A 37 GHz Millimeter-Wave Antenna Array for 5G Communication Terminals

This work presents,design and specific absorption rate(SAR)analysis of a 37GHz antenna,for 5th Generation(5G)applications.The proposed antenna comprises of 4-elements of rectangular patch and an even distribution.The radiating element is composed of copper material supported by Rogers RT5880 substrate of thickness,0.254 mm,dielectric constant(εr),2.2,and loss tangent,0.0009.The 4-elements array antenna is compact in size with a dimension of 8mm×20mm in length and width.The radiating patch is excited with a 50 ohms connector i.e.,K-type.The antenna resonates in the frequency band of 37 GHz,that covers the 5G applications.The antenna behavior is studied both in free space and in the proximity of the human body.Three models of the human body,i.e.,belly,hand,and head(contain skin,fat,muscles,and bone)are considered for on-body simulations.At resonant frequency,the antenna gives a boresight gain of 11.6 dB.The antenna radiates efficiently with a radiated efficiency of more than 90%.Also,it is observed that the antenna detunes to the lowest in the proximity of the human body,but still a good impedance matching is achieved considering the−10 dB criteria.Moreover,SAR is also being presented.The safe limit of 2 W/kg for any 10 g of biological tissue,specified by the European International Electro Technical Commission(IEC)has been considered.The calculated values of SAR for human body models,i.e.,belly,hand and head are 1.82,1.81 and 1.09 W/kg,respectively.The SAR values are less than the international recommendations for the three models.Furthermore,the simulated and measured results of the antenna are in close agreement,which makes it,a potential candidate for the fifth-generation smart phones and other handheld devices.

Design of Millimeter-Wave Antenna-in-Package(AiP)for 5G NR

For 5G new radio(NR),there are two frequency bands:Frequency Range 1(FR‐1)(low frequency)and Frequency Range 2(FR‐2)(millimeter‐wave frequency).Millimeter‐wave has been officially utilized in mobile applications.The wide bandwidth is the key for the millimeter-wave band.However,higher loss has become the major challenge for the wide use of this frequency range.Antenna array and beamforming technologies have been introduced to resolve the path loss and coverage problems.The key design considerations of the beamforming antenna array are low loss,compact system and small size.Antenna-in-package(AiP)has become the most attractive technology for millimeter-wave front-end system.For the design of AiP,many parameters such as RF transition,material and heat need to be considered and designed properly.The Over‐the‐Air(OTA)testing technology is also very critical for AiP mass production.In this paper,the detail of AiP design and new OTA testing technology are discussed and demonstrated.

Co-Sharing Waveform Design for Millimeter-Wave Radar Communication Systems

Millimeter-wave(mmWave)radar communication has emerged as an important technique for future wireless systems.However,the interference between the radar signal and communication data is the main issue that should be considered for the joint radar communication system.In this paper,a co-sharing waveform(CSW)is proposed to achieve communication and radar sensing simultaneously.To eliminate the co-interference between the communication and sensing signal,signal splitting and processing methods for communication data demodulation and radar signal processing are given respectively.Simulation results show that the bit error rate(BER)of CSW is close to that of the pure communication waveform.Moreover,the proposed CSW can achieve better performance than the existing waveforms in terms of range and velocity estimation.

Computer Modelling of Compact 28/38 GHz Dual-Band Antenna for Millimeter-Wave 5G Applications

A four-element compact dual-band patch antenna having a common ground plane operating at 28/38 GHz is proposed formillimeter-wave communication systems in this paper.Themultiple-input-multiple-output(MIMO)antenna geometry consists of a slotted ellipse enclosed within a hollow circle which is orthogonally rotated with a connected partial ground at the back.The overall size of the four elements MIMO antenna is 2.24λ×2.24λ(at 27.12GHz).The prototype of four-element MIMOresonator is designed and printed using Rogers RTDuroid 5880 withε_(r)=2.2 and loss tangent=0.0009 and having a thickness of 0.8 mm.It covers dual-band having a fractional bandwidth of 15.7%(27.12-31.34 GHz)and 4.2%(37.21-38.81 GHz)for millimeter-wave applications with a gain of more than 4 dBi at both bands.The proposed antenna analysis in terms ofMIMOdiversity parameters(Envelope Correlation Coefficient(ECC)and Diversity Gain(DG))is also carried out.The experimental result in terms of reflection coefficient,radiation pattern,gain and MIMOdiversity parameter correlates very well with the simulated ones that show the potential of the proposed design for MIMO applications at millimeter-wave frequencies.

Wide-Angle Scanning Antennas for Millimeter-Wave 5G Applications

The fifth generation(5G)network communication systems operate in the millimeter waves and are expected to provide a much higher data rate in the multi-gigabit range,which is impossible to achieve using current wireless services,including the sub-6 GHz band.In this work,we briefly review several existing designs of millimeter-wave phased arrays for 5G applications,beginning with the low-profile antenna array designs that either are fixed beam or scan the beam only in one plane.We then move on to array systems that offer two-dimensional(2D)scan capability,which is highly desirable for a majority of 5G applications.Next,in the main body of the paper,we discuss two different strategies for designing scanning arrays,both of which circumvent the use of conventional phase shifters to achieve beam scanning.We note that it is highly desirable to search for alternatives to conventional phase shifters in the millimeter-wave range because legacy phase shifters are both lossy and costly;furthermore,alternatives such as active phase shifters,which include radio frequency amplifiers,are both expensive and power-hungry.Given this backdrop,we propose two different antenna systems with potential for the desired 2D scan performance in the millimeter-wave range.The first of these is a Luneburg lens,which is excited either by a 2D waveguide array or by a microstrip patch antenna array to realize 2D scan capability.Next,for second design,we turn to phased-array designs in which the conventional phase shifter is replaced by switchable PIN diodes or varactor diodes,inserted between radiating slots in a waveguide to provide the desired phase shifts for scanning.Finally,we discuss several approaches to enhance the gain of the array by modifying the conventional array configurations.We describe novel techniques for realizing both one-dimensional(1D)and 2D scans by using a reconfigurable metasurface type of panels.

Design and Analysis of Novel Antenna for Millimeter-Wave Communication

At present,the microwave frequency band bandwidth used for mobile communication is only 600 MHz.In 2020,the 5G mobile Communication required about 1 GHz of bandwidth,so people need to tap new spectrum resources to meet the development needs of mobile Internet traffic that will increase by 1,000 times in the next 10 years.Utilize the potentially large bandwidth(30∼300 GHz)of the millimeter wave frequency band to provide higher data rates is regarded as the potential development trend of the future wireless communication technology.A microstrip patch implementation approach based on electromagnetic coupling feeding is presented to increase the bandwidth of a dual-polarized millimeter-wave antenna.To extend the antenna unit's impedance bandwidth,coplanar parasitic patches and spatial parallel parasitic patches are used,and a 22 sub-array antenna is developed using paired inverse feed technology.The standing wave at the centre frequency of 37.5 GHz is less than 2 GHz.The antenna array's relative bandwidth is 6.13 percent,the isolation is>30 dB,the cross-polarization is−23.6 dB,and the gain is 11.5 dBi,according to the norm.The proposed dual-polarized microstrip antenna has the characteristics of wide frequency bandwidth,large port isolation,low cross-polarization,and high gain.The antenna performance meets the general engineering requirements of millimeter-wave dual-polarized antennas.

Analysis and design of novel wideband and high efficiency millimeter-wave antenna arrays for 60-GHz applications

A type of millimeter-wave antenna array with flexible design is proposed for a variety of applications at 60 GHz.The antenna array can be adjusted to be linearly or circularly polarized by simply changing the radiation part of the antenna array.High gain,wideband,and high radiation efficiency characteristics can be achieved by adopting a low insertion loss feeding network and broadband antenna elements.For the linearly polarized antenna array,simulation results show that the impedance bandwidth of the 2×2 antenna subarray reaches 21.6%,while the maximum gain achieves 15.1 dBi and has a fluctuation of less than 0.4 dBi within the working bandwidth.Simulation results of the 8×8 linearly polarized antenna array show a bandwidth of 21.6%and a gain of(26.1±1)dBi with an antenna efficiency of more than 80%.For the 8×8 circularly polarized antenna array,simulation results show that an impedance bandwidth of 18.2%and an axial ratio(AR)bandwidth of 13.3%are obtained.Gain and efficiency of up to 27.6 dBi and 80%are achieved,respectively.A prototype of antenna array is fabricated,and results are compared and analyzed.

Wideband Reconfigurable Millimeter-Wave Linear Array Antenna Using Liquid Crystal for 5G Networks

The advanced design of a 10 × 1 linear antenna array system with the capa-bility of frequency tunability using GT3-23001 liquid crystal (LC) is pro-posed. The design for this reconfigurable wideband antenna array for 5G ap-plications at Ka-band millimeter-wave (mmw) consists of a double layer of stacked patch antenna with aperture coupled feeding. The bias voltage over LC varies from 0 V to 10.6 V to achieve a frequency tunability of 1.18 GHz. The array operates from 25.3 GHz to 33.8 GHz with a peak gain of 19.2 dB and a beamwidth of 5.2° at 30 GHz. The proposed reconfigurable antenna ar-ray represents a real and efficient solution for the recent and future mmw 5G networks. The proposed antenna is suitable for 5G base stations in stadiums, malls and convention centers. It is proper for satellite communications and radars at mmw.

Non-LOS target localization via millimeter-wave automotive radar

This paper considers the non-line-of-sight(NLOS)vehicle localization problem by using millimeter-wave(MMW)automotive radar.Several preliminary attempts for NLOS vehicle detection are carried out and achieve good results.Firstly,an electromagnetic(EM)wave NLOS multipath propagation model for vehicle scene is established.Subsequently,with the help of available multipath echoes,a complete NLOS vehicle localiza-tion algorithm is proposed.Finally,simulation and experimental results validate the effectiveness of the established EM wave propagation model and the proposed NLOS vehicle localization algorithm.

A Compact UHF Antenna Based on Hilbert Fractal Elements and a Serpentine Arrangement for Detecting Partial Discharg

Efforts to protect electric power systems from faults have commonly relied on the use of ultra-high frequency(UHF)antennas for detecting partial discharge(PD)as a common precursor to faults.However,the effectiveness of existing UHF antennas suffers from a number of challenges such as limited bandwidth,relatively large physical size,and low detection sensitivity.The present study addresses these issues by proposing a compact microstrip patch antenna with fixed dimensions of 100 mm×100 mm×1.6 mm.The results of computations yield an optimized antenna design consisting of 2nd-order Hilbert fractal units positioned within a four-layer serpentine arrangement with a fractal unit connection distance of 3.0 mm.Specifically,the optimized antenna design achieves a detection bandwidth for which the voltage standing wave ratio is less than 2 that is approximately 97.3%of the UHF frequency range(0.3–3 GHz).Finally,a prototype antenna is fabricated using standard printed circuit board technology,and the results of experiments demonstrate that the proposed antenna is capable of detecting PD signals at a distance of 8 m from the discharge source.

Assessment of the performance of the TOPGNSS and ANN-MB antennas for ionospheric measurements using low-cost u-blox GNSS receivers

Low-cost GNSS receivers have recently been gaining reliability as good candidates for ionospheric studies. In line with these gains are genuine concerns about improving the performance of these receivers. In this work, we present a comprehensive investigation of the performances of two antennas(the u-blox ANN-MB and the TOPGNSS TOP-106) used on a low-cost GNSS receiver known as the u-blox ZED-F9P. The two antennas were installed on two identical and co-located u-blox receivers. Data used from both receivers cover the period from January to June 2022. Results from the study indicate that the signal strengths are dominantly greater for the receiver with the TOPGNSS antenna than for the receiver with the ANN-MB antenna, implying that the TOPGNSS antenna is better than the ANN-MB antenna in terms of providing greater signal strengths. Summarily, the TOPGNSS antenna also performed better in minimizing the occurrence of cycle slips on phase TEC measurements. There are no conspicuous differences between the variances(computed as 5-min standard deviations) of phase TEC measurements for the two antennas, except for a period around May-June when the TOPGNSS gave a better performance in terms of minimizing the variances in phase TEC. Remarkably, the ANN-MB antenna gave a better performance than the TOPGNSS antenna in terms of minimizing the variances in pseudorange TEC for some satellite observations. For precise horizontal(North and East) positioning, the receiver with the TOPGNSS antenna gave better results, while the receiver with the ANN-MB antenna gave better vertical(Up) positioning. The errors for the receivers of both antennas are typically within about 5 m(the monthly mean was usually smaller than 1 m) in the horizontal direction and within about 10 m(the monthly mean was usually smaller than 4 m) in the vertical direction.

Prediction of Bandwidth of Metamaterial Antenna Using Pearson Kernel-Based Techniques

The use of metamaterial enhances the performance of a specific class of antennas known as metamaterial antennas.The radiation cost and quality factor of the antenna are influenced by the size of the antenna.Metamaterial antennas allow for the circumvention of the bandwidth restriction for small antennas.Antenna parameters have recently been predicted using machine learning algorithms in existing literature.Machine learning can take the place of the manual process of experimenting to find the ideal simulated antenna parameters.The accuracy of the prediction will be primarily dependent on the model that is used.In this paper,a novel method for forecasting the bandwidth of the metamaterial antenna is proposed,based on using the Pearson Kernel as a standard kernel.Along with these new approaches,this paper suggests a unique hypersphere-based normalization to normalize the values of the dataset attributes and a dimensionality reduction method based on the Pearson kernel to reduce the dimension.A novel algorithm for optimizing the parameters of Convolutional Neural Network(CNN)based on improved Bat Algorithm-based Optimization with Pearson Mutation(BAO-PM)is also presented in this work.The prediction results of the proposed work are better when compared to the existing models in the literature.

Microstrip Patch Antenna with an Inverted T-Type Notch in the Partial Ground for Breast Cancer Detections

This study designs a microstrip patch antenna with an inverted T-type notch in the partial ground to detect tumorcells inside the human breast.The size of the current antenna is small enough(18mm×21mm×1.6mm)todistribute around the breast phantom.The operating frequency has been observed from6–14GHzwith a minimumreturn loss of−61.18 dB and themaximumgain of current proposed antenna is 5.8 dBiwhich is flexiblewith respectto the size of antenna.After the distribution of eight antennas around the breast phantom,the return loss curveswere observed in the presence and absence of tumor cells inside the breast phantom,and these observations showa sharp difference between the presence and absence of tumor cells.The simulated results show that this proposedantenna is suitable for early detection of cancerous cells inside the breast.

Array (Smart) Antennas Improve GSM Performance

As wireless data applications over cellular networks become more widespread, the pressure to increase capacity will become even more intense. Capacity in the 800 and 900 MHz bands, where bandwidth is restricted, is already becoming a limiting factor. This paper attempts to address how the application of smart antenna systems has brought about improvements in call quality and increased capacity through reduced Interference in Mobile Communication. The smart antenna may be in a variety of ways to improve the performance of a communications system. Perhaps most importantly is its capability to cancel co-channel interference. It helps in improving the system performance by increasing the channel capacity, spectrum efficiency, extending range coverage, speech quality, enabling tighter reuse of frequencies within a cellular network and economically, feasible increased signal gain, greater, reduced multipath reflection. It has been argued that Smart antennas and the Algorithms to control them are vital to a high-capacity communication system development.

IMPROVED PERTURBATION ANALYSIS OF MILLIMETER-WAVE DIELEC TRIC GRATING LEAKY WAVE ANTENNA

An improved perturbation procedure is used for analyzing the radiation character-istics of the millimeter wave dielectric grating leaky wave antenna. The electromagnetic fields aredescribed in terms of an active transverse transmission line network, which brings considerablephysical insight into the overall behavior of the antenna. The analysis is simple and practical. Itsaccuracy is as high as the rigorous method.

A Combined Antenna Array Deployment with High Positioning Accuracy and Low Angular Measurement Error

In this paper,an antenna array composed of circular array and orthogonal linear array is proposed by using the design of long and short baseline“orthogonal linear array”and the circular array ambiguity resolution design of multi-group baseline clustering.The effectiveness of the antenna array in this paper is verified by sufficient simulation and experiment.After the system deviation correction work,it is found that in the L/S/C/X frequency bands,the ambiguity resolution probability is high,and the phase difference system error between each channel is basically the same.The angle measurement error is less than 0.5°,and the positioning error is less than 2.5 km.Notably,as the center frequency increases,calibration consistency improves,and the calibration frequency points become applicable over a wider frequency range.At a center frequency of 11.5 GHz,the calibration frequency point bandwidth extends to 1200 MHz.This combined antenna array deployment holds significant promise for a wide range of applications in contemporary wireless communication systems.

Adaptive Thermoforming and Structural Design of Millimeter-Wave Antenna Panels

Future large-scale radio telescope observatories,such as the next-generation Very Large Array,involve extremely large collection areas.These collection areas are divided into smaller shaped panels,which typically require their own unique molds to manufacture.For these projects to be cost-effective,an efficient fabrication method for the shaped panels is needed.This paper outlines the development and success of a novel adaptive freeform panel molding technology that greatly improves manufacturing efficiency due to its repeatable and reusable nature.Moreover,it presents an analysis of a proposed panel structural design for the shaped panels,which incorporates a study on surface deformation due to gravity and wind loading under realistic operational conditions.

Optimization of the Physical Aperture of the Parabolic Reflector Antenna

In fields like astronomy and radar technology, high-gain antennas are required for long-distance communication. Due to its relatively large gain, the use of parabolic antennas has become very popular over time, because they can easily achieve gains of above 30 dB at microwave and higher frequencies. Today, most systems’ success depends on how well the antennas perform. These antennas are available in different types and sizes. Each antenna’s effective area usually has less than the actual physical area of the antenna surface. This means that the unused area of the antenna is massive, and a waste. The aim of the research is to show that the actual physical aperture of a parabolic antenna can be reduced as much as possible to equal the effective area, as given by the antenna formula, thereby saving manufacturing costs, improve the aesthetics. In other words, the focus of this work is to experimentally show that reflector antenna can be made of smaller sizes but better performance. Measurements were taken from different positions from a parabolic antenna, the signal level measured and compared with signal levels for optimal performance.

Design of Quasi-Optical Lens Antenna for W-Band Short Range Passive Millimeter-Wave Imaging

A quasi-optical dielectric lens used for W-band focal plane array passive imaging has been developed. The imaging system requires the lens to form beam spot with 3 dB width less than 35 mm at distance of 3500 mm. The powerful optical design software ZEMAX was utilized to design the contours of the lens, and numerical method based on ray tracing and Huygens’ Principle was processed to verify the design result. Measurement result shows that the 3 dB width of the beam spot formed by the lens is 34 mm at distance of 3460 mm, and the beam pattern on imaging plane are equally arranged and the intensity decreases only 0.55 dB while the object lateral deviation increases to 300 mm.

New Antenna Array Beamforming Techniques Based on Hybrid Convolution/Genetic Algorithm for 5G and Beyond Communications

Side lobe level reduction(SLL)of antenna arrays significantly enhances the signal-to-interference ratio and improves the quality of service(QOS)in recent and future wireless communication systems starting from 5G up to 7G.Furthermore,it improves the array gain and directivity,increasing the detection range and angular resolution of radar systems.This study proposes two highly efficient SLL reduction techniques.These techniques are based on the hybridization between either the single convolution or the double convolution algorithms and the genetic algorithm(GA)to develop the Conv/GA andDConv/GA,respectively.The convolution process determines the element’s excitations while the GA optimizes the element spacing.For M elements linear antenna array(LAA),the convolution of the excitation coefficients vector by itself provides a new vector of excitations of length N=(2M−1).This new vector is divided into three different sets of excitations including the odd excitations,even excitations,and middle excitations of lengths M,M−1,andM,respectively.When the same element spacing as the original LAA is used,it is noticed that the odd and even excitations provide a much lower SLL than that of the LAA but with amuch wider half-power beamwidth(HPBW).While the middle excitations give the same HPBWas the original LAA with a relatively higher SLL.Tomitigate the increased HPBWof the odd and even excitations,the element spacing is optimized using the GA.Thereby,the synthesized arrays have the same HPBW as the original LAA with a two-fold reduction in the SLL.Furthermore,for extreme SLL reduction,the DConv/GA is introduced.In this technique,the same procedure of the aforementioned Conv/GA technique is performed on the resultant even and odd excitation vectors.It provides a relatively wider HPBWthan the original LAA with about quad-fold reduction in the SLL.