Cost-Effective Monitoring of the Fuel Air Equivalence-Ratio with a Lambda Sensor and a Microcontroller in a Downdraft Biomass Gasifier

The operation of biomass treatment devices such as gasifiers is based on the control of key parameters that play an important role in product formation. These include: temperature, excess oxygen, relative humidity and biomass composition. This work focuses on excess oxygen and temperature. Unfortunately, flue gas oxygen analyzers are expensive and not accessible to small industries. However, the equivalence ratio is linked to excess oxygen and has the advantage of not depending on biomass composition. This study therefore focuses on the design and development of a device for controlling this equivalence ratio by measuring oxygen concentration using a self-propelled Lambda probe, and a system for monitoring this equivalence ratio using an Arduino Uno 3 microcontroller. The temperature is recorded with an accuracy of ±1.5°C. For a heating time of 10 minutes, the response time to temperature change is around 3 seconds, which is sufficient for the device to function properly. This simple device is an efficient and cost-effective means of checking the equivalence ratio.

Design of Intelligent Window Automatic Monitoring System Based on Microcontroller Control

To ensure the safety of residents’lives and property by using automatic opening and closing of ordinary windows,this article designs an intelligent window automatic monitoring system.The article proposes a software and hardware design scheme for the system,which comprises a microcontroller control module,temperature and humidity detection module,harmful gas detection module,rainfall detection module,human thermal radiation induction module,Organic Light-Emitting Diode(OLED)display module,stepper motor drive module,Wi-Fi communication module,etc.Users use this system to monitor environmental data such as temperature,humidity,rainfall,harmful gas concentrations,and human health.Users can control the opening and closing of windows through manual,microcontroller,and mobile application(app)remote methods,providing users with a more convenient,comfortable,and safe living environment.

Microcontroller Design Based on Dynamic Heterogeneous Redundancy Architecture

Redundancy control can effectively enhance the stability and robustness of a system.Based on the conventional redundancy control switchover and majority arbitration strategy,this paper introduces the concept of heterogeneity and dynamics,constructs a dynamic heterogeneous redundancy-based microcontroller architecture DHR-MCU,and designs a fixed-leader distributed consensus algorithm that satisfies the program running state control of this architecture.The theoretical analysis and actual measurement of the prototype system prove that this architecture has good anti-attack and self-recovery capabilities under normal functions and performances and meets the general robust features in terms of safety and security.

基于ArchC进行嵌入式Microcontroller设计研究

介绍了一种实用的以SystemC为基础的体系结构描述语言(ADL)—ArchC,首先简单对ArchC软件工具包进行了说明,接着重点介绍了以ArchC为工具进行Microcontroller设计的原理和简单流程,并说明了其关键技术,最后作了一个简单的总结.

Improved direct power injection model of 16-bit microcontroller for electromagnetic immunity prediction

To promote the modeling standardization process of the integrated circuits, an improved electrical simulation model for a direct power injection （DPI） setup which was used to measure the conducted immunity of a 16-bit microcontroller to radio frequency aggression was investigated. Based on the existing model of the same microcontroller, the PDN module was modified by adding the core, PLL and MD network models, which could reflect the actual electric distribution situation within the microcontroller more accurately. By comparing the simulation results with the measurement results, the effectiveness of the modified model can be improved to 500 MHz, and its uncertainty is within ＋1.8 dB （＋2 dB is acceptable）. Then, to improve the simulation accuracy of the complete model in the high frequency range, the I/O model which contained the dynamic and nonlinear characteristics reflecting the variation of the internal impedance of the microcontroller with increasing the frequency of the external noise was introduced. By comparing the simulation results with the measurement results, the effectiveness of the second modified model can be improved up to 1.4 GHz with the uncertainty of ~1.8 dB. Thus, a conclusion can be reached that the proposed model can be applied to a much wider frequency range with a smaller uncertainty than the latest model of the similar type. Furthermore, associated with the electromagnetic emission testing platform model, the PDN module can also be used to predict the electromagnetic conducted and radiated emission characteristics. This modeling method can also be applied to other integrated circuits, which is very helpful to the standardization of the IC electromagnetic compatibility （EMC） modeling process.

The Features of Microcontroller EM78P447 and Technique of Port Connection with I^2C Series Bus

By describing the technique of port connection and flow chart ofR/W operation between 24LC01, serial E2PROM, and EM78P447A, features of EM78P447 and its connection with I2C serial bus are introduced. In the end, the programe of writing operation is given.

Reducing Power and Energy Consumption of Nonvolatile Microcontrollers with Transparent On-Chip Instruction Cache

Demands for low-energy microcontrollers have been increasing in recent years. Since most microcontrollers achieve user programmability by integrating nonvolatile (NV) memories such as flash memories for storing their programs, the large power consumption required in accessing an NV memory has become a major problem. This problem becomes critical when the power supply voltage of NV microcontrollers is decreased. We can solve this problem by introducing an instruction cache, thus reducing the access frequency of the NV memory. Unlike general-purpose microprocessors, microcontrollers used for real-time applications in embedded systems must accurately calculate program execution time prior to its execution. Therefore, we introduce a “transparent” instruction cache, which does not change the existing NV microcontroller’s cycle-level execution time, for reducing power and energy consumption, but not for improving the processing speed. We have conducted detailed microar chitecture design based on the architecture of a major industrial microcontroller, and we evaluated power and energy consumption for several benchmark programs. Our evaluation shows that the proposed instruction cache can successfully reduce energy consumption in a fairly wide range of practical NV microcontroller configurations.

Design and Implementation of Electronic Control Trainer with PIC Microcontroller

This paper describes the implementation of a PIC microcontroller in a conventional laboratory-type electronic trainer. The work comprises software for the PIC and hardware for the software. The PIC controller uses an EasyPIC6 board and includes a PC-interfaced programmer for the PIC chip. It has many external modules: 128 × 64 graphic LCD display, 2 × 16 LCD display, 4 × 4 keypad, and port expander, all in the same bench. The trainer is capable of 36 experiments in logic/analogue electronic and control systems. A 5-sided approximate sensor, two photoelectric sensors (BR56-DDT-P and BEN9M-TFR), four CMOS, four BCD-7-segment driven by CD4511B, two relays (2-pole and 3-pole), six voltages, ammeter measurement, DC motor, and 24VDC power supply, connect through connectors and pinions. Results of all the experiments show the trainer satisfying requirements of undergraduate and postgraduate projects involving conventional electronic and classical control systems.

Microcontroller-Based Sinusoidal Voltage Generation for Electrical Bio-Impedance Spectroscopy Applications

A sinusoidal voltage wave generator is proposed based on the use of micro-processor digital signals with programmable duty-cycles, with application to real-time Electrical Cell-substrate Impedance Spectroscopy (ECIS) assays in cell cultures. The working principle relies on the time convolution of the programmed microcontroller (μC) digital signals. The expected frequency is easily tuned on the bio-impedance spectroscopy range [100 Hz, 1 MHz] thanks to the μC clock frequency selection. This system has been simulated and tested on the 8 bits μC ArduinoTM Uno with ATmega328 version. Results obtained prove that only three digital signals are required to fit the general specification in ECIS experiments, below 1% THD accuracy, and show the appropriateness of the system for the real-time monitoring of this type of biological experiments.

Two Axes Solar Tracker Based on Solar Maps, Controlled by a Low-Power Microcontroller

There are actually several solutions for two axis solar tracking systems using electromechanical devices, in which a controller detects the Sun apparent position, and controls the position of the structure supporting the panels toward the sun by enabling the engines movement. This work studies the solution of two axis solar tracking system based on solar maps, which can predict the exact apparent position of the Sun, by the latitude＇s location, thereby avoiding the need to use sensors or guidance systems. To accomplish this, it is used a low-power microcontroller, suitably programmed, to control two electric motors to ensure that the panels supporting structure is always oriented towards the sun.

Synergistic effects of neutron and gamma ray irradiation of a commercial CHMOS microcontroller

This paper presents the experimental results of a combined irradiation environment of neutron and gamma rays on 80C196KC20, which is a 16-bit high performance member of the MCS96 microcontroller family. The electrical and functional tests were made in three irradiation environments： neutron, gamma rays, combined irradiation of neutron and gamma rays. The experimental results show that the neutron irradiation can affect the total ionizing dose behaviour. Compared with the single radiation environment, the microcontroller exhibits considerably more severe degradation in neutron and gamma ray synergistic irradiation. This phenomenon may cause a significant hardness assurance problem.

Primary Function of Microcontroller EM78P458 and Research on Applications of Its ADC on Chip

The build-in structure of microcontroller EM78P458 and its application in supervising the water level of solar water heater are introduced. The circuit and the flow chart of AD conversion program are depicted. In the end, the design of assembly language program about the AD conversion is introduced.

Intravenous-Accelerated Saline Particles to Unblock Partially Clogged Blood Vessels Using a Microcontroller

This research assesses the speed of saline fluid in vein vessels using venipuncture medical kit as well as DC submersive pumps that are being controlled by a microcontroller. The microcontroller is monitored and governed using a software IDE interface installed on a powerful laptop. Saline solution is being pumped through a medical syringe at variable speeds up to a maximum of 18.39 cm/second to the vein. The novel technique in this research is the usage of two pumps called Pump 1 and Pump 2. Pump 1 is used to physically model the flow of “blood” in human vein and the second pump (Pump 2) is used to generate the accelerated saline particles that are used to break the yellow grease that is placed on the inside of the vein’s wall. A tiny brush is briefly dipped into yellow grease, and then it is used to place one layer (one turn) of yellow grease on the inside of the vein’s wall, and then this procedure is repeated to place consecutive layers of yellow grease onto the inside of the wall of the vein vessel using a tiny brush. It was found that accelerated saline particles can in fact destroy fats that are built up inside the veins’ walls.

Design of digital pressure gauge based on ATmega16 microcontroller

The combination of sensor and computer technology makes the measurement of various physical quantities easy, convenient and smart. In this article, a digital pressure gauge that is suitable for measuring liquid pressure is designed. The design of high precision digital pressure gauge uses pressure sensor as its foundation and uses ATmegal6 as its controller.

Design of a Microcontroller-Based Data Acquisition System for Ground Weather Observations: Evaluation of Radio Refractivity of Air

A meteorological data acquisition system is built using a PIC16F877A microcontroller and electric output-based sensors. This system is programmed in C language using the PCWH compiler. It is smart, accurate, cheap, small, light and easily movable. It is designed to automatically get instantaneous measurements of air temperature, atmospheric pressure, and relative humidity. Depending on their utilisation, these measurements are collected with repetition rate tuneable from one minute to one hour. They are displayed on LCD screen and transferred to a personal computer where they are stored and processed. As an application, such data are recorded in situ and used to estimate the radio refractivity of air near the ground in real time. This parameter is necessary to account for the propagation of radiofrequency waves through the lower atmosphere, during wireless transmissions.

Development of a Microcontroller Based DC Motor Speed Control System

This work reports the development of a microcontroller based control system to change the speed?of?a DC motor. Pulse Width Modulation?(PWM)?technique was used to control the amount of power delivered to the load (the DC motor) without dissipating any wasted power. The components and assembly of this microcontroller circuit are highlighted in this paper, and the constructed circuit tested. This device was used to control the speed of a rotating fan attached to a DC motor. The DC motor speed variations were read from a Tachometer connected to this motor and the results obtained show good agreement with our expectations. DC Motor speed microcontroller devices find applications in many areas of life, and its applications in small scale industrial settings will no doubt enhance the quest for development in a developing nation like ours.

Microcontroller Control of Reactive Power Compensation for Growing Industrial Loads

Many industrial installations in developing countries start-up as small factories, without regard for the need of compensation of reactive power, leading to significant financial losses in the long term. By improving the power factor, the customer can reduce its power demand and potentially increase efficiency of their equipment. A PIC microcontroller is used to switch capacitor banks to compensate for the reactive power. In order to determine the size of the capacitor bank needed, the microcontroller calculates the phase difference between the voltage and the current. The results obtained based on the lagging power factor for three test loads show an improvement in the power factor from 0.52 to 0.96 under different test load conditions.

Digital Lock-in Amplifier Based on Microcontroller

A method of implementing high cost-effective and highly integrated digital lock-in amplifier with microcontroller is discussed. And the digital lock-in amplifier is more suitable for meastwing lowfrequency weak signal. Digital signal sequence is obtained through sampling signal measured over an integer number of signal periods, but digital reference sequence is acquired through mathematical operation, then digital phase sensitive detection can be implemented by calculating the cross-correlation function of digital signal sequence and digital reference sequence. In addition, the frequency response and phase character of the digital lock-in amplifier is analyzed. Finally, the designed digital lock-in amplifier is achieved. Expermental results show that the digital lock-in amplifier can be used for measuring weak signal with low ignal-to-noise ratio.

A Simplified Microcontroller Based Potentiostat for Low-Resource Applications

A low component count, microcontroller-based potentiostat circuit was developed through the use of operational amplifiers arranged in different feedback configurations. This was developed to alleviate the cost burden of equipment procurement in low-cost and budget applications. Simplicity was achieved in the design by the use of the microcontroller’s native functionalities and a low-cost R/2R resistor ladder digital-to-analogue converter. The potentiostat was used to investigate the Ni2+/Ni(s) redox couple in a 3-electrode cell with a silver/silver chloride reference electrode and graphite counter and working electrodes. Linear sweep voltammograms were ob-tained at scan rates of 10, 20, 30 and 40 mV/s. The analysis of the peak current versus (scan rate)1/2 plot indicated that the Ni2+/Ni(s) reduction, though conforming to the Randles-Sevcik equation, was a non-reversible redox reaction.

Design and Construction of a Microcontroller Based Electronic Moving Message Display

LED-based moving-message displays are becoming appreciated among the general public for transmitting information to groups of people quickly. This work presents a simple design and implementation of a microcontroller-based electronic moving message display system. The design involves the arrangement of Light Emitting Diodes (LEDs) and the programming of a microcontroller that controls and determines the pattern and session of the display. The implementation of a moving message displays a text containing 22 characters (i.e. WELCOME TO DEPT. OF PHYSICS). The electronic message display helps to pass information, educates, enlightens, facilitates commercial activities through the advertisement and marketing of goods and services, description of places, etc. The ease in which it displays information makes it a veritable, suitable, and excellent tool for passing information fast and pleasurable to the public. Furthermore, it enhances the response to information in an attractive way and manner in which it displays messages. The microcontroller used in this work is the PIC16F84A. It belongs to a class of 8-bit microcontrollers of RISC (reduced instructions set) architecture. Its output controls the switching of the relays through a transistor switching stage that switches its socket. The LED matrix (array) is arranged in parallel and soldered to a Vero board with the microcontroller and other electronic components, such as resistors, capacitors, transistors, relays, LEDs, diodes, and transformers. In view, this work served as a means of digging into the technology involved in the use of a microcontroller and some other basic electronic components and enhanced visualization of message display.