The Chinese skeleton: insights into microstructure that help to explain the epidemiology of fracture

Osteoporotic fractures are a major public health problem worldwide, but incidence varies greatly across racial groups and geographic regions. Recent work suggests that the incidence of osteoporotic fracture is rising among Asian populations. Studies comparing areal bone mineral density and fracture across races generally indicate lower bone mineral density in Asian individuals including the Chinese, but this does not reflect their relatively low risk of non-vertebral fractures. In contrast, the Chinese have relatively high vertebral fracture rates similar to that of Caucasians. The paradoxically low risk for some types of fractures among the Chinese despite their low areal bone mineral density has been elucidated in part by recent advances in skeletal imaging. New techniques for assessing bone quality non-invasively demonstrate that the Chinese compensate for smaller bone size by differences in hip geometry and microstructural skeletal organization. Studies evaluating factors influencing racial differences in bone remodeling, as well as bone acquisition and loss, may further elucidate racial variation in bone microstructure. Advances in understanding the microstructure of the Chinese skeleton have not only helped to explain the epidemiology of fracture in the Chinese, but may also provide insight into the epidemiology of fracture in other races as well.

Effect of Post Weld Heat Treatment on Microstructure and Fracture Toughness of Friction Welded Joint

The effect of post weld heat treatment on the microstructure and fracture toughness of friction welded joints of Ti-6.5Al-1Mo-1V-2Zr alloy was studied. The experimental results show that equiaxial grains were formed at the center of the weld metal while highly deformed grains were observed in the thermomechanically affected zone. The fracture toughness of the weld metal was lower than that of the thermomechanically affected zone under as-weld and post weld heat treatment conditions. With increasing temperature of post weld heat treatment, the fracture toughness of weld center and thermomechanically affected zone increased. The fractographic observation revealed that the friction welded joints fractured in a ductile mode.

Fracture behavior and microstructure analysis of Al2O3–MgO–CaO castables for steel-ladle purging plugs

Three different castables based on the Al_2O_3–MgO –CaO system were prepared as steel-ladle purging plug refractories： corundum-based low-cement castable（C-LCC）, corundum-spinel-based low-cement castable（C-S-LCC）, and corundum-spinel no-cement castable（C-S-NCC）（hydratable alumina（ρ-Al_2O_3） bonded）. The fracture behavior at room temperature was tested by the method of ＂wedge-splitting＂ on samples pre-fired at different temperatures; the specific fracture energy G′f and notched tensile strength σNT were obtained from these tests. In addition, the Young＇s modulus E was measured by the method of resonance frequency of damping analysis（RFDA）. The thermal stress resistance parameter R′′′′ calculated using the values of G′f, σNT, and E was used to evaluate the thermal shock resistance of the materials. According to the microstructure analysis results, the sintering effect and the bonding type of the matrix material were different among these three castables, which explains their different fracture behaviors.

MECHANICAL PROPERTIES OF FINE PITCH DEVICES SOLDERED JOINTS BASED ON CREEP MODEL

Nonlinear analyses of quad flat package （QFP） on printed circuit board （PCB） assemblies subjected to thermal cycling conditions are presented. Two different solders are considered, namely, Sn37Pb and Sn3.5Ag. The stress and strain response of fine pitch devices soldered joints was investigated by using finite element method based on Garofalo-Arrheninus model. The simulated results indicate creep distribution of soldered joints is not uniform, the heel and toe of soldered joints, the area between soldered joints and leads are the creep concentrated sites. The similar phenomena of stress curves simulated based on Garofalo-Arrheninus model and Anand equations is confirmed, and the creep strain value of Sn3.5Ag soldered joints is lower than that of Sn37Pb soldered joints. Thermal cycling results show that Sn3.5Ag strongly outperforms Sn37Pb for QFP devices under the studied test condition. This is well matched with the experimental outcome analyzed. In addition, the soldered devices were tested by micro-joints tester, the tensile strength of Sn3.5Ag soldered joints is found to be higher than that of Sn37Pb soldered joints. By analyzing the fracture microstructure of soldered joints, it is found that fracture mechanism of Sn3.5Ag soldered joints is toughness fracture, while fracture mechanism of Sn37Pb soldered joints includes brittle fracture and toughness fracture. The results of this study provide an important basis of understanding the mechanical properties of fine pitch devices with traditional Sn37Pb and Sn3.5Ag lead-free soldered joints.

Low-cycle Fatigue Behavior of Ni-based Superalloy GH586 with Laser Shock Processing

Low-cycle fatigue behavior of Ni-based superalloy GH586 with laser shock processing（LSP） was investigated. The residual stress of the specimens treated with LSP was assessed by X-ray diffraction method. The microstructure and fracture morphology were characterized by using an optical microscope（OM）, a scanning electron microscope（SEM）, and a transmission electron microscope（TEM）. The results indicated that the maximum residual compressive stress was at about 1 mm from the shocking spot center, where the residual compressive stress was slightly lower. High density tangling dislocations, dislocation walls, and dislocation cells in the microstructure of the specimens treated with LSP effectively prevented fatigue cracks propagation. The fatigue life was roughly twice as long as that of the specimens without LSP. The fatigue crack initiation（FCI） in specimens treated with LSP was observed in the lateral section and the subsurface simultaneously. The fatigue striation in the fracture treated with LSP was narrower than that in the untreated specimens. Moreover, dimples with tear ridges were found in the fatigued zones of the LSP treated specimens, which would be caused by severe plastic deformation.

Microstructure and mechanical properties of Ni3Al intermetallics prepared by directional solidification electromagnetic cold crucible technique

The present work focused on the Ni_3Al-based alloy with a high melting point. The aim of the research is to study the effect of withdrawal rate on the microstructures and mechanical properties of directionally solidified Ni-25 Al alloy. Ni_3 Al intermetallics were prepared at different withdrawal rates by directional solidification(DS) in an electromagnetic cold crucible directional solidification furnace. The DS samples contain Ni_3 Al and Ni Al phases. The primary dendritic spacing(λ) decreases with the increasing of withdrawal rate(V), and the volume fraction of Ni Al phase increases as the withdrawal rate increases. Results of tensile tests show that ductility of DS samples is enhanced with a decrease in the withdrawal rate.

Semisolid die forging process,microstructures and properties of AZ31 magnesium alloy mobile telephone shells

A semisolid slurry of AZ31 magnesium alloy was prepared by vibrating wavelike sloping plate process,and the semisolid die forging process,microstructures,and properties of the magnesium alloy mobile telephone shell were investigated.The semisolid forging process was performed on a YA32-315 four-column universal hydraulic press.The microstructures were observed by optical microscopy,the hardness was analyzed with a model 450SVD Vickers hardometer,the mechanical properties was measured with a CMT5105 tensile test machine,and the fractograph of elongated specimens was observed by scanning electron microscopy （SEM）.The results reveal that with the increase of die forging force,the microstructures of the product become fine and dense.A lower preheating temperature and a longer dwell time are favorable to the formation of fine and dense microstructures.The optimum process conditions of preparing mobile telephone shells with excellent surface quality and microstructures are a die forging force of 2000 kN,a die preheating temperature of 250℃,and a dwell time of 240 s.After solution treatment at 430℃ and aging at 220℃ for 8 h,the Vickers hardness is 61.7 and the ultimate tensile strength of the product is 193MPa.Tensile fractographs show the mixing mechanisms of quasi-cleavage fracture and ductile fracture.

Microstructure and Fracture Behavior of 316L Austenitic Stainless Steel Produced by Selective Laser Melting

Selective laser melting is an additive manufacturing method based on local melting of a metal powder bed by a high power laser beam. Fast laser scans are responsible for severe thermal gradients and high cooling rates which produce complex hydrodynamic fluid flow. These phenomena affect crystal growth and orientation and are believed to be the cause of material spattering and microstructural defects, e.g. pores and incompletely melted particles. In this work, the microstructure and texture of 316L bars built along two different orientations and the effect of different distribution of defects on their mechanical response and failure mechanisms were investigated. Partially molten powder particles are believed to be responsible for the scattering in elongation to failure, reduced strength, and premature failure of vertical samples.

Mechanical Properties and Fracture Behavior of Mg-Al/AlN Composites with Different Particle Contents

In this study, magnesium matrix composites reinforced with different loading of AlN particles were fabricated by the powder metallurgy technique. The microstructure, bending strength and fracture behavior of the resulting Mg-Al/Al N composites were investigated. It showed that the 5 wt% AlN reinforcements led to the highest densification and bending strength. The total strengthening effect of AlN particles was predicted by considering the contributions of CTE mismatch between the matrix and the particles,load bearing and Hall-Petch mechanism. The results revealed that the increase of dislocation density,the change of Mg17Al12 phase morphology, and the effective load transfer were the major strengthening contributors to the composites. The fracture of the composites altered from plastic to brittle mode with increasing reinforcement content. The regions of clustered particles in the composites were easy to be damaged under external load, and the fracture occurred mainly along grain boundaries.

Evaluation on Fatigue Performance and Fracture Mechanism of Laser Welded TWIP Steel Joint Based on Evolution of Microstructure and Micromechanical Properties

The fatigue performance and fracture mechanism of laser welded twinning induced plasticity（TWIP）steel joint were investigated experimentally based on the evolution of microstructure and micromechanical properties.The optical microscopy was used to analyze the evolution of microstructure.The variation of composition and phase structure of fusion zone were detected by energy dispersive X-ray and X-ray diffraction spectrometers.The micromechanical behaviors of the various zones were characterized using nanoindentation.The static tensile test and high cycle fatigue test were performed to evaluate the mechanical properties of welded joint and base metal.The microstructures,tensile properties and fatigue strength of base metal as well as welded metal were analyzed.The fatigue fracture surfaces of base metal and welded joint were observed by means of scanning electron microscopy,in order to identify fatigue crack initiation sites and propagation mechanisms.Moreover,the fatigue fracture characteristics and mechanisms for the laser welded TWIP steel joints were analyzed.

Influence of Vanadium on Fracture Splitting Property of Medium Carbon Steel

The fracture splitting property of medium carbon steel 37MnSiS microalloyed with V up to 0. 45% was investigated by using simulated fracture splitting test,for the development of new crackable medium carbon steel to manufacture high performance connecting rod. Conventional high carbon steel C70S6 was used for comparison. The results show that the volume fraction of both ferrite and V-rich M（ C,N） particles increases,and the pearlite interlamellar spacing decreases with increasing V content,which in turn results in gradual increase of strength and decrease of ductility and impact energy. The fracture splitting property of the tested steel could be improved significantly due to the increase of V content mainly through the precipitation hardening mechanism of fine M（ C,N） precipitates. The fraction of brittle cleavage fracture in the crack initiation area increases noticeably with increasing V content and full brittle cleavage fracture surface could be obtained when V content was increased to 0. 45%. It is concluded that medium carbon steel with V content higher than about 0. 28% possesses not only comparable or even higher mechanical properties with those of conventional steel C70S6,but also excellent fracture splitting property,and therefore,is more suitable to fabricate high performance fracture splitting connecting rod.

Effect of boron addition on the microstructures and mechanical properties of thermomechanically processed and tempered low carbon bainitic steels

Thermomechanical process and tempering heat treatment were employed to produce the experimental steel plates. The effect of boron addition on the microstructure and mechanical properties of low carbon bainitic steels was studied in this paper. Microstructure observation and crystallographic features were conducted by using optical microscopy, SEM, TEM and electron back scattering diffraction （EBSD） analysis. The results showed that under the same rolling processes and heat treatment conditions, a substantial increase in strength is obtained by addition of boron into steel, but accompanied by an obvious drop in toughness. New martensite phase forms along the grain boundaries on tempering at 650℃ mainly due to boron segregation, which can further deteriorate impact toughness of the boron bearing steel. The EBSD analysis showed that high angle grain boundary, is not responsible for the deteriorated toughness of the boron bearing steel because it has relatively higher percentage of high angle grain boundary than the boron free steel. The low toughness of the boron bearing steel is mainly attributed to the coarse boride precipitated particles according to the results of fractograph observation.

Microstructure and tensile behavior of 2D-C_f/AZ91D composites fabricated by liquid–solid extrusion and vacuum pressure infiltration

2D carbon fiber reinforced AZ91 D matrix composites（2D-C_f/AZ91 D composites） were fabricated by liquid–solid extrusion and vacuum pressure infiltration technique（LSEVI）. In order to modify the interface between fibers and matrix and protect the fiber, pyrolytic carbon（Py C） coating was deposited on the surface of T700 carbon fiber by chemical vapor deposition（CVD）. Microstructure observation of the composites revealed that the composites were well fabricated by LSEVI. The segregation of aluminum at fiber surface led to the formation of Mg_（17）Al_（12） precipitates at the interface. The aluminum improved the infiltration of the alloy and Py C coating protected the fibers effectively. The ultimate tensile strength of 2D-C_f/AZ91 D composites was about 400 MPa. The fracture process of 2D-C_f/AZ91 D composites was transverse fiber interface cracking–matrix transferring load–longitudinal fibers bearing load–longitudinal fibers breaking.

Understanding Fatigue Failure in Binary Rubber Blends: Role of Crack Initiation and Propagation

Under cyclic loading conditions,the breakdown of rubber products is mainly caused by the formation and spread of cracks.This study focuses on understanding how cracks initiate and grow during the fatigue failure of blended rubber.We prepared composite materials by blending bio-mimetic rubber (BMR);butadiene rubber (BR) in different mass ratios and evaluated their resistance to crack initiation and propagation.Our results indicate a clear trend: as the BR content increases,crack initiation in blended rubber is inhibited,while crack propagation is enhanced.This shift leads to a change in the primary factor influencing fatigue fracture from crack initiation to crack propagation.Additionally,we observed that the fatigue life of the rubber blend initially increases and then decreases as the BMR content rises,indicating a critical threshold when the mass ratio of BMR to BR is comparable.By closely examining the materials using a scanning electron microscope (SEM);image analysis,we confirmed that before the threshold,crack initiation is the dominant factor in fatigue failure,while after the threshold,crack propagation takes over.This study provides valuable insights into the mechanisms behind fatigue failure in rubber blends,contributing to a better understanding of this important material behavior.