Recent progresses in the development of tubular segmented-in-series solid oxide fuel cells:Experimental and numerical study

Solid oxide fuel cells(SOFCs)have attracted a great deal of interest because they have the highest efficiency without using any noble metal as catalysts among all the fuel cell technologies.However,traditional SOFCs suffer from having a higher volume,current leakage,complex connections,and difficulty in gas sealing.To solve these problems,Rolls-Royce has fabricated a simple design by stacking cells in series on an insulating porous support,resulting in the tubular segmented-in-series solid oxide fuel cells(SIS-SOFCs),which achieved higher output voltage.This work systematically reviews recent advances in the structures,preparation methods,perform-ances,and stability of tubular SIS-SOFCs in experimental and numerical studies.Finally,the challenges and future development of tubular SIS-SOFCs are also discussed.The findings of this work can help guide the direction and inspire innovation of future development in this field.

Remediation of oily soil using acidic sophorolipids micro-emulsion

A sophorolipids(SLs)micro-emulsion in Winsor type Ⅰ form was used for crude oil contaminated soil washing treatment.The micro-emulsion shows higher oil removal rate than SLs aqueous solution and diesel oil.The type Ⅰ micro-emulsion with w(SLs)=6%,w(NaCl)=1%,w(diesel)=13.36% gave a high oil removal rate of 95.6% and the eluate remained in type Ⅰ state.The recovered oil showed lower viscosity,mainly caused by the entering of diesel from the micro-emulsion phase into the oil phase and the lower removal rate of the heavier components,such as the resin and asphaltene.The initial heavily saline-alkaline soil changed into mildly saline-alkaline state after washing treatment,favoring the germination and growth of plants,with ryegrass showing better germination and growth effect than alfalfa.The ryegrass showed good phytoremediation effect on the contaminated soil after SLs micro-emulsion washing.The combination process of SL micro-emulsion washing and ryegrass phytoremediation is prospective for oily soil treatment.

Nutrition impacts of non-solid cooking fuel adoption on under-five children in developing countries

This paper examines the nutrition impacts of using non-solid cooking fuel on under-five children in developing countries.We draw on data from more than 1.12 million children in 62 developing countries from the Demographic and Health Surveys(DHS).Results from both fixed effects(FE)and instrumental variable(IV)estimates show that using non-solid cooking fuel significantly improves the nutrition outcomes of under-five children.Compared with their peers from households mainly using solid fuel,children from households mainly using non-solid fuel exhibit a lower probability of experiencing stunting(by 5.9 percentage points)and being underweight(by 1.2 percentage points).Our further investigation provides evidence for several underlying mechanisms,such as improved indoor air quality,induced reduction in children’s respiratory symptoms,benefits on maternal health,and reduction in maternal time spent on fuel collection or cooking.Heterogenous analyses suggest that the nutrition benefits of using non-solid cooking fuel are more prominent among boys,children above three years old,and those from households of lower socioeconomic status,rural areas,and Southeast Asia.

From concept to commercialization:A review of tubular solid oxide fuel cell technology

The reduced sealing difficulty of tubular solid oxide fuel cells(SOFCs)makes the stacking of tubular cell groups relatively easy,and the thermal stress constraints during stack operation are smaller,which helps the stack to operate stably for a long time.The special design of tubular SOFC structures can completely solve the problem of high-temperature sealing,especially in the design of multiple single-cell series integrated into one tube,where each cell tube is equivalent to a small electric stack,with unique characteristics of high voltage and low current output,which can significantly reduce the ohmic polarization loss of tubular cells.This paper provides an overview of typical tubular SOFC structural designs both domestically and internationally.Based on the geometric structure of tubular SOFCs,they can be divided into bamboo tubes,bamboo flat tubes,single-section tubes,and single-section flat tube structures.Meanwhile,this article provides an overview of commonly used materials and preparation methods for tubular SOFCs,including commonly used materials and preparation methods for support and functional layers,as well as a comparison of commonly used preparation methods for microtubule SOFCs,It introduced the three most important parts of building a fuel cell stack:manifold,current collector,and ceramic adhesive,and also provided a detailed introduction to the power generation systems of different tubular SOFCs,Finally,the development prospects of tubular SOFCs were discussed.

Model reduction of fractional impedance spectra for time–frequency analysis of batteries, fuel cells, and supercapacitors

Joint time–frequency analysis is an emerging method for interpreting the underlying physics in fuel cells,batteries,and supercapacitors.To increase the reliability of time–frequency analysis,a theoretical correlation between frequency-domain stationary analysis and time-domain transient analysis is urgently required.The present work formularizes a thorough model reduction of fractional impedance spectra for electrochemical energy devices involving not only the model reduction from fractional-order models to integer-order models and from high-to low-order RC circuits but also insight into the evolution of the characteristic time constants during the whole reduction process.The following work has been carried out:(i)the model-reduction theory is addressed for typical Warburg elements and RC circuits based on the continued fraction expansion theory and the response error minimization technique,respectively;(ii)the order effect on the model reduction of typical Warburg elements is quantitatively evaluated by time–frequency analysis;(iii)the results of time–frequency analysis are confirmed to be useful to determine the reduction order in terms of the kinetic information needed to be captured;and(iv)the results of time–frequency analysis are validated for the model reduction of fractional impedance spectra for lithium-ion batteries,supercapacitors,and solid oxide fuel cells.In turn,the numerical validation has demonstrated the powerful function of the joint time–frequency analysis.The thorough model reduction of fractional impedance spectra addressed in the present work not only clarifies the relationship between time-domain transient analysis and frequency-domain stationary analysis but also enhances the reliability of the joint time–frequency analysis for electrochemical energy devices.

Boosting oxygen reduction activity and CO_(2) resistance on bismuth ferrite-based perovskite cathode for low-temperature solid oxide fuel cells below 600℃

Developing efficient and stable cathodes for low-temperature solid oxide fuel cells(LT-SOFCs) is of great importance for the practical commercialization.Herein,we propose a series of Sm-modified Bi_(0.7-x)Sm_xSr_(0.3)FeO_(3-δ) perovskites as highly-active catalysts for LT-SOFCs.Sm doping can significantly enhance the electrocata lytic activity and chemical stability of cathode.At 600℃,Bi_(0.675)Sm_(0.025)Sr_(0.3)FeO_(3-δ)(BSSF25) cathode has been found to be the optimum composition with a polarization resistance of 0.098 Ω cm^2,which is only around 22.8% of Bi_(0.7)Sr_(0.3)FeO_(3-δ)(BSF).A full cell utilizing BSSF25 displays an exceptional output density of 790 mW cm^(-2),which can operate continuously over100 h without obvious degradation.The remarkable electrochemical performance observed can be attributed to the improved O_(2) transport kinetics,superior surface oxygen adsorption capacity,as well as O_(2)p band centers in close proximity to the Fermi level.Moreover,larger average bonding energy(ABE) and the presence of highly acidic Bi,Sm,and Fe ions restrict the adsorption of CO_(2) on the cathode surface,resulting in excellent CO_(2) resistivity.This work provides valuable guidance for systematic design of efficient and durable catalysts for LT-SOFCs.

Study on concentration distribution and detonation characteristics for non-axisymmetric fuel dispersal

The study of non-axisymmetric fuel dispersal and detonation can provide reference for the prevention of industrial cloud explosion accidents and the design of fuel air explosive(FAE).The concentration and detonation fields of 85 kg cylindrical and fan-shaped fuel are investigated by experiments and numerical simulations.A dynamic model of the whole process for fuel dispersal and detonation is built.The concentration distribution of fuel is used as the initial condition to calculate the detonation stage,thus solving the initial value problem of detonation field.The phase and component changes of fuel cloud at different locations are compared.The fuel cloud is divided into directions of 0°,90°,135°and 180°.The results show that the maximum cloud radius is 20.94 m in 135°and the minimum is 12.04 m in 0°.The diameter of the detonation fireball is 53.6 m,and the peak temperature is 3455 K.The highest peak overpressure is 3.44 MPa in 0°and the lowest is 2.97 MPa in 135°.The proportion of liquid phase in 0°is22.90%,and the fuel loss is 11.8% and 9% higher than that in 135°and cylindrical charge,respectively.The stable propagation distance of blast wave in 135°is 42.50% longer than 0°and 28.37% longer than cylindrical charge.

Enhancing layered perovskite ferrites with ultra-high-density nanoparticles via cobalt doping for ceramic fuel cell anode

Nanoparticles anchored on the perovskite surface have gained considerable attention for their wide-ranging applications in heterogeneous catalysis and energy conversion due to their robust and integrated structural configuration.Herein,we employ controlled Co doping to effectively enhance the nanoparticle exsolution process in layered perovskite ferrites materials.CoFe alloy nanoparticles with ultra-high-density are exsolved on the(PrBa)_(0.95)(Fe_(0.8)Co_(0.1)Nb_(0.1))2O_(5+δ)(PBFCN_(0.1))surface under reducing atmosphere,providing significant amounts of reaction sites and good durability for hydrocarbon catalysis.Under a reducing atmosphere,cobalt facilitates the reduction of iron cations within PBFCN_(0.1),leading to the formation of CoFe alloy nanoparticles.This formation is accompanied by a cation exchange process,wherein,with the increase in temperature,partial cobalt ions are substituted by iron.Meanwhile,Co doping significantly enhance the electrical conductivity due to the stronger covalency of the Cosingle bondO bond compared with Fesingle bondO bond.A single cell with the configuration of PBFCN_(0.1)-Sm_(0.2)Ce_(0.8)O_(1.9)(SDC)|SDC|Ba_(0.5)Sr_(0.5)Co_(0.8)Fe_(0.2)O_(3−δ)(BSCF)-SDC achieves an extremely low polarization resistance of 0.0163Ωcm^(2)and a high peak power density of 740 mW cm^(−2)at 800℃.The cell also shows stable operation for 120 h in H_(2)with a constant current density of 285 mA cm^(−2).Furthermore,employing wet C_(2)H_(6)as fuel,the cell demonstrates remarkable performance,achieving peak power densities of 455 mW cm^(−2)at 800℃and 320 mW cm^(−2)at 750℃,marking improvements of 36%and 70%over the cell with(PrBa)_(0.95)(Fe_(0.9)Nb_(0.1))_(2)O_(5+δ)(PBFN)-SDC at these respective temperatures.This discovery emphasizes how temperature influences alloy nanoparticles exsolution within doped layered perovskite ferrites materials,paving the way for the development of high-performance ceramic fuel cell anodes.

Preparation and properties of high-energy-density aluminum/boroncontaining gelled fuels

Energetic nanofluid fuel has caught the attention of the field of aerospace liquid propellant for its high energy density(HED), but it suffers from the inevitable solid-liquid phase separation problem. To resolve this problem, herein we synthesized the high-Al-/B-containing(up to 30%(mass)) HED gelled fuels, with low-molecular-mass organic gellant Z, which show high net heat of combustion(NHOC), density, storage stability, and thixotropic properties. The characterizations indicate that the application of energetic particles to the gelled fuels obviously destroys their fibrous network structures but can provide the new particle-gellant gelation microstructures, resulting in the comparable stability between 1.0%(mass) Z/JP-10 + 30%(mass) Al or B and pure JP-10 gelled fuel. Moreover, the gelled fuels with high-content Al or B exhibit high shear-thinning property, recovery capability, and mechanical strength, which are favorable for their storage and utilization. Importantly, the prepared 1.0%(mass) Z/JP-10 + 30%(mass) B(or 1.0%(mass) Z/JP-10 + 30%(mass) Al) shows the density and NHOC 1.27 times(1.30) and 1.43 times(1.21)higher than pure JP-10, respectively. This work provides a facile and valid approach to the manufacturing of HED gelled fuels with high content of energetic particles for gel propellants.

Al^(3+) doped CeO_(2) for proton conducting fuel cells

Developing high ionic conducting electrolytes is crucial for applying proton-conducting fuel cell(PCFCs)practically.The cur-rent study investigates the effect of alumina on the structural,morphological,electrical,and electrochemical properties of CeO_(2).Lattice oxygen vacancies are induced in CeO_(2) by a general doping concept that enables fast ionic conduction at low-temperature ranges(300-500℃)for PCFCs.Rietveld refinement of the X-ray diffraction(XRD)patterns established the pure cubic fluorite structure of Al-doped CeO_(2)(ADC)samples and confirmed Al ions’fruitful integration in the CeO_(2) lattice.The electronic structure of the alumina-doped ceria of the materials(10ADC,20ADC,and 30ADC)has been investigated.As a result,it was found that the best composition of 30ADC-based electrolytes induced maximum lattice oxygen vacancies.The corresponding PCFC exhibited a maximum power output of 923 mW/cm^(2)at 500℃.Moreover,the investigation proves the proton-conducting ability of alumina-doped ceria-based fuel cells by using an oxide ion-blocking layer.

Correction to:Assembly-level analysis on temperature coefficient of reactivity in a graphite-moderated fuel salt reactor fueled with low-enriched uranium

Following publication of the original article,the authors observed that both Fig.5 and Fig.4 depict the same image.Figure 5 was inaccurately referenced and displayed.The correct Fig.5 is copied below:The original article has been updated.

A thermodynamic perspective on electrode poisoning in solid oxide fuel cells

A critical challenge to the commercialization of clean and high-efficiency solid oxide fuel cell(SOFC)technology is the insuf-ficient stack lifespan caused by a variety of degradation mechanisms,which are associated with cell components and chemical feedstocks.Cell components related degradation refers to thermal/chemical/electrochemical deterioration of cell materials under operating conditions,whereas the latter regards impurities in feedstocks of oxidant(air)and reductant(fuel).This article provides a thermodynamic perspective on the understanding of the impurities-induced degradation mechanisms in SOFCs.The discussion focuses on using thermodynamic ana-lysis to elucidate poisoning mechanisms in cathodes by impurity species such as Cr,CO_(2),H_(2)O,and SO_(2) and in the anode by species such as S(or H_(2)S),SiO_(2),and P_(2)(or PH_(3)).The author hopes the presented fundamental insights can provide a theoretical foundation for search-ing for better technical solutions to address the critical degradation challenges.

Catalyst design and structure control for photocatalytic refineries of cellulosic biomass to fuels and chemicals

Lignocellulosic biomass is the largest renewable hydrocarbon resource on earth.Converting cellulose,one of the major components of lignocellulose,powered by solar energy is a promising way of providing lowcarbon-footprint energy chemicals such as H_(2),HCOOH,CO,and transportation fuels.State-of-the-art biorefineries target the full use of biomass feedstocks as they have a maximum collection radius of 75-100 km,requesting efficient and selective photocatalysts that significantly influence the outcome of photocatalytic biorefineries.Well-performed photocatalysts can harvest a broad solar spectrum and are active in breaking the chemical bonds of cellulose,decreasing the capital investments of biorefineries.Besides,photocatalysts should control the selectivity of cellulose conversion,originating target products to level down separation costs.Charge separation in photocatalysts and interfacial charge transfer between photocatalysts and cellulose affect the activity and selectivity of cellulose refineries to H2 and carbonaceous chemicals.To account for the challenges above,this review summarizes photocatalysts for the refineries of cellulose and downstream platform molecules based on the types of products,with the structure features of different types of photocatalysts discussed in relation to the targets of either improving the activity or product selectivity.In addition,this review also sheds light on the methods for designing and regulating photocatalyst structures to facilitate photocatalytic refineries of cellulose and platform molecules,meanwhile summarizing proposed future research challenges and opportunities for designing efficient photocatalysts.

Relationship between hydrogenation degree and pyrolysis performance of jet fuel

Understanding the relationship between the chemical composition and pyrolysis performance of endothermic hydrocarbon fuel(EHF) is of great significance for the design and optimization of advanced EHFs. In this work, the effect of deep hydrogenation on the pyrolysis of commercial RP-3 is investigated.Fuels with different hydrogenation degrees were obtained by the partially and completely catalytic hydrogenation and their pyrolysis performances were investigated using an apparatus equipped with an electrically heated tubular reactor. The results show that with the increase of hydrogenation degree, fuel conversion almost remains constant during the pyrolysis process(500-650°C, 4 MPa);however, the heat sink increases slightly, and the anti-coking performance significantly improves, which are highly related to their H/C ratios. Detailed characterisations reveal that the difference of the pyrolysis performance can be ascribed to the content of aromatics and cycloalkanes: the former are prone to initiate secondary reactions to form coking precursors, while the latter could act as the hydrogen donor and release hydrogen, which will terminate the radical propagation reactions and suppress the coke deposition. This work should provide the guidance for upgrading EHFs by modulating the composition of EHFs.

Tandem hydroalkylation and deoxygenation of lignin-derived phenolics to synthesize high-density fuels

Lignin is the most abundant naturally phenolic biomass,and the synthesis of high-performance renewable fuel from lignin has attracted significant attention.We propose the efficient synthesis of high-density fuels using simulated lignin cracked oil in tandem with hydroalkylation and deoxygenation reactions.First,we investigated the reaction pathway for the hydroalkylation of phenol,which competes with the hydrodeoxygenation form cyclohexane.And then,we investigated the effects of metal catalyst types,the loading amount of metallic,acid dosage,and reactant ratio on the reaction results.The phenol hydroalkylation and hydrodeoxygenation were balanced when 180℃ and 5 MPa H_(2)with the alkanes yield of 95%.By extending the substrate to other lignin-derived phenolics and simulated lignin cracked oil,we obtained the polycyclic alkane fuel with high density of 0.918 g·ml^(-1)and calorific value of41.2 MJ·L^(-1).Besides,the fuel has good low-temperature properties(viscosity of 9.3 mm^(2)·s^(-1)at 20℃ and freezing point below-55℃),which is expected to be used as jet fuel.This work provides a promising way for the easy and green production of high-density fuel directly from real lignin oil.

Sustainable production of high-energy-density jet fuel via cycloaddition reactions

Developing an energy supply-chain based on renewable biomass holds great potential to build a low carbon society.High-energy-density(HED)jet fuel,featuring unique fused/strained cycloalkanes,is of great significance for volume-limited military aircrafts,as their high density and combustion heat can extend flight duration and increase the payload.Therefore,the exploration of biomass-based routes towards HED fuel has drawn much attention over the past decade.Cycloaddition reaction features rapid construction of various carbocycles in an atom-and step-economical fashion.This elegant strategy has been widely applied in the manufacture of sustainable HED fuel.Here we carefully summarize the progress achieved in this fascinating area and the review is categorized by the cycloaddition patterns including[4+2],[2+2],[4+4],and[2+1]cycloadditions.Besides,the energy densities of the as-prepared biofuels and petroleumbased fuels(conventional Jet-A and advanced JP-10)are also compared.This review will provide important insights into rational design of new HED fuel with different ring-types/sizes and inspire the chemists to turn those literature studies into practical applications in military field.

Probing the Efficiency of PPMG-Based Composite Electrolytes for Applications of Proton Exchange Membrane Fuel Cell

PPMG-based composite electrolytes were fabricated via the solution method using the polyvinyl alcohol and polyvinylpyrrolidone blend reinforced with various contents of sulfonated inorganic filler.Sulfuric acid was employed as the sulfonating agent to functionalize the external surface of the inorganic filler,i.e.,graphene oxide.The proton conductivities of the newly prepared proton exchange membranes(PEMs)were increased by increasing the temperature and content of sulfonated graphene oxide(SGO),i.e.,ranging from 0.025 S/cm to 0.060 S/cm.The induction of the optimum level of SGO is determined to be an excellent route to enhance ionic conductivity.The single-cell performance test was conducted by sandwiching the newly prepared PEMs between an anode(0.2 mg/cm^(2) Pt/Ru)and a cathode(0.2 mg/cm^(2) Pt)to prepare membrane electrode assemblies,followed by hot pressing under a pressure of approximately 100 kg/cm^(2) at 60℃for 5–10 min.The highest power densities achieved with PPMG PEMs were 14.9 and 35.60 mW/cm^(2) at 25℃and 70℃,respectively,at ambient pressure with 100%relative humidity.Results showed that the newly prepared PEMs exhibit good electrochemical performance.The results indicated that the prepared composite membrane with 6 wt%filler can be used as an alternative membrane for applications of high-performance proton exchange membrane fuel cell.

Recent progress on mechanisms,principles,and strategies for high-activity and high-stability non-PGM fuel cell catalyst design

The commercialization of a polymer membrane H2-O2 fuel cell and its widespread use call for the development of cost-effective oxygen reduction reaction(ORR)nonplatinum group metal(NPGM)catalysts.Nevertheless,to meet the requests for the real-world fuel cell application and replacing platinum catalysts,it still needs to address some challenges for NPGM catalysts regarding the sluggish ORR kinetics in the cathode and their poor durability in acidic environment.In response to these issues,numerous efforts have been made to study NPGM catalysts both theoretically and experimentally,developed these into the atomically dispersed coordinated metal-nitrogen-carbon(M-N-C)form over the past decades.In this review,we present a comprehensive summary of recent advancements on NPGM catalysts with high activity and durability.Catalyst design strategies in terms of optimizing active-site density and enhancing catalyst stability against demetalization and carbon corrosion are highlighted.It is also emphasized the importance of understanding the mechanisms and principles behind those strategies through a combination of theoretical modeling and experimental work.Especially,further understanding the mechanisms related to the active-site structure and the formation process of the single-atom active site under pyrolysis conditions is critical for active-site engineering.Optimizing the active-site distance is the basic principle for improving catalyst activity through increasing the catalyst active-site density.Theoretical studies for the catalyst deactivation mechanism and modeling stable active-site structures provide both mechanisms and principles to improve the NPGM catalyst durability.Finally,currently remained challenges and perspectives in the future on designing high-performance atomically dispersed NPGM catalysts toward fuel cell application are discussed.

Constructing the Al deficiency in Si-O(H)-Al units based on Pt/ZSM-5 for enhanced hydrocracking of polyethylene into high-quality liquid fuel

Hydrocracking catalysis is a controllable route to plastic waste upgrading. However, the mismatched acid site-driven C-C cleavage and C=C hydrogenation process on metal restrict the efficiency and selectivity in conventional metal/acid bi-functional catalyst. Herein, we introduce Al deficiency in Si-O(H)-Al structural units of Pt/zeolite socony mobil-5 (Pt/ZSM-5) through discharge driven reduction (DR) process to precisely control the ratio of metal to acid, achieving hydrocracking of low-density polyethylene (LDPE) waste at 270 °C with 87.7% conversion and liquid fuel (C5-C21) selectivity of 77.8%. Pair distribution function (PDF) and nuclear magnetic resonance (NMR) spectroscopy demonstrate the partial absent Al sites further resulting short-range local disorder Si-O(H)-Al. Upon pyridine infrared spectroscopy (Py-IR) and CO diffuse reflectance Fourier-transform infrared (CO DRIFT) analysis, the extraction of Al modulates Brønsted acid density of Pt/ZSM-5 with DR process (Pt/Z5DR), improves the interaction between Pt and ZSM-5 support, enhances the cationic of Pt. The metal-acid balance and electron-deficient Pt favor the matching speed of light olefins hydrogenation and the cracking of macromolecule intermediates. Moreover, density functional theory (DFT) calculations identify the thermodynamic stability of Pt/Z5DR and moderate adsorption capability towards light olefins. This work confirms the great potential of precisely controlled molar of metal to acid in metal/zeolite catalysts for LDPE upcycling, providing a viable path for dealing with PE plastic wastes.

Solar fuel production through concentrating light irradiation

The climate crisis necessitates the development of non-fossil energy sources.Harnessing solar energy for fuel production shows promise and offers the potential to utilize existing energy infrastructure.However,solar fuel production is in its early stages of development,constrained by low conversion efficiency and challenges in scaling up production.Concentrated solar energy(CSE)technology has matured alongside the rapid growth of solar thermal power plants.This review provides an overview of current CSE methods and solar fuel production,analyzes their integration compatibility,and delves into the theoretical mechanisms by which CSE impacts solar energy conversion efficiency and product selectivity in the context of photo-electrochemistry,thermochemistry,and photo-thermal co-catalysis for solar fuel production.The review also summarizes approaches to studying the photoelectric and photothermal effects of CSE.Lastly,it explores emerging novel CSE technology methods in the field of solar fuel production.