High-throughput microfluidic production of carbon capture microcapsules:fundamentals,applications,and perspectives

In the last three decades,carbon dioxide(CO_(2)) emissions have shown a significant increase from various sources.To address this pressing issue,the importance of reducing CO_(2) emissions has grown,leading to increased attention toward carbon capture,utilization,and storage strategies.Among these strategies,monodisperse microcapsules,produced by using droplet microfluidics,have emerged as promising tools for carbon capture,offering a potential solution to mitigate CO_(2) emissions.However,the limited yield of microcapsules due to the inherent low flow rate in droplet microfluidics remains a challenge.In this comprehensive review,the high-throughput production of carbon capture microcapsules using droplet microfluidics is focused on.Specifically,the detailed insights into microfluidic chip fabrication technologies,the microfluidic generation of emulsion droplets,along with the associated hydrodynamic considerations,and the generation of carbon capture microcapsules through droplet microfluidics are provided.This review highlights the substantial potential of droplet microfluidics as a promising technique for large-scale carbon capture microcapsule production,which could play a significant role in achieving carbon neutralization and emission reduction goals.

Performance and Application of Double-layered Microcapsule Corrosion Inhibitors

Double-layered microcapsule corrosion inhibitors were developed by sodium monofluorophosphate as the core material,polymethyl methacrylate as the inner wall material,and polyvinyl alcohol as the outer wall material combining the solvent evaporation method and spray drying method.The protection by the outer capsule wall was used to prolong the service life of the corrosion inhibitor.The dispersion,encapsulation,thermal stability of microcapsules,and the degradation rate of capsule wall in concrete pore solution were analyzed by ultra-deep field microscopy,scanning electron microscopy,thermal analyzer,and sodium ion release rate analysis.The microcapsules were incorporated into mortar samples containing steel reinforcement,and the effects of double-layered microcapsule corrosion inhibitors on the performance of the cement matrix and the actual corrosion-inhibiting effect were analyzed.The experimental results show that the double-layered microcapsules have a moderate particle size and uniform distribution,and the capsules were completely wrapped.The microcapsules as a whole have good thermal stability below 230 ℃.The monolayer membrane structure microcapsules completely broke within 1 day in the simulated concrete pore solution,and the double-layer membrane structure prolonged the service life of the microcapsules to 80 days in the simulated concrete pore solution before the core material was completely released.The mortar samples containing steel reinforcement incorporated with the double-layered microcapsule corrosion inhibitors still maintained a higher corrosion potential than the monolayer microcapsule corrosion inhibitors control group at 60 days.The incorporation of double-layered microcapsules into the cement matrix has no significant adverse effect on the setting time and early strength.

Research Progress of Aromatic Bed Curtains for Aiding Sleep Based on Lavender Microcapsule Technique

In this paper, the preparation technique of lavender essential oil microcapsules and the construction method of aromatic textiles were expounded, and the research status of bed curtains and lavender microcapsules at home and abroad was analyzed and studied from the perspective of application in textiles. The application of lavender essential oil to bed curtains through the microcapsule technique was put forward to allow lavender essential oil to play its role of helping sleep in bed curtains. This paper expounded the material selection and preparation technique of lavender microcapsule agents, and put forward the preparation method of microcapsules with mixed solutions of pure Chinese medicine extracts and natural essences as core material and high-viscosity epoxy resin as wall materials. The post-processing techniques and the spray ironing method for clothing were studied and developed, and these techniques and methods were applied to bed curtains, and good results were obtained.

Amphiphilicity-driven octaphenyl polyoxyethylenes regulate soft microcapsules flexibility for better foliar adhesion and pesticide utilization

Pesticide-loaded flexible carriers that allow for deformation and adhesion on crop leaves is an effective way to improve pesticide utilization.In interfacial polymerization,the addition of octaphenyl polyoxyethylene(OP)with different hydrophile lipophilic balances(HLBs)into the oil phase can regulate the flexibility of pyraclostrobinloaded microcapsules(MCs).Due to differences in amphiphilicity and molecular structure,OP redistributed on the oil-water two-phases and oil-water interface.With increasing HLB,the proportion of OP entering the aqueous phase increased.Furthermore,more OP with low HLB remained in the oil phase and occupied the oil-water interface,and these OPs participated in and regulated the interfacial polymerization to increase the thickness,reduce the compactness of the shell,and increase the hydroxyl and ether bond contents in the shell.Therefore,pyraclostrobin-loaded MCs with low HLB(11.5-12.5)OP-7 exhibited flexible deformation,strong foliar adhesion,good scouring resistance,and a high control effect on peanut leaf spot,which the disease severity was 3.67.For high HLB(16),OP-21-prepared MCs with compact shells were safer to zebrafish,which the safety index was 23.81.Using the amphiphilicity of OP molecules to drive their redistribution in an encapsulation system to regulate interfacial polymerization is an effective way to control the structure and performance of pesticideloaded MCs.

RP-HPLC determination of lycopene in microcapsules

Aim A RP- HPLC method for determination of lycopene in microcapsules was established. Methods The HPLC assay was performed on an Alltima Cls （4.6 mm × 250 mm, 5μm） column with a mixture of methanol-THF-water （66：30：4, V/V/V） as mobile phase at a flow rate of 1.5 mL·min^-1 and the UV detection wavelength was 472 nm. Results The linear range of lycopene was 3.6-18 μg·mL^-1, r = 0.999 8, the average recovery was from 99.81% to 101.06% with RSD less than 1.83%. The RSD of intra-day and interday precision were less than 3.34%. Conclusion The method is simple, accurate and suitable for the determination of lycopene in microcapsules.

Preparation and in Vitro Evaluation of Polylactic Acid (PLA) or Polylactic-co-Glycolic Acid (PLGA) Microcapsules Loaded with Estradiol

Aim PLA/PLGA was used as biodegradable and biocompatible carriers to achieve sustained release of estradiol (E 2). Methods Microcapsules (MC) were prepared by an emulsification solvent extraction method, and then the properties and in vitro drug release behavior of MC were examined. An analysis of variance (ANOVA) was used to test the statistical significance. Then, multiple comparisons were made with a T method between levels to examine the significance of difference further. For all the results a P value 】0 05 was considered statistically insignificant . Results Under the same conditions, the water adding speed and the particle size had significant effects ( P 【0 01) on the entrapment efficiency of MC; the water adding speed and the concentration of PLA in the oil phase had significant effects ( P 【0 01) on the diameter MC in medium. Release of E 2 from MC was influenced significantly ( P 【0 01) by the water adding speed and the type and molecule weight of the polymers. But the differences between levels of the variates were not all significant. Conclusion E 2 PLA/PLGA MC with various properties can be formed when the formulation and the technology were changed accordingly.

Microstructure and deposition mechanism of electrodeposited Cu/liquid microcapsule composite

The nanostructured copper/microcapsule containing liquid core materials composite（copper/liquid microcapsules composite） was prepared using direct current（DC） electrodeposition method.The surface morphology and microstructure of composite were investigated by means of scanning electron microscopy（SEM）,transmission electron microscopy（TEM） and X-ray diffraction（XRD）.The results show that the microstructure of electrodeposited layer transformed from bulk crystal to nano structure because of the participation of microcapsules.The diameters of microcapsules and the copper grain sizes in the composite were 2？20 μm and 10？20 nm,respectively.In addition,the electrodeposition mechanism of composite in the deposition process followed electrochemistry theory,which was proved by the theoretical analysis result and the experiment results.Meanwhile,the co-deposition process model was presented.

Synthesis and Characterization of Microcapsules with Chlorpyrifos Cores and Polyurea Walls

Microcapsules with chlorpyrifos cores and polyurea walls were synthesized with 2,4-tolylene diisocyanate as an oil-soluble monomer and ethylenediamine as a water-soluble monomer via an interracial polycondensation reaction. The products were characterized by means of Fourier transform infrared spectrometry, ^13C NMR spectrometry and ^31p NMR spectrometry. The morphology, the particle size and the particle size distribution, and the thermal properties were also evaluated. The prepared microcapsules exhibit clear and smooth surfaces and have a mean diameter of 28. 13 μm. These microcapsules also have a good thermal stability for long-term use, and have potential applications in minimizing the toxicity of chlorpyrifos through controlled release.

Research on microcapsules of phase change materials

Microcapsule technology is a kind of technology wrapping the solid or liquid into minute-sized particles within the field of micrometer or millimeter with film forming materials. This thesis introduces microcapsule technology of phase change materials and its main functions and the structural composition, preparation methods and characterization technology of microcapsule of phase change materials. The microcapsule of phase change materials is small in size and its temperature remains unchanged during the process of heat absorption and heat release. It is of great value in research and application prospect due to these characteristics.

Numerical Analysis on Thermal Function of Clothing with PCM Microcapsules

To study the influences of phase change material(PCM)microcapsules in clothing on human thermal responses,a mathematical model is developed.The improved Stolwijk’s model is used to simulate human thermo-regulatory process,and the coupled heat and moisture transfer including the moisture sorption/desorption of fibers and effects of phase transition temperature range on the phase change processes of the PCM is considered in clothing model.Meanwhile,the theoretical predictions are validated by experimental data.Then,the interactions between human body thermal responses and the heat and moisture transfer in clothing are discussed by comparing the prediction results with PCMs and without PCMs.Also the effects of fiber hygroscopicity on clothing and human thermal responses are compared.The conclusion shows that the clothing with PCMs microcapsules can delay the human temperature variations and decrease the sweat accumulation rate on the skin surface and heat loss during changing of ambient conditions,and fiber hygroscopicity reduces the effect of PCM microcapsules on delaying garment temperature variations very significantly.

Preparation and characterization of hexadecane microcapsule with polyurea-melamine formaldehyde resin shell materials

This paper gives a brief report of the preparation of hexadecane microcapsule with polyurea-melamine formaldehyde resin shell materials(HMPM).The sealing performance and thermal stability of HMPM was enhanced much more effectively than that of microcapsule with polyurea shell material(HPM).The results of microscopical imaging analysis system,DSC,TG,and laser particle analyzer were briefly introduced.

Culture of yeast cells immobilized by alginate-chitosan microcapsules in aqueous-organic solvent biphasic system

Immobilization biocatalysis is a potential technology to improve the activity and stability of biocatalysts in nonaqueous systems for efficient industrial production.Alginate-chitosan(AC)microcapsules were prepared as immobilization carriers by emulsifi cation-internal gelation and complexation reaction,and their contribution on facilitating the growth and metabolism of yeast cells were testifi ed successfully in culture medium-solvent biphasic systems.The cell growth in AC microcapsules is superior to that in alginate beads,and the cells in both immobilization carriers maintain much higher activity than free cells,which demonstrates AC microcapsules can confer yeast cells the ability to resist the adverse effect of solvent.Moreover,the performance of AC microcapsules in biphasic systems could be improved by adjusting the formation of outer polyelectrolyte complex(PEC)membrane to promote the cell growth and metabolic ability under the balance of resisting solvent toxicity and permitting substrate diffusion.Therefore,these findings are quite valuable for applying AC microcapsules as novel immobilization carriers to realize the biotransformation of value-added products in aqueous-solvent biphasic systems.

Synthesis of melamine-formaldehyde microcapsules containing oil-based fragrances via intermediate polyacrylate bridging layers

A general and versatile strategy to prepare melamine-formaldehyde(MF)microcapsules encapsulating oil-based fragrances by combining solvent evaporation and in situ polymerization was proposed in this work.The oil-based fragrance was pre-encapsulated by an inner polyacrylate membrane via solvent evaporation,followed by in situ polymerization of MF precondensates as an outer shell.The polyacrylate membrane is used as an intermediate bridging layer to stabilize the oil-based fragrance,and to provide driving forces for in situ polymerization of MF precondensates through electrostatic attractions between carboxyl groups and ammonium ions.It was demonstrated that MF microcapsules containing clove oil were prepared successfully.The amount and the composition of the intermediate polyacrylate bridging layer were critical.Smooth and sphere-shaped MF-clove oil microcapsules were prepared when the weight ratio of polyacrylate to clove oil was over 60 wt%and the concentration of acrylic acid(AA)increased to 10 wt%in polyacrylate.In addition,MF microcapsules containing sunflower oil and hexyl salicylate were prepared by using this method.The work suggests that this new approach can be potentially used to encapsulate various core materials,tuning the shell properties of microcapsules such as thickness,mechanical strength and release properties.

Preparation and Characterization of Microcapsules for Self-healing Materials

The urea-formaldehyde（UF） capsules filled with a healing agent, a mixture of epoxy resins（epoxy 711 and E-51） as core material, were produced by means of one step in-situ polymerization. The characteristics of these microcapsules were studied via scanning electron microscopy（SEM）, particle size analysis, FTIR and DSC/TGA. The results show that the dispersed and integrated microcapsules of 5 μm in shell thickness were synthesized successfully. The capsules were produced with diameters ranging from 10 to 250 μm via controlling agitation rate. Young＇s modulus of the capsule was a little lower than those of the epoxy resins, but the microcapsules having such a shell thickness were robust enough to survive handling during manufacturing self-healing composites. When damage occurred in the epoxy matrix, the crack could rupture the microcapsule to make the repairing agent release.

Effect of Sodium Alginate Concentration on Membrane Strength and Permeating Property of Poly-l-arginine Group Microcapsule

A novel poly-/-arginine microcapsule was prepared due to its nutritional function and pharmacological efficacy. A high-voltage electrostatic droplet generator was used to make uniform microcapsules. The results show that the membrane strength and permeating property are both remarkably affected with the changes of sodium alginate concentration. With the sodium alginate concentration increasing, gel beads sizes increase from 233μm to 350μm, release ratio is also higher at the same time, but the membrane strength decreases.

Diffusion Characteristics in Microcapsules

An equation of diffusion for microcapsules（hollow sphere）was developed,employing the mathematicalmodel for the diffusion characteristics of solid sphere.In the proposed equation,a combination diffusion coeffi-cient was introduced as a substitute for the diffusion coefficient in the solid sphere mathematical model and ex-pressed as a function of the diffusion coefficient inside solution of hollow sphere,as well as in the polymer mem-brane.With this modified model,the diffusion coefficients of glucose in NaCS（sodium cellulose sulfate）-PDADMAC（Poly-diallyl-dimethyl-ammonium chloride）membrane and in Ca-alginate gel membrane were deter-mined.The diffusion coefficient in NaCS-PDADMAC membrane was found to be 2.12×10-11m2·s-1and thatin Ca-alginate membrane 2.62×10-10m2·s-1.

Biomass Microcapsules with Stem Cell Encapsulation for Bone Repair

Bone defects caused by trauma,tumor,or osteoarthritis remain challenging due to the lack of effective treatments in clinic.Stem cell transplantation has emerged as an alternative approach for bone repair and attracted widespread attention owing to its excellent biological activities and therapy effect.The attempts to develop this therapeutic approach focus on the generation of effective cell delivery vehicles,since the shortcomings of direct injection of stem cells into target tissues.Here,we developed a novel core-shell microcapsule with a stem cell-laden core and a biomass shell by using all-aqueous phase microfluidic electrospray technology.The designed core-shell microcapsules showed a high cell viability during the culture procedure.In addition,the animal experiments exhibited that stem cell-laden core-shell microcapsules have good biocompatibility and therapeutic effect for bone defects.This study indicated that the core-shell biomass microcapsules generated by microfluidic electrospray have promising potential in tissue engineering and regenerative medicine.

Measurement and Influence Factors of the Flowability of Microcapsules with High-content β-Carotene

The flowability of five kinds of microencapsulation powders,with differentβ-carotene contents and by two alternative particle-forming technologies i.e.spray-drying and starch-catching beadlet technology,was meas- ured.The actual flow properties of the five powders were compared based on bin-flow test,and three flow indexes (Hausner ratio,repose angle and flow index)were measured.It was found that the repose angle is the most suitable index to reflect the flowability of these powders for the particle properties would not be altered due to compaction or tapping during the measuring process.Particle size and particle size distribution play most important roles in the flowability of these granular materials,which was also influenced by other factors like shape,surface texture,sur- face roughness,etc.Microcapsules with wall material of gelatin and a layer of modified starch absorbed on the sur- face showed excellent flowabilities and good mechanical properties,and they are favorable for tabletting to supply β-carotene.

Facile and High Efficient Fabrication of Hybrid Microcapsules for Urease Encapsulation and Their Use as Biomimetic Reactors

Urease-loaded colloidosome microcapsules with SiO2 nanoparticle shells and gellan gel cores were prepared facilely and highly efficiently by self-assembly of colloidal particles at the liquid-liquid interfaces and subsequently in-situ gelation of gellan gum. The urease-loaded colloidosome microcapsules were used as an enzymatic reactor to produce calcium carbonate precipitates by urease-catalyzed urea hydrolysis in the presence of calcium cations. The CaCO3/SiO2 shells were formed finally around the gellan gel cores. The colloidosome microcapsules used as a biomimetic reactor has been demonstrated for the first time.

An enzyme-loaded reactor using metal-organic framework-templated polydopamine microcapsule

Ultrathin polydopamine microcapsules with hierarchical structure and porosity were prepared for the immobilization of multienzymes using metal-organic framework(MOF) as the template.The multienzyme/MOF composite was first prepared using a "one-pot" co-precipitation approach via the coordination and self-assembly of zinc ions and 2-methylimidazole in the presence of enzymes.The obtained nanoparticles were then coated with polydopamine thin layer through the self-polymerization of dopamine under alkaline condition.The polydopamine microcapsules with an ultrathin shell thickness of ~48 nm were finally generated by removing the MOF template at acidic condition.Three enzymes were encapsulated in PDA microcapsules including carbonic anhydrase(CA),formate dehydrogenase(FateDH),and glutamate dehydrogenase(GDH).FateDH that catalyzed the main reaction of CO_(2) reduction to formic acid retained 94.7% activity of equivalent free FateDH.Compared with free multienzymes,the immobilized ones embedded in PDA microcapsules exhibited 4.5-times higher of formate production and high catalytic efficiency with a co-factor-based formate yield of 342%.