 and POS-Air membrane is dominated by surface diffusion.This work may provide insight into the understanding of the calcination atmosphere effect on gas separation performance of metal-doped organosilica membranes.

Support surface pore structures matter: Effects of support surface pore structures on the TFC gas separation membrane performance over a wide pressure range

In this work, the effects of support surface pore structures(including surface pore size, surface pore density and surface porosity) on the performance of thin film composite(TFC) gas separation membrane over a wide pressure range(from 0.3 to 2.0 MPa) were studied. To fulfill it, the polysulfone(PSf) supports with different surface pore structures were prepared. Two kinds of wide-accepted polymeric membrane materials, i.e., polyvinylamine(PVAm) and Pebax 1657 copolymer, were used as skin layer materials. We pointed out for the first time that the support surface average pore size and pore density could affect the chain mobility of polymer of skin layer at the support surface pore entrance, then, can affect the TFC membrane performance. Besides, we also discussed the effects of support on the TFC membrane performance when the feed pressure changes for the first time. This work can provide guidance for choosing a suitable support for TFC gas separation membrane.

Tuning sol size to optimize organosilica membranes for gas separation

A series of organosilica sols are prepared by the polymeric sol–gel method using 1,2-bis(triethoxysilyl)ethane(BTESE)as the precursor.Particle size distributions of the BTESE-derived sols are systematically investigated by carefully adjusting the synthesis parameters(i.e.,water ratios,acid ratios and solvent ratios)in the sol process.In certain conditions,increasing the water ratio or the acid ratio tends to cause larger sol sizes and bimodal particle size distributions.However,higher solvent ratios lead to smaller sol sizes and unimodal particle size distributions.The organosilica membranes prepared from the optimized sols show excellent H_2 permeances(up to 4.2×10^(-7)mol·m^(-2)·s^(-1)·Pa^(-1))and gas permselectitivies(H_2/CO_2 is 9.5,H_2/N_2 is 50 and H_2/CH_4 is 68).This study offers significant insights into the relationship between the sol synthesis parameters,sol sizes and membrane performance.

Enhanced gas separation performance of mixed matrix hollow fiber membranes containing post-functionalized S-MIL-53

Mixed matrix hollow fiber membranes（MMHFMs）filled with metal-organic frameworks（MOFs）have great potential for energy-efficient gas separation processes,but the major hurdle is polymer/MOFs interfacial defects and membrane plasticization.Herein,lab-synthesized MIL-53 was post-functionalized by aminosilane grafting and subsequently incorporated into Ultem-1000 polymer matrix to fabricate high performance MMHFMs.SEM,DLS,XRD and TGA were performed to characterize silane-modified MIL-53（S-MIL-53）and prepared MMHFMs.Moreover,the effect of MOFs loading was systematically investigated first;then gas separation performance of MMHFMs for pure and mixed gas was evaluated under different pressures.MMHFMs containing post-functionalized S-MIL-53 achieved remarkable gas permeation properties which was better than model predictions.Compared to pure HFMs,CO2permeance of MMHFM loaded with 15%S-MIL-53 increased by 157%accompanying with 40%increase for CO2/N2selectivity,which outperformed the MMHFM filled with naked MIL-53.The pure and mixed gas permeation measurements with elevated feed pressure indicated that incorporation of S-MIL-53 also increased the resistance against CO2plasticization.This work reveals that post-modified MOFs embedded in MMHFMs facilitate the improvement of gas separation performance and suppression of membrane plasticization.

A hybrid zeolitic imidazolate framework Co-IM-mIM membrane for gas separation

A zeolitic imidazolate hybrid membrane(Co-IM-mIM) containing two imidazolate ligands deposited on a macroporous α-alumina support was prepared by pre-depositing and secondary growth technique. XRD, TGA and SEM characterizations demonstrate that a stable and thin, but dense and pure-phase Co-IM-mIM membrane can be obtained on the macroporous-alumina discs in Teflon-lined autoclave at 120 °C after pre-depositing by dip-coating at room temperature. No visible cracks, pinholes or other defects were observed on the membrane layer. The gas separation studies of Co-IM-mIM membrane were carried out at 25 °C and 1×10~5 Pa, showing ideal selectivity of 6.95, 5.25, 3.40 for H_2/CO_2, H_2/N_2 and H_2/CH_4, respectively, and a permeance of 17.37× 10^(-6) mol/(m^2·s·Pa) for H_2. The influence of temperature and trans-membrane pressure on hydrogen separation and permeation was also carried out. The gas permeation and selectivity demonstrate that this membrane may have potential applications for efficient H_2 separation.

Gas separation using sol–gel derived microporous zirconia membranes with high hydrothermal stability

A microporous zirconia membrane with hydrogen permeance about 5 × 10-8mol·m-2·s-1·Pa-1, H2/CO2 permselectivity of ca. 14, and excellent hydrothermal stability under steam pressure of 100 k Pa was fabricated via polymeric sol–gel process. The effect of calcination temperature on single gas permeance of sol–gel derived zirconia membranes was investigated. Zirconia membranes calcined at 350 °C and 400 °C showed similar single gas permeance, with permselectivities of hydrogen towards other gases, such as oxygen, nitrogen, methane, and sulfur hexa fluoride, around Knudsen values. A much lower CO2permeance（3.7 × 10-9mol·m-2·s-1·Pa-1）was observed due to the interaction between CO2 molecules and pore wall of membrane. Higher calcination temperature, 500 °C, led to the formation of mesoporous structure and, hence, the membrane lost its molecular sieving property towards hydrogen and carbon dioxide. The stability of zirconia membrane in the presence of hot steam was also investigated. Exposed to 100 k Pa steam for 400 h, the membrane performance kept unchanged in comparison with freshly prepared one, with hydrogen and carbon dioxide permeances of 4.7 × 10-8and ~ 3 × 10-9mol·m-2·s-1·Pa-1, respectively. Both H2 and CO2permeances of the zirconia membrane decreased with exposure time to 100 k Pa steam. With a total exposure time of 1250 h, the membrane presented hydrogen permeance of 2.4 × 10-8mol·m-2·s-1·Pa-1and H2/CO2 permselectivity of 28, indicating that the membrane retains its microporous structure.

Distinguished discriminatory separation of CO2 from its methane-containing gas mixture via PEBAX mixed matrix membrane

Highly selective separation of CO_2 from its methane-containing binary gas mixture can be achieved by using Poly(ether-block-amide)(PEBAX)mixed matrix membranes(MMMs).According to FESEM and AFM analyses,silica-based nanoparticles were homogenously integrated within the polymer matrix,facilitating penetration of CO_2 through the membrane while acting as barrier for methane gas.The membrane containing 4.6 wt% fumed silica(FS)(PEBAX/4.6 wt%FS)exhibits astonishing selectivity results where binary gas mixture of CO_2/CH_4 was used as feed gas.As detected by gas chromatography,in the permeate side,data showed a significant increase of CO_2 permeance,while CH_4 transport through the mixed matrix membrane was not detectable.Moreover,PEBAX/4.6 wt%FS greatly exceeds the Robeson limit.According to data reported on CO_2/CH_4 gas pair separation in the literature,the results achieved in this work are beyond those data reported in the literature,particularly when PEBAX/4.6 wt%FS membrane was utilized.

A CONDENSED REVIEW ON THE FABRICATION OF HOLLOW FIBER MEMBRANES FOR GAS SEPARATION:HISTORICAL DEVELOPMENT AND TECHNOLOGY CHALLENGES AHEAD

A review on the polymeric hollow fibers membranes for gas separation has been conducted. In order to deyelop high performance membranes for gas separation, there are a few technology challenges awaiting the chemical engineers to overcome. There are four major challenges, namely: 1) material selection and synthesis; 2) fabrication of hollow fiber membranes with an ultra- thin dense selective layer; 3) materials against plasticization; and 4) aging. In each area, we summarize the scientific accomplishments and technical difficulties.

Effects of Freeze/Thaw Cycles and Gas Purging Method on Polymer Electrolyte Membrane Fuel Cells

At subzero temperature, the startup capability and performance of polymer electrolyte membrane fuel cell PEMFC deteriorates markedly. The object of this work is to study the degradation mechanism of key compo- nents of PEMFC—membrane-electrode assembly MEA and seek feasible measures to avoid degradation. The ef- fect of freezethaw cycles on the structure of MEA is investigated based on porosity and SEM measurement. The performance of a single cell was also tested before and after repetitious freezethaw cycles. The experimental results indicated that the performance of a PEMFC decreased along with the total operating time as well as the pore size distribution shifting and micro configuration changing. However, when the redundant water had been removed by gas purging, the performance of the PEMFC stack was almost resumed when it experienced again the same subzero temperature test. These results show that it is necessary to remove the water in PEMFCs to maintain stable per- formance under subzero temperature and gas purging is proved to be the effective operation.

Polymeric Membranes Used in Natural Gas Processing to Separate Carbon Dioxide： the Facing Problems and Solutions

For the last two decades polymeric membranes have been used in several gas separation processes. For the high selectivity and permeability various types of membranes have been developed. Thin layers to high dense and hollow fiber to asymmetric wounded materials to determine the effective separation of CO2 from CH4 were used. Ideal membrane materials must have provisions of durability, chemical and thermal resistance, effective separation and economical production and operation. In this review it is observed that most of the polymeric materials face plasticization problem in the separation of CO2 from CH4. This is due to the condensable nature of carbon dioxide that causes swelling in most of the polymeric membranes due to which the efficiency of selectivity and permeability is affected. Most extensive works have been carried out in developing the chemical structure and compositions of polymeric materials to improve the separation properties. Cross-linking and blending of molecular sieving called ＂mixed-matrix＂ are the most useful approaches applied in this regard, but no where it is found to be fully effective and ideal polymeric membranes commercially fit to replace the existing systems of CO2 separation from the natural gas. Still area is open to work on to produce more worth full materials and switch towards liquid membranes and hybrid systems.

First membrane unit for separating CO_2 from natural gas operational

After a more-than-two-week trial operation, a new membrane unit based on the technology developed by researchers from the CAS Dalian Institute of

Conventional processes and membrane technology for carbon dioxide removal from natural gas:A review

Membrane technology is becoming more important for CO,_ separation from natural gas in the new era due to its process simplicity, relative ease of operation and control, compact, and easy to scale up as compared with conventional processes. Conventional processes such as absorption and adsorption for CO2 separation from natural gas are generally more energy demanding and costly for both operation and maintenance. Polymeric membranes are the current commercial membranes used for CO2 separation from natural gas. However, polymeric membranes possess drawbacks such as low permeability and selectivity, plasticization at high temperatures, as well as insufficient thermal and chemical stability. The shortcomings of commercial polymeric membranes have motivated researchers to opt for other alternatives, especially inorganic membranes due to their higher thermal stability, good chemical resistance to solvents, high mechanical strength and long lifetime. Surface modifications can be utilized in inorganic membranes to further enhance the selectivity, permeability or catalytic activities of the membrane. This paper is to provide a comprehensive review on gas separation, comparing membrane technology with other conventional methods of recovering CO2 from natural gas, challenges of current commercial polymeric membranes and inorganic membranes for CO2 removal and membrane surface modification for improved selectivity.

Non-equilibrium Molecular Dynamics Simulation on Pure Gas Permeability Through Carbon Membranes

The permeation of various pure gas （H2, He, Ne, CH4 and At） through carbon membranes is investigated using a dual control volume grand canonical molecular dynamics method. A two-dimensional slit pore is employed instead of the one-dimensional pore. Compared with the experiments, simulation results show that the improvement of pore model is very necessary. The effects of membrane thickness, pore width and temperature on gas permeance and ideal separation factor are also discussed. Results show that gas permeates through membrane according to Knudsen diffusion in large pore, while Knudsen diffusion is accompanied by molecular sieving in small pore. Moreover, methane is easily adsorbed on the membrane surface due to strong attractive interactions of membrane and shows higher permeance than that of Knudsen flow. In addition, it is noted that when membrane thickness is thin enough the permeance of gas does not decrease with the increase of membrane thickness due to the strong adsorption until membrane resistance becomes dominant.

Polyurethane-SAPO-34 mixed matrix membrane for CO_2/CH_4 and CO_2/N_2 separation

SAPO-34 nanocrystals(inorganic filler) were incorporated in polyurethane membranes and the permeation properties of CO_2, CH_4,and N_2 gases were explored. In this regard, the synthesized PU-SAPO-34 mixed matrix membranes(MMMs) were characterized via SEM, AFM, TGA, XRD and FTIR analyses. Gas permeation properties of PU-SAPO-34 MMMs with SAPO-34 contents of 5 wt%, 10 wt% and 20 wt% were investigated. The permeation results revealed that the presence of 20 wt% SAPO-34 resulted in 4.45%, 18.24% and 40.2% reductions in permeability of CO_2,CH_4,and N_2, respectively, as compared to the permeability of neat polyurethane membrane. Also,the findings showed that at the pressure of 1.2 MPa, the incorporation of 20 wt% SAPO-34 into the polyurethane membranes enhanced the selectivity of CO_2/CH_4 and CO_2/N_2, 14.43 and 37.46%, respectively. In this research, PU containing 20 wt% SAPO-34 showed the best separation performance. For the first time, polynomial regression(PR) as a simple yet accurate tool yielded a mathematical equation for the prediction of permeabilities with high accuracy(R^2>99%).

Natural gas purification by asymmetric membranes: An overview

Natural gas, as a very important source of energy and chemical feedstock, can be used in place of coal to lower net carbon dioxide emissions.Membrane separation technology is an attractive alternative for natural gas purification where the impurities represented by acid gases(CO_(2) and H_(2)S) as well as inert gases(N_(2)) must be removed to meet the transportation and usage specifications. From the economic benefits viewpoint,asymmetric membranes are required for industrial manufacture and applications. This paper aims to review the latest development of various kinds of asymmetric membranes for natural gas purification, mainly focusing on CO_(2) removal from CH_(4), including H_(2)S and N_(2) separation from CH_(4) as well. According to material types, polymeric, inorganic, mixed-matrix and carbon molecular sieve membranes are introduced. The associated fabrication approaches and transport properties are discussed for each kinds of asymmetric membranes. Towards the practical implementation, an emphasis is placed on hollow fiber asymmetric structure for these polymeric, mixed-matrix and carbon molecular sieve membranes.

COMPETITIVE FACILITATED TRANSPORT OF ACID GASES IN MODIFIED CARRIER MEMBRANES

1 INTRODUCTIONMany attempts to develop semipermeable membranes for gas separation have beendone over the past twenty years [1,2].However,it is still difficult to prepare apolymer film which makes certain gas separation processed within range of being econ-omically and technically feasible,since most polymeric materials are relativelyimpermeable to gases.Facilitated transport concept which was first proposed

Indispensable gutter layers in thin-film composite membranes for carbon capture

Industrial thin-film composite(TFC)membranes achieve superior gas separation properties from high-performance selective layer materials,while the success of membrane technology relies on high-performance gutter layers to achieve production scalability and low-cost manufacturing.However,the current literature predominantly focuses on the design of polymer architectures to obtain high permeability and selectivity,while the art of fabricating gutter layers is usually safeguarded by industrial manufacturers and appears lackluster to academic researchers.This is the first report aiming to provide a comprehensive and critical review of state-of-the-art gutter layer materials and their design and modification to enable TFC membranes with superior separation performance.We first elucidate the importance of the gutter layer on membrane performance through modeling and experimental results.Then various gutter layer materials used to obtain high-performance composite membranes are critically reviewed,and the strategies to improve their compatibility with the selective layer are highlighted,such as oxygen plasma treatment,polydopamine deposition,and surface grafting.Finally,we present the opportunities of the gutter layer design for practical applications.