PHASE-LOCKED 2-D JOSEPHSON JUNCTION ARRAYS AS SUBMILLIMETER OSCILLATORS

This letter presents the results of numerical simulations for phase-locked 2-D Joseph-son junction array oscillator. The simulation result shows that the junctions of 2-D array can mutually phase-locked in a considerable area if the parameters can be carefully selected. The oscillators are formed with up to 33 identical Nb/AIOx/Nb junctions, and the junctions are connected with Nb microstrip resonators. Optimum structure parameters for oscillator circuit design can be obtained with these simulation results.

PHASE-LOCKING OF HIGH POWER GYROTRON OSCILLATOR

The phase-locking process is studied for high-power gyrotron oscillator driven by an external signal. The phase-locking nonlinear differential equations are derived, and the condition of phase-locking is shown and analyzed. The phase-locking signal can be introduced after gyrotron oscillates into saturation or before it. Two different ways of inputting signal make markable influence on the phase-locking process, this phenomenon is discussed. In this paper, the numerical calculations and analysis are given for gyrotron TE13 mode.

Joint MAP channel estimation and data detection for OFDM in presence of phase noise from free running and phase locked loop oscillator

This paper addresses a computationally compact and statistically optimal joint Maximum a Posteriori(MAP)algorithm for channel estimation and data detection in the presence of Phase Noise(PHN)in iterative Orthogonal Frequency Division Multiplexing(OFDM)receivers used for high speed and high spectral efficient wireless communication systems.The MAP cost function for joint estimation and detection is derived and optimized further with the proposed cyclic gradient descent optimization algorithm.The proposed joint estimation and detection algorithm relaxes the restriction of small PHN assumptions and utilizes the prior statistical knowledge of PHN spectral components to produce a statistically optimal solution.The frequency-domain estimation of Channel Transfer Function(CTF)in frequency selective fading makes the method simpler,compared with the estimation of Channel Impulse Response(CIR)in the time domain.Two different time-varying PHN models,produced by Free Running Oscillator(FRO)and Phase-Locked Loop(PLL)oscillator,are presented and compared for performance difference with proposed OFDM receiver.Simulation results for joint MAP channel estimation are compared with Cramer-Rao Lower Bound(CRLB),and the simulation results for joint MAP data detection are compared with“NO PHN"performance to demonstrate that the proposed joint MAP estimation and detection algorithm achieve near-optimum performance even under multipath channel fading.

Design and implementation of digital closed-loop drive control system of a MEMS gyroscope

In order to effectively control the working state of the gyroscope in drive mode, the drive characteristics of the micro electromechanical system （MEMS） gyroscope are analyzed in principle. A novel drive circuit for the MEMS gyroscope in digital closed-loop control is proposed, which utilizes a digital phase-locked loop （PLL） in frequency control and an automatic gain control （AGC） method in amplitude control. A digital processing circuit with a field programmable gate array （FPGA） is designed and the experiments are carried out. The results indicate that when the temperature changes, the drive frequency can automatically track the resonant frequency of gyroscope in drive mode and that of the oscillating amplitude holds at a set value. And at room temperature, the relative deviation of the drive frequency is 0.624 ×10^-6 and the oscillating amplitude is 8.0 ×10^-6, which are 0. 094% and 18. 39% of the analog control program, respectively. Therefore, the control solution of the digital PLL in frequency and the AGC in amplitude is feasible.

A Fractional-N CMOS DPLL with Self-Calibration

A digital phase-locked loop （DPLL） based on a new digital phase-frequency detector is presented. The self-calibration technique is employed to acquire wide lock range,low jitter, and fast acquisition. The DPLL works from 60 to 600MHz at a supply voltage of 1.8V. It also features a fraetional-N synthesizer with digital 2nd-order sigma-delta noise shaping, which can achieve a short lock time,a high frequency resolution,and an improved phase-noise spectrum. The DPLL has been implemented in SMIC 0. 18μm 1.8V 1P6M CMOS technology. The peak-to-peak jitter is less than 0. 8% of the output clock period and the lock time is less than 150 times of the reference clock period after the pre-divider.

A 5-GHz frequency synthesizer with constant bandwidth for low IF ZigBee transceiver applications

A fully integrated integer-N frequency synthesizer is implemented.The synthesizer is designed for low intermediate frequency （IF）ZigBee transceiver applications.Techniques used to make the loop bandwidth constant across the whole output frequency range of the voltage controlled oscillator（VCO）are adopted to maintain phase noise optimization and loop stability.In-phase and quadrature（IQ）signals are generated by a 1/2 frequency divider at the output of the VCO.The synthesizer is fabricated in 0.18 μm radio frequency（RF） complementary metal oxide semiconductor transistor （CMOS）technology.The chip area is 1.7 mm2.The synthesizer is measured on wafer.It consumes totally 28.8 mW excluding output buffers from a supply voltage of 1.8 V.The measured phase noise is -110 and -122 dBc/Hz at the offset of 1 and 3 MHz from a 2.405 GHz carrier,respectively.The measured reference spur at a 2 MHz offset from a 2.405 GHz carrier is-48.2 dBc.The measured setting time of the synthesizer is about 160 μs.

A time-domain digitally controlled oscillator composed of a free running ring oscillator and flying-adder

A time-domain digitally controlled oscillator （DCO） is proposed. The DCO is composed of a free-running ring oscillator （FRO） and a two lap-selectors integrated flying-adder （FA）. With a coiled cell array which allows uniform loading capacitances of the delay cells, the FRO produces 32 outputs with consistent tap spacing for the FA as reference clocks. The FA uses the outputs from the FRO to generate the output of the DCO according to the control number, resulting in a linear dependence of the output period, instead of the frequency on the digital controlling word input. Thus the proposed DCO ensures a good conversion linearity in a time-domain, and is suitable for time-domain all-digital phase locked loop applications. The DCO was implemented in a standard 0.13μm digital logic CMOS process. The measurement results show that the DCO has a linear and monotonic tuning curve with gain variation of less than 10%, and a very low root mean square period jitter of 9.3 ps in the output clocks. The DCO works well at supply voltages ranging from 0.6 to 1.2 V, and consumes 4 mW of power with 500 MHz frequency output at 1.2 V supply voltage.

A 0.5-1.7 GHz low phase noise ring-oscillator-based PLL for mixed-signal SoCs

This paper describes the design of a fully integrated low phase noise CMOS phase-locked loop for mixedsignal SoCs with a wide range of operating frequencies.The design proposes a multi-regulator PLL architecture,in which every noise-sensitive block from the PLL top level is biased from a dedicated linear or shunt regulator,reducing the parasitic noise and spur coupling between different PLL building blocks.Supply-induced VCO frequency sensitivity of the PLL is less than 0.07%-fvco/1%-VDD.The design is fabricated in 0.13μm 1.5/3.3 V CMOS technology.The in-band phase noise of -102 dBc/Hz at 1 MHz offset with a spur of less than -45 dBc is measured from 1.25 GHz carrier.The measured RMS jitter of the proposed PLL is 1.72 ps at a 1.25 GHz operating frequency.The total power consumption is 19 mW,and its active area is 0.19 mm^2.

ON INTERNAL RESONANCE OF NONLINEAR VIBRATING SYSTEMS WITH MANY DEGREES OF FREEDOM

The problem of periodic solutions of nonlinear autonomous systems with many degrees of freedom is considered. This is made possible by the development of a modified version of the KBM method[1]. The method can be used to generate limit cycle phase portrait, amplitude, period and to indicate stability of the limit cycle.

Chip design of a 5.8-GHz fractional-N frequency synthesizer with a tunable G_m-C loop filter

This paper proposes a novel Gm-C loop filter instead of a conventional passive loop filter used in a phase-locked loop. The innovative advantage of the proposed architecture is tunable loop filter bandwidth and hence the process variations of passive elements of resistance R and capacitance C can be overcome and the chip area is greatly reduced. Furthermore, the MASH 1-1-1 sigma-delta （ZA） modulator is adopted for performing the fractional division number and hence improves the phase noise as well. Measured results show that the locked phase noise is -114.1 dBc/Hz with lower Gm-C bandwidth and -111.7 dBm/C with higher Gm-C bandwidth at 1 MHz offset from carrier of 5.68 GHz. Including pads and built-in Gm-C filter, the chip area of the proposed frequency synthesizer is 1.06 mm2. The output power is -8.69 dBm at 5.68 CHz and consumes 56 mW with an off-chip buffer from 1.8-V supply voltage.

Design of 622 Mb/s Clock-recovery Monolithic IC for Optical Communication System

A monolithic clock-recovery circuit used in 622 Mb/s optical communication system is designed,which is based on the phase-locked loop theory,and uses bipolar transistor model.It overcomes the shortcoming of clock recovery method based on filter,and implements monolithic clock-recovery IC.The designed circuits include phase detector,voltage-controlled oscillator and loop filter.Among them,the voltage-control oscillator is a modified two-stage ring oscillator,which provides quadrature clock signals and presents wide voltage-controlled range and high voltage-controlling sensitivity.

A 1.2-to-1.4 GHz low-jitter frequency synthesizer for GPS application

A fully integrated frequency synthesizer with low jitter and low power consumption in 0.18 μm CMOS (complementary metal-oxide semiconductor) technology is proposed in this paper.The frequency synthesizer uses a novel single-end gain-boosting charge pump, a differential coupled voltage controlled oscillator (VCO) and a dynamic logic phase/frequency detecor (PFD) to acquire low output jitter.The output frequency range of the frequency synthesizer is up to 1 200 MHz to 1 400 MHz for GPS (global position system) application.The post simulation results show that the phase noise of VCO is only 127.1 dBc/Hz at a 1 MHz offset and the Vp-p jitter of the frequency synthesizer output clock is 13.65 ps.The power consumption of the frequency synthesizer not including the divider is 4.8 mW for 1.8 V supply and it occupies a 0.8 mm×0.7 mm chip area.

Switchable PLL Frequency Synthesizer andHot Carrier Effects

In this paper, a new strategy of switchable CMOS phase-locked loop frequency synthesizer is proposed to increase its tuning range. The switchable PLL which integrates two phase-locked loops with different tuning frequencies are designed and fabricated in 0.5 μm n-well CMOS process. Cadence/Spectre simulations show that the frequency range of the switchable phased-locked loop is between 320 MHz to 1.15 GHz. The experimental results show that the RMS jitter of the phase-locked loop changes from 26 ps to 123 ps as output frequency varies. For 700 MHz carrier frequency, the phase noise of the phase-locked loop reaches as low as ?81 dBc/Hz at 10 kHz offset frequency and ?104 dBc/Hz at 1 MHz offset frequency. A device degradation model due to hot carrier effects has been used to analyze the jitter and phase noise performance in an open loop voltage-controlled oscillator. The oscillation frequency of the voltage-controlled oscillator decreases by approximately 100 to 200 MHz versus the bias voltage and the RMS jitter increases by 40 ps under different phase-locked loop output frequencies after 4 hours of stress time.

A 3 to 5 GHz low-phase-noise fractional-N frequency synthesizer with adaptive frequency calibration for GSM/PCS/DCS/WCDMA transceivers

A low-phase-noise E-A fractional-N frequency synthesizer for GSM/PCS/DCS/WCDMA transceivers is presented. The voltage controlled oscillator is designed with a modified digital controlled capacitor array to extend the tuning range and minimize phase noise. A high-resolution adaptive frequency calibration technique is introduced to automatically choose frequency bands and increase phase-noise immunity. A prototype is implemented in 0.13 #m CMOS technology. The experimental results show that the designed 1.2 V wideband frequency synthesizer is locked from 3.05 to 5.17 GHz within 30 μs, which covers all five required frequency bands. The measured in-band phase noise are -89, -95.5 and -101 dBc/Hz for 3.8 GHz, 2 GHz and 948 MHz carriers, respectively, and accordingly the out-of-band phase noise are -121, -123 and -132 dBc/Hz at 1 MHz offset, which meet the phase-noise-mask requirements of the above-mentioned standards.

Millimeter wave band ultra wideband transmitter MMIC

This paper presents a new millimeter-wave （MMW） ultra wideband （UWB） transmitter MMIC which has been developed in an OMMIC 0.1 μm GaAs PHEMT foundry process （ft= 100 GHz） for 22-29 GHz vehicular radar systems. The transmitter is composed of an MMW negative resistance oscillator （NRO）, a power amplifier （PA）, and two UWB pulse generators （PGs）. In order to convert the UWB pulse signal to MMW frequency and reduce the total power consumption, the MMW NRO is driven by one of the UWB pulse generators and the power amplifier is triggered by another UWB pulse generator. The main advantages of this transmitter are： new design, simple architecture, high-precision distance measurements, infinite ON/OFF switch ratio, and low power consumption. The total power consumption of the transmitter MMIC is 218 mW with a peak output power of 5.5 dBm at 27 GHz.

A 0.8 V low power low phase-noise PLL

A low power and low phase noise phase-locked loop（PLL） design for low voltage（0.8 V） applications is presented.The voltage controlled oscillator（VCO） operates from a 0.5 V voltage supply,while the other blocks operate from a 0.8 V supply.A differential NMOS-only topology is adopted for the oscillator,a modified precharge topology is applied in the phase-frequency detector（PFD）,and a new feedback structure is utilized in the charge pump（CP） for ultra-low voltage applications.The divider adopts the extended true single phase clock DFF in order to operate in the high frequency region and save circuit area and power.In addition,several novel design techniques,such as removing the tail current source,are demonstrated to cut down the phase noise.Implemented in the SMIC 0.13μm RF CMOS process and operated at 0.8 V supply voltage,the PLL measures a phase noise of-112.4 dBc/Hz at an offset frequency of 1 MHz from the carrier and a frequency range of 3.166-3.383 GHz.The improved PFD and the novel CP dissipate 0.39 mW power from a 0.8 V supply.The occupied chip area of the PFD and CP is 100×100μm^2.The chip occupies 0.63 mm^2,and draws less than 6.54 mW from a 0.8 V supply.

Simulation and design of an X-band overmoded input cavity

The RF input cavity is an important component for velocity-modulating types of microwave device, providing velocity modulation and density modulation. Conventional RF input cavities, however, encounter the problem of power capacity in the high frequency band due to the scaling law of the working frequency and device size. In this paper, an X-band overmoded input cavity is proposed and investigated. A resonant reflector is employed to reflect the microwave and isolate the input cavity from the diode and RF extractor. The resonant property of the overmoded input cavity is proved by simulations and cold tests, with PIC simulation showing that with a beam voltage of 600 kV and current of 7 kA, an input power of 90 kW is sufficient to modulate the beam with a modulation depth of 3%.

A 220–1100 MHz low phase-noise frequency synthesizer with wide-band VCO and selectable I/Q divider

This paper presents a low phase-noise fractional-N frequency synthesizer which provides an inphase/quadrature-phase（I/Q） signal over a frequency range of 220–1100 MHz for wireless networks of industrial automation（WIA） applications. Two techniques are proposed to achieve the wide range. First, a 1.4–2.2 GHz ultralow gain voltage-controlled oscillator（VCO） is adopted by using 128 tuning curves. Second, a selectable I/Q divider is employed to divide the VCO frequency by 2 or 3 or 4 or 6. Besides, a phase-switching prescaler is proposed to lower PLL phase noise, a self-calibrated charge pump is used to suppress spur, and a detect-boosting phase frequency detector is adopted to shorten settling time. With a 200 k Hz loop bandwidth, lowest measured phase noise is 106 dBc/Hz at a 10 k Hz offset and 131 dBc/Hz at a 1 MHz offset. Fabricated in the TSMC 0.18 μm CMOS process, the synthesizer occupies a chip area of 1.2 mm^2, consumes only 15 m W from the 1.8 V power supply,and settles within 13.2 s. The synthesizer is optimized for the WIA applications, but can also be used for other short-range wireless communications, such as 433, 868, 916 MHz ISM band applications.