Manufacture of Zn-Co Substituted Y-Type Barium Hexagonal Ferrites by Citrate Precursor Route and Their Microwave Properties

Ba2ZnxCo2-xFe12O22 hexaferrites with x = 0.0, 0.4, 0.8, 1.2, 1.6 and 2.0 were prepared by citrate sol-gel process. The complex dielectric constant and complex permeability of hexaferrites were studied as functions of the measuring frequency, composition and sintering temperature in the range 100 MHz similar to 6 GHz. The natural resonance phenomenon is observed in mu' spectrum for all Y-type hexaferrites, which resonance frequency is dependent on zinc content and firing temperature. The natural resonance frequencies Of Co2Y hexaferrite were calculated, which is in agreement with the measuring results. The reflection loss of those ferrites is measuring frequency as well as absorber thickness dependent, and the higher the frequency and the thickness are, the higher the reflection loss is.

Natural Rubber Based Composites Comprising Different Types of Carbon-Silica Hybrid Fillers. Comparative Study on Their Electric, Dielectric and Microwave Properties, and Possible Applications

The paper presents a comparative study on the electric, dielectric and microwave properties of natural rubber based composites comprising dual phase fillers prepared from furnace carbon black or conductive carbon black with a different amount of silica. It has been established that, the specifics of the carbon phase have a marked strong effect upon the properties mentioned above. The interpenetration of the two filler phases and the grade of isolation of the conductive carbon phase by the dielectric one depend on the ratio between them. On the other hand, that leads to a change in all properties of the studied composites, which allows tailoring those characteristics.

Microwave properties and surface topography of soft magnetic films with high resistivity

A single layer of CoFeB and a multilayer of CoFeB MgO films are prepared by means of DC/RF magnetron sputter deposition. The excellent microwave properties and high electrical resistivity are simultaneously achieved in the discontinuous multilayer structure of [Co44Fe44B12（0.7nm）/MgO（0.4nm）]40 film. This film has a high permeability （μ′） （larger than 100 below 2.1 GHz）, a high magnetic loss （μ″） （larger than 100 in a range from 1.5 to 3.3GHz）, a resistivity of 3.3 × 10^3μΩ. cm, a saturation magnetization of 1.2 T, and an in-plane uniaxial anisotropy field of 5.5 kA/m. The microstructure and the surface topography of the film are also analysed. The relatively large surface roughness for the discontinuous film is responsible for the wide frequency band of magnetic loss. The magnetic loss and the high resistivity indicate that the discontinuous CoFeB MgO multilayer film has potential applications in microwave absorbers and electromagnetic interference （EMI） shielding materials in a GHz frequency range.

STUDY ON PREPARATION, COMPLEX PERMITTIVITY,PERMEABILITY AND MICROWAVE PROPERTIES OF BaZnzCo(2-z)Fe16O27/SiO2 MICROCRYSTALLINE GLASS CERAMICS

BaZnzCo2-zFe16O27/SiO2 microcrystalline glass ceramics with Z=0.0, 0.5, 0.8 and 1.1 were prepared at temperature 1200℃ for 5h by citrate sol-gel process. The complex dielectric constant and complex permeability of BaZnzCo2-zFe16 O27/SiO2-paraffin wax composites had been measured. Both the complex dielectric constant and dielectric loss exhibit almost no variation with frequency in 0.1-6.0GHz. The real part of permeability decreases with increasing frequency for all samples, and the imaginary part of permeability exhibits a clear resonance peak at 1.44GHz for Co2 W/SiO2, 1.32GHz for Zn0.5Co1.5 W/SiO2, 1.20GHz for Zn0.8Co1.2W/SiO2, and 1.08GHz for Zn1.1 Co0.9 W/SiO2. It is also showed that the content of zinc has a close effect on the magnetic properties of BaZnzCo2-zFe16O27/SiO2 microcrystalline glass ceramics, the greater the zinc content, the higher the values of imaginary part of permeability and magnetic loss.

Preparation and Microwave Absorbing Properties of Double-layer Fine Iron Tailings Cementitious Materials

To develop the microwave absorbing(MA)properties of cementitious material mixed with mine solid waste,the iron tailings cementitious microwave absorbing materials were prepared.The iron tailings was treated into different particle sizes by planetary ball mill,and the physicochemical properties of iron tailings were tested by laser particle size analyzer and scanning electron microscope(SEM).The electromagnetic parameters of iron tailings cementitious materials were characterized by a vector network analyzer and simulated MA properties,and the MA properties of iron tailings-cement composite system with steel fiber as absorber was studied.Based on the design of the single-layer structure,optimum mix ratio and thickness configuration method of double-layer structure were further studied,meanwhile,the mechanical properties and engineering application were analyzed and discussed.The results show that the particle size of iron tailings can afiect its electromagnetic behavior in cementitious materials,and the smaller particles lead the increase of demagnetisation efiect induced by domain wall motion and achieve better microwave absorbing properties in cementitious materials.When the thickness of matching layer and absorbing layer is 5 mm,the optimized microwave absorbing properties of C1/C3 double-layer cementitious material can obtain optimal RL value of-27.61 dB and efiective absorbing bandwidth of 0.97 GHz,which attributes to the synergistic efiect of impedance matching and attenuation characteristics.The double-layer microwave absorbing materials obtain excellent absorbing properties and show great design flexibility and diversity,which can be used as a suitable candidate for the preparation of favorable microwave absorbing cementitious materials.

Electromagnetic and microwave absorbing properties of FeCoB powder composites

The electromagnetic and microwave absorbing properties of FeCoB powder composites prepared by sin- gle-roller melt-spinning and mechanical milling processes were investigated in this paper. The result indicates that the flake-like powders are obtained. As milling time increases, the flake-like powder particles tend to agglomerate, causing the flake-like powders decrease gradually. The milling time plays an important role in the electromagnetic parameters which relates to the shape and size of the powder particles. The calculation shows that the sample milled for 6 h could achieve an optimal reflection loss of -11.5 dB at 5.8 GHz, with mass fraction of 83 % and a matching thickness of 1.8 mm. The result also indicates that the microwave absorbing properties of the FeCoB powder composites are adjustable by changing their thickness, and can be applied as a thinner microwave absorbing material in the range of 2-8 GHz.

Microstructure and microwave electromagnetic properties of Dy^(3+)-doped W-type hexaferrites

Ba 1 x Dy x Co 2 Fe 16 O 27 （x = 0.00, 0.05, 0.10, 0.15, and 0.20） was prepared by the solid-state method. The phase structure was studied using powder X-ray diffraction （XRD）, the electromagnetic properties were measured, and the reflection loss of Dy 3＋ -doped ferrite material was calculated using electromagnetic parameters by the transmission line theory. All XRD patterns showed the single phase of the magnetoplumbite barium ferrite without other intermediate phase when x ≤ 0.15. The values of ε ′ and ε ″ increased slightly with Dy 3＋ ions doping. The values of μ″ and μ′ were improved with Dy 3＋ doping, exhibiting excellent microwave magnetic performance. The reasons have also been discussed using the electromagnetic theory. Dy substitution could increase microwave-absorbing performance and broaden frequency band （reflection loss （RL） -10 dB）, and the absorbing peak shifted to high-frequency position. When x = 0.2, ferrite layer exhibited the most excellent microwave-absorbing performance at a thin matching thickness of 1.5 mm. The peak value of RL was around -15 dB, and the frequency band （RL -10 dB） was about 7 GHz （from 8 to 15 GHz）.

Crystal microstructure, infrared absorption, and microwave electromagnetic properties of (La_(1-x)Dy_x)_(2/3)Sr_(1/3)MnO_3

The manganite perovskite polycrystal samples of （La1-xDyx）2/3Sr1/3MnO3 （x = 0, 0.1, 0.2, 0.35, and 0.5） doped with Dy were prepared by solid state reaction in atmosphere to measure their X-ray diffraction （XRD） patterns, scanning electric microscope （SEM） images, infrared absorption spectra, and microwave electromagnetic properties. The displacement of the XRD peaks of the samples was found, and the 2θ increases from 0.05o to 0.5o. The grains of undoped La2/3Sr1/3MnO3 not only have the greatest size, but also the most regular shape. The size of the grains decreases as the Dy doping content increases from 0 to 0.5. The infrared absorption spectra of all samples were measured at room temperature. An absorption peak corresponding to the stretching vibration mode of Mn-O bonds appears within the range of 591-629 cm-1. The absorption peak shifts from a higher frequency to a lower one with the decrease of the average ionic radius of A-site. The frequency de- pendence of microwave-absorbing properties, imaginary components of the complex magnetic permeability μ＂ and dielectric permeability ε＂ for all samples was measured at room temperature from 8 to 13 GHz. The results show that the loss of microwave absorption can be attrib- uted to both the magnetic and electric losses. The increase of Dy content not only enhances the microwave absorption but also causes the displacement of the absorption peaks.

Microstructure and microwave dielectric properties of ZnO-B_2O_3 added (Ca_(0.254)Li_(0.19)Sm_(0.14))TiO_3 ceramics

The effects of ZnO-B2O3 （ZB2） on the sintering behavior and microwave dielectric properties of （Ca0.254Li0.19Sm0.14）TiO3 ceramics were investigated. The densities of the specimens reached the maximum value by adding 3 wt.% ZB2 and then decreased. The sintering temperature of the specimens was lowered from 1300 to 1100℃ without degradation of the microwave dielectric properties. The （Ca0.254Li0.19Sm0.14）TiO3＋ 3 wt.% ZB2 sintered at 1100℃ for 3 h showed good microwave dielectric properties, εr= 108.2, Qf= 6545 GHz, and rf= 6.5 ppm/℃, respectively, indicating that ZB2 was an effective sintering aid to improve the densification and microwave dielectric properties of （Ca0.254Li0.19Sm0.14）TiO3 ceramics.

Effect of Rare Earth Element on Microwave Absorption Properties of Nano-Lithium Ferrite

Superfine powders of nano-lithium ferrite doped with different kinds and amount of rare earth element were prepared by sol-gel method. Their photograph was taken by transmission electron microscopy. From it, we can see most of particles are less than 100 nm and average diameter of superfine powders is 50 nm. Then their microwave absorption properties are measured by power ratio method. The result indicates that microwave absorption properties of nano-lithium ferrite doped with rare earth element change obviously. Different kinds and amount of rare earth element make different influences. Magnetic hysteresis loop is surveyed by vibrating sample magnetometer. We find that there are some relationships between magnetism and microwave absorption properties.

Mossbauer spectroscopy studies on the particle size distribution effect of Fe–B–P amorphous alloy on the microwave absorption properties

An Fe-based nanocrystalline alloy powder is important for application in microwave absorption,and the particle size has a critical impact on the electromagnetic microwave parameters.Therefore,it is necessary to study further the effects of the particle size on such parameters and improve the microwave absorption performance of Febased nanocrystalline powers.In this study,Fe-B-P particles were prepared through a synthetic approach consisting of an aqueous chemical reduction and a ball milling treatment.We investigated the effects of ball milling on the microstructure and electromagnetic properties of Fe-B-P particles.The experimental results indicate that the Fe-B-P particles synthesized through an aqueous chemical reduction are amorphous spheres.Fe-B-P particles with an original particle size of 200-1200 nm can be milled into an irregular shape with the size reduced to\500 nm after 0.5 h of ball milling,and subsequently,the particles become smaller with increases in the milling time,with traces of Fe2O3 generated on the particle surface.The results of the Mo¨ssbauer spectra show that a portion of the small particles demonstrate a superparamagnetic property.The volume proportions of the superparamagnetic component increase from 13.1 to 15.8%as the treatment time increases.We measured the permittivity and permeability spectra of Fe-B-P particles within the frequency range of 2-18 GHz.The reflection loss(RL)is-10 dB for an absorber thickness of 1.7-5.0 mm.The RL is-20 dB for an absorber thickness of 1.9-2.7 mm.The microwave absorption properties of samples with the same thickness are improved with an increase in the treatment time and are shifted to a higher frequency,which will broaden the bandwidth of the absorption as well.

Influence of CaxSr1-x(0≤x≤1)Substitution for Zn on Microwave Dielectric Properties of Li2ZnTi3O8 Ceramic as Temperature Stable Materials

A temperature stable Li2Zn0.95(SrxCa1-x)0.05Ti3O8(0≤x≤1)ceramics were fabricated using a conventional solid-state route sintered at 1100℃for 4 h.The XRD results indicate that the main phase Li2ZnTi3O8 and secondary phase including SrxCa1-xTiO3(0≤x≤1)solid solution and TiO2 co-exist in composite and form a stable composite system when the(CaxSr1-x)(0≤x≤1)substitutes for Zn of Li2ZnTi3O8 ceramic.As x is increased from 0 to 1,the relative permittivity(εr)increases from 26.65 to 27.12,and the quality factor(Q×f)increases from 63300 to 66600 GHz.With the increased of x,the temperature coefficient of resonant frequency(τf)increases from 0.27 to 8.23 ppm/℃,and then decreases to 3.51 ppm/℃.On the whole,the Li2Zn0.95(SrxCa1-x)0.05Ti3O8(0≤x≤1)ceramics show excellent comprehensive properties of middleεr=25-27,higher Q×f≥60000 GHz andτf≤±8.5 ppm/℃.

Microwave Absorption Properties of Polyester Composites Incorporated with Heterostructure Nanofillers with Carbon Nanotubes as Carriers

Carbonaceous nanomaterials such as carbon nanotubes （CNTs）, magnetic metal nanomaterials and semicon- ductor nanomaterials are superior candidates for microwave absorbers. Taking full advantage of the features of CNTs, nanophase cobalt and nanophase zinc oxide, whose main microwave absorption mechanisms are based on resistance loss, magnetic loss and dielectric loss, we fabricate CNT/Co and CNT/ZnO heterostructure nanocom- posites, respectively. By using the CNTs, CNT/Co nanocomposites and CNT/ZnO nanocomposites as nanofillers, composites with polyester as matrix are prepared by in situ polymerization, and their microwave absorption per- formance is studied. It is indicated that the synergetic effects of the physic properties of different components in nano-heterostructures result in greatly enhanced microwave absorption performance in a wide frequency range. The absorption peak is increased, the absorption bandwidth is broadened, and the maximum peak shifts to a lower frequency.

Dielectric Properties and Microwave Heating of Molybdenite Concentrate at 2.45 GHz Frequency

Dielectric properties were measured using cavity perturbation method. The temperature rising behaviors of molybdenite concentrate were investigated in the field of microwave. This process was conducted to show the microwave absorption properties of molybdenite concentrate and the feasibility of microwave roasting molybdenite concentrate to prepare high purity MOO3. The dielectric constant,dielectric loss,and loss tangent increase from 3. 51 to 5. 04,0. 22 to 0. 51 and 0. 065 to 0. 102 respectively. They are proportional to the apparent density of molybdenite concentrate in the range of 0. 9-1. 4 g/cm3. The results show that the molybdenite concentrate has good microwave absorption capacity in the conventional density range. The temperature rising curves show that the apparent heating rate of the molybdenite concentrate increases with the increase in microwave power and decreases with the increase in the sample mass and thickness. The temperature of concentrate sample of 100 g reaches approximately 800 ℃ after 5 min of microwave treatment at 0. 5 kW of power. Our findings show that it is feasible to prepare high-purity MOO3from molybdenite concentrate by microwave roasting.

Microstructures and Microwave Dielectric Properties of La-Substituted Ba(Mg_1/3Nb_(2/3))O_3 Ceramics

La substituted Ba(Mg_ 1/3Nb_ 2/3)O_3 ceramics was expected to enhance the 1∶2 ordering degree of B-site ions due to the existence of vacancies that promote cation movement and result in improvement of the Q_f value. The relation between the microstructure and microwave dielectric properties of Ba_ 1-xLa_ 2x/3(Mg_ 1/3Nb_ 2/3)O_3 ceramics was investigated. La substituted Ba(Mg_ 1/3Nb_ 2/3)O_3 ceramics can improve the sinterability of specimens. Both 1:2 ordering degree and grain size increase as A-site vacancies increase. This can be explained by the existence of vacancies that promote cation movement. The Q_f value increase with small La content, then decrease rapidly. The highest Q_f value achieved in this investigation is about 55000 GHz for Ba_ 0.995La_ 0.01/3(Mg_ 1/3Nb_ 2/3)O_3. The improvement of Q_f value with A-site vacancies is related to the increase of the degree of B-site ordering and grain size of the specimen.

Structure and Dielectric Properties of ZnO and Nb_2O_5 Doped BaO-TiO_2 System Microwave Ceramics

The microwave dielectric properties and microstructure of BaTi4.3ZnyO9.6＋y ＋0.02 mol% SnO2＋0.01 mol% MnCO3＋x mol% Nb2O5（x=0-0.05, y=0-0.08） system ceramics were studied as a function of the amount of ZnO and Nb2O5 doped. Addition of （y=0-0.05） ZnO and （x=0-0.025） Nb2O5 enhanced the reactivity and decreased the sintering temperature effectively. It also increased the dielectric constant ε r and quality factor Q（=1/tan 8） of the system due to the substitution of Ti^4＋ ions with incorporating Zn^2＋and Nb^5＋ ions, which was analyzed by the reaction ZnO＋Nb2O5＋ 3 TiTxTi →ZnTi＋ 2NbTi＋3TiO2. When the system doped with （y=0.05） ZnO and （x=0.025） Nb205 were sintered at 1 160 ℃ for 6 h, the εr. Qf0 value and rfwere 36.5, 42 000 GHz, and＋1.8 ppm/℃, respectively, at 5 GHz.

Enhanced thermal conductivity and microwave dielectric properties by mesostructural design of multiphase nanocomposite

Next-generation packaging materials are expected to have higher thermal conductivity,because the heat accumulated in high-performance electronic equipment should be removed to increase the service life of the equipment.At the same time,the dielectric loss of the material needs to be reduced to lessen signal delay and attenuation,especially for the applications under high frequency.In this work,we introduce nano-silicon carbide(SiC)and carbon nanotubes(CNTs)into the polystyrene(PS)and poly(methyl methacrylate)(PMMA)blends system.The design of two-way migration at the interface of CNTs and SiC nanoparticles is realized through the masterbatch method and processing technology control.As a result,the thermal conductivity is successfully increased up to 75%.Meanwhile,compared to the CNTs single-phase migration system,it effectively reduces the dielectric loss of the nanocomposite and optimizes the electrical insulation.This work has significant practical application value in the design of electronic device substrates and packaging materials,and provides an innovative methodology for the mesostructure design of multiphase nanocomposites.

Effect of La ^(3+) on Microwave Dielectric Properties of (Pb_ (0.45)Ca_ (0.55))(Fe_(0.50Nb_ (0.5))O_3 Ceramics

In this work, microwave dielectric properties of A-site substitution by La 3+ in (Pb_ 0.45Ca_ 0.55)(Fe_ 0.5Nb_ 0.5)O_3 system were investigated. Microwave dielectric properties of A-site charge unbalance substitution of [(Pb_ 0.45Ca_ 0.55)_ 1-xLa_x](Fe_ 0.5Nb_ 0.5)O 3+ (P45CLFN) were improved because the solid solution of small amount of surplus La 3+ with (Pb,Ca) 2+ could eliminate oxygen vacancies, and the formation of secondary phase(pyrochlore) was also caused by surplus La 3+. The decreasing of dielectric constant with the increase of La 3+ content is due to the formation of pyrochlore. The grain size is changed slightly and Q_f values(7000～7300 GHz) are almost unchanged at x=0.02～0.10, but the temperature coefficient of resonant frequency (TCF) are increased and changed from negative to positive. TCF is zero at x=0075 with Q_f=7267 GHz and K=89. TCF of all specimens are within ±5×10 -6 ℃ -1.

Low-Temperature Sintering and Microwave DielectricProperties of Ba_2Ti_3Nb_4O_(18) Ceramics

The effects of CuO and H3BO3 additions on the low-temperature sintering,microstructure,and microwave dielectric properties of Ba2Ti3Nb4O18 ceramics were investigated.The addition of less amount of CuO （ 〈1 wt%） considerably facilitated the densification of Ba2Ti3Nb4O18 ceramics.Appropriate addition of H3BO3 （ 〈3.5 wt%） remarkably improved the microwave dielectric properties of ceramics.The addition of H3BO3 and CuO successfully reduced the sintering temperature of Ba2Ti3Nb4O18 ceramics from 1300 to 1050 ℃.Ba2Ti3Nb4O18 ceramics sintered at 1 050 ℃ for 4 h with the addition of 1.0 wt% CuO and 3.5 wt% H3BO3 exhibited good microwave dielectric properties：er=33.74,Q？f=13 812 GHz,and tf=-5.35 ppm/°C at about 5.0 GHz.

Effects of La^(3+) on microwave dielectric properties of(Pb_(0.5)Ca_(0.5))(Fe-(0.5)Ta_(0.5))O_3 ceramics

This work investigated the microwave dielectric properties of A-site substitution by rare earth La3＋in（Pb0.5Ca0.5）（Fe0.5Ta0.5）O3（PCFT） system.A single perovskite phase was obtained only when the doping content was 2%.Suitable La3＋ doping improved microwave dielectric performances.Excessive La3＋doping caused the formation of secondary phase,which resulted in the decreasing of permittivity εrand quality factor Qfvalues.Especially,when the doping content is 2%-5%,permittivity εrwas above 75 and Qfvalues were 6 902-7 416 GHz.