基于Digital Micrograph的Ti(C,N)基金属陶瓷材料定量金相分析

Ti(C,N)基金属陶瓷显微组织及相界面较复杂,需要一种简便、精确的定量金相方法来辅助研究.采用功能强大的Gatan Digital Micrograph软件对不同纳米添加量Ti(C,N)基金属陶瓷显微组织进行背底消除、滤波、二值化及图像形态学处理,分析可得到该金相图中的一些金相特征参数.对不同纳米添加量Ti(C,N)基金属陶瓷中硬质相进行了综合分析,结果表明,利用Gatan Digi-tal Micrograph软件实现Ti(C,N)基金属陶瓷显微组织的分析测量是完全可行的,能有效地提高工作效率及得到直观、准确的结果,也可定量地得到随纳米粉添加量的不断增加,硬质相颗粒的总体积不断减少,平均粒径也在不断减小.

Liberation characteristics of coal middlings comminuted by jaw crusher and ball mill

The associated minerals make coal middlings possess a relatively high ash content.Subsequent liberation through size reduction can cause recovery increase.However,effect of comminution facilities on mineral liberation of middlings was ignored.This paper studied the liberation characteristics of middlings crushed with different kinds of fragmentation forces.Middlings of 3 mm+0.5 mm sampled from a dense medium cyclone were comminuted by a jaw crusher and a ball mill to 0.5 mm with similar size distribution respectively.The generating mechanism of fnes was also analyzed.Full densimetric analyses indicate that mineral liberation of the product crushed by the jaw crusher is better than that by the ball mill at each fraction.For sizes of 0.125 mm+0.074 mm and 0.074 mm,yields of the product with ash content 11%comminuted by jaw crusher are nearly 20%higher than that by the ball mill.Sectional micrographs observed by the scanning electron microscopy(SEM)also show the same law for these two fractions and some intergrowth particles still exist in the fraction of 0.5 mm+0.25 mm.

Surface characteristics analysis of fractures induced by supercritical CO_(2)and water through three-dimensional scanning and scanning electron micrography

Morphology of hydraulic fracture surface has significant effects on oil and gas flow,proppant migration and fracture closure,which plays an important role in oil and gas fracturing stimulation.In this paper,we analyzed the fracture surface characteristics induced by supercritical carbon dioxide(SC-CO_(2))and water in open-hole and perforation completion conditions under triaxial stresses.A simple calculation method was proposed to quantitatively analyze the fracture surface area and roughness in macro-level based on three-dimensional(3D)scanning data.In micro-level,scanning electron micrograph(SEM)was used to analyze the features of fracture surface.The results showed that the surface area of the induced fracture increases with perforation angle for both SC-CO_(2)and water fracturing,and the surface area of SC-CO_(2)-induced fracture is 6.49%e58.57%larger than that of water-induced fracture.The fractal dimension and surface roughness of water-induced fractures increase with the increase in perforation angle,while those of SC-CO_(2)-induced fractures decrease with the increasing perforation angle.A considerable number of microcracks and particle peeling pits can be observed on SC-CO_(2)-induced fracture surface while there are more flat particle surfaces in water-induced fracture surface through SEM images,indicating that fractures tend to propagate along the boundary of the particle for SC-CO_(2)fracturing while water-induced fractures prefer to cut through particles.These findings are of great significance for analyzing fracture mechanism and evaluating fracturing stimulation performance.

Transformation toughening of Al_2O_3/ZrO_2 laminated ceramics with residual compressive stress

With the help of scanning electronic microscopy and X-ray diffraction, the relationships of microstructure characteristics, phase assemblage, and fracture micrograph of Al2O3/ZrO2 laminated ceramics were studied. Compared with monolithic Al2O3/ZrO2 ceramics, the existence of surface compressive stresses greatly restrained the growth of ZrO2 and Al2O3 grains at high sinter temperature, fined the grain size, and increased the content of metastable t-ZrO2, which made the fracture transformation energy quantity 70% higher than that of the monolithic ceramics. The trans-granular and inter-granular fracture features were observed in the surface and center layers, which further verified that transformation toughening is the main mechanism, whereas, micro-crack toughening is helpful for enhancing fracture toughness.

Dermatofibrosarcoma protuberans: from translocation to targeted therapy

Dermatofibrosarcoma protuberans(DFSP), the most common dermal sarcoma, is a low-grade, slow growing fibroblastic malignant neoplasm that most frequently affects middle aged adults and is characterized by a high local recurrence rate and a low propensity for metastasis. Wide surgical resection or Mohs micrographic surgery(MMS) are the preferred approaches for localized disease, while radiation therapy is warranted for inoperable disease or for cases with positive margins where re-excision is not possible. DFSP is generally regarded as refractory to conventional chemotherapy. Treatment options for systemic disease were limited until the discovery of a unique translocation, t(17;22)(q22;q13)(COL1A1;PDGFB) found in a majority of cases. In recent years, imatinib, a PDGFβR, ABL and KIT inhibitor, has revolutionized systemic therapy in DFSP. In this review, we summarize the epidemiological, clinical, histological and genetic characteristics of DFSP and update the readers on its current management.

Three-Dimensional Reconstruction of Icosahedral Virus by Symmetry-Adapted Functions

A three-dimensional （3D） reconstruction of icosahedral virus is carried out by the icosahedral symmetry-adapted function （ISAF） method in spherical coordinates. In order to reduce the influence of noise, it is better to use the basis functions that have identical symmetry with the object reconstructed. It is verified that the ISAF method has stronger ability to reduce the influence of noise to grain the resolution better than that of the conventional method by the simulation of 3D reconstruction.

Non-monotonic influence of a magnetic field on the electrochemical behavior of Fe_(78)Si_9B_(13) glassy alloy in NaOH and NaCl solutions

The corrosion behavior and microstructure of Fe78Si9B13 glassy alloy in NaOH and NaCl solutions under a 0.02-T magnetic field were investigated through electrochemical testing and scanning electron microscopy （SEM）. The current-density prepeak （PP） in the anodic polarization curves in low-concentration NaOH solutions （classified as type I） tends to disappear when the NaOH concentration is increased to 0.4 mol/L and the magnetic field is applied. Under the magnetic field, the height of the second current-density peak is increased in low-concentration NaOH solutions （type I） but decreased in high-concentration NaOH solutions （type Ⅱ）. The non-monotonic effect of the magnetic field was similarly observed in the case of polarization curves of samples measured in NaCl solutions, Ring-like corroded patterns and round pits are easily formed under the magnetic field in NaOH and NaC1 solutions. These experimental results were discussed in terms of the magnetohydrodynamic （MHD） effect.

Activity of chlorpromazine on nfa1 and Mp2CL5 genes of Naegleria fowleri trophozoites

Amoeba treatment of patients suffering from pri-mary amoebic meningoencephalitis caused by Naegleria fowleri has not been successful. Dam-aged morphology and effect on genes of N. fowleri as the result of its initial interaction with drug may provide clue to the success of treatment. In this study, we investigated the activity of chlorpromazine compared with amphotericin B and voriconazole against N.fowleri Khon Kaen strain using cell based assay and molecular techniques. Scanning electron and light micro-graph showed the drug interaction of treated amoebae with 0.098 ug/ml chlorpromazine was faster than 0.002 ug/ml amphotericin B and 12.5 ug/ml of voriconazole. The morphological cha-racteristics of treated amoebae with Gomori’s trichrome stain correlated to the scanning elec-tron microscope study. The effect of drugs to nfa1 and Mp2CL5 genes of treated amoebae found that at 120 min post exposure, chlorpromazine, voriconazole inhibited both genes except amphotericin B. Most of drug inhibited nfa1 except fluconazole. The results evaluated that chlorpromazine was higher potency and rapidly activity than amphotericin B and voriconazole against N. fowleri trophozoites.

Structural and Electrical Characteristics of Ba(Fe_0.5Nb_0.5)O₃-SrTiO₃Ceramic System

A complex structure of barium iron niobate, Ba(Fe0.5Nb0.5)O3 (BFN) and strontium titanate SrTiO3 (ST) was fabricated by a solid-state reaction method. The phase formation of Ba(Fe0.5Nb0.5)O3-SrTiO3 was checked using X-ray diffraction (XRD) technique. The X-ray structural analysis of BFN and BFN-ST ceramics, showed the formation of single-phase compound in the monoclinic system, which is a distorted structure of an ideal cubic perovskite. Careful examination of microstructures of the individual compounds of the system was done by the scanning electron micrograph (SEM), and confirms the polycrystalline nature of the systems. Detailed studies of dielectric and electrical impedance properties of the systems in a wide range of frequency (100Hz - 5MHz) and different temperatures (30°C-285°C) showed that these properties are strongly dependent on temperature and frequency.

Dielectric Relaxation in Complex Perovskite Oxide Sr(Gd_0.5Nb_0.5)O₃

The complex perovskite oxide a strontium gadolinium niobate (SGN) synthesized by solid-state reaction technique has single phase with tetragonal structure. X-ray diffraction (XRD) technique and scanning electron microscopy (SEM) were used to study the structural and microstructural properties of the ceramics, respectively. The XRD patterns of SGN at room temperature show a tetragonal structure. Studies of the dielectric constant and dielectric loss of compound as a function of frequency (50 Hz to 1 MHz) at room temperature, and as a function of temperature (60°C to 420°C) indicate polydispersive nature of the material. The logarithmic angular frequency dependence of the loss peak is found to obey the Arrhenius law with activation energy ~0.18 eV. The small value of activation energy of the compound (~0.18 eV) can be explained by mixed ionic-polaronic conductivity mechanism. The grain size of the pellet sample was found to be 1.92 μm. The frequency-dependant electrical data are analyzed in the framework of conductivity and electric modulus formalisms. The complex plane impedance plot shows the grain boundary contribution for higher value of dielectric constant in the law frequency region.

Scanning Electron Micrographic Investigation of Explanted (Used) Metallic Biomedical Implants for Corrosion and Other Mechanical Damage Responsible for Failure

This paper deals with detailed corrosion analysis of explanted devices. The study of total 6 different types of orthopedic metallic implant was carried out after collecting the clinical report from the doctors, who performed these implantations. The clinical report covered the purpose of implantation, body part where implantation was done, and physiological reasons of removal of implant. The metallurgical investigation to study corrosion and any other mechanical damage to the implant surface during their service period was done using the Scanning Electron Micrography. SEM presented in this paper reveals the presence of in-vitro corrosion and mechanical damage as well, which are corroborating well with clinical reports.

Reconstruction of Chin Defects Using an O to Z Bilateral Rotation Flap

Reconstruction of defects on the chin represents a challenge given the functional, multidirectional movement of the chin subunit. In this article, we describe the surgical technique of a bilateral O to Z rotation flap on the chin, as well as complications, cosmetic outcome, and patient satisfaction. A retrospective chart review from January 2009-June 2011 identified twelve patients where an O to Z flap was used to repair a surgical defect. Of the twelve patients identified, one patient had a presumed post-operative infection, and one patient required additional corrections. There were no complications of hematomas or flap necrosis. Overall patient cosmetic outcome was excellent. An O to Z closure is an option for chin reconstruction of small to medium defects that offers a satisfactory cosmetic outcome, high patient satisfaction and low complication rate.

Adverse Effects of Permanent Waving and Hair Relaxation—Assessment by Scanning Electron Microscopy (SEM)

Permanent waving is very popular in Japan. Polypeptide chains (main chains) form the principal components of hair, and they are lined up longitudinally. Hair relaxation is also called straight permanent waving, and there are methods that change curly or wavy hair into straight hair. Hair damage as a result of winding, combing, and using high-temperature hairdressing irons is also often seen. By using scanning electron micrographs (SEM) we showed broken hairs and hair damage caused by permanent wave solutions. The hair damage is obvious when comparisons are made with the condition of the hair surface, condition of the cuticle, etc. Hair swelling by permanent wave solutions, manipulations such as winding, etc., inadequate rinsing with water, procedures on injured hair at the outset, etc., are considered possible reasons for any of these types of injury.

Influence of Sn Low Doping on the Morphological, Structural and Optical Properties of ZnO Films Deposited by Sol Gel Dip-Coating

In this work, Undoped Zinc Oxide (ZnO) and Sndoped Zinc Oxide (ZnO:Sn) films have been deposited by sol-gel dip coating method, where the Sn/Zn atomic ratio was 3% and 5% in the solution. The effects of Sn incorporation on morphological, structural and optical properties of ZnO films were investigated. The Scanning Electron Microscopy (SEM) showed that the morphological surface of the films was affected by Sn low doping. The X-Ray Diffraction (XRD) patterns showed that all films have polycrystalline structures, and the doping incorporation has not lead to substantial changes in the structural characteristics of ZnO films. The crystallite size was calculated using the well-known Scherrer’s formula and found to be in the range of 23 - 40 nm. The measurements from UV-Visible Spectrophotometer (U-Vis) indicated that the highest average optical transmittance in the visible region was related to Undoped ZnO film, then the optical band gap and Urbach energy values of thin films were calculated. The X-Ray Photoelectron Spectroscopy (XPS) has demonstrated that Sn is incorporated in ZnO lattice.

Texture ZnO Thin-Films and their Application as Front Electrode in Solar Cells

In this paper, three kinds of textured ZnO thin-films (the first kind has the textured structure with both columnar and polygon, the second posses pyramid-like textured structure only, and the third has the textured structure with both crater-like and pyramid-like), were prepared by three kinds of methods, and the application of these ZnO thin-films as a front electrode in solar cell was studied, respectively. In the first method with negative bias voltage and appropriate sputtering parameters, the textured structure with columnar and polygon on the surface of ZnO thin-film are both existence for the sample prepared by direct magnetron sputtering. Using as a front electrode in solar cell, the photoelectric conversion efficiency Eff of 7.00% was obtained. The second method is that by sputtering on the ZnO:Al self-supporting substrate, and the distribution of pyramid-like was gained. Moreover, the higher (8.25%) photoelectric conversion efficiency of solar cell was got. The last method is that by acid-etching the as-deposited ZnO thin-film which possesses mainly both columnar and polygon structure, and the textured ZnO thin-film with both crater-like and pyramid-like structure was obtained, and the photoelectric conversion efficiency of solar cell is 7.10% when using it as front electrode. These results show that the textured ZnO thin-film prepared on self-supporting substrate is more suitable for using as a front electrode in amorphous silicon cells.

Structural Features and Properties of the Vitreous Part of the System 50P₂O₅-25CaO-(25-x)Na₂O-xCoO (with 0 ≤ x ≤ 25;mol%)

The glass series 50P2O5-25CaO-(25-x)Na2O-xCoO (with (0 ≤ x ≤ 25;mol%), has been prepared by direct melting at 1080°C ± 20°C. The introduction of cobalt in calcium phosphate glasses is used to compare its effect with calcium in inhibition corrosion. The dissolution rate has been investigated. It indicated an improvement of chemical durability when the cobalt oxide increases in the network glass at the expense of Na2O content. Both, IR spectroscopy and X-ray diffraction have confirmed the structure changes when the CoO content increases in the glass. This change results in the disappearance of isolated orthophosphate groups followed of a polymerizing of the structure from isolated orthophosphate towards pyrophosphate chains (Q1) by promoting the formation of olygophosphates (mixed Q1-Q2) rich in pyrophosphates. Analysis of the density values, showed an increase of density with the increase CoO content. The covalent radius values of oxygen rcal (O2-) indicate a significant decrease and therefore a relatively high reinforcement of the metal-oxygen-phosphorus (Co-O-P) bonds. SEM micrograph confirms the evolution of the glass structural morphology. The sample having a maximum CoO content confirms a homogeneous glass phase with quite crystalline particles. This property is prerequisite for many interesting industrial applications.

Effect of Fiber Weight Ratio and Fiber Modification on Flexural Properties of Posidonia-Polyester Composites

The main objective of this research is to study the effect of fiber weight ratio and chemical fiber modification on flexural properties of composites reinforced with Posidonia fiber. An unsaturated polyester matrix reinforced with untreated and treated Posidonia fibers was fabricated under various fiber weight ratios. Results showed that the combined chemical treatment provided better mechanical properties of composites in comparison with untreated fiber. The fiber weight ratio influenced the flexural properties of composites. Indeed, a maximum value of flexural modulus was observed for 10% fiber weight ratio for composites reinforced with treated fibers. SEM photographs revealed a different fracture surface between Posidonia fibers reinforced polyester composites.

Study on growth and properties of novel γ-LiAlO_2 substrate

Transparent γ-LiAlO2 single crystal has been grown by Temperature Gradient technique. The surface of the wafer annealed in O2-atmosphere at 1100°C for 70 h became opaque and Li-poor phase (LiAl5O8); while, that annealed in Li-rich atmosphere kept transparent and smooth. The full-width at half maximum value dropped to 30 arcsecs when the wafer was annealed in Li-rich atmosphere. That annealed in O2-atmosphere increased to 78 arcsec. Compared with absorption spectra, we can conclude that the 196 nm absorption peak was caused by Li vacancies and the 736 nm peak was caused by O vacancies.

Fast-growing procedure for perovskite films in planar heterojunction perovskite solar cells

A fast-growing procedure（FGP） to fabricate perovskite films with large grain sizes is described in this article. In the FGP method, the perovskite precursor solution is coated onto the substrates at a temperature of 240 8C. The solvent in the precursor solution evaporates quickly in about 2 s, resulting in the rapid formation of a perovskite film without further annealing process. Millimeter-scale perovskite grain clusters are obtained in the film. Based on such perovskite films, fabricated planar heterojunction perovskite solar cells give a power conversion efficiency（PCE） above 8%.

Investigation on the Electrochemical Polymerization of Catechol by Means of Rotating Ring-disk Electrode

The electrolysis of catechol was studied in the pH values of 1 to 10. The results from the rotating ring disk electrode (RRDE) experiments show that at low pH values, the electrochemical polymerization of catechol was performed by one step, and at higher pH values, the electrochemical polymerization of catechol was carried out by two steps, i.e . oxidation of catechol and followed by polymerization. The intermediates generated at the disk were detected at the ring electrode in the ring potential region of -0.2 to 0 V (vs. Ag/AgCl). One of reasons for the decrease in the ratio of i r to i d with increasing the ring potential is caused by formation of positively charged intermediates at the disk electrode. This ratio increases with increasing the rotation rate of the RRDE, which indicates that the intermediates are not stable. A shielding effect during polymerization of catechol was observed when the ring potential was set at 0.1 V (vs. Ag/AgCl). The electron spin resonance (ESR) of polycatechol shows that polycatechol possesses unpaired electrons. The images of polycatechol films synthesized at different conditions are described.