Osteoblast Behavior on Hierarchical Micro-/Nano-Structured Titanium Surface

In the present work, osteoblast behavior on a hierarchical micro-/nano-structured titanium surface was investigated. A hi- erarchical hybrid micro-/nano-structured titanium surface topography was produced via Electrolytic Etching （EE）. MG-63 cells were cultured on disks for 2 h to 7 days. The osteoblast response to the hierarchical hybrid micro-/nano-structured titanium surface was evaluated through the osteoblast cell morphology, attachment and proliferation. For comparison, MG-63 cells were also cultured on Sandblasted and Acid-etched （SEA） as well as Machined （M） surfaces respectively. The results show signifi- cant differences in the adhesion rates and proliferation levels of MG-63 cells on EE, SLA, and M surfaces. Both adhesion rate and proliferation level on EE surface are higher than those on SLA and M surfaces. Therefore, we may expect that, comparing with SLA and M surfaces, bone growth on EE surface could be accelerated and bone formation could be promoted at an early stage, which could be applied in the clinical practices for immediate and early-stage loadings.

Preparation of micro/nano-structured ceramic coatings on Ti6Al4V alloy by plasma electrolytic oxidation process

In order to improve the osseointegration and antibacterial activity of titanium alloys,micro/nano-structured ceramic coatings doped with antibacterial element F were prepared by plasma electrolytic oxidation(PEO)process on Ti6Al4V alloy in NaF electrolyte.The influence of NaF concentration(0.15-0.50 mol/L)on the PEO process,microstructure,phase composition,corrosion resistance and thickness of the coatings was investigated using scanning/transmission electron microscopy,energy dispersive spectroscopy,atomic force microscopy,X-ray diffractometer,and potentiodynamic polarization.The results demonstrated that Ti6Al4V alloy had low PEO voltage(less than 200 V)in NaF electrolyte,which decreased further as the NaF concentration increased.A micro/nano-structured coating with 10-15μm pits and 200-800 nm pores was formed in NaF electrolyte;the morphology was different from the typical pancake structure obtained with other electrolytes.The coating formed in NaF electrolyte had low surface roughness and was thin(<4μm).The NaF concentration had a small effect on the phase transition from metastable anatase phase to stable rutile phase,but greatly affected the corrosion resistance.In general,as the NaF concentration increased,the surface roughness,phase(anatase and rutile)contents,corrosion resistance,and thickness of the coating first increased and then decreased,reaching the maximum values at 0.25 mol/L NaF.

不同方法对根管内氢氧化钙去除效果的micro-CT评价

目的:应用显微CT(micro-computed tomography,micro-CT)建立磨牙根管模型,评价不同方法对氢氧化钙的清除效率。方法:收集2023年10月—2024年2月口腔综合科门诊拔除的11颗磨牙(24个根管),按照标准根管治疗流程,镍钛器械预备完成后,在根管内置入氢氧化钙,1周后,根据不同冲洗方法将样本随机分为侧方开口注射器组、超声荡洗组(EMS组)和声波震荡组(EDDY组)等3组(n=8)。冲洗前后使用micro-CT重建根管系统并使用不同颜色标记独立根管,计算各个根管氢氧化钙体积,比较各组氢氧化钙清除率。采用SPSS 19.0软件包对数据进行统计学分析。结果:3种方法均无法完全去净根管内氢氧化钙。使用次氯酸钠作为冲洗液时,超声荡洗和声波震荡清除效果优于侧方开口冲洗器(P<0.05);超声荡洗和声波震荡去除氢氧化钙效率相当,差异无统计学意义(P>0.05);氢氧化钙残留部位集中于根尖区。结论:Micro-CT能较为高效地重建磨牙根管模型,可用于评价氢氧化钙去除效果。超声荡洗组和声波震荡组清除氢氧化钙效率相当,优于侧方开口注射器组。

Micro LED车灯投影光学系统设计与优化

本文提出了一种基于Micro LED阵列的车灯投影方案,设计了以像素尺寸为80μm×80μm的200×150白光Micro LED阵列作为显示光源,视场角为16°×34°的车灯投影光学系统,并对物面倾斜角度和光学系统结构进行了优化。此外,分别采用反向畸变处理方法和像素灰度调制方法用以解决车灯投影图像的梯形畸变和照度均匀性问题,并搭建了投影实验平台,对图像校正方法进行了验证。实验结果表明:校正后图像梯形畸变系数p1,p2分别从0.0932和0.3680下降至0.0835和0.0373,像面照度均匀性从83.2%提高到93.2%。本文通过对基于Micro LED的倾斜投影车灯光学系统进行优化设计及采用图像校正方法,实现了高光效、低畸变的车灯投影。

Self-assembled germanium nano-structures by laser-assisted oxidation

The investigation on the oxidation behaviour of Si1-xGex alloys （x=0.05, 0.15, and 0.25） is carried out. It is found for the first time that on the oxide film a germanium nano-cap with a thickness of 1.8-2.8nm and a few Ge nanoparticles with diameters ranging from 5.5 nm to 10 nm are formed by the low-temperatu.re laser-assisted dry oxidation of Si1-xGex substrate. A new scanning method on the decline cross-section of the multiple-layer sample is adopted to measure the layer thickness and the composition. Some new peaks in photoluminescence （PL） spectra are discovered, which could be related to the nano-cap and the nano-particles of germanium. A suitable model and several new calculating formulae with the unrestricted Hartree-Fock-Roothaan （UHFR） method and quantum confinement analysis are proposed to interpret the PL spectra and the nano-structure mechanism in the oxide.

光子晶体Micro LED微显示阵列加工及光学特性分析

Micro LED器件具有高亮度、低功耗和高可靠性等优点,但Micro LED显示像素巨量转移和光提取效率低的问题为其应用带来挑战。开发了具有高转移效率和出光效率的单片64×64 Micro LED微显示阵列,提出了倒装型GaN基单片Micro LED微显示阵列芯片和Si基驱动电路的设计方法及集成工艺。通过时域有限差分(FDTD)方法对Micro LED微显示阵列光学特性进行了建模分析,设计了一种提高Micro LED微显示阵列出光效率的光提取结构。结合仿真结果,开发了一种在Micro LED蓝宝石衬底表面制备光子晶体结构的聚焦离子束(FIB)微纳加工工艺,并进行了器件加工。测试结果表明,蓝宝石衬底上加工的光子晶体结构可以提高Micro LED器件的表面出光效率,光功率平均值提升了16.36%,对Micro LED微显示阵列加工及微显示像素光提取问题具有借鉴意义。

Preparation and Characterization of Nano-Structured SiO_(2) Thin Films on Carbon Steel

Nano-structured SiO2 thin films were prepared on the surface of carbon steel for the first time by LPD. The compositions of the films were analyzed by XPS, and the surface morphology of the thin films were observed by AFM. The thin films were constituted by compact particles of SiO2, and there was no Fe in the films. In the process of film forming, the SiO2 colloid particles were deposited or absorbed directly onto the surface of carbon steel substrates that were activated by acid solution containing inhibitor, and corrosion of the substrates was avoided. The nano-structured SiO2 thin films that were prepared had excellent protective efficiency to the carbon steel.

One-dimensional nano-structure of Cu-Zn-Al alloy

Cu-Zn-Al alloy of one dimensional nano-structure was prepared and thestructure of obtained nano-material was characterized by transmission electron microscope (TEM). Itwas shown that there are non-linear oscillations on the surface of Cu-Zn-Al alloy and theconsanguineous connection exists between non-linear oscillation and the growth process of onedimensional nano-structure. The diameter of one dimensional nano-structure is about 40 nm, and theratio of length to diameter is over 40. Finally, the growth mechanism of one dimensionalnano-structure was also studied.

Electron emission degradation of nano-structured sp^2-bonded amorphous carbon films

The initial field electron emission degradation behaviour of original nano-structured sp^2-bonded amorphous carbon films has been observed, which can be attributed to the increase of the work function of the film in the field emission process analysed using a Fowler-Nordheim plot. The possible reason for the change of work function is suggested to be the desorption of hydrogen from the original hydrogen termination film surface due to field emission current-induced local heating. For the explanation of the emission degradation behaviour of the nano-structured sp2-bonded amorphous carbon film, a cluster model with a series of graphite （0001） basal surfaces has been presented, and the theoretical calculations have been performed to investigate work functions of graphite （0001） surfaces with different hydrogen atom and ion chemisorption sites by using first principles method based on density functional theory-local density approximation.

Preparation of nano-structured Ag solid materials and application to surface-enhanced Raman scattering

Silver nano-particles with average diameter of about 60 nm were compacted in a high-strength mold under different pressures at 523 K to produce nano-structured Ag solid materials. The structure and characteristic of the nano-structured Ag solid materials (NSS-Ag) were studied using X-ray diffraction (XRD), scanning electron microscope (SEM) and Raman spectrometer. The NSS-Ag could be used as highly efficient surface-enhanced Raman scattering (SERS) active substrates. The common probe molecules Rhodamine 6G (R6G, 1×10-10 mol/L) were used to test the SERS activity on these substrates at very low concentrations. It is found that the SERS enhancement ability is dependent on the density of NSS-Ag. When the relative density of NSS-Ag is 83.87%, the materials reveal great SERS signal.

基于Micro CT的铜导线短路熔痕孔洞特征分析

导线短路是造成电气火灾的重要原因之一。现行国家标准中将导线短路熔痕分为起火前发生的一次短路熔痕和起火后造成的二次短路熔痕,然而现行国家标准中的鉴定仅停留在定性判断的阶段。火灾现场铜导线短路熔痕特征的量化分析研究是国内外研究人员主要关注的重点。本文应用Micro CT技术对铜导线短路熔痕进行断层扫描检测并重构铜导线短路熔痕的3D图像数据,在此基础上统计、归纳、总结铜导线短路熔痕内部孔洞形态及分布等孔洞特征。研究表明,Micro CT能够全面采集铜导线短路熔痕的整体形态和内部孔洞特征,一次短路熔痕与二次短路熔痕内部孔洞半径、表面积、紧密度的特征数据存在差别,可为短路熔痕定性和定量分析判据研究提供新的理论依据。

Nano-Structure Observed in Highly Doped Silicon Crystalline

It was reported that due to the non-linear electrical phenomena,the super-saturated arsenic in silicon single crystalline precipitates during post processing at low temperatures to form different structures.The structure with spatial period of 1.7 to 2.3 nm was observed firstly by TEM on the sample.

Analysis of the Carbon Nano-Structures Formation in Liquid Arcing

Graphite electrodes were used for the direct current （DC） arc discharge in water. And high-resolution transmission electron microscopy （HRTEM） was used to investigate the products. Based on the experimental phenomena and nano-structure products, arc plasma characteristics in water were analyzed theoretically. Two growth regions and relevant growth modes were proposed to interpret the formation mechanisms of nano-structures by arc discharge in water. Furthermore, liquid nitrogen and cross magnetic field was applied to change the arcing state respectively, and new carbon nano-structures were obtained. Their formation mechanisms were also analyzed correspondingly.

Micro segment analysis of supercritical methane thermal-hydraulic performance and pseudo-boiling in a PCHE straight channel

The printed circuit heat exchanger(PCHE) is receiving wide attention as a new kind of compact heat exchanger and is considered as a promising vaporizer in the LNG process. In this paper, a PCHE straight channel in the length of 500 mm is established, with a semicircular cross section in a diameter of 1.2 mm.Numerical simulation is employed to investigate the flow and heat transfer performance of supercritical methane in the channel. The pseudo-boiling theory is adopted and the liquid-like, two-phase-like, and vapor-like regimes are divided for supercritical methane to analyze the heat transfer and flow features.The results are presented in micro segment to show the local convective heat transfer coefficient and pressure drop. It shows that the convective heat transfer coefficient in segments along the channel has a significant peak feature near the pseudo-critical point and a heat transfer deterioration when the average fluid temperature in the segment is higher than the pseudo-critical point. The reason is explained with the generation of vapor-like film near the channel wall that the peak feature related to a nucleateboiling-like state and heat transfer deterioration related to a film-boiling-like state. The effects of parameters, including mass flow rate, pressure, and wall heat flux on flow and heat transfer were analyzed.In calculating of the averaged heat transfer coefficient of the whole channel, the traditional method shows significant deviation and the micro segment weighted average method is adopted. The pressure drop can mainly be affected by the mass flux and pressure and little affected by the wall heat flux. The peak of the convective heat transfer coefficient can only form at high mass flux, low wall heat flux, and near critical pressure, in which condition the nucleate-boiling-like state is easier to appear. Moreover,heat transfer deterioration will always appear, since the supercritical flow will finally develop into a filmboiling-like state. So heat transfer deterioration should be taken seriously in the design and safe operation of vaporizer PCHE. The study of this work clarified the local heat transfer and flow feature of supercritical methane in microchannel and contributed to the deep understanding of supercritical methane flow of the vaporization process in PCHE.

Cobalt supported on CNTs-covered γ-and nano-structured alumina catalysts utilized for wax selective Fischer-Tropsch synthesis

Cobalt supported on carbon nanotubes （CNTs）-covered alumina has been recently developed and successfully utilized as a catalyst in Fischer-Tropsch synthesis （FTS）. Problems associated with shaping of Co/CNTs into extrudates or pellets as well as catalyst attrition rendered these materials unfavorable for industrial applications. In this investigation regular γ- and nano-structured （N-S） alumina as well as CNTs-covered regular γ- and N-S-alumina supports were impregnated by cobalt nitrate solution to make new cobalt-based catalysts which were also promoted by Ru. The catalysts were characterized and tested in a micro reactor to evaluate their applicability in FTS. γ-Al2O3 was prepared by calcination of bohemite and N-S-Al2O3 was prepared by sol-gel method using aluminum chloride as starting material. Catalyst evaluations indicated that N-S-Al2O3 was superior to regular γ-Al2O3 and that CNTs-covered alumina supports were favored over non-covered ones in terms of activity and heavy hydrocarbon selectivity. These were justified by porosimetric characteristics of the catalysts and existence of CNTs points of view. CNTs-covered catalysts also showed higher wax selectivity and better resistance to deactivation. Furthermore, TPR analysis indicated that the cobalt aluminate phase, which is responsible for the permanent deactivation of alumina supported Co-based catalysts, did not form on alumina supported Co-based catalysts covered with CNTs due to weaker interactions between cobalt and alumina.

Deposition mechanism of nano-structured single-layered C_(36) film on a diamond (100) crystal plane

The Brenner-LJ potential is adopted to describe the interaction between C36 clusters and diamond surface, and the deposition mechanism of multi-C36 clusters on the diamond surface is also studied by using the method of molecular dynamics simulation. The simulation results show that the competition effects of two interactions, i.e. the interaction between cluster and cluster and the interaction between cluster and crystal plane, are studied, and then the influence of these competition effects on C36 cluster deposition is analysed. The finding is that when an incident energy is appropriately chosen, C36 clusters can be chemically adsorbed and deposited steadily on the diamond surface in the form of single-layer, and in the deposition process the multi-C36 clusters present a phenomenon of energy transmission. The experimental result shows that at a temperature of 300K, in order to deposit C36 clusters into a steady nanostructured single-layered film, the optimal incident energy is between 10 and 18 eV, if the incident energy is larger than 18 eV, the C36 clusters will be deposited into an island nano-structured film.

A Comparative Study on the Milling Speed for the Synthesis of Nano-Structured Al 6063 Alloy Powder by Mechanical Alloying

The present article reports on characterization studies performed on amorphized nanostructured Al 6063 alloy powder synthesized by mechanical alloying (MA). The as-milled powder was characterized by X-ray diffraction (XRD) for investigating the development of crystallite nature and determining the different phases of the materials present, scanning electron microscope (SEM) was used for in depth morphological study and High Resolution-transmission electron microscope (HR-TEM) was employed to ensure the development of a nano-structured nature of the Al 6063 matrix. In the present work alloyed powder was milled for 20 h and 40 h at 300 rpm;and 20 h at 700 rpm in a hardened stainless steel medium. Using Williamson-Hall equation;crystallite size, lattice strain and lattice parameter of Al 6063 nanostructure alloy powder was estimated with broadening of XRD peaks. XRD results showed that the crystallite size of Al 6063 alloy powder reached 32 and 53 nm after 20 h at 700 rpm and 40 h at 300 rpm respectively.

Micro-CT分析跟骨内骨小梁分布及结构特征

背景:跟骨位于足的后下部,受力较大。跟骨外形复杂且不规则,外周有较薄的皮质骨包绕,内部充满大量的骨小梁,探讨骨小梁的微观结构、走行及分布特征有助于提高对跟骨骨折的认识。目的:采用微计算机断层扫描仪(Micro-CT)扫描跟骨标本获得其影像资料,对其内部骨小梁结构进行分析,探讨跟骨内骨小梁的形态、分布及结构特征。方法:采用Micro-CT连续扫描干燥成人跟骨标本,扫描后获得影像图像,将其以DICOM格式存储。导入影像资料到Hiscan Analyzer软件,显示清晰完整的成人跟骨矢状面、冠状面、水平面的图像,逐层观察骨小梁的走行,依据骨小梁走行特点将跟骨矢状面分为6个部分,在以7 mm为标准的相同厚度下,每个部分选择1个49 mm2等面积的兴趣区,三维重建后获得跟骨及骨小梁的立体微观结构,二值化后运用软件计算感兴趣区域内骨小梁的体积分数、表面密度、骨小梁厚度、骨小梁间隙和骨小梁数量参数。结果与结论:①跟骨表面皮质层很薄,内部充满大量骨松质,在Gissane角的骨皮质明显增厚;②跟骨上部的骨小梁体积分数大于跟骨下部前端、中和三角区、跟骨下后部、跟骨结节部、跟骨底部,跟骨结节部的骨小梁体积分数大于跟骨下部前端、中和三角区、跟骨下后部、跟骨底部;跟骨结节部的骨小梁表面密度大于跟骨下部前端、中和三角区、跟骨底部,跟骨上部、跟骨下后部的骨小梁表面密度大于中和三角区;跟骨上部的骨小梁厚度大于跟骨结节部;中和三角区的骨小梁间隙大于跟骨上部、跟骨结节部;跟骨结节部的骨小梁数量大于中和三角区;③中和三角区主要分布杆状骨小梁,骨小梁表面密度最小、体积分数较小、骨小梁间隙最大;该部位骨质较疏松,受到高冲击力时抗压缩能力差,骨小梁最先发生断裂,是易发生骨折的部位。

Enhancing Mechanical Stability of Nano-Structured Anti-Reflection Coatings

Periodic Nanostructured anti-reflection coatings (NALs) are a promising option for enhancing transmission of coherent light without inducing scattering. We’ve found that reducing the height of NALs below a critical value to enhance mechanical stability can highly reduce the transmission efficiency. Here, using Rigorous Couples Wave Analysis (RCWA), we find the minimum height for over 99% transmission and effect of height on transmission bandwidth. Then, during a one-step plasma etching, two samples with different heights have been generated and their efficiency is evaluated using RCWA.

The 18.3% Silicon Solar Cells with Nano-Structured Surface and Rear Emitter

A nano-structured surface is formed on the pyramid structure of n-type silicon solar cells by size-controlled silver nano-particle assisted etching. Such a nano-structure creates a front average weighted reflectance of less than 2.5% in the 300-1200nm range due to the broadband reflection suppression. The sodium hydroxide is used to obtain the low-area surface by post-etching the nano-structure, thus the severe carrier recombination associated with the nano-structured surface could be reduced. After emitter forming, screen printing and firing by means of the industrial fabrication protocol, an 18.3%-efficient nano-structured silicon solar cell with rear emitter is fabricated. The process of fabricating the solar cells matches well with industrial manufacture and shows promising prospects.