Experiments performed on the grwth of mixed crystals of rare earth tartrates (Y1-xSmx)2 (C4H4O6)3.zH2O (0≤x≤1) from silica gels at 35~40℃ and 25~30℃ employing single-diffusion technique. are discussed. The crysta...Experiments performed on the grwth of mixed crystals of rare earth tartrates (Y1-xSmx)2 (C4H4O6)3.zH2O (0≤x≤1) from silica gels at 35~40℃ and 25~30℃ employing single-diffusion technique. are discussed. The crystals maintain spherulitic morphology, irrespective of the value of x, concentration of upper and lower reactants, gel pH, gel age and gel temperature. Formation Of Liesegang rings in this system is a temperature dependent phenomenon. It is shown that with the increase of the value of x the system passes from Liesegangring phenomenon to singlezone phenomenon. Operative mechanism of crystallization in the higher (35~40℃) and lower temperature ranges (25~30℃) is explained. Seeded growth experiments indicate the possibility of increasing the size of the spherulites in the gel medium展开更多
Ink-jet printing of ceramic thick films is one of low cost on-site ceramic pattern fabrication methods.It is necessary to investigate the rheological behaviour of ceramic inks and drying behaviour of droplets.Two kind...Ink-jet printing of ceramic thick films is one of low cost on-site ceramic pattern fabrication methods.It is necessary to investigate the rheological behaviour of ceramic inks and drying behaviour of droplets.Two kinds of BaTiO3 ceramic inks were prepared by mechanical mixing and sol-gel methods,respectively.The effect of preparation parameters,such as quantity of polyacrylic acid(PAA)and solid content,on physicochemical and rheologic properties of the ceramic inks was investigated.The results show that they satisfy the requirements of continuous ink-jet printing.The appearances of printed dots and single printed layers were observed by SEM.The SEM images indicate that dots printed with mixing method ink are in ring shape,and dots printed with sol-gel method ink are in pancake shape,so the printed layer surface with the latter ink is smoother.The causes of these phenomena were discussed.展开更多
Ti-Si mixed oxides with different TiO2 content were prepared by sol-gel one step hydrolysis, using TiCl4 as the precursor. The samples were characterized by BET, FT-IR and XRD. The results indicated that titanium is...Ti-Si mixed oxides with different TiO2 content were prepared by sol-gel one step hydrolysis, using TiCl4 as the precursor. The samples were characterized by BET, FT-IR and XRD. The results indicated that titanium is in fourfold coordination with oxygen in the SiO44- in mixed oxides, form the bond of Ti-O-Si, and the low titania materials are mixed on an atomic scale. The phase of anatase appeared when TiO2 content is up to 80%. The mixed oxides had high specific surface areas up to 681.5 m2/g. 10TiSi is a better support than SiO2 in the reaction of CO oxidation.展开更多
Three kinds of amphiphilic PMADAB gels were prepared through radiation-induced polymerization and crosslinking of methacryloxyethyl dimethylalkane ammonium bromide(MADAB) with different alkyl side chains(butyl,octyl a...Three kinds of amphiphilic PMADAB gels were prepared through radiation-induced polymerization and crosslinking of methacryloxyethyl dimethylalkane ammonium bromide(MADAB) with different alkyl side chains(butyl,octyl and dodecyl).The length of alkyl side chains had significant influence on swelling behavior of the PMADAB gels in alcohol/water solvent.Equilibrium swelling degree(EDS) of PMBDAB(butyl) gel in water was ca.160 and decreased with increasing alcohol content(x),whereas EDS of PMODAB(octyl)and PMDDDAB(dodecyl) gels showed a convex-upward function of x,i.e.,these two gels barely swelled in pure water and swelled with increasing x and then shrank gradually.This phenomenon was explained by the hydrophobic association of long alkyl chains and a cosolvency effect of PMADAB in alcohol and water.The swelling behavior of PMADAB gels in methanol,ethanol and isopropanol were similar,and their EDS are related with the dielectric constant of alcohol solvents.The results suggest that PMADAB gels may be potential absorbents for various kinds of alcohols.展开更多
The influence of solvent and the rate of addition of water on the characteristics of alumina-zirconia powders obtained by sol-gel method were investigated. The Al2O3-ZrO2 powders (1:1 molar ratio) were prepared using ...The influence of solvent and the rate of addition of water on the characteristics of alumina-zirconia powders obtained by sol-gel method were investigated. The Al2O3-ZrO2 powders (1:1 molar ratio) were prepared using aluminum tri-sec-butoxide and zirconium n-propoxide as precursors. Ethanol (EtOH), isopropanol (iPrOH) and isobutanol (iBuOH) were used as solvents. The Al2O3-ZrO2 powders were characterized by nitrogen physisorption (SBET), Fourier transformed infrared spectroscopy (FT-IR), thermogravimetric analysis (TGA), differential thermal analysis (DTA), X-ray diffraction (XRD) and scanning electron microscopy (SEM). Prepared oxides calcined at 700℃ showed high specific surface area (200 - 240 m2/g). Obtained results suggest that the homogeneity of the mixed oxides is favored by using a water addition rate of 0.06 and 0.10 mL/min with ethanol as solvent.展开更多
Features of the motion of gel particles in a three-phase bubble column with non-foaming and foaming gas–liquid systems,determined by using experiments of radioactive particle tracking(RPT),have been compared.The trac...Features of the motion of gel particles in a three-phase bubble column with non-foaming and foaming gas–liquid systems,determined by using experiments of radioactive particle tracking(RPT),have been compared.The tracer used is a gel particle which resembles typical immobilized biocatalyst.The tracer trajectory is analyzed to extract relevant information for design purposes.The solid velocity field,turbulence parameters,dispersion coefficients,mixing times and flow transitions are determined and compared.The presence of foam significantly affects many quantified parameters,especially within the heterogeneous flow regime.The hydrodynamic stresses are reduced in the presence of foam,especially close to the disengagement.The dispersion coefficients also decrease,and the solid mixing time is only slightly affected by the presence of foam.Gas holdup,inferred both from RPT experiments and from gamma ray scanning,is higher for foaming systems and leads to a shift in the transition gas velocity towards higher values.展开更多
文摘Experiments performed on the grwth of mixed crystals of rare earth tartrates (Y1-xSmx)2 (C4H4O6)3.zH2O (0≤x≤1) from silica gels at 35~40℃ and 25~30℃ employing single-diffusion technique. are discussed. The crystals maintain spherulitic morphology, irrespective of the value of x, concentration of upper and lower reactants, gel pH, gel age and gel temperature. Formation Of Liesegang rings in this system is a temperature dependent phenomenon. It is shown that with the increase of the value of x the system passes from Liesegangring phenomenon to singlezone phenomenon. Operative mechanism of crystallization in the higher (35~40℃) and lower temperature ranges (25~30℃) is explained. Seeded growth experiments indicate the possibility of increasing the size of the spherulites in the gel medium
基金Project(106151)supported by the Major Program of the Ministry of Education of ChinaProject(59842001)supported by the National Natural Science Foundation of China
文摘Ink-jet printing of ceramic thick films is one of low cost on-site ceramic pattern fabrication methods.It is necessary to investigate the rheological behaviour of ceramic inks and drying behaviour of droplets.Two kinds of BaTiO3 ceramic inks were prepared by mechanical mixing and sol-gel methods,respectively.The effect of preparation parameters,such as quantity of polyacrylic acid(PAA)and solid content,on physicochemical and rheologic properties of the ceramic inks was investigated.The results show that they satisfy the requirements of continuous ink-jet printing.The appearances of printed dots and single printed layers were observed by SEM.The SEM images indicate that dots printed with mixing method ink are in ring shape,and dots printed with sol-gel method ink are in pancake shape,so the printed layer surface with the latter ink is smoother.The causes of these phenomena were discussed.
文摘Ti-Si mixed oxides with different TiO2 content were prepared by sol-gel one step hydrolysis, using TiCl4 as the precursor. The samples were characterized by BET, FT-IR and XRD. The results indicated that titanium is in fourfold coordination with oxygen in the SiO44- in mixed oxides, form the bond of Ti-O-Si, and the low titania materials are mixed on an atomic scale. The phase of anatase appeared when TiO2 content is up to 80%. The mixed oxides had high specific surface areas up to 681.5 m2/g. 10TiSi is a better support than SiO2 in the reaction of CO oxidation.
基金Supported by the China Postdoctoral Science Foundation(No.2012M520164)the Fundamental Research Funds for the Central Universities(No.FRF-TP-13-008A)
文摘Three kinds of amphiphilic PMADAB gels were prepared through radiation-induced polymerization and crosslinking of methacryloxyethyl dimethylalkane ammonium bromide(MADAB) with different alkyl side chains(butyl,octyl and dodecyl).The length of alkyl side chains had significant influence on swelling behavior of the PMADAB gels in alcohol/water solvent.Equilibrium swelling degree(EDS) of PMBDAB(butyl) gel in water was ca.160 and decreased with increasing alcohol content(x),whereas EDS of PMODAB(octyl)and PMDDDAB(dodecyl) gels showed a convex-upward function of x,i.e.,these two gels barely swelled in pure water and swelled with increasing x and then shrank gradually.This phenomenon was explained by the hydrophobic association of long alkyl chains and a cosolvency effect of PMADAB in alcohol and water.The swelling behavior of PMADAB gels in methanol,ethanol and isopropanol were similar,and their EDS are related with the dielectric constant of alcohol solvents.The results suggest that PMADAB gels may be potential absorbents for various kinds of alcohols.
文摘The influence of solvent and the rate of addition of water on the characteristics of alumina-zirconia powders obtained by sol-gel method were investigated. The Al2O3-ZrO2 powders (1:1 molar ratio) were prepared using aluminum tri-sec-butoxide and zirconium n-propoxide as precursors. Ethanol (EtOH), isopropanol (iPrOH) and isobutanol (iBuOH) were used as solvents. The Al2O3-ZrO2 powders were characterized by nitrogen physisorption (SBET), Fourier transformed infrared spectroscopy (FT-IR), thermogravimetric analysis (TGA), differential thermal analysis (DTA), X-ray diffraction (XRD) and scanning electron microscopy (SEM). Prepared oxides calcined at 700℃ showed high specific surface area (200 - 240 m2/g). Obtained results suggest that the homogeneity of the mixed oxides is favored by using a water addition rate of 0.06 and 0.10 mL/min with ethanol as solvent.
基金Supported by the FONCyT(PICT2014-0704)CONICET(PIP1122015-0100902CO)Universidad de Buenos Aires(UBACyT 20020130100544BA)
文摘Features of the motion of gel particles in a three-phase bubble column with non-foaming and foaming gas–liquid systems,determined by using experiments of radioactive particle tracking(RPT),have been compared.The tracer used is a gel particle which resembles typical immobilized biocatalyst.The tracer trajectory is analyzed to extract relevant information for design purposes.The solid velocity field,turbulence parameters,dispersion coefficients,mixing times and flow transitions are determined and compared.The presence of foam significantly affects many quantified parameters,especially within the heterogeneous flow regime.The hydrodynamic stresses are reduced in the presence of foam,especially close to the disengagement.The dispersion coefficients also decrease,and the solid mixing time is only slightly affected by the presence of foam.Gas holdup,inferred both from RPT experiments and from gamma ray scanning,is higher for foaming systems and leads to a shift in the transition gas velocity towards higher values.
