MHPPs （micro hydro power plants） have become prominent in hydropower plants as a solution to provide the energy demands of the grid. In this study, a new hybrid renewable energy based DC excitation system for synchr...MHPPs （micro hydro power plants） have become prominent in hydropower plants as a solution to provide the energy demands of the grid. In this study, a new hybrid renewable energy based DC excitation system for synchronous generator in the developed MHPP system is introduced. Proposed hybrid DC excitation system consists of solar ＆ hydrogen energy based power generating systems. Hybrid renewable energy based system is used for the excitation of the synchronous generator in the MHPP test system. The renewables are used as a secondary energy source to provide the excitation current to a synchronous generator that generates energy in MHPP. A PV （photovoltaic） array is used as the main source of excitation, and a FC （fuel cell） stack is used for DC excitation in the lack of sunshine. In the experimental setup, an electrical control card is developed, and a microcontroller is used to perform the proposed excitation system. All experimental results obtained from 5 kW rated power MHHP test system. Experimental results show that, the proposed method provides the continuous excitation current, and the operation of the synchronous generator is uninterrupted. The proposed method is also practical and easily implemented for MHPP systems.展开更多
A low-power complementary metal oxide semiconductor（CMOS） operational amplifier （op-amp） for real-time signal processing of micro air vehicle （MAV） is designed in this paper.Traditional folded cascode architectu...A low-power complementary metal oxide semiconductor（CMOS） operational amplifier （op-amp） for real-time signal processing of micro air vehicle （MAV） is designed in this paper.Traditional folded cascode architecture with positive channel metal oxide semiconductor（PMOS） differential input transistors and sub-threshold technology are applied under the low supply voltage.Simulation results show that this amplifier has significantly low power,while maintaining almost the same gain,bandwidth and other key performances.The power required is only 0.12 mW,which is applicable to low-power and low-voltage real-time signal acquisition and processing system.展开更多
The state of Cameroon, faced with the situation the electricity deficits, is promoting the development of renewable energies in general and to meet rural electrification needs in particular. The purpose of this work i...The state of Cameroon, faced with the situation the electricity deficits, is promoting the development of renewable energies in general and to meet rural electrification needs in particular. The purpose of this work is to study the feasibility of the MHP of Batcheu, to show its contribution to sustainable development in this locality and to prove that it is a profitable project. After study, it appears that the waterfall of Batcheu is favourable to the establishment of a MHP with an installed power of 260 kW with an operating diagram corresponding to a Francis turbine. Given that it is a renewable energy that can supply more than 800 households in rural areas, its contribution to sustainable development is obvious. Its investment cost is estimated at 171,465,396 FCFA. It is a profitable project with a payback time of 7 years and 2 months.展开更多
The differential pricing for peak hours encourages industrial consumers to look for independent power supplies for the period from 19 to 22 hours. This paper presents a study to identify the optimal solution for a rec...The differential pricing for peak hours encourages industrial consumers to look for independent power supplies for the period from 19 to 22 hours. This paper presents a study to identify the optimal solution for a recycled paper mill that also intends to work in that period. The factory is located in Rio Grande do Sul, in southern Brazil, and considers the use of a diesel gen set, a micro hydro power plant and possibly PV modules. Two micro hydro power plants were considered in the study, an old plant to be renewed and another to be fully implemented. The software Homer was used as a tool to determine the most feasible combination of components considered in the study. The sale of surplus power to the energy system appears as a key to viability of alternatives that are not based solely on diesel generators. The optimal solution consists of a combination of diesel generators and micro hydro power plant, in one case, and only on hydroelectric power plant in another, with a significant penetration of PV modules if its cost is reduced to 12% of the current price, selling an amount of energy equal to that which is bought. The annual water availability in one of the sites requires diesel supplement, while the other, more abundant, this supplement is not necessary.展开更多
Micro-grid plays a vital role in fulfilling the increasing demand by using distributed renewable energy resources. Demand and response technique can be broadly classified under the setup DR deployed (e.g. ISO’s/RTO’...Micro-grid plays a vital role in fulfilling the increasing demand by using distributed renewable energy resources. Demand and response technique can be broadly classified under the setup DR deployed (e.g. ISO’s/RTO’s). Demand response program can be implemented to improve power system quality, reliability and increasing demand. In modern power industry, strategic player can take more benefit from more emphasized DR study in terms of social benefit (uninterrupted power supply to consumers) and economy. This paper proposes the distributed micro-grid control and implemented control setup implemented demand response algorithm, which provides better power system reliability. This paper presents contingencies control demand and response for micro-grid. The main advantage of implementation of demand and response algorithms in Micro-grids provides reliable power supplies to consumers. The proposed micro-grid TCP/IP setup provides a chance to respond the contingencies to recover the shed to active condition. Micro-grid controller implements demand and response algorithm reasonable for managing the demand of the load and intelligent load scheme in case of blackout.展开更多
A digital arc welding power supply was designed with the advanced reduced instruction set computer machine （ARM） and embedded real-time multi-task operating system micro C/OS- Ⅱ. The ARM, with its powerful calculat...A digital arc welding power supply was designed with the advanced reduced instruction set computer machine （ARM） and embedded real-time multi-task operating system micro C/OS- Ⅱ. The ARM, with its powerful calculating speed and complete peripheral equipments, is very suitable to work as the controller of the digital power supply. The micro C/OS- Ⅱ transplanted in ARM, helps to improve the respondent speed against various welding signals, as well as the reliability of the controlling software. The welding process consists of nine tasks. The tasks of great significance on reliability of the welder, for example, the A/D conversion of current and voltage, enjoy top priority. To avoid simultaneous-sharing on A/D converter and LCD module, two semaphores are introduced in to ensure the smooth performance of the welding power supply. Proven by experiments ,the ARM and the micro C/OS- Ⅱ can greatly improve both the respondent speed and the reliability of the digital welder.展开更多
A micro direct methanol fuel cell （μDMFC） using MEMS technology is reported. The prototype features a unique 3D air-breathing cathode structure fabricated using KOH etching and double-side lithography. The optimiza...A micro direct methanol fuel cell （μDMFC） using MEMS technology is reported. The prototype features a unique 3D air-breathing cathode structure fabricated using KOH etching and double-side lithography. The optimization of the MEMS fabrication process is analyzed. The experimental results show the prototype generates a maximum power density of 2.52mW/cm^2 at room temperature. This performance is better than the published resuits of other silicon-based passive μDMFCs. Moreover,it is comparable with that of our previous active μDMFCs which require an external pump, certificating the feasibility of this new configuration.展开更多
随着新型电力系统建设持续推进,直流微电网将成为配电网的重要组成部分。直流微电网接入交流负载时,振荡型功率会进入直流系统,影响分布式储能系统功率分配。为此,给出了储能系统功率分配综合原则,并以此提出一种无互联通信网络的功率...随着新型电力系统建设持续推进,直流微电网将成为配电网的重要组成部分。直流微电网接入交流负载时,振荡型功率会进入直流系统,影响分布式储能系统功率分配。为此,给出了储能系统功率分配综合原则,并以此提出一种无互联通信网络的功率分配方法。该方法以荷电状态作为“信息载体”,各储能单元仅需本地荷电状态(state of charge,SOC)信息即可完成自适应调整,在实现SOC均衡控制的同时,还能够让振荡型功率合理分配。此外,从等效输出阻抗的角度出发,对不同控制算法的分配效果展开了详细的分析讨论,表明了所提控制算法可以满足综合原则的要求。最后,通过实验验证了所提分布式储能控制策略的有效性。展开更多
The Tsinghua 1 Micro satellite, the first satellite made by Tsinghua University, was launched in 2000. The power system of the Tsinghua 1 Micro satellite is one of the most important subsystems. It provides all...The Tsinghua 1 Micro satellite, the first satellite made by Tsinghua University, was launched in 2000. The power system of the Tsinghua 1 Micro satellite is one of the most important subsystems. It provides all the power for the satellite platform and the payloads. The power system design includes the regulation, protection and distribution of a 4×35 W solar array and 7 Ah NiCd batteries. This subsystem essentially offers two buses: an unregulated 14 V bus and a regulated 5 V bus. All distributed power lines to the users are protected by current tripping switches. In addition, some essential loads, such as the tele command system, are supplied through fuses. The Tsinghua 1 Micro satellite power system provides an efficient, flexible, reliable, and cost effective solution for small satellites in low earth orbit. A better maximum power point tracking method has been used to increase reliability margins and to increase the efficiency of the power system. The power system reliability was evaluated using several different tests, such as the power board test, the assembly integrate test (AIT), the electromagnetic compatibility (EMC) test and the thermal vacuum test (TVT).展开更多
文章以风-光-柴-储系统为研究对象,为了研究新能源出力不确定性对该系统的影响,提出了一种新能源出力复合预测模型。为提高风-光-柴-储系统运行的经济性、环保性和安全性,提出了考虑新能源出力不确定性的风-光-柴-储系统调度模型,并采...文章以风-光-柴-储系统为研究对象,为了研究新能源出力不确定性对该系统的影响,提出了一种新能源出力复合预测模型。为提高风-光-柴-储系统运行的经济性、环保性和安全性,提出了考虑新能源出力不确定性的风-光-柴-储系统调度模型,并采用了带有Monte Carlo模拟的遗传算法对模型进行求解。文章采用了负荷缺失率(load loss rate,LLR)和置信概率对系统的安全性进行评价,并分析了其对系统调度结果的影响。仿真结果表明,文中所提出的考虑新能源出力不确定性的风-光-柴-储系统调度模型,可以降低新能源出力不确定性对系统的影响,且该方法可以有效地平衡系统的经济性和安全性。展开更多
文摘MHPPs （micro hydro power plants） have become prominent in hydropower plants as a solution to provide the energy demands of the grid. In this study, a new hybrid renewable energy based DC excitation system for synchronous generator in the developed MHPP system is introduced. Proposed hybrid DC excitation system consists of solar ＆ hydrogen energy based power generating systems. Hybrid renewable energy based system is used for the excitation of the synchronous generator in the MHPP test system. The renewables are used as a secondary energy source to provide the excitation current to a synchronous generator that generates energy in MHPP. A PV （photovoltaic） array is used as the main source of excitation, and a FC （fuel cell） stack is used for DC excitation in the lack of sunshine. In the experimental setup, an electrical control card is developed, and a microcontroller is used to perform the proposed excitation system. All experimental results obtained from 5 kW rated power MHHP test system. Experimental results show that, the proposed method provides the continuous excitation current, and the operation of the synchronous generator is uninterrupted. The proposed method is also practical and easily implemented for MHPP systems.
基金Sponsored by the National Natural Science Foundation of China (60843005)the Basic Research Foundation of Beijing Institute of Technology(20070142018)
文摘A low-power complementary metal oxide semiconductor（CMOS） operational amplifier （op-amp） for real-time signal processing of micro air vehicle （MAV） is designed in this paper.Traditional folded cascode architecture with positive channel metal oxide semiconductor（PMOS） differential input transistors and sub-threshold technology are applied under the low supply voltage.Simulation results show that this amplifier has significantly low power,while maintaining almost the same gain,bandwidth and other key performances.The power required is only 0.12 mW,which is applicable to low-power and low-voltage real-time signal acquisition and processing system.
文摘The state of Cameroon, faced with the situation the electricity deficits, is promoting the development of renewable energies in general and to meet rural electrification needs in particular. The purpose of this work is to study the feasibility of the MHP of Batcheu, to show its contribution to sustainable development in this locality and to prove that it is a profitable project. After study, it appears that the waterfall of Batcheu is favourable to the establishment of a MHP with an installed power of 260 kW with an operating diagram corresponding to a Francis turbine. Given that it is a renewable energy that can supply more than 800 households in rural areas, its contribution to sustainable development is obvious. Its investment cost is estimated at 171,465,396 FCFA. It is a profitable project with a payback time of 7 years and 2 months.
文摘The differential pricing for peak hours encourages industrial consumers to look for independent power supplies for the period from 19 to 22 hours. This paper presents a study to identify the optimal solution for a recycled paper mill that also intends to work in that period. The factory is located in Rio Grande do Sul, in southern Brazil, and considers the use of a diesel gen set, a micro hydro power plant and possibly PV modules. Two micro hydro power plants were considered in the study, an old plant to be renewed and another to be fully implemented. The software Homer was used as a tool to determine the most feasible combination of components considered in the study. The sale of surplus power to the energy system appears as a key to viability of alternatives that are not based solely on diesel generators. The optimal solution consists of a combination of diesel generators and micro hydro power plant, in one case, and only on hydroelectric power plant in another, with a significant penetration of PV modules if its cost is reduced to 12% of the current price, selling an amount of energy equal to that which is bought. The annual water availability in one of the sites requires diesel supplement, while the other, more abundant, this supplement is not necessary.
文摘Micro-grid plays a vital role in fulfilling the increasing demand by using distributed renewable energy resources. Demand and response technique can be broadly classified under the setup DR deployed (e.g. ISO’s/RTO’s). Demand response program can be implemented to improve power system quality, reliability and increasing demand. In modern power industry, strategic player can take more benefit from more emphasized DR study in terms of social benefit (uninterrupted power supply to consumers) and economy. This paper proposes the distributed micro-grid control and implemented control setup implemented demand response algorithm, which provides better power system reliability. This paper presents contingencies control demand and response for micro-grid. The main advantage of implementation of demand and response algorithms in Micro-grids provides reliable power supplies to consumers. The proposed micro-grid TCP/IP setup provides a chance to respond the contingencies to recover the shed to active condition. Micro-grid controller implements demand and response algorithm reasonable for managing the demand of the load and intelligent load scheme in case of blackout.
基金Supported by the National Natural Science Foundation of China under Grant No 50575074by the Scientific and TechnologicalProject of Guangdong Province, China, under Grant No 2003A1040310
文摘A digital arc welding power supply was designed with the advanced reduced instruction set computer machine （ARM） and embedded real-time multi-task operating system micro C/OS- Ⅱ. The ARM, with its powerful calculating speed and complete peripheral equipments, is very suitable to work as the controller of the digital power supply. The micro C/OS- Ⅱ transplanted in ARM, helps to improve the respondent speed against various welding signals, as well as the reliability of the controlling software. The welding process consists of nine tasks. The tasks of great significance on reliability of the welder, for example, the A/D conversion of current and voltage, enjoy top priority. To avoid simultaneous-sharing on A/D converter and LCD module, two semaphores are introduced in to ensure the smooth performance of the welding power supply. Proven by experiments ,the ARM and the micro C/OS- Ⅱ can greatly improve both the respondent speed and the reliability of the digital welder.
文摘A micro direct methanol fuel cell （μDMFC） using MEMS technology is reported. The prototype features a unique 3D air-breathing cathode structure fabricated using KOH etching and double-side lithography. The optimization of the MEMS fabrication process is analyzed. The experimental results show the prototype generates a maximum power density of 2.52mW/cm^2 at room temperature. This performance is better than the published resuits of other silicon-based passive μDMFCs. Moreover,it is comparable with that of our previous active μDMFCs which require an external pump, certificating the feasibility of this new configuration.
文摘随着新型电力系统建设持续推进,直流微电网将成为配电网的重要组成部分。直流微电网接入交流负载时,振荡型功率会进入直流系统,影响分布式储能系统功率分配。为此,给出了储能系统功率分配综合原则,并以此提出一种无互联通信网络的功率分配方法。该方法以荷电状态作为“信息载体”,各储能单元仅需本地荷电状态(state of charge,SOC)信息即可完成自适应调整,在实现SOC均衡控制的同时,还能够让振荡型功率合理分配。此外,从等效输出阻抗的角度出发,对不同控制算法的分配效果展开了详细的分析讨论,表明了所提控制算法可以满足综合原则的要求。最后,通过实验验证了所提分布式储能控制策略的有效性。
文摘The Tsinghua 1 Micro satellite, the first satellite made by Tsinghua University, was launched in 2000. The power system of the Tsinghua 1 Micro satellite is one of the most important subsystems. It provides all the power for the satellite platform and the payloads. The power system design includes the regulation, protection and distribution of a 4×35 W solar array and 7 Ah NiCd batteries. This subsystem essentially offers two buses: an unregulated 14 V bus and a regulated 5 V bus. All distributed power lines to the users are protected by current tripping switches. In addition, some essential loads, such as the tele command system, are supplied through fuses. The Tsinghua 1 Micro satellite power system provides an efficient, flexible, reliable, and cost effective solution for small satellites in low earth orbit. A better maximum power point tracking method has been used to increase reliability margins and to increase the efficiency of the power system. The power system reliability was evaluated using several different tests, such as the power board test, the assembly integrate test (AIT), the electromagnetic compatibility (EMC) test and the thermal vacuum test (TVT).
文摘文章以风-光-柴-储系统为研究对象,为了研究新能源出力不确定性对该系统的影响,提出了一种新能源出力复合预测模型。为提高风-光-柴-储系统运行的经济性、环保性和安全性,提出了考虑新能源出力不确定性的风-光-柴-储系统调度模型,并采用了带有Monte Carlo模拟的遗传算法对模型进行求解。文章采用了负荷缺失率(load loss rate,LLR)和置信概率对系统的安全性进行评价,并分析了其对系统调度结果的影响。仿真结果表明,文中所提出的考虑新能源出力不确定性的风-光-柴-储系统调度模型,可以降低新能源出力不确定性对系统的影响,且该方法可以有效地平衡系统的经济性和安全性。
