Metal Sealing Performance of Subsea X-tree Wellhead Connector Sealer

The metal sealing performance of subsea X-tree wellhead connectors is crucial for the safety and reliability of subsea X-trees. In order to establish the theoretical relation between metal sealing ring＇s contact stress and its structural parameters and working pressure, a mechanical analysis method for double-cone sealing of high pressure vessels is applied in analyzing the metal sealing ring under the condition of preload and operation. As a result, the formula of the unit sealing load for the metal sealing ring under operation with residual preload is shown in this paper, which ensures that the metal sealing ring has an excellent sealing effect and can prevent the metal sealing ring from yielding. Besides, while analyzing the sealing process of the metal sealing ring, the change rule of contact stress and working pressure is concluded here, putting forward that the structural parameters of the metal sealing ring are the major factors affecting the change rule. Finally, the analytical solution through theoretical analysis is compared with the simulation result through finite element analysis in a force feedback experiment, and both are consistent with each other, which fully verifies for the design and calculation theory on metal sealing ring＇s contact stress and its structural parameters and working pressure deduced in this paper. The proposed research will be treated as an applicable theory guiding the design of metal seal for subsea X-tree wellhead connectors.

Rare Earth Application in Sealing Anodized Al-Based Metal Matrix Composites

A new method for corrosion protection of Al-based metal matrix composites (MMC) was developed using two-step process, which involves anodizing in H2SO4 solution and sealing in rare earth solution. Corrosion resistance of the treated surface was evaluated with polarization curves. The results showed that the effect of the protection using rare earth sealing is equivalent to that using chromate sealing for Al6061/SiCp. The rare earth metal salt can be an alternative to the toxic chromate for sealing anodized Al MMC.

Application of a Modified Arrhenius Equation to Describe the Time-Temperature Equivalence in Relaxation Analysis of Metal Seals

For the application of the time-temperature superposition principle a suitable relation is needed to describe the time-temperature shift factor a. Therefore, the Arrhenius equation is widely used due to its simple form and often leads to suitable results. Where, the Arrhenius equation presents a linear relation for the temperature-dependent shift factor in logarithmic scale ln（α） with the absolute inverse temperature （1/θ）. However, in cases with a large temperature range which eventually include more complex reaction processes, the functional relation between ln（α） and （1/θ） is nonlinear in the ＇Arrhenius plot＇. In those cases, the monotone change of the nonlinear range in the ＇Arrhenius plot＇ can be interpreted as a transient range between two approximately linear or constant regions. An extended application of the modified Arrhenius equation from Nakamura （1989） is presented in this study for this transient range. The introduced method was applied to describe the time-temperature equivalence in the relaxation analysis of restoring seal force of metal seals, which are used in lid-systems of transport and interim storage casks for radioactive materials. But, the method is widely valid and can be used for different objectives which are characterized by thermorheologically simple behavior with nonlinear sensitivity to inverse temperature.

Study on Thermal Expansion Coefficient of Sealing Materials for Ceramic Metal Halide Lamps

With Al2O3, Dy2O3, and SiO2 as starting materials, the basic glass of Al2O3-Dy2O3-SiO2 system was prepared by conventional melting technology, and their thermal expansion coefficients （TECs） at different anneal time were investigated. TECs of the basic glass, which were heat-treated under different temperature, were also investigated. The result showed that TECs of the basic glass gradually approached a fixed value as the anneal time was extended, which suggested that most of the inner stress had been eliminated. After heat treatment, the contents of Dy2O3, Dy2Si2O7, and a new crystal increased up to 1200 ℃ and decreased below 1250 ℃, which was consistent with the TEC change of crystallized samples. This suggests that the crystal has a direct effect on TECs of the crystallized samples.

Stress and thickness calculation of a bolted flat cover with double metal sealing rings

The design of a bolted flat cover is extremely important for the structural integrity of pressure vessels.The present design codes provide the thickness calculation equations for a bolted flat cover with single metal gasket.However,the rules for a bolted flat cover with double metal sealing rings are not developed to date.In the study,a new thickness calculation equation for the bolted flat cover with double metal sealing rings is proposed.First,the theoretical stress solution for bolted flat cover with the double metal sealing rings is obtained,based on the theory of simply supported circular plate and then verified using the results from finite element analyses.The results indicate that the influence of double metal sealing ring on the stress of the flat cover is more serious compared to single metal gasket.Second,a more accurate and reasonable equation is proposed to calculate the thickness of bolted flat cover with double metal sealing rings based on the derived theoretical equations of maximum stress.Finally,the influence of linear load and the spacing between rings on the thickness are discussed.Subsequently,a few suggestions are provided to design low-pressure or atmosphere pressure vessels.The study provides a theoretical foundation to develop design codes of pressure vessels in nuclear reactors.

具有圆度误差的径向金属密封接触应力研究

由于加工圆度误差的影响,井下流量控制阀径向金属密封接触应力分布不均匀,从而影响密封性能。利用有限元方法研究具有圆度误差的径向金属密封唇部接触应力分布,并分析圆度误差对径向金属密封接触应力的影响;基于有限元分析结果提出径向金属密封接触应力分布的理论解析式,并进行误差分析。具有圆度误差的径向金属密封唇部接触应力分布的理论解与数值解相符,各参数引起的最大接触应力的平均相对误差约为10%。根据具有圆度误差的径向金属密封副接触应力的分布规律,提出合理的过盈量函数,修正了径向金属密封轴对称结构的悬臂梁模型的接触应力理论关系式,得出了圆度误差下的径向金属密封接触应力分布规律。研究结果为井下流量控制阀径向金属密封的设计提供了理论指导。

W形密封结构金属封隔器性能研究

针对橡胶封隔器难以适应150℃、70 MPa以上环境的缺点,设计一种适用于230℃、70 MPa工况,两端传递载荷,中间中空促进径向变形的W形密封结构的金属封隔器,并研究其密封性能。根据工况需求,以温度依赖性和超弹性激发应力选择β-NiTi合金作为W形密封结构材料,以W形结构坐封后产生的接触应力评价其密封性能,以工作承压后W形结构的弹性-超弹性应变率评价其解封性能,分析W形密封结构半径、壁厚及壁厚比对其密封性能的影响,并对设计优化后的W形结构进行密封性能仿真分析。结果表明:结构半径对W形密封结构的密封性能和解封性能影响较小,而壁厚与壁厚比均显著影响密封性能和解封性能;随着壁厚的增加,W形密封结构的密封性能逐渐下降但解封性能逐渐上升,随着壁厚比的增加,密封性能逐渐下降解封性能先上升后下降。对设计优化后的W形结构进行密封性能仿真分析,结果表明,基于β-NiTi合金材料的W形密封结构金属封隔器完全可以适用于高温高压环境,其在230℃、70 MPa的工况下坐封载荷为220 kN,弹性-超弹性应变率达90%以上。

铋酸盐封接玻璃的研究及其连接应用现状

无铅低温封接玻璃由于具有绿色安全、成本低、封接温度低等优势,被广泛应用于航空航天、电真空、集成电路等领域。在磷酸盐、钒酸盐、硼酸盐和铋酸盐等多种封接玻璃体系中,因铋与铅具有相似的性质特点,使得铋酸盐玻璃成为最有可能替代铅酸盐玻璃的绿色玻璃钎料。综述了铋酸盐玻璃的成分和性能调控、网络结构的研究现状,介绍了目前使用铋酸盐封接玻璃进行金属、陶瓷同质/异质材料连接的研究进展,最后对未来的发展趋势进行了展望。

流量控制阀K形金属密封圈结构参数优化

流量控制阀K形金属密封圈结构参数较多,且不同结构参数对密封性能影响程度存在较大差异。以密封面接触压力、密封面有效接触长度及最大Mises应力为约束条件,采用正交试验设计研究影响K形金属密封圈密封性能结构参数之间的主次关系,确定了唇部长度、悬臂内张角与悬臂厚度3个因素作为响应曲面法的设计变量;通过正交试验和回归分析得到接触压力、最大等效应力及有效接触长度与设计参数关系的二次回归方程,并基于响应面法对密封结构进行优化分析。优化后K形金属密封圈的接触压力增加了8.09%,有效接触长度增加了14.73%,最大等效应力减少了13.44%,表明优化后K形金属密封圈密封面接触压力分布更加均匀,有效提高了金属密封圈的密封性能。

激光封接金属与玻璃研究进展

玻璃与金属的焊接在微电子封装、真空管及蓝宝石金属窗等多个领域展现出广泛的应用前景。然而,这一技术也面临诸多限制,主要源于玻璃与金属在结构上的差异、连接本质的复杂性,以及润湿、铺展和粘结等复杂物理现象的挑战。激光焊接技术,凭借其高精度、能量集中和加工快速等优势,在玻璃与金属的封接中获得了广泛应用。本文介绍了玻璃与金属焊接的应用领域及其存在的限制,概述了激光焊接金属与玻璃的研究现况,并深入分析了激光参数对焊接质量的影响规律。最后,探讨了激光焊接金属与玻璃的潜在应用,为玻璃与金属复合结构的制造提供创新性的指导思路,同时也为激光焊接技术在该领域的应用提供参考。

井下应急封隔器结构设计及胶筒坐封效果评价

为应对海洋钻井过程出现的高压溢流和井涌风险,设计了一种井下应急封隔器装置,在内外胶筒间添加金属骨架提高其坐封强度。为评估井下应急封隔器的坐封效果,利用有限元方法建立井下应急封隔器模型,模拟了封隔器的坐封过程,并对比了金属骨架对胶筒接触应力、坐封效果的影响。结果表明:20 MPa坐封压力下,胶筒与套管接触应力达到12.1 MPa,封隔器能够封堵20 MPa井下溢流;添加金属骨架后,胶筒峰值应力、变形均显著降低,坐封能力大幅提升。所设计的井下应急封隔器装置可实现高压溢流、井涌的有效封堵,保障平台作业安全。

芯轴式封隔器金属密封设计及密封性能分析

针对油页岩、页岩油、重质油和富油煤等非常规油气资源采用地下原位改质技术开采,井下存在高温、高压和腐蚀环境,常规封隔器及其密封不能满足工程要求的问题,设计了一种芯轴式金属对金属密封的井下封隔器,密封副采用耐高温和腐蚀的Inconel 625材料,其中密封座采用金属陶瓷涂层结构。进行了封隔器坐封密封原理试验。试验结果表明,封隔器能在油套大环空间隙形成密封,且密封能力随着坐封载荷的增加而增大。基于密封接触能原理,应用ANSYS软件模拟了井下封隔器的密封性能,并对其影响因素进行研究。研究结果表明:涂层厚度和涂层弹性模量对密封能力影响不显著;芯轴密封面椭圆率和过盈量对密封能力影响较大,起决定性作用。基于密封副高温、持久载荷作用下许用应力低和密封能力评价指标,给出了密封结构参数设计方案,密封座涂层材料为Cr_(3)C_(2)-NiCr,涂层弹性模量250 GPa,涂层厚度为0.3 mm,椭圆率为,过盈量为0.02 mm。研究结果可为高温、高压、腐蚀环境下封隔器的开发和应用提供理论指导。

三偏心蝶阀硬密封结构的响应面优化

金属硬密封三偏心蝶阀在关闭状态下的密封比压决定着该阀的密封性能和工作寿命,优化金属硬密封部件的结构参数十分重要。以DN600三偏心蝶阀为研究对象,利用有限元分析法,分析密封面上密封比压分布规律。提出利用密封配合面周向间隙指标判断蝶阀的密封性能,利用Box-Behnken响应面优化方法对密封构件的结构进行优化,分析复合阀板座大、小径端切割厚度、复合阀板座直径及其交互作用对密封面最大密封比压的影响,得出最优设计方案。结果表明,在不影响蝶阀密封的前提下,优化复合阀板座参数后,密封面最大密封比压从202.96 MPa下降到128.44 MPa。对优化后蝶阀进行封闭打压密封实验,验证了其密封性能的可靠性。

水下井口连接器研发现状及密封关键技术研究进展

水下井口连接器是连接水下采油树与井口头的关键设备,为了加快国内水下井口连接器的研发进程,对国内外水下井口连接器发展现状进行了广泛调研,国外水下井口连接器产品系列完善,5家供应商占据了市场垄断地位;国内对水下井口连接器的研究起步较晚,但目前也初步实现了浅水及深水井口连接器的工程化应用。针对水下井口连接器最为关键的金属对金属密封问题,从密封数值模拟、理论及试验、热-力耦合、密封优化设计等方面研究进展进行了剖析,指出基于线弹性二维或三维有限元方法分析水下井口连接器的非线性问题存在一定偏差;理论方法难以准确推导出水下井口连接器在复合载荷下的密封载荷传递关系,相关试验也难以精确模拟水下井口连接器的真实工况和载荷条件;热-力耦合分析未充分考虑传热边界和初始温度条件,简单按照经验法选取对流换热系数和导热系数,导致连接器密封热-力耦合的温度求解不准确,也缺少相关试验验证压力-温度共同作用下的金属密封能力;密封优化设计方面,目前主要针对接触应力单一目标进行优化,需以接触应力、结构强度、尺寸等多目标进行优化,多角度评估优化后的水下井口连接器结构力学性能。建议深入开展水下井口连接器设计、制造、检验标准的适用性研究,全方位评估水下井口连接器密封影响因素并完善水下井口连接器的密封试验内容,突破水下井口连接器密封关键技术,形成水下井口连接器的研发技术体系,实现海洋油气开发水下井口连接器从浅水到深水、超深水系列化标准化产品。

面向磁流体增强的骨架结构微成型设计及回弹特性研究

为提高磁流体密封液膜的刚度和抗压力性能,设计一种应用于磁流体密封的翻边Z型增强骨架,该骨架由软磁金属薄板微成型冲压而成。对软磁金属电工纯铁和无取向硅钢进行单向拉伸试验,得到2种材料的应力应变曲线。利用幂硬化准则对Z型骨架成型回弹特性进行理论分析,确定影响回弹的主要因素为材料参数、厚度、弯曲半径、开孔宽度等。利用有限元软件对成型回弹过程进行仿真,应用因素水平分析,以残余应变和最大回弹量为指标,分析板胚厚度、弯曲半径、开孔宽度对回弹的影响。仿真结果表明:在研究的范围内通过增大板胚厚度、减小弯曲半径、减小翅片宽度能有效降低骨架回弹;当厚度为0.3 mm,弯曲半径0.3 mm,翅片尺寸为2 mm×1 mm时骨架成型回弹量最小,运用硅钢材料比纯铁具有更小的回弹量。研究结果对软磁金属的微成型冲压及磁流体密封复合材料设计提供了参考。

金属封严环数字孪生几何模型框架的开发与应用

金属封严环广泛应用于航空发动机密封系统,其型面成形质量对飞行器高性能、高可靠服役具有重要影响。然而,薄壁、复杂的异形截面与封闭的环形结构等导致其在几何质量检测方面存在以下问题:其一,成形结果严重依赖于破坏性抽样终检,实际产品均未经过完整质量检测;其二,成形过程无几何质量检测手段,无法及时发现成形缺陷,轮廓几何数据的缺失,使工艺优化设计困难。因此,提出一种金属封严环数字孪生几何模型框架,该框架包括:物理空间、虚拟空间、交互空间与服务,可提供在机测量平台标定、截面轮廓测量、点云数据预处理、截面几何特征计算、三维数模快速构建、三维型面动态测量与偏差计算等连续成形质量在线检测技术,建立起反映金属封严环成形过程中变化的数字孪生几何模型,从而为金属封严环成形质量的检测、分析、预测以及后续工艺优化设计所需的基础数据获取等提供支撑。在此基础上,研制了在线检测模拟试验装置与数字孪生软件,介绍了金属封严环数字孪生几何模型的应用情况。

金属盖板镀层形貌对平行缝焊器件抗盐雾性能的影响

气密性封装是高可靠集成电路制造的关键技术。探讨了金属盖板表面镀层形貌对平行缝焊器件耐盐雾性能的影响。研究发现,平行缝焊后金属盖板表面出现的贯穿性裂纹是降低平行缝焊器件耐盐雾性能的关键因素。在相同封帽参数下,表面镀层为长条形晶胞的盖板封帽后出现多条贯穿性裂纹,无法通过24 h盐雾试验后气密性检测。而表面镀层为均匀大小的圆形晶胞的盖板具备更高的抗封帽裂纹能力,封帽后无贯穿性裂纹出现,且可通过48 h盐雾试验后气密性检测。

芯轴式套管悬挂器金属密封设计及性能分析

为了避免芯轴式套管悬挂器密封失效,根据芯轴式套管悬挂器的结构及密封工作原理,设计了一种新型的金属密封结构。建立了芯轴式悬挂器密封性能有限元模型,研究了不同顶丝压力和套管悬重对密封锥面变形及接触压力的影响。结果表明:随顶丝推力的增加,上、下密封锥面上平均接触压力都增加,有利于实现密封;随套管悬重的增加,上密封锥平均接触压力增加,下密封锥平均接触压力减小,除下内锥面外,均能满足密封要求。研究结果可为芯轴式悬挂器密封部位的结构设计提供参考。

无框门系统设计思考和实践

本文以某硬派越野车为例,对无框车门系统设计的关键要素进行思考与总结。无框车门钣金系统只有水切下的部分,作为系统载体,文中总结了其应具备的结构特点和性能要求;无框车门密封系统结构复杂,文中介绍了关键密封断面和力学性能要求;玻璃升降系统采用了双导轨设计,文中对其重要设计参数要求进行了分析与总结。某硬派越野车装车实践后效果良好,本文的设计思考证实可靠。

防钛火隔热层抗开裂界面粗糙化设计制备研究

钛合金在航空发动机中应用广泛,但它们在遇到剧烈冲击、摩擦等极端情况时易发生钛火,继而引起整台发动机着火,造成严重后果。在钛合金表面涂覆阻燃涂层是目前解决钛火问题的主要方法之一。然而,阻燃涂层是由陶瓷隔热层与金属基可磨耗面层组成的多层复合结构,在服役过程中,陶瓷/金属异质界面常发生剥落失效。基于此,主要开展陶瓷隔热层表面粗糙化设计,提升涂层抗开裂能力。首先,为确定喷涂工艺对粉末熔化程度的影响规律,采用模拟与试验相结合的方法,研究了空心与实心两种YSZ粉末粒子在等离子束流内的加热加速过程,明确了调控粉末熔化状态的控制参数,试验沉积单个扁平粒子验证了模拟结果的合理性。其次,开展了陶瓷隔热层表面形貌调控研究。基于模拟结果,确定隔热层主体应采用高功率,以保证粉末充分熔化;表面粗化层采用较低功率以获得半熔化态氧化锆球壳,从而制备得到表面具有较大粗糙度、内部具有良好隔热防钛火功能的新型隔热层结构。涂层表面的粗糙化设计,有利于提高金属陶瓷的异质界面结合强度,支撑涂层的长寿命防护。