Optical and electrical properties of BaSnO_(3) and In_2O_(3) mixed transparent conductive films deposited by filtered cathodic vacuum arc technique at room temperature

For the crystalline temperature of BaSnO_(3)(BTO)was above 650℃,the transparent conductive BTO-based films were always deposited above this temperature on epitaxy substrates by pulsed laser deposition or molecular beam epitaxy till now which limited there application in low temperature device process.In the article,the microstructure,optical and electrical of BTO and In_(2)O_(3) mixed transparent conductive BaInSnO_(x)(BITO)film deposited by filtered cathodic vacuum arc technique(FCVA)on glass substrate at room temperature were firstly reported.The BITO film with thickness of 300 nm had mainly In_(2)O_(3) polycrystalline phase,and minor polycrystalline BTO phase with(001),(011),(111),(002),(222)crystal faces which were first deposited at room temperature on amorphous glass.The transmittance was 70%–80%in the visible light region with linear refractive index of 1.94 and extinction coefficient of 0.004 at 550-nm wavelength.The basic optical properties included the real and imaginary parts,high frequency dielectric constants,the absorption coefficient,the Urbach energy,the indirect and direct band gaps,the oscillator and dispersion energies,the static refractive index and dielectric constant,the average oscillator wavelength,oscillator length strength,the linear and the third-order nonlinear optical susceptibilities,and the nonlinear refractive index were all calculated.The film was the n-type conductor with sheet resistance of 704.7Ω/□,resistivity of 0.02Ω⋅cm,mobility of 18.9 cm2/V⋅s,and carrier electron concentration of 1.6×10^(19) cm^(−3) at room temperature.The results suggested that the BITO film deposited by FCVA had potential application in transparent conductive films-based low temperature device process.

Preparation and Characteristics of Stearic Acid/PEDOT(PSS) Langmuir-Blodgett Films

Mixed Stearic acid and poly(3,4-ethylenedioxythiophene)/poly(4-styrenesulfonate) (PEDOT/PSS) Langmuir- Blodgett(LB) films were successfully fabricated by the conventional vertical dipping method.Stearic acid and PEDOT/PSS was dissolved in chloroform and spread on subphase containing 0.04wt% FeCl_3.Conductive Y-type mixed LB films was successfully prepared under the condition of surface pressure with 30 mN/m,pH 3.8,and 19℃.UV-VIS spectrum showed that well ordered layer-by-layer fabrication of mixed films were obtained and thickness of single layer film with about 5 nm was evaluated.The morphology image of mixed LB film was observed by atomic force microscopy (AFM).The conductivity of mixed LB film was about 1.8×10^(-5)S/cm and the film showed sensitivity to NH_3 at the same time.

Numerical investigation of unsteady mixing mechanism in plate film cooling

A large-scale large eddy simulation in high performance personal computer clusters is carried out to present unsteady mixing mechanism of film cooling and the development of films. Simulation cases include a single-hole plate with the inclined angle of 30° and blowing ratio of 0.5, and a single-row plate with hole-spacing of 1.5D and 2D （diameters of the hole）. According to the massive simulation results, some new unsteady phenomena of gas films are found. The vortex system is changed in different position with the development of film cooling with the time marching the process of a single-row plate film cooling. Due to the mutual interference effects including mutual exclusion, a certain periodic sloshing and mutual fusion, and the structures of a variety of vortices change between parallel gas films. Macroscopic flow structures and heat transfer behaviors are obtained based on 20 million grids and Reynolds number of 28600.

Acidichromism in the Mixed Langmuir-Blodgett Films of Stearic Acid with a Carbazole-containing Schiff Base

A new Schiff base containing carbazole group (CzSB) was synthesized. Although the compound can not form stable monolayer at air/water interface itself, it does form stable monolayers by mixing with stearic acids as verified from the surface pressure area measurements. The mixed monolayers can be deposited by vertical dipping method. UV Spectroscopic studies of the mixed LB films reveal a broadening and red shift of the absorption spectra compared to those of CzSB in the ethanol solution, which confirms the formation of organized aggregates of the compounds in the mixed LB films. An ordered LB film was obtained as confirmed by using low angle X ray diffraction. The mixed LB film shows acidichromism, that is, the colors of the LB films can be reversibly changed upon exposing to HCl and NH 3 gas alternatively. On the basis of FT IR measurement, it is proposed that the protontation of the imine group in the compound is the reason for the acidichromism.

An empirical method for estimating surface area of aggregates in hot mix asphalt

Bitumen requirement in hot mix asphalt （HMA） is directly dependent on the surface area of the aggregates in the mix, which in turn has effect on the asphalt film thickness and the flow characteristics. The surface area of aggregate blend in HMA is calculated using the specific surface area factors assigned to percentage passing through some specific standard sieve sizes and the imaging techniques. The first process is less capital intensive, but purely manual and labour intensive and prone to human errors. Imaging techniques though eliminating the human errors, still have limited use due to capital intensiveness and requirement of well-established ]aboratories with qualified technicians. Most of the developing countries like India are shortage of well-equipped laboratories and qualified technicians. To overcome these difficulties, the present mathematical model has been developed to estimate the surface area of aggregate blend of HMA from physical properties of aggregates evaluated using simple laboratory equipment. This model has been validated compared with the existing established methods of calculations and can be used as one of the tools in different developing and under developed countries for proper design of HMA.