In this study,the machined surface quality of powder metallurgy nickel-based superalloy FGH96(similar to Rene88DT)and the grinding characteristics of brown alumina(BA)and microcrystalline alumina(MA)abrasive wheels we...In this study,the machined surface quality of powder metallurgy nickel-based superalloy FGH96(similar to Rene88DT)and the grinding characteristics of brown alumina(BA)and microcrystalline alumina(MA)abrasive wheels were comparatively analyzed during creep feed grinding.The infuences of the grinding parameters(abrasive wheel speed,workpiece infeed speed,and depth of cut)on the grinding force,grinding temperature,surface roughness,surface morphology,tool wear,and grinding ratio were analyzed comprehensively.The experimental results showed that there was no significant difference in terms of the machined surface quality and grinding characteristics of FGH96 during grinding with the two types of abrasive wheels.This was mainly because the grinding advantages of the MA wheel were weakened for the difficult-to-cut FGH96 material.Moreover,both the BA and MA abrasive wheeIs exhibited severe tool wear in the form of wheel clogging and workpiece material adhesion.Finally,an analytical model for prediction of the grinding ratio was established by combining the tool wear volume,grinding force,and grinding length.The acceptable errors between the predicted and experimental grinding ratios(ranging from 0.6 to 1.8)were 7.56%and 6.31%for the BA and MA abrasive wheels,respectively.This model can be used to evaluate quantitatively the grinding performance of an alumina abrasive wheel,and is therefore helpful for optimizing the grinding parameters in the creep feed grinding process.展开更多
As is known to all, grinding force is one of the most important parameters to evaluate the whole process of grinding. Generally, the grinding force is resolved to three component forces, namely, normal grinding force ...As is known to all, grinding force is one of the most important parameters to evaluate the whole process of grinding. Generally, the grinding force is resolved to three component forces, namely, normal grinding force F n, tangential grinding force F t and a component force acting along the direction of longitudinal feed which is usually neglected because of insignificance. The normal grinding force F n has influence upon surface deformation and roughness of workpiece, while the tangential grinding force F t mainly affect power consumption and service life of grinding wheel. In order to study deep into the process of the unsteady state grinding, we set up a measurement system to monitor the change of grinding force during the course of grinding and try to find some difference in the change of grinding force between the steady state grinding and unsteady state grinding. In the test, the normal and tangential grinding forces, F n and F t were measured by using a set of equipments including sensor, amplifier, oscilloscope and computer monitor. From the results, we can conclude that: 1) In the unsteady state grinding process, the values of the grinding forces are much lower than those of the steady state grinding process and the grinding force ratio showed a nonlinear fluctuation. 2) The tendency of the grinding forces in the process of the unsteady state grinding proved the existence of the cutting and micro-cutting actions. 3) Because the grinding force signals of the unsteady state grinding are much weaker than those of the steady state grinding, to obtain accurate value of the grinding forces, wave filtering is needed to be done. The whole process to filter the perturbation wave can be separated into three steps in order, changing the grinding force signals from analog signals into digital signals, FFT (fast Fourier transform) treatment to the digital signals, and IFFT(inversion fast Fourier transform) treatment to the digital signals after spectrum limitation.展开更多
In conventional grinding theory, it is obvious that there must be a very high hardness difference between grains of the grinding wheel and workpieces. The best grinding wheels are those giving the lowest "natural...In conventional grinding theory, it is obvious that there must be a very high hardness difference between grains of the grinding wheel and workpieces. The best grinding wheels are those giving the lowest "natural limiting surface roughness" while cutting at appreciable plunge velocities. With the development of new materials and new machining processes, conventional theories of grinding techniques are no longer suitable to explain many phenomena in the course of grinding procedures. In dealing with precision or ultra-precision grinding processes of advanced ceramics, many results of experiments and practical production have shown that grinding with super hard materials wheels is not the only method to machine advanced ceramics. This paper is intended to propose a new grinding theory named as unsteady-state grinding technique evolved from some phenomena that can not be explained by conventional grinding theory. Unsteady-state grinding technique means the technique which can make the surface roughness of the materials, especially hard and brittle, be up to the standard of ultra-precision machining by utilizing common wheels characteristic of inferior self-sharpening and wear-resistance. In the process of machining, the common wheel need to be redressed about 3～5 times and the time between two redressings is about 3～5 minutes. As a validation of the new grinding technology, experimental work was performed to prove the existence of the unsteady state in the process of ultra-precision grinding with common abrasive wheel-pink fused alumina wheel. From the results of the observation of the wheel topography, the whole grinding process in unsteady state was separated into three stages namely cutting by grains peaks, micro-cutting by micro edges of the broken grains and rubbing without material removal, which is different from conventional grinding theory. For the difference of hardness between grinding wheel and workpiece material is not so apparent, some people have doubts about whether the cutting especially micro-cutting actions exist in the process of unsteady state grinding. By utilizing the common abrasive wheel newly redressed to grind the finished surface of silicon nitride glut and comparing the finished surface with the damaged surface in SEM pattern and surface roughness, the existence of cutting and micro- cutting actions in the unsteady state grinding process was confirmed.展开更多
基金supported by the National Natural Science Foundation of China(Grant Nos.51775275 and 51921003)National Major Science and Technology Project(Grant No.2017-Ⅶ-0002-0095)+2 种基金Funding for Outstanding Doctoral Dissertation in NUAA(Grant No.BCXJ19-06)the Six Talents Summit Project in Jiangsu Province(Grant No.JXQC-002)Fundamental Research Funds for the Central Universities(Grant No.NP2018110).
文摘In this study,the machined surface quality of powder metallurgy nickel-based superalloy FGH96(similar to Rene88DT)and the grinding characteristics of brown alumina(BA)and microcrystalline alumina(MA)abrasive wheels were comparatively analyzed during creep feed grinding.The infuences of the grinding parameters(abrasive wheel speed,workpiece infeed speed,and depth of cut)on the grinding force,grinding temperature,surface roughness,surface morphology,tool wear,and grinding ratio were analyzed comprehensively.The experimental results showed that there was no significant difference in terms of the machined surface quality and grinding characteristics of FGH96 during grinding with the two types of abrasive wheels.This was mainly because the grinding advantages of the MA wheel were weakened for the difficult-to-cut FGH96 material.Moreover,both the BA and MA abrasive wheeIs exhibited severe tool wear in the form of wheel clogging and workpiece material adhesion.Finally,an analytical model for prediction of the grinding ratio was established by combining the tool wear volume,grinding force,and grinding length.The acceptable errors between the predicted and experimental grinding ratios(ranging from 0.6 to 1.8)were 7.56%and 6.31%for the BA and MA abrasive wheels,respectively.This model can be used to evaluate quantitatively the grinding performance of an alumina abrasive wheel,and is therefore helpful for optimizing the grinding parameters in the creep feed grinding process.
文摘As is known to all, grinding force is one of the most important parameters to evaluate the whole process of grinding. Generally, the grinding force is resolved to three component forces, namely, normal grinding force F n, tangential grinding force F t and a component force acting along the direction of longitudinal feed which is usually neglected because of insignificance. The normal grinding force F n has influence upon surface deformation and roughness of workpiece, while the tangential grinding force F t mainly affect power consumption and service life of grinding wheel. In order to study deep into the process of the unsteady state grinding, we set up a measurement system to monitor the change of grinding force during the course of grinding and try to find some difference in the change of grinding force between the steady state grinding and unsteady state grinding. In the test, the normal and tangential grinding forces, F n and F t were measured by using a set of equipments including sensor, amplifier, oscilloscope and computer monitor. From the results, we can conclude that: 1) In the unsteady state grinding process, the values of the grinding forces are much lower than those of the steady state grinding process and the grinding force ratio showed a nonlinear fluctuation. 2) The tendency of the grinding forces in the process of the unsteady state grinding proved the existence of the cutting and micro-cutting actions. 3) Because the grinding force signals of the unsteady state grinding are much weaker than those of the steady state grinding, to obtain accurate value of the grinding forces, wave filtering is needed to be done. The whole process to filter the perturbation wave can be separated into three steps in order, changing the grinding force signals from analog signals into digital signals, FFT (fast Fourier transform) treatment to the digital signals, and IFFT(inversion fast Fourier transform) treatment to the digital signals after spectrum limitation.
文摘In conventional grinding theory, it is obvious that there must be a very high hardness difference between grains of the grinding wheel and workpieces. The best grinding wheels are those giving the lowest "natural limiting surface roughness" while cutting at appreciable plunge velocities. With the development of new materials and new machining processes, conventional theories of grinding techniques are no longer suitable to explain many phenomena in the course of grinding procedures. In dealing with precision or ultra-precision grinding processes of advanced ceramics, many results of experiments and practical production have shown that grinding with super hard materials wheels is not the only method to machine advanced ceramics. This paper is intended to propose a new grinding theory named as unsteady-state grinding technique evolved from some phenomena that can not be explained by conventional grinding theory. Unsteady-state grinding technique means the technique which can make the surface roughness of the materials, especially hard and brittle, be up to the standard of ultra-precision machining by utilizing common wheels characteristic of inferior self-sharpening and wear-resistance. In the process of machining, the common wheel need to be redressed about 3～5 times and the time between two redressings is about 3～5 minutes. As a validation of the new grinding technology, experimental work was performed to prove the existence of the unsteady state in the process of ultra-precision grinding with common abrasive wheel-pink fused alumina wheel. From the results of the observation of the wheel topography, the whole grinding process in unsteady state was separated into three stages namely cutting by grains peaks, micro-cutting by micro edges of the broken grains and rubbing without material removal, which is different from conventional grinding theory. For the difference of hardness between grinding wheel and workpiece material is not so apparent, some people have doubts about whether the cutting especially micro-cutting actions exist in the process of unsteady state grinding. By utilizing the common abrasive wheel newly redressed to grind the finished surface of silicon nitride glut and comparing the finished surface with the damaged surface in SEM pattern and surface roughness, the existence of cutting and micro- cutting actions in the unsteady state grinding process was confirmed.
