Effect of Micro-electrolysis and Micro-nano Bubbles Coupled with Peroxymonosulfate Treatment of Rural Domestic Sewage

With the continuous deepening of rural revitalization strategy and the increasingly strict sewage discharge standards,rural domestic sewage treatment technology is facing higher challenges and requirements.The combined process of micro-electrolysis+micro-nano bubbles coupled with peroxymonosulfate was constructed in this study,and the treatment effect and application value of this technology were explored with the actual rural domestic sewage as the treatment object.The experimental results showed that under the conditions of HRT of 120 min,PMS dosage of 0.15 mmol/L,pH=7,MBs air intake of 15 ml/min,current intensity of 15 A,and Fe/C mass ratio of 1:1,the removal rates of COD,ammonia nitrogen and total phosphorus can reach 88.55%,77.18%and 74.67%,respectively.Under the condition that the pH value of sewage was not adjusted,the non-biochemical simultaneous decarbonization,denitrification and phosphorus removal of rural domestic sewage can be achieved by micro-electrolysis and micro-nano bubbles coupled with peroxymonosulfate.The concentrations of effluent COD,ammonia nitrogen and total phosphorus met the requirements of the first level standard of the Discharge Standard of Water Pollutants for Rural Domestic Sewage Treatment Facilities(DB45T2413-2021).And the comprehensive operating cost was about 1.15 yuan/m 3.

An internal circulation iron-carbon micro-electrolysis reactor for aniline wastewater treatment:Parameter optimization,degradation pathways and mechanism

Aniline is a vital industrial raw material.However,highly-toxic aniline wastewater usually deteriorated effluent quality,posed a threat to human health and ecosystem safety.Therefore,this study reported a novel internal circulation iron-carbon micro-electrolysis(ICE)reactor to treat aniline wastewater.The effects of reaction time,pH,aeration rate and iron-carbon(Fe/C)ratio on the removal rate of aniline and the chemical oxygen demand were investigated using single-factor experiments.This process exhibited high aniline degradation performance of approximately 99.86% under optimal operating conditions(reaction time=20 min,pH=3,aeration rate=0.5 m3·h^(-1),and Fe/C=1:2).Based on the experimental results,the response surface method was applied to optimize the aniline removal rate.The Box–Behnken method was used to obtain the interaction effects of three main factors.The result showed that the reaction time had a dominant effect on the removal rate of aniline.The highest aniline removal rate was obtained at pH of 2,aeration rate of 0.5 m^(3)·h^(-1)and reaction time of 30 min.Under optional experimental conditions,the aniline content of effluent was reduced to 3 mg·L^(-1)and the removal rate was as high as 98.24%,within the 95% confidence interval(97.84%-99.32%)of the predicted values.The solution was treated and the reaction intermediates were identified by high-performance liquid chromatography,ultraviolet-visible spectroscopy,Fourier-transform infrared spectroscopy,gas chromatography-mass spectrometry,and ion chromatography.The main intermediates were phenol,benzoquinone,and carboxylic acid.These were used to propose the potential mechanism of aniline degradation in the ICE reactor.The results obtained in this study provide optimized conditions for the treatment of industrial wastewater containing aniline and can strengthen the understanding of the degradation mechanism of iron-carbon micro-electrolysis.

Computer vision-aided DEM study on the compaction characteristics of graded subgrade filler considering realistic coarse particle shapes

The compaction quality of subgrade filler strongly affects subgrade settlement.The main objective of this research is to analyze the macro-and micro-mechanical compaction characteristics of subgrade filler based on the real shape of coarse particles.First,an improved Viola-Jones algorithm is employed to establish a digitalized 2D particle database for coarse particle shape evaluation and discrete modeling purposes of subgrade filler.Shape indexes of 2D subgrade filler are then computed and statistically analyzed.Finally,numerical simulations are performed to quantitatively investigate the effects of the aspect ratio(AR)and interparticle friction coefficient(μ)on the macro-and micro-mechanical compaction characteristics of subgrade filler based on the discrete element method(DEM).The results show that with the increasing AR,the coarse particles are narrower,leading to the increasing movement of fine particles during compaction,which indicates that it is difficult for slender coarse particles to inhibit the migration of fine particles.Moreover,the average displacement of particles is strongly influenced by the AR,indicating that their occlusion under power relies on particle shapes.The dis-placement and velocity of fine particles are much greater than those of the coarse particles,which shows that compaction is primarily a migration of fine particles.Under the cyclic load,the interparticle friction coefficientμhas little effect on the internal structure of the sample;under the quasi-static loads,however,the increase inμwill lead to a significant increase in the porosity of the sample.This study could not only provide a novel approach to investigate the compaction mechanism but also establish a new theoretical basis for the evaluation of intelligent subgrade compaction.

Effect of brazing temperature on microstructure and tensile strength ofγ-TiAl joint vacuum brazed with micro-nano Ti−Cu−Ni−Nb−Al−Hf filler

A novel micro-nano Ti−10Cu−10Ni−8Al−8Nb−4Zr−1.5Hf filler was used to vacuum braze Ti−47Al−2Nb−2Cr−0.15B alloy at 1160−1220℃ for 30 min.The interfacial microstructure and formation mechanism of TiAl joints and the relationships among brazing temperature,interfacial microstructure and joint strength were emphatically investigated.Results show that the TiAl joints brazed at 1160 and 1180℃ possess three interfacial layers and mainly consist of α_(2)-Ti_(3)Al,τ_(3)-Al_(3)NiTi_(2) and Ti_(2)Ni,but the brazing seams are no longer layered and Ti_(2)Ni is completely replaced by the uniformly distributed τ_(3)-Al_(3)NiTi_(2) at 1200 and 1220℃ due to the destruction of α_(2)-Ti_(3)Al barrier layer.This transformation at 1200℃ obviously improves the tensile strength of the joint and obtains a maximum of 343 MPa.Notably,the outward diffusion of Al atoms from the dissolution of TiAl substrate dominates the microstructure evolution and tensile strength of the TiAl joint at different brazing temperatures.

Influence of filler characteristics on particle removal in fluid catalytic cracking slurry under an alternating electric field

The characteristics of the packing material under an alternating electric field are an important factor in the removal of FCCS particles.In this study,the electric field distribution of a separation unit consisting of packed spheres under an alternating electric field is simulated,and the movement mechanism of catalyst particles is analysed.An"effective contact point"model is derived to predict the adsorption of filler contact points on catalyst particles under the alternating electric field,and the model is validated by simulations and experiments.The numerical calculation and experimental results indicate that the electrical properties of the filler spheres,the filler angleθ,and the frequency f of the alternating electric field affect the adsorption of catalyst particles.As the frequency of the electric field increases,the particle removal efficiency of the high-conductivity filler(silicon carbide)increases and then settles,and the separation efficiency of the low-conductivity filler(glass,zirconia)is not sensitive to the change in electric field frequency.

Basic Characteristics of an Appropriate Waste Fillers for Solvent Free and Water-Borne Industrial Polymer Floors and Their Utilization

Recently the manufacture of epoxy coating and flooring materials begun to be under strong pressure to use more environmentally friendly raw materials in its composition.First tendency to reduce of solvents and diluents contained in the materials appeared at the end of 90´s.This situation was supported by the Council of Europe in 2004 to reduce VOC emissions to zero till 2020.Solvent materials were thus largely replaced by solvent free materials from which the volatile substances are not released into the air.But pressure continued to increase,and over the past decade began to take centre stage water-based epoxy.On the Czech market solvent based material is still occasionally used,but predominant are solvent free materials.There are no commonly used materials containing wastes as fillers in new water-borne and solvent-free epoxy materials.Characteristics identification of the waste material as a potential filler is a set of properties that determine the limits of secondary raw materials or waste as a filler.This paper describes the basic characteristics which must be selected to meet the requirements,to affect negatively the workability,sedimentation,properties and behavior of the final floor system.Some materials must comply with special requirements,such as resistance to chemicals,etc.Next part of paper talks about utilization of polymer floors and their mechanical properties.

Degradation of organic wastewater containing Cu-EDTA by Fe-C micro-electrolysis

In order to break the complex bonds and treat the organic wastewater containing heavy metal,such as Cu-EDTA solution,a novel process of Fe-C micro-electrolysis was proposed.Based on the principle of iron-carbon micro-electrolysis reaction,-OH radicals which were generated under the acidic aerobic condition during the micro-electrolysis process attacked to the organic groups of coordination compounds,which resulted in complex bonds breaking.Therefore copper（Ⅱ） ions were removed via nascent gelatinous ferric hydroxide and ferrous hydroxide,and EDTA was degraded by-OH radicals.Effects of pH value,temperature,electrolysis time and mass ratio of Fe to C on residual concentrations of total organic carbon（TOC） and Cu（Ⅱ） were studied.The mechanism of Fe-C micro-electrolysis was investigated and verified by analyzing micrographs of scanning electron microscopy（SEM）,energy dispersive analysis（EDS） and Fourier transform infrared spectrometry（FTIR）.The removal efficiency is optimal at pH value of 2.0,temperature of 25 °C,the mass ratio Fe to C of 0.02,and reaction time of 60 min.Under above conditions,the concentration of TOC decreases from 200 mg/L to 40.66 mg/L and the residual concentration of Cu（Ⅱ） decreases from initial 60 mg/L to 1.718 mg/L.

Effective removal of Sb(V)from aqueous solutions by micro-electrolysis with composite scrap iron-manganese as filler

Micro-electrolysis(ME)technology is investigated for improving the efficiency of removal of pentavalent antimony(Sb(V))from the environment.In this study,an ME system composed of scrap iron filings,waste manganese fillings,and activated carbon(Fe-Mn-C ME)was used to efficiently remove Sb(V).The results proved that,compared with conventional iron-carbon micro-electrolysis(Fe-C ME),Fe-Mn-C ME significantly enhances the removal rate of Sb(V)when the hydraulic retention time is 10–24 h.The Fe-Mn flocs produced by this system were analyzed using X-ray diffraction(XRD),energy-dispersive X-ray spectroscopy(EDS),X-ray photoelectron spectroscopy(XPS),and Brunauer-Emmett-Teller(BET)surface area analysis,which revealed that the flocs were mostly Mn-substituted FeOOH and had a relatively larger specific surface area,providing better adsorption performance.Furthermore,it was found that the removal rate of Sb(V)decreased as the iron-carbon mass ratio increased,while it first increased and then decreased as the manganese content increased.The reduction of Fe(III)was accelerated with an increase in the addition of manganese,leading to an increase in the concentration of Fe(II).The electron transfer and the formation of Fe(II)were facilitated by the potential difference between manganese and carbon,as well as by the formation of microcells between iron and manganese,which improved the reduction ability of Sb(V).From our thorough investigation and research,this is the first report that has proposed Fe-Mn-C ME for removing antimony.It provides a novel approach and technological support for removing Sb(V)efficiently.

Treatment of naphthalene derivatives with iron-carbon micro-electrolysis

The degradation of five naphthalene derivatives in the simulated wastewater was investigated using the iron-carbon micro-electrolysis method.The optimal initial pH of solution and adsorption of iron-carbon and removal efficiency of the total organic carbon(TOC)were investigated.The results show that the removal efficiency of the naphthalene derivatives can reach 48.9%?92.6% and the removal efficiency of TOC is 42.8%?78.0% for the simulated wastewater with 200 mg/L naphthalene derivatives at optimal pH of 2.0?2.5 after 120 min treatment.The degradation of five naphthalene derivatives with the micro-electrolysis shows the apparent first-order kinetics and the order of removal efficiency of the naphthalene derivatives is sodium 2-naphthalenesulfonate,2-naphthol,2,7-dihydroxynaphthalene,1-naphthamine,1-naphthol-8-sulfonic acid in turn.It is illustrated that the substituents of the naphthalene ring can affect the removal efficiency of naphthalene due to their electron-withdrawing or electron-donating ability.

Micro-electrolysis technology for industrial wastewater treatment

Experiments were conducted to study the role of micro-electrolysis in removing chromaticity and COD and improving the biodegradability of wastewater from pharmaceutical, dye-printing and papermaking plants. Results showed that the use of micro-electrolysis technology could remove more than 90% of chromaticity and more than 50% of COD and greatly improved the biodegradability of pharmaceutical wastewater. Lower initial pH could be advantageous to the removal of chromaticity. A retention time of 30 minutes was recommended for the process design of micro-electrolysis. For the use of micro-electrolysis in treatment of dye-printing wastewater, the removal rates of both chromaticity and COD were increased from neutral condition to acid condition for disperse blue wastewater; more than 90% of chromaticity and more than 50% of COD could be removed in neutral condition for vital red wastewater.

Experimental study on micro-electrolysis technology for pharmaceutical wastewater treatment

Experiments were conducted to study the role of micro-electrolysis in removing chromaticity and COD and improving the biodegradability of pharmaceutical wastewater. The results showed that the use of micro-electrolysis technology could remove more than 90% of chromaticity and more than 50% of COD and greatly improved the biodegradability of pharmaceutical wastewater. Lower initial pH could be advantageous to the removal of chromaticity. A retention time of 30 minutes was recommended for the process design of micro-electrolysis.

Treatment of chitin-producing wastewater by micro-electrolysis-contact oxidization

The technique of micro-electrolysis-contact oxidization was exploited to treat chitin-producing wastewater. Results showed that Fe-C micro-electrolysis can remove about 30% CODcr, raise pH from 0.7 to 5.5. The CODcr removal efficiency by biochemical process can be more than 80%. During a half year抯 operation, the whole system worked very stably and had good results, as proved by the fact that every quality indicator of effluent met the expected discharge stan-dards; which means that chitin wastewater can be treated by the technique of micro-electrolysis, contact oxidization.

Optimization of the N2 generation selectivity in aqueous nitrate reduction using internal circulation micro-electrolysis

The reduction of nitrate using internal circulation micro-electrolysis te chnology(ICE)was investigated.The effect of the reaction time,initial pH,Fe/C ratio,and aeration rate on the nitrate reduction was investigated using a single factor experiment.Based on the results of the single factor experiment,a response surface methodology(RSM)was applied to optimize the N2 generation selectivity.The effects and interactions of three independent variables were estimated using a Box-Behnken design.Using the RSM analysis,a quadratic polynomial model with optimal conditions at pH=8.8,Fe/C=1:1,and an aeration rate of 30 L·min-1 was developed by means of the regre ssion analysis of the experimental data.Using the RSM optimization,the optimal conditions yielded a N2 generation selectivity of 72.0%,which is in good agreement with experimental result(73.2%±0.5%)and falls within the 95%confidence interval(IC:66.8%-77.3%)of the model results.This indicates that the model obtained in this study effectively predicts the N2 generation selectivity for nitrate reduction by the ICE process,thus providing a theoretical basis for process design.

Nitrogen removal efficiency of iron-carbon micro-electrolysis system treating high nitrate nitrogen organic pharmaceutical wastewater

The nitrate nitrogen removal efficiency of iron-carbon micro-electrolysis system was discussed in treating pharmaceutical wastewater with high nitrogen and refractory organic concentration. The results show that the granularity of fillings,pH,volume ratios of iron-carbon and gas-water,and HRT. have significant effects on the nitrogen removal efficiency of iron-carbon micro-electrolysis system. The iron-carbon micro-electrolysis system has a good removal efficiency of pharmaceutical wastewater with high nitrogen and refractory organic concentration when the influent TN,NH4+-N,NO3--N and BOD5/CODCr are 823 mg/L,30 mg/L,793 mg/L and 0.1,respectively,at the granularity of iron and carbon 0.425 mm,pH 3,iron-carbon ratio 3,gas-water ratio 5,HRT 1.5 h,and the removal rates of TN,NH4+-N and NO3--N achieve 51.5%,70% and 50.94%,respectively.

Structural parameter optimization for novel internal-loop iron–carbon micro-electrolysis reactors using computational fluid dynamics

It is generally recognized that internal-loop reactors are well-developed mass and heat-transfer multiphase flow reactors. However, the internal flow field in the internal-loop reactor is influenced by the structure parameter of the reactor, which has a great effect on the reaction efficiency. In this study, the computational fluid dynamics simulation method was used to determine the influence of reactor structure on flow field, and a volume-offluid model was employed to simulate the gas–liquid, two-phase flow of the internal-loop micro-electrolysis reactor. Hydrodynamic factors were optimized when the height-to-diameter ratio was 4:1, diameter ratio was9:1, draft-tube axial height was 90 mm. Three-dimensional simulations for the water distributor were carried out, and the results suggested that the optimal conditions are as follows: the number of water distribution pipes was four, and an inhomogeneous water distribution was used. According to the results of the simulation,the suitable structure can be used to achieve good fluid mechanical properties, such as the good liquid circulation velocity and gas holdup, which provides a good theoretical foundation for the application of the reactor.

Degradation of Nitrobenzene Wastewater via Iron/Carbon Micro-electrolysis Enhanced by Ultrasound Coupled with Hydrogen Peroxide

The zero valent iron/granular active carbon(ZVI/GAC) micro-electrolysis enhanced by ultrasound(US) coupled with hydrogen peroxide(H_2O_2) was investigated for the deep degradation of nitrobenzene-containing wastewater. The results of scanning electron microscopy-energy dispersive X-rays analysis(SEM-EDS) demonstrated that continuously accelerated regeneration of ZVI and GAC in situ by US could improve the process for converting nitrobenzene(NB) to aniline(AN). H_2O_2 was decomposed catalytically by the byproduct Fe^(2+) ions generated in the micro-electrolysis process to hydroxyl radicals and the organic pollutants in the wastewater were finally mineralized to CO2 and H2O. Effects of the ZVI dosage, the ZVI/GAC mass ratio, the initial pH value and the H_2O_2 dosage on the efficiency for degradation of NB were studied in these experiments. The optimal operating conditions covered a ZVI dosage of 15 g/L, a ZVI/GAC mass ratio of 1:2,an initial pH value of 3 and a H_2O_2 dosage of 4 mL. In this case, the NB removal efficiency reached 97.72% and the total organic carbon(TOC) removal efficiency reached 73.42% at a NB concentration of 300 mg/L. The reduction of NB by USZVI/GAC followed the pseudo-first-order kinetics model, and the pseudo-first-order rate constants were given at different initial pH values. The reaction intermediates such as AN, benzoquinonimine, p-benzoquinone, p-nitrophenol and other organic acids were detected and a probable pathway for NB degradation has been proposed.

The Critical Role of Fillers in Composite Polymer Electrolytes for Lithium Battery

With excellent energy densities and highly safe performance,solidstate lithium batteries(SSLBs)have been hailed as promising energy storage devices.Solid-state electrolyte is the core component of SSLBs and plays an essential role in the safety and electrochemical performance of the cells.Composite polymer electrolytes(CPEs)are considered as one of the most promising candidates among all solid-state electrolytes due to their excellent comprehensive performance.In this review,we briefly introduce the components of CPEs,such as the polymer matrix and the species of fillers,as well as the integration of fillers in the polymers.In particular,we focus on the two major obstacles that affect the development of CPEs:the low ionic conductivity of the electrolyte and high interfacial impedance.We provide insight into the factors influencing ionic conductivity,in terms of macroscopic and microscopic aspects,including the aggregated structure of the polymer,ion migration rate and carrier concentration.In addition,we also discuss the electrode-electrolyte interface and summarize methods for improving this interface.It is expected that this review will provide feasible solutions for modifying CPEs through further understanding of the ion conduction mechanism in CPEs and for improving the compatibility of the electrode-electrolyte interface.

Structure and Properties of PLA Composite Enhanced with Biomass Fillers from Herbaceous Plants

PLA composites containing biomass fillers from the three herbaceous plants such as reed,wheat stalk,and coco-nut fiber with length and diameter at the scale of several millimeters were prepared without using additives.The reinforcement effect on the properties of PLA/biomass filler composites is investigated.The research results show that the PLA/biomass filler composites exhibit good stiffness,flexural strength,and impact toughness.Among the three kinds of biomass fillers,reed reinforced PLA composites show optimal mechanical properties.When filled with 40%–50%reed,the flexural moduli of the composites are over 7000 MPa.Flexural strength retains at the same level of pure PLA.The notch impact strength reaches to 4.50±0.73 kJ/m^(2),which is 2.06 times higher than that of pure PLA.Furthermore,the introduction of biomass fillers increases the crystallization ability of PLA and does not increase the water absorption of the composites.This research demonstrated that PLA composites prepared with biomass fillers from the herbaceous plants(namely herb plastic composites,HPCs)is a material with good comprehensive mechanical properties while retaining the intrinsic particularity of biological sources.

In-depth analysis of the influence of bio-silica filler(Didymosphenia geminata frustules)on the properties of Mg matrix composites

A novel metal matrix composites(MMC)with Mg matrix reinforced with natural filler in the form of Didymosphenia geminata frustules(algae with distinctive siliceous shells)are presented in this work.Pulse plasma sintering(PPS)was used to manufacture Mg-based composites with 1,5 and 10 vol.%ceramic filler.As a reference,pure Mg was sintered.The results show that the addition of 1 vol.%Didymosphenia geminata frustules to the Mg matrix increases its corrosion resistance by supporting passivation reactions,and do not affect the morphology of L929 fibroblasts.Addition of 5 vol.%the filler does not cause cytotoxic effects,but it supports microgalvanic reactions leading to the greater corrosion rate.Higher content than 5 vol.%the filler causes significant microgalvanic corrosion,as well as increases cytotoxicity due to the greater micro-galvanic effect of the composites containing 10 and 15 vol.%diatoms.The results of contact angle measurements show the hydrophilic character of the investigated materials,with slightly increase in numerical values with addition of amount of ceramic reinforcement.The addition of Didymosphenia geminata frustules causes changes in a thermo-elastic properties such as mean apparent value of coefficient of thermal expansion(CTE)and thermal conductivity(λ).The addition of siliceous reinforcement resulted in a linear decrease of CTE and reduction in thermal conductivity over the entire temperature range.With the increasing addition of Didymosphenia geminata frustules,an increase in strength with a decrease in compressive strain is observed.In all composites an increase in microhardness was attained.The results clearly indicate that filler in the form of Didymosphenia geminata frustules may significantly change the most important properties of pure Mg,indicating its wide potential in the application of Mg-based composites with a special focus on biomedical use.

Phase field simulation of grain refinement in silver-based filler metal

Numerical simulation is one of the important auxiliary methods for studying materials-related problems. In this study, phase field simulation was employed to investigate the refinement behavior of BAg55CuZn-x B brazing alloys. Simulation and experimental studies were conducted for B contents ranging from 0 wt.% to 0.2 wt.%. The results demonstrated that the addition of 0.05 wt.% B in the brazing alloy leads to a significant refinement effect. As the B content increases, the grain size further reduces, and a refinement stagnation phenomenon occurs after exceeding 0.15 wt.%. The solidification process of brazing alloys with different B content was predicted by simulation, and the simulation results showed that with the increase of B content, the initial number of nucleation increased, and the radius of the dendrite tip decreased. The simulation results are in good agreement with the experimental findings, providing further evidence of the refining effect of the B element and the reliable predictive capability of the phase field model.