Broadband third-order optical nonlinearities of layered franckeite towards mid-infrared regime

The study of nonlinear optical responses in the mid-infrared(mid-IR)regime is essential for advancing ultrafast mid-IR laser applications.However,nonlinear optical effects under mid-IR excitation are rarely reported due to the lack of suitable nonlinear optical materials.The natural van derWaals heterostructure franckeite,known for its narrow bandgap and stability in air,shows great potential for developing mid-IR nonlinear optical devices.We have experimentally demonstrated that layered franckeite exhibits a broadband wavelength-dependent nonlinear optical response in the mid-IR spectral region.Franckeite nanosheets were prepared using a liquid-phase exfoliation method,and their nonlinear optical response was characterized in the spectral range of 3000 nm to 5000 nm.The franckeite nanosheets exhibit broadband wavelengthdependent third-order nonlinearities,with nonlinear absorption and refraction coefficients estimated to be about 10^(-7)cm/W and 10^(-11)cm^(2)/W,respectively.Additionally,a passively Q-switched fluoride fiber laser operating around a wavelength of 2800 nm was achieved,delivering nanosecond pulses with a signal-to-noise ratio of 43.6 dB,based on the nonlinear response of franckeite.These findings indicate that layered franckeite possesses broadband nonlinear optical characteristics in the mid-IR region,potentially enabling new possibilities for mid-IR photonic devices.

Rapidly determining kinematic viscosity of aviation lubricating oil 50-1-4Φ by mid-infrared spectrometry

This paper analyzed 11 lubricating oil 50-1-4Ф samples of different base oil content （standard oil） and 28 used oil samples by Fourier transform mid-infrared spectrometer （FTIR）. First, the absorption peak of 1 465 cm 1 was selected as the characteristic peak for determining their kinematic viscosities. And then correlation of the kinematic viscosity and the absorbance at characteristic peaks of corresponding infrared spectrum of standard oil and used oil samples was analyzed, re- spectively, and two regression equations were proposed. Finally, the regression equation of standard oil was corrected through other 20 new oil samples. The results show that determining kinematic viscosity of new lubricating oil 50-1-4Ф and the used one by FTIR is feasible and reliable.

Rapidly determining fuel pollution level of aviation lubricating oil 50-1-4Φby mid-infrared spectrometry

A series of aviation lubrication oil 50-1-4φ samples were prepared with different RP-3 content, and then these sam- ples were analyzed by Fourier transform mid-infrared spectrometer （FTIR）. The infrared region of 805--755 cm-1 was selected as quantitative area for determining fuel pollution level of aviation lubrication oil. Finally, correlation of the testing peak area and the fuel pollution level of corresponding samples were analyzed, and the regression equation was proposed. The results show that determining jet fuel pollution level of aviation lubricating oil by FTIR is feasible and reliable.

Optimization of broadband omnidirectional antireflection coatings for solar cells

Broadband and omnidirectional antireflection coating is generally an effective way to improve solar cell efficiency, because the destructive interference between the reflected and incident light can maximize the light transmission into the absorption layer. In this paper, we report the incident quantum efficiency ηin, not incident energy or power, as the evaluation function by the ant colony algorithm optimization method, which is a swarm-based optimization method. Also, SPCTRL2 is proposed to be incorporated for accurate optimization because the solar irradiance on a receiver plane is dependent on position, season, and time. Cities of Quito, Beijing and Moscow are selected for two-and three-layer antireflective coating optimization over λ = [300,1100] nm and θ = [0°, 90°]. The ηin increases by 0.26%, 1.37% and 4.24% for the above 3 cities, respectively, compared with that calculated by other rigorous optimization algorithms methods, which is further verified by the effect of position and time dependent solar spectrum on the antireflective coating design.

Continuous-wave mid-infrared intracavity singly resonant optical parametric oscillator based on periodically poled lithium niobate

This paper reports a continuous-wave （CW） mid-infrared intracavity singly resonant optical parametric oscillator based on periodically poled lithium niobate （PPLN） pumped by a diode-end-pumped CW Nd：YVO4 laser. Considering the thermal lens effects, it adopted an optical ballast lens and the near-concentric cavity for better operation. At the PPLN＇s grating period of 28.5 μm and the temperature of 140℃, the maximum idler output power of 155 mW at 3.86 μm has been achieved when the 808 nm pump power is 8.5 W, leading to an optical-to-optical conversion efficiency of 1.82%.

Up-conversion detection of mid-infrared light carrying orbital angular momentum

Frequency up-conversion is an effective method of mid-infrared(MIR) detection by converting long-wavelength photons to the visible domain, where efficient detectors are readily available. Here, we generate MIR light carrying orbital angular momentum(OAM) from a difference frequency generation process and perform up-conversion on it via sum frequency conversion in a bulk quasi-phase-matching crystal. The maximum quantum conversion efficiencies from MIR to visible are 34.0%, 10.4%, and 3.5% for light with topological charges of 0, 1, and 2, respectively, achieved by utilizing an optimized strong pump light. We also verify the OAM conservation with a specially designed interferometer, and the results agree well with the numerical simulations. Our study opens up the possibilities for generating, manipulating, and detecting MIR light that carries OAM, and will have great potential for optical communications and remote sensing in the MIR regime.

Design of wideband graded-index antireflection coatings at oblique light incidence

We suggest a design method of graded-refractive-index （GRIN） antireflection （AR） coating for s-polarized or p- polarized light at off-normal incidence. The spectrum characteristic of the designed antireflection coating with a quintic effective refractive-index profile for a given state of polarization has been discussed. In addition, the genetic algorithm was used to optimize the refractive index profile of the GRIN antireflection for reducing the mean reflectance of s- and p-polarizations. The average reflectance loss was reduced to only 0.04% by applying optimized GRIN AR coatings onto BK7 glass over the wavelength range from 400 to 800 nm at the incident angle of θo = 70°.

Wideband mid-infrared thermal emitter based on stacked nanocavity metasurfaces

Efficient thermal radiation in the mid-infrared(M-IR)region is of supreme importance for many applications including thermal imaging and sensing,thermal infrared light sources,infrared spectroscopy,emissivity coatings,and camouflage.The ability to control light makes metasurfaces an attractive platform for infrared applications.Recently,different metamaterials have been proposed to achieve high thermal radiation.To date,broadening the radiation bandwidth of a metasurface emitter(meta-emitter)has become a key goal to enable extensive applications.We experimentally demonstrate a broadband M-IR thermal emitter using stacked nanocavity metasurface consisting of two pairs of circular-shaped dielectric(Si;N;)–metal(Au)stacks.A high thermal radiation can be obtained by engineering the geometry of nanocavity metasurfaces.Such a meta-emitter provides wideband and broad angular absorptance of both p-and s-polarized light,offering a wideband thermal radiation with an average emissivity of more than 80%in the M-IR atmospheric window of 8–14μm.The experimental illustration together with the theoretical framework establishes a basis for designing broadband thermal emitters,which,as anticipated,will initiate a promising avenue to M-IR sources.

A novel 2-μm pulsed fiber laser based on a supercontinuum source and its application to mid-infrared supercontinuum generation

A new method to achieve 2-μm pulsed fiber lasers based on a supercontinuum （SC） is demonstrated. The incident pump light is a pulsed SC which contains a pump light and a signal light at the same time. The initial signal of the seed laser is provided by the incident pump light and amplified in the cavity. Based on this, we obtain a 2-μm pulsed laser with pulse repetition rate of 50 kHz and pulse width of 2 ns from the Tm-doped fiber laser. This 2-μm pulsed laser is amplified by two stages of fiber amplifiers, then the amplified laser is used for mid-infrared （mid-IR） SC generation in a 10-m length of ZrF4-BaF2-LaF3-AIF3-NaF （ZBLAN） fiber. An all-fiber-integrated mid-IR SC with spectrum ranging from 1.8 ~tm to 4.3 μm is achieved. The maximal average output power of the mid-IR SC from the ZBLAN fiber is 1.24 W （average output power beyond 2.5 μm is 340 mW）, corresponding to an output efficiency of 6.6% with respect to the 790-nm pump power.

High performance GaSb based digital-grown InGaSb/AlGaAsSb mid-infrared lasers and bars

InGaSb/AlGaAsSb double-quantum-well diode lasers emitting around 2 μm are demonstrated. The AlGaAsSb barriers of the lasers are grown with digital alloy techniques consisting of binary AlSb/AlAs/GaSb short-period pairs. Peak power conversion efficiency of 26% and an efficiency higher than 16% at 1 W are achieved at continuous-wave operation for a 2-mm-long and 100-μm-wide stripe laser. The maximum output power of a single emitter reaches to 1.4 W at 7 A.19-emitter bars with maximum efficiency higher than 20% and maximum power of 16 W are fabricated. Lasers with the short-period-pair barriers are proved to have improved temperature properties and wavelength stabilities. The characteristic temperature(T_0) is up to 140?C near room temperature(25–55?C).

Theoretical study and optimization of a high power mid-infrared erbium-doped ZBLAN fibre laser

Based on the rate equations describing the erbium-doped fluoride glass （ZBLAN） fibre lasers with different pumping configurations being taken into account, this paper presents theoretical calculations related to the dynamic population density and the operation performance of a high power mid-infrared all-fibre erbium-doped ZBLAN fibre laser. It shows that the ground-state absorption, excited-state absorption and energy-transfer-upconversion processes co-exist and produce a population balance, causing the laser to operate stably at a continuous wave state. A good agreement between the theoretical results and recent experimental measurement is obtained. Furthermore, the laser structure parameters including fibre length, reflectance of output fibre Bragg grating and pumping configurations are quantitatively optimised to achieve the best performance. The results show, as expected, that the slope efficiency of the fibre laser can be improved significantly through optimisation, which then provides an important guide for the design of high-performance mid-infrared erbium-doped ZBLAN fibre lasers.

Research on Determination of Nitrogen Content in Petroleum Using Mid-infrared Spectroscopy

Nitrogen content is an important parameter for petroleum refining processes. The combined use of mid-infrared attenuated total reflection spectroscopy and multivariate calibration allows accurate determination of nitrogen content in petroleum and its products. The calibration models of nitrogen content in crude oils have been established by partial least squares (PLS) method. The results predicted by this method were very close to those determined by standard methods. Compared with standard methods, this method is provided with advantages such as high-speed, simplicity and good-repeat- ability without any needs for pretreatment.

Mid-infrared supercontinuum generation and its application on all-optical quantization with different input pulses

Supercontinuum generation(SCG) and its application on all-optical quantization of all-optical analog-to-digital conversions(AOADCs) at the mid-infrared region in an Al GaAs strip waveguide are investigated numerically. The simulation results show that when the parabolic pulse is input, not only broader and higher-coherence SCG is obtained and a higher effective number of bits(ENOB) can be achieved, compared with the input pulse with hyperbolic-secant and Gaussian shaping. A four-bit quantization resolution is achieved along with a signal-to-noise ratio of 24.02 dB and an ENOB of3.99 bit, and the required input peak power is 760 mW.

Highly-sensitive NO,NO2,and NH3 measurements with an open-multipass cell based on mid-infrared wavelength modulation spectroscopy

A compact prototype based on mid-infrared wavelength modulation spectroscopy（WMS）is developed for the simul-taneous monitoring of NO,NO2,and NH3 in the urban area.Three quantum cascade lasers（QCLs）with central frequencies around 1900.0 cm^-1,1600.0 cm^-1,and 1103.4 cm^-1are used for NO,NO2,and NH3detections,respectively,by timedivision multiplex.An open-path multi-pass cell of 60-m optical path length is applied to the instrument for high sensitivity and reducing the response time to less than 1 s.The prototype achieves a sub-ppb detection limit for all the three target gases with an average time of about 100 s.The instrument is installed in the Jiangsu environmental monitoring center to conduct performance tests on ambient air.Continuous 24-hour measurements show good agreement with the results of a reference instrument based on the chemiluminescence technique.

The application of Fourier transform mid-infrared(FTIR) spectroscopy to identify variation in cell wall composition of Setaria italica ecotypes

Cell wall composition in monocotyledonous grasses has been identified as a key area of research for developing better feedstocks for forage and biofuel production.Setaria viridis and its close domesticated relative Setaria italica have been chosen as suitable monocotyledonous models for plants possessing the C4 pathway of photosynthesis including sorghum,maize,sugarcane,switchgrass and Miscanthus×giganteus.Accurate partial least squares regression（PLSR）models to predict S.italica stem composition have been generated,based upon Fourier transform mid-infrared（FTIR）spectra and calibrated with wet chemistry determinations of ground S.italica stem material measured using a modified version of the US National Renewable Energy Laboratory（NREL）acid hydrolysis protocol.The models facilitated a high-throughput screening analysis for glucan,xylan,Klason lignin and acid soluble lignin（ASL）in a collection of 183 natural S.italica variants and clustered them into classes,some possessing unique chemotypes.The predictive models provide a highly efficient screening tool for large scale breeding programs aimed at identifying lines or mutants possessing unique cell wall chemotypes.Genes encoding key catalytic enzymes of the lignin biosynthesis pathway exhibit a high level of conservation with matching expression profiles,measured by RT-q PCR,among accessions of S.italica,which closely mirror profiles observed in the different developmental regions of an elongating internode of S.viridis by RNASeq.

Laser Wakefield Acceleration Using Mid-Infrared Laser Pulses

We study a laser wakefield acceleration driven by mid-infrared （mid-IR） laser pulses through two-dimensional particle-in-cell simulations. Since a mid-IR laser pulse can deliver a larger ponderomotive force as compared with the usual 0.8 μm wavelength laser pulse, it is found that electron self-injection into the wake wave occurs at an earlier time, the plasma density threshold for injection becomes lower, and the electron beam charge is substantially enhanced. Meanwhile, our study also shows that quasimonoenergetic electron beams with a narrow energy-spread can be generated by using mid-IR laser pulses. Such a mid-IR laser pulse can provide a feasible method for obtaining a high quality and high charge electron beam. Therefore, the current efforts on constructing mid-IR terawatt laser systems can greatly benefit the laser wakefield acceleration research.

High-Efficiency Mid-Infrared Picosecond MgO:PPLN Single Resonant Optical Parametric Oscillator

We demonstrate a high-emciency mid-infrared picosecond optical parametric oscillator （OPO） based on MgO doped periodically poled lithium niobate （MgO：PPLN） with a laser diode array （LDA） pumped Innoslab amplifier as the pumping source. Under a 16 W synchronously pumping power, 4.5 W of idler light at 2896nm is obtained. A tuning range of idler light from 2688nm to 3016nm is achieved, within which the highest optical-optical conversion ettlciency from pump power to OPO output is 35.1%. Moreover, a signal light of -500mW from 1644 to 1700nm with a repetition rate of 233.8 MHz is generated.

Single-shot mid-infrared incoherent holography using Lucy-Richardson-Rosen algorithm

In recent years,there has been a significant transformation in the field of incoherent imaging with new possibilities of compressing three-dimensional(3D)information into a two-dimensional intensity distribution without two-beam interference(TBI).Most of the incoherent 3D imagers without TBI are based on scattering by a random phase mask exhibiting sharp autocorrelation and low cross-correlation along the depth.Consequently,during reconstruction,high lateral and axial resolutions are obtained.Imaging based on scattering requires an astronomical photon budget and is therefore precluded in many power-sensitive applications.In this study,a proof-of-concept 3D imaging method without TBI using deterministic fields has been demonstrated.A new reconstruction method called the Lucy-Richardson-Rosen algorithm has been developed for this imaging concept.We believe that the proposed approach will cause a paradigm-shift in the current state-of-the-art incoherent imaging,fluorescence microscopy,mid-infrared fingerprinting,astronomical imaging,and fast object recognition applications.

Ultrabroadband mid-infrared emission from Cr^(2+):ZnSe-doped chalcogenide glasses prepared via hot uniaxial pressing and melt-quenching

We reported an ultrabroadband mid-infrared(MIR)emission in the range of 1800 nm-3100 nm at room temperature(RT)from a Cr^(2+):ZnSe-doped chalcogenide glasses(ChGs)and studied the emission-dependent properties on the doping methods.A series of Cr^(2+):ZnSe/As_(40)S_(57)Se_(3)(in unit wt.%)glass-ceramics were prepared by hot uniaxial pressing(HUP)and melt-quenching methods,respectively.The glass-ceramics with MIR emission bands greater than 1000 nm were successfully prepared by both methods.The effects of matrix glass composition and grain doping concentration on the optical properties of the samples were studied.The occurrence state,morphology of the grains,and the microscopic elemental distributions were characterized using x-ray diffraction(XRD),scanning electron microscope(SEM),and energy dispersive spectrometer(EDS)analyses.

MOF/Polymer-Integrated Multi-Hotspot Mid-Infrared Nanoantennas for Sensitive Detection of CO_(2) Gas

Metal-organic frameworks(MOFs)have been extensively used for gas sorption,storage and separation owing to ultrahigh porosity,exceptional thermal stability,and wide structural diversity.However,when it comes to ultra-low concentration gas detection,technical bottlenecks of MOFs appear due to the poor adsorption capacity at ppm-/ppblevel concentration and the limited sensitivity for signal transduction.Here,we present hybrid MOF-polymer physi-chemisorption mechanisms integrated with infrared(IR)nanoantennas for highly selective and ultrasensitive CO_(2) detection.To improve the adsorption capacity for trace amounts of gas molecules,MOFs are decorated with amino groups to introduce the chemisorption while maintaining the structural integrity for physisorption.Additionally,leveraging all major optimization methods,a multi-hotspot strategy is proposed to improve the sensitivity of nanoantennas by enhancing the near field and engineering the radiative and absorptive loss.As a benefit,we demonstrate the competitive advantages of our strategy against the state-of-the-art miniaturized IR CO_(2) sensors,including low detection limit,high sensitivity(0.18%/ppm),excellent reversibility(variation within 2%),and high selectivity(against C_(2)H_(5)OH,CH_(3)OH,N_(2)).This work provides valuable insights into the integration of advanced porous materials and nanophotonic devices,which can be further adopted in ultra-low concentration gas monitoring in industry and environmental applications.