Experimental investigation on vibration characteristics of the medium-low-speed maglev vehicle-turnout coupled system

The steel turnout is one of the key components in the medium–low-speed maglev line system.However,the vehicle under active control is prone to vehicle–turnout coupled vibration,and thus,it is necessary to identify the vibration characteristics of this coupled system through field tests.To this end,dynamic performance tests were conducted on a vehicle–turnout coupled system in a medium–low-speed maglev test line.Firstly,the dynamic response data of the coupled system under various operating conditions were obtained.Then,the natural vibration characteristics of the turnout were analysed using the free attenuation method and the finite element method,indicating a good agreement between the simulation results and the measured results;the acceleration response characteristics of the coupled system were analysed in detail,and the ride quality of the vehicle was assessed by Sperling index.Finally,the frequency distribution characteristics of the coupled system were discussed.All these test results could provide references for model validation and optimized design of medium–low-speed maglev transport systems.

Effect of low-speed waterjet pressure on the rock-breaking performance of unsubmerged cavitating abrasive waterjet

Unsubmerged cavitating abrasive waterjet(UCAWJ)has been shown to artificially create a submerged environment that produces shear cavitation,which effectively enhances rock-breaking performance.The shear cavitation generation and collapse intensity depend on the pressure difference between the intermediate high-speed abrasive waterjet and the coaxial low-speed waterjet.However,the effect of the pressure of the coaxial low-speed waterjet is pending.For this purpose,the effect of low-speed waterjet pressure on rock-breaking performance at different standoff distances was experimentally investigated,and the effects of erosion time and ruby nozzle diameter on erosion performance were discussed.Finally,the micromorphology of the sandstone was observed at different locations.The results show that increased erosion time and ruby nozzle diameter can significantly improve the rock-breaking performance.At different standoff distances,the mass loss increases first and then decreases with the increase of low-speed waterjet pressure,the maximum mass loss is 10.4 g at a low-speed waterjet pressure of0.09 MPa.The surface morphology of cavitation erosion was measured using a 3D profiler,the increase in both erosion depth and surface roughness indicated a significant increase in the intensity of the shear cavitation collapse.At a low-speed waterjet pressure of 0.18 MPa,the cavitation erosion surface depth can reach 600μm with a roughness of 127μm.

Physical modeling of long-term dynamic characteristics of the subgrade for medium-low-speed maglevs

To investigate the dynamic characteristics and long-term dynamic stability of the new subgrade structure of medium-low-speed(MLS)maglevs,cyclic vibration tests were performed under natural and rainfall conditions,and the dynamic response of the subgrade structure was monitored.The dynamic response attenuation characteristics along the depth direction of the subgrade were compared,and the distribution characteristics of the dynamic stress on the surface of the subgrade along the longitudinal direction of the line were analyzed.The critical dynamic stress and cumulative deformation were used as indicators to evaluate the long-term dynamic stability of the subgrade.Results show that water has a certain effect on the dynamic characteristics of the subgrade,and the dynamic stress and acceleration increase with the water content.With the dowel steel structure set between the rail-bearing beams,stress concentration at the end of the loaded beam can be prevented,and the diffusion distance of the dynamic stress along the longitudinal direction increases.The dynamic stress measured in the subgrade bed range is less than 1/5 of the critical dynamic stress.The postconstruction settlement of the subgrade after similarity ratio conversion is 3.94 mm and 7.72 mm under natural and rainfall conditions,respectively,and both values are less than the 30 mm limit,indicating that the MLS maglev subgrade structure has good long-term dynamic stability.

SOME CHARACTERISTICS OF LOW-SPEED STREAKS UNDER SHEARED AIR-WATER INTERFACES

The characteristics of low-speed fluid streaks occurring under sheared air-water interfaces were examined by means of hydrogen bubble visualization technique. A critical shear condition under which the streaky structure first appears was determined to be u(tau) approximate to 0.19 cm/s. The mean spanwise streak spacing increases with distance from the water surface owing to merging and bursting processes, and a linear relationship describing variation of non-dimensional spacing <(<lambda>+)over bar> versus y(+) was found essentially independent of shear stress on the interface. Values of <(<lambda>+)over bar>, however, are remarkably smaller than their counterparts in the near-wall region of turbulent boundary layers. Though low-speed streaks occur randomly in time and space, the streak spacing exhibits a lognormal probability distribution behavior. A tentative explanation concerning the formation of streaky structure is suggested, and the fact that <(<lambda>+)over bar> takes rather smaller values than that in wall turbulence is briefly discussed.

POD analysis of the instability mode of a low-speed streak in a laminar boundary layer

The instability of one single low-speed streak in a zero-pressure-gradient laminar boundary layer is investigated experimentally via both hydrogen bubble visualization and planar particle image velocimetry(PIV) measurement. A single low-speed streak is generated and destabilized by the wake of an interference wire positioned normal to the wall and in the upstream. The downstream development of the streak includes secondary instability and self-reproduction process, which leads to the generation of two additional streaks appearing on either side of the primary one. A proper orthogonal decomposition(POD) analysis of PIV measured velocity field is used to identify the components of the streak instability in the POD mode space: for a sinuous/varicose type of POD mode, its basis functions present anti-symmetric/symmetric distributions about the streak centerline in the streamwise component, and the symmetry condition reverses in the spanwise component. It is further shown that sinuous mode dominates the turbulent kinematic energy(TKE) through the whole streak evolution process, the TKE content first increases along the streamwise direction to a saturation value and then decays slowly. In contrast, varicose mode exhibits a sustained growth of the TKE content,suggesting an increasing competition of varicose instability against sinuous instability.

High-frequency characterization of high-speed modulators and photodetectors in a link with low-speed photonic sampling

We propose a low-speed photonic sampling for independent high-frequency characterization of a Mach–Zehnder modulator(MZM)and a photodetector(PD)in an optical link.A low-speed mode-locked laser diode(MLLD)provides an ultrawideband optical stimulus with scalable frequency range,working as the photonic sampling source of the link.The uneven spectrum lines of the MLLD are firstly characterized with symmetric modulation within the interesting frequency range.Then,the electro-optic modulated signals are down-converted to the first Nyquist frequency range,yielding the self-referenced extraction of modulation depth and half-wave voltage of the MZM without correcting the responsivity fluctuation of the PD in the link.Finally,the frequency responsivity of the PD is self-referenced measured under null modulation of the MZM.As frequency responses of the MZM and the PD can be independently obtained,our method allows self-referenced high-frequency measurement for a high-speed optical link.In the proof-of-concept experiment,a 96.9 MS/s MLLD is used for measuring a MZM and a PD within the frequency range up to 50 GHz.The consistency between our method and the conventional method verifies that the ultra-wideband and self-referenced high-frequency characterization of high-speed MZMs and PDs.

Numerical study on evolution of subharmonic varicose low-speed streaks in turbulent channel flow

The evolution of two spanwise-aligned low-speed streaks in a wall turbulent flow, triggered by the instability of the subharmonic varicose （SV） mode, is studied by a direct numerical simulation （DNS） method in a small spatial-periodic channel. The results show that the SV low-speed streaks are self-sustained at the early stage, and then transform into subharmonic sinuous （SS） low-speed streaks. Initially, the streamwise vortex sheets are formed by shearing, and then evolve into zigzag vortex sheets due to the mutual induction. As the intensification of the SV low-speed streaks becomes prominent, the tilted streamwise vortex tubes and the V-like streamwise vortex tubes can be formed simultaneously by increasing ＋~. When the SV low-speed streaks break down, new zigzag streamwise vortices will be generated, thus giving birth to the next sustaining cycle of the SV low-speed streaks. When the second breakdown happens, new secondary V-like streamwise vortices instead of zigzag streamwise vortices will be generated. Because of the sweep motion of the fluid induced by the secondary V-like streamwise vortices, each decayed low-speed streak can be divided into two parts, and each part combines with the part of another streak, finally leading to the formation of SS low-speed streaks.

Optimizing the Exhaust System of Marine Diesel Engines to Improve Low-speed Performances and Cylinder Working Conditions

Proper design of exhaust systems in marine high-power turbocharged diesel engines can contribute to improve the low-speed performance of these engines and make the working conditions of the cylinders more uniform.Here a high-power marine 16-cylinder V-type turbocharged diesel engine is simulated using the GT-Power software.The results reveal the differences induced by different exhaust system structures,such as an 8-cylinder-inpipe exhaust system with single/double superchargers and a 4-cylinder-in-pipe exhaust system with a single supercharger.After a comparative analysis,the 8-cylinder type with double superchargers is determined to be the optimal solution,and the structure of the exhaust system is further optimized.The simulations show that the optimized maximum exhaust temperature difference among cylinders is reduced by 66%.Finally,the simulation results and the optimized performance of the designed exhaust system are verified through experiments.

Numerical simulation on evolution of subharmonic low-speed streaks in minimal channel turbulent flow

The evolution of low-speed streaks in the turbulent boundary layer of the minimum channel flow unit at a low Reynolds number is simulated by the direct numer- ical simulation （DNS） based on the standard Fourier-Chebyshev spectral method. The subharmonic sinuous （SS） mode for two spanwise-aligned low-speed streaks is excited by imposing the initial perturbations. The possibilities and the physical realities of the turbulent sustaining in the minimal channel unit are examined. Based on such a flow field environment, the evolution of the low-speed streaks during a cycle of turbulent sus- taining, including lift-up, oscillation, and breakdown, is investigated. The development of streamwise vortices and the dynamics of vortex structures are examined. The results show that the vortices generated from the same streak are staggered along the streamwise direction, while the vortices induced by different streaks tilt toward the normal direction due to the mutual induction effect. It is the spatial variations of the streamwise vortices that cause the lift-up of the streaks. By resolving the transport dynamics of enstrophy, the strength of the vortices is found to continuously grow in the logarithmic layer through the vortex stretching mechanism during the evolution of streaks. The enhancement of the vortices contributes to the spanwise oscillation and the following breakdown of the low-speed streaks.

Dynamics of low-speed streak evolution and interaction in laminar boundary layer

The present paper presents an experimental effort on the regeneration process of two low-speed laminar streaks in a zero-pressure-gradient laminar boundary layer. Two vertical thin wires separated by a spanwise distance of 30 mm are used to introduce disturbances of two rolls of transitional Karmain vortex street to the downstream boundary layer. Both hydrogen bubble visualization and particle image velocimetry （PIV） measurement show that two lowspeed streaks are induced through leading-edge receptivity process. As these streaks develop in the downstream, two additional low-speed streaks begin to appear outboard of the flank of the original two, together with complex dynamics of streak splitting and merging. A flow pattern of four streaks aligned along the spanwise direction occurs finally in the far downstream. It is found that besides the mechanisms of streak breakdown, the streak interaction is also an important factor characterizing the instability of low speed streaks and their regeneration process.

Aerodynamic Features of High-Speed Maglev Trains with Different Marshaling Lengths Running on a Viaduct under Crosswinds

The safety and stability of high-speed maglev trains traveling on viaducts in crosswinds critically depend on their aerodynamic characteristics.Therefore,this paper uses an improved delayed detached eddy simulation(IDDES)method to investigate the aerodynamic features of high-speed maglev trains with different marshaling lengths under crosswinds.The effects of marshaling lengths(varying from 3-car to 8-car groups)on the train’s aerodynamic performance,surface pressure,and the flow field surrounding the train were investigated using the three-dimensional unsteady compressible Navier-Stokes(N-S)equations.The results showed that the marshaling lengths had minimal influence on the aerodynamic performance of the head and middle cars.Conversely,the marshaling lengths are negatively correlated with the time-average side force coefficient(CS)and time-average lift force coefficient(Cl)of the tail car.Compared to the tail car of the 3-car groups,the CS and Cl fell by 27.77%and 18.29%,respectively,for the tail car of the 8-car groups.It is essential to pay more attention to the operational safety of the head car,as it exhibits the highest time average CS.Additionally,the mean pressure difference between the two sides of the tail car body increased with the marshaling lengths,and the side force direction on the tail car was opposite to that of the head and middle cars.Furthermore,the turbulent kinetic energy of the wake structure on the windward side quickly decreased as marshaling lengths increased.

Research on Feature Extraction Method for Low-Speed Reciprocating Bearings Based on Segmented Short Signal Modulation Signal Bispectrum Slicing

Bearing condition monitoring and fault diagnosis (CMFD) can investigate bearing faults in the early stages, preventing the subsequent impacts of machine bearing failures effectively. CMFD for low-speed, non-continuous operation bearings, such as yaw bearings and pitch bearings in wind turbines, and rotating support bearings in space launch towers, presents more challenges compared to continuous rolling bearings. Firstly, these bearings have very slow speeds, resulting in weak collected fault signals that are heavily masked by severe noise interference. Secondly, their limited rotational angles during operation lead to a restricted number of fault signals. Lastly, the interference from deceleration and direction-changing impact signals significantly affects fault impact signals. To address these challenges, this paper proposes a method for extracting fault features in low-speed reciprocating bearings based on short signal segmentation and modulation signal bispectrum (MSB) slicing. This method initially separates short signals corresponding to individual cycles from the vibration signals based on encoder signals. Subsequently, MSB analysis is performed on each short signal to generate MSB carrier-slice spectra. The optimal carrier frequency and its corresponding modulation signal slice spectrum are determined based on the carrier-slice spectra. Finally, the MSB modulation signal slice spectra of the short signal set are averaged to obtain the overall average feature of the sliced spectra.

A novel refined dynamic model of high-speed maglev train-bridge coupled system for random vibration and running safety assessment

Running safety assessment and tracking irregularity parametric sensitivity analysis of high-speed maglev train-bridge system are of great concern,especially need perfect refinement models in which all properties can be well characterized based on various stochastic excitations.A three-dimensional refined spatial random vibration analysis model of high-speed maglev train-bridge coupled system is established in this paper,in which multi-source uncertainty excitation can be considered simultaneously,and the probability density evolution method(PDEM)is adopted to reveal the system-specific uncertainty dynamic characteristic.The motion equation of the maglev vehicle model is composed of multi-rigid bodies with a total 210-degrees of freedom for each vehicle,and a refined electromagnetic force-air gap model is used to account for the interaction and coupling effect between the moving train and track beam bridges,which are directly established by using finite element method.The model is proven to be applicable by comparing with Monte Carlo simulation.By applying the proposed stochastic framework to the high maglev line,the random dynamic responses of maglev vehicles running on the bridges are studied for running safety and stability assessment.Moreover,the effects of track irregularity wavelength range under different amplitude and running speeds on the coupled system are investigated.The results show that the augmentation of train speed will move backward the sensitive wavelength interval,and track irregularity amplitude influences the response remarkably in the sensitive interval.

Disturbance rejection tube model predictive levitation control of maglev trains

Magnetic levitation control technology plays a significant role in maglev trains.Designing a controller for the levitation system is challenging due to the strong nonlinearity,open-loop instability,and the need for fast response and security.In this paper,we propose a Disturbance-Observe-based Tube Model Predictive Levitation Control(DO-TMPLC)scheme combined with a feedback linearization strategy for the levitation system.The proposed strategy incorporates state constraints and control input constraints,i.e.,the air gap,the vertical velocity,and the current applied to the coil.A feedback linearization strategy is used to cancel the nonlinearity of the tracking error system.Then,a disturbance observer is implemented to actively compensate for disturbances while a TMPLC controller is employed to alleviate the remaining disturbances.Furthermore,we analyze the recursive feasibility and input-to-state stability of the closed-loop system.The simulation results indicate the efficacy of the proposed control strategy.

Study on Dynamic Characteristics of Superconducting Electrodynamic Maglev Train

This study considers a superconducting electrodynamic maglev train of MLX01 type.The characteristics of the electromagnetic spring coefficient of a single bogie under different magnetomotive force(MF) of the superconducting coil and standard air gap(Sag) were explored.In view of the small electromagnetic damping,a passive damping control strategy and an active damping control strategy were designed to increase the electromagnetic damping force between the superconducting coil and ground coil.Combined with the coupling numerical model of a single bogie,the vibration characteristics of the bogie in different directions with different damping control strategies were studied when the Sag and MF were fixed.The results can provide important theoretical support for stable operation control of maglev trains.

列车荷载作用下的磁浮轨道梁响应极值条件

为研究磁浮轨道梁动力响应的变化规律,将磁浮列车简化为移动的均布荷载,采用解析法得到简支轨道梁动力响应的解析解,并讨论轨道梁最大值随车速、跨度等参数的变化规律,推导磁浮轨道梁动力响应的极值条件,利用有限元方法和车-桥耦合振动方法进行验证.结果表明:列车与轨道梁跨度比值较大时,随列车速度的增加轨道梁跨中最大响应以波动形式增加,最大响应存在极值,轨道梁响应随轨道梁跨度、质量等参数也有类似规律;当车速和跨度的乘积为特定常数,或轨道梁一阶竖弯频率与跨度的乘积为车速特定倍数时,轨道梁产生消振现象.

Vibration analysis of maglev three-span rigid frame bridge considering magnetic force

The dynamic interaction between the maglev vehicle and the three-span rigid frame bridge is discussed. With the consideration of magnetic force, the interaction model is developed. Numerical simulations are performed to study the dynamic characteristics of the bridge during vehicle movement along the bridge. The results show that a reasonable value of the linear stiffness ratio of columns to beams is between 2. 0 and 3.0. The dynamic responses of the bridge are aggravated with the decrease in bending rigidity and the increase in vehicle speed and the span ratio of the bridge. It is suggested that a definite way is to control impact coefficients and acceleration in the dynamic design of the bridge. It is unsuitable to adopt the moving load model and the moving mass model in the design. The proposed results can serve in the design of high-speed maglev three-span rigid frame bridges.

磁浮飞行风洞动模型系统振动特性仿真研究

磁浮飞行风洞是一种将真空管道高速磁浮技术与动模型试验原理相结合的新概念空气动力试验设施。试验模型在试验过程中由于受到气动载荷、惯性载荷和轨道不平顺的联合作用,会发生系统振动和姿态改变。利用动力学软件建立动模型系统的多体刚柔耦合动力学模型,通过仿真计算了系统模态演变及动力学响应情况。结果表明:动模型在起飞时刻会发生剧烈振动和姿态改变;当运行速度为0.4马赫数时,轨道不平顺激扰频率会与动模型系统固有频率耦合引起系统共振,导致悬浮高度发生较大幅度的谐波振荡,共振频率为7.4 Hz,振荡幅度为8.9 mm;动模型俯仰姿态角随试验马赫数的增大而增大,当试验马赫数为0.5时,试验模型最大俯仰角约为2.25°。研究结果对于磁浮飞行风洞相关系统的设计与发展动模型试验技术具有参考意义。

短定子磁浮列车基于悬浮间隙实现测速和定位的算法仿真及应用

短定子磁浮列车测速和定位技术实现方式与传统轮轨不同,目前有多种技术实现方式,但都需要在磁浮列车上设置测速和定位设备或系统,且与悬浮控制系统相互独立,但悬浮控制系统对速度信号和位置信号又有一定的依赖性。因此,设计了一种基于悬浮间隙实现测速和定位的算法,并通过仿真达到算法设计预期目的,最后通过编程将算法嵌入磁浮列车的悬浮控制系统硬件平台,实现测速和定位的算法应用,测速和定位信号完全集成于悬浮控制系统中,摆脱悬浮控制系统对外置测速定位系统的依赖,提升磁浮列车在轨道交通市场的竞争力。

中低速磁浮信号系统与其他专业接口分析

针对中低速磁浮轨道交通建设过程中,信号系统与磁浮交通特殊的轨道、道岔、车辆等系统接口出现的问题进行分析。提出信号系统与其他专业的接口要求,并对部分问题提出解决方案,使磁浮交通信号系统与其他专业接口间出现的问题得到解决,为其他中低速磁浮项目建设提供参考。