MOLECULAR BEAM STUDIES ON OXIDATION OF CO ON Pd WITH DIFFERENT MIXED RATIOS OF P_(CO) TO P_(O2) ~*

Here some steady-state experiments on oxidation of CO on Pd were performed on a molecular beam apparatus. It is found that the characteristics of the rate of CO_2 formation r versus substrate temperature T are dependent on the ratio P=P_(CO)/P_(O2) in the mixed beam. These characteristics are related to the complicated interactions of co-adsorbed CO and O particles on Pd surface.

Microscopic Analysis of Cementitious Sand and Gravel Damming Materia

The mechanical properties of cementitious sand and gravel damming material have been experimentally determined by means of microscopic SEM(Scanning Electron Microscopy)image analysis.The results show that the combination of fly ash and water can fill the voids in cemented sand and gravel test blocks because of the presence of hydrated calcium silicate and other substances;thereby,the compactness and mechanical properties of these materials can be greatly improved.For every 10 kg/m^(3) increase in the amount of cementitious material,the density increases by about 2%,and the water content decreases by 0.2%.The amount of cementitious material used in the sand and gravel in these tests was 80-110 kg/m^(3),the water-binder ratio was 1-1.50.Moreover,the splitting tensile strength was 1/10 of the compressive strength,and the maximum strength was 7.42 MPa at 90 d.The optimal mix ratio has been found to be 50 kg of cement,60 kg of fly ash and 120 kg of water(C50F60W120).The related dry density was 2.6 g/cm^(3),the water content was 6%,and the water-binder ratio was 1.09.

Constraining Anthropogenic CH_4 Emissions in Nanjing and the Yangtze River Delta,China,Using Atmospheric CO_2 and CH_4 Mixing Ratios

Methane （CH4） emissions estimated with the Intergovernmental Panel on Climate Change （IPCC） inventory method at the city and regional scale are subject to large uncertainties.In this study,we determined the CH4：CO2 emissions ratio for both Nanjing and the Yangtze River Delta （YRD）,using the atmospheric CH4 and CO2 concentrations measured at a suburban site in Nanjing in the winter.The atmospheric estimate of the CH4：CO2 emissions ratio was in reasonable agreement with that calculated using the IPCC method for the YRD （within 20％）,but was 200％ greater for the municipality of Nanjing.The most likely reason for the discrepancy is that emissions from unmanaged landfills are omitted from the official statistics on garbage production.

Measurements of NO_2 mixing ratios with topographic target light scattering-differential optical absorption spectroscopy system and comparisons to point monitoring technique

A topographic target light scattering-differential optical absorption spectroscopy （＇IbTaL-DOA~） system is de- veloped for measuring average concentrations along a known optical path and studying surface-near distributions of atmospheric trace gases. The telescope of the ToTaL-DOAS system points to targets which are located at known dis- tances from the measurement device and illuminated by sunlight. Average concentrations with high spatial resolution can be retrieved by receiving sunlight reflected from the targets, A filed measurement of NO2 concentration is performed with the ToTaL-DOAS system in Shijiazhuang in the autumn of 2011. The measurement data are compared with con- centrations measured by the point monitoring technique at the same site. The results show that the ToTaL-DOAS system is sensitive to the variation of NO2 concentrations along the optical path.

Variations of CO2 Mixing Ratios in the Air near the Ground in the European Territory of Russia

The instrumentation, method and measurement results used for measurements of CO2 concentrations in surface air of Obninsk （55.1° N, 36.9° E, 183 m above the sea level） located at a distance of 105 km to the south-west of Moscow are presented. Proposed is a method of experimental data filtering allowing one to separate natural and anthropogenic variations of CO2 concentrations. It is shown that minimal concentrations of CO2 registered in Obninsk and at the continental stations of GAW WMO characterize not only the ＂regional background＂ but also coincide with the data from GAW WMO background stations located in the oceanic regions. In this connection, one can assume that the excess in measured CO2 concentration over its minimal values, making about 5-6 ppm, is connected with an anthropogenic emission, and the continent should be considered as an anthropogenic source of C02.

Determination Multipole Mixing Ratios and Transition Strengths of Gamma Rays from Level Studies of 93Mo （p, nγ） Reaction

The multipole mixing ratios have been calculated by a2-ratio method, from levels of 93Mo（p, nγ） reaction. The branching ratios of such γ-transitions are used to calculate the total gamma widths. Besides, the transition strengths and probabilities have been calculated for γ-transitions from excited states whose life times have been reported previously. The results are found to be in general in good agreement with the previous results populated from the previous work.

Equal Volumes of Sand and Gravel Concrete Mix Ratios in Cameroon and Its Effect on Concrete Compressive Strength

In recent years, the rationalization of concrete mix ratios which batches equal volumes of sand and gravel in building projects has been gaining grounds in the Cameroon construction industry. The main objective of this study is therefore to investigate if the concrete produced with rationalized mix ratio can be adopted as conventional mix ratio in terms of minimum required compression strength of concrete for buildings. Specifically this work compared the conventional mix ratio of 350 kg of cement: 400 liters of sand: 800 liters of gravel for a cubic meter and the rationalized batch of 350 kg of cement: 600 liters of sand: 600 liters of 5/15 gravel, 15/25 gravel and a combination of 5/15 + 15/25 gravel. Average compressive tests’results for both the conventional and the rationalized mix ratios were found to meet the minimum compressive strength of 65% at 7 days, 90% at 14 days and 99% at 28 days for gravel size combination 5/15 + 15/25. Single size gravel of 5/15 and 15/25 did not meet the minimum required compressive strength of 20 N/mm2 for the rationalized mix ratio at 28 days curing based on the minimum compressive strength required, this study arrives at the conclusion that the equal volumes of sand and gravel mix ratio of 350 kg/m3 of cement: 600 liters of sand: 600 liters of gravel mix ratio can be adopted as a conventional concrete mix ratio for gravel size 5/15 + 15/25.

Identification of Mixtures of Two Types of Body Fluids Using the Multiplex Methylation System and Random Forest Models

Objective Body fluid mixtures are complex biological samples that frequently occur in crime scenes,and can provide important clues for criminal case analysis.DNA methylation assay has been applied in the identification of human body fluids,and has exhibited excellent performance in predicting single-source body fluids.The present study aims to develop a methylation SNaPshot multiplex system for body fluid identification,and accurately predict the mixture samples.In addition,the value of DNA methylation in the prediction of body fluid mixtures was further explored.Methods In the present study,420 samples of body fluid mixtures and 250 samples of single body fluids were tested using an optimized multiplex methylation system.Each kind of body fluid sample presented the specific methylation profiles of the 10 markers.Results Significant differences in methylation levels were observed between the mixtures and single body fluids.For all kinds of mixtures,the Spearman’s correlation analysis revealed a significantly strong correlation between the methylation levels and component proportions(1:20,1:10,1:5,1:1,5:1,10:1 and 20:1).Two random forest classification models were trained for the prediction of mixture types and the prediction of the mixture proportion of 2 components,based on the methylation levels of 10 markers.For the mixture prediction,Model-1 presented outstanding prediction accuracy,which reached up to 99.3%in 427 training samples,and had a remarkable accuracy of 100%in 243 independent test samples.For the mixture proportion prediction,Model-2 demonstrated an excellent accuracy of 98.8%in 252 training samples,and 98.2%in 168 independent test samples.The total prediction accuracy reached 99.3%for body fluid mixtures and 98.6%for the mixture proportions.Conclusion These results indicate the excellent capability and powerful value of the multiplex methylation system in the identification of forensic body fluid mixtures.

Distribution Characteristics of Ozone and the Relationship with Typhoon Processes in the Northwest Pacific Ocean

Based on the vertical ozone reanalysis data and total ozone column data derived from the European Centre for Medium-Range Weather Forecasts,the spatial and temporal distribution characteristics of ozone on each isobaric surface in the troposphere over the Northwest Pacific Ocean were analyzed,and the backward trajectory method was used to track the influence of typhoon on the distribution of ozone.The results show that the updraft near the typhoon center transported the air with low O_(3)content in the lower layer to the upper layer,which reduced O_(3)content in the upper layer and formed a low-value area of O_(3).The variation trend of total ozone column in the regions where typhoons"Megi"and"Fengshen"occurred was analyzed by the case analysis method.It is found that there was a low-value area of total ozone column anomaly near the typhoon center,and there was a certain correlation between typhoon intensity PDI and total ozone column anomaly at the development and maturity stages of typhoons.

Effect of Starch/Polylactic Acid Ratio on the Interdependence of Two-Phase and the Properties of Composites

Starch/polylactic acid(PLA) composites were prepared by melt extrusion, with corn starch and PLA as raw materials, glycerol as the plasticizer. Effects of starch/PLA ratio on the interdependence of two-phase and other properties of the composites were studied. The combination of results of TGA with SEM indicated that the interdependence between starch and PLA was increased gradually as the starch/PLA ratio reduced. DSC results showed that the glass transition temperature(Tg), melting temperature(Tm) and degree of crystallinity of PLA in composites were increased gradually, whereas the cold crystallization temperature(Tc) was gradually decreased as the starch/PLA ratio reduced. The rheological properties of composites were closely related with the interdependence of two-phase, with reducing starch/PLA proportion, the interdependence was increased, and then the strain for storage modulus was firstl reduced and then gradually increased. Frequency scanning showed that the storage modulus and complex viscosity were decreased with reducing starch content. As the starch/PLA ratio reduced, the matrix phase PLA was increased, so that the strength of composites was increased gradually, whereas water absorption rate was decreased gradually.

Study on co-cracking performance of different hydrocarbon mixture in a steam pyrolysis furnace

Co-cracking is a process where the mixtures of different hydrocarbon feedstocks are cracked in a steam pyrolysis furnace, and widely adopted in chemical industries. In this work, the simulations of the co-cracking of ethane and propane, and LPG and naphtha mixtures have been conducted, and the software packages of COILSIM1 D and Sim CO are used to account for the cracking process in a tube reactor. The effects of the mixing ratio, coil outlet temperature, and pressure on cracking performance have been discussed in detail. The co-cracking of ethane and propane mixture leads to a lower profitability than the cracking of single ethane or single propane. For naphtha, cracking with LPG leads to a higher profitability than single cracking of naphtha, and more LPG can produce a higher profitability.

Application of TRMM/PR Data for Numerical Simulations with Mesoscale Model MM5

Numerical simulations of two heavy rainfall cases in the Changjiang-Huaihe River basin are performed with TRMM/PR (precipitation radar) data incorporated into the PSU/NCAR meso scale model MM5. The mixing ratio of rainwater q r is obtained from the R −q r relation (R is the rainfall rate), and the mixing ratio of water vapor q v in the model is replaced by q 1′v = q v+q r. Then, TRMM/PR data are used to modify humidity analysis obtained from conventional radiosonde data, and sensitivity experiments (STE) are performed and compared to control experiments (CTL). Results show that both the heavy rainfall distribution and its maximum amounts from STE are improved compared with those from CTL.

Multichannel Discharge Characteristics of Gas Switch Gap in SF_6-N_2 or SF_6-Ar Gas Mixtures Under Nanosecond Triggering Pulses

Experiments were carried out to ascertain multichannel discharge characteristics in a self-designed coaxial field-distortion gas switch filled with SFa-N2 or SF6-Ar gas mixtures of different mixing ratios. In these experiments, the pressure varied from 0.1 MPa to 0.2 MPa, the voltage pulse peak applied to the switch was in the range from 40 kV to 78 kV, and the pulse rise time was 11 ns. The static breakdown strength of the gas switch gap in the switch was also measured. The results show that in general the average number of discharge channels for SF6-Ar or SF6-N2 gas mixture which contains less SFa is larger than that for gas mixture which contains more SF6, however, the average number of channels almost keeps constant as the gas mixing ratio varies when the pulse rise rate is high enough. The static breakdown strength of the gas switch gap decreases slightly as the content of argon or nitrogen increases.

Production and Evaluation of Synthetic Carbonated Sand as an Adsorbent Media for Batch Adsorption Process

An attempt was made to improve the adsorption capability of the normal sand to be used as adsorbent for phenol and cadmium This has been done by producing a coated sand media. The coating process was done using emulsion asphalt to convert the normal sand to carbonated sand by using chemical treatment with sulfuric acid. The production process involves mixing of the sand with asphalt and an acid, then subjecting the mix to a heating process. Different mixing ratios, heating temperatures and times （activation times） were tried to obtain the optimum conditions at which the highest removal efficiency is obtained. Three types of acids were tried acetic acid, phosphoric acid and sulfuric acid. It was found that the sulfuric acid requires the lowest activation time, hence selected for the production. The removal efficiency of the produced media was significantly affected by the temperature, mixing ratio and activation heating time. The results show that, the optimum conditions for the production process are 350 , （1：2：3） （Asphalt/acid/sand） and 52 min for temperature, mixing ratio and activation heating time respectively. The final product was tested and found effective as an adsorbent media for phenol and cadmium. The removal efficiencies of these two pollutants in a batch adsorber were found 82.42% and 86.67%, respectively. The X-R diffraction and FTIR spectra tests had proved this media as an adsorbent.

Biohydrogen Production from Synthetic Waste Co-digested with Liquid Dairy Cow Manure： Effect of Temperature and Mixing Ratio

Biohydrogen production from synthetic waste, SW （model organic fraction of municipal solid waste） co-digested with liquid dairy manure （M） was tested in batch reactions to assess the effect of temperature and mixing ratio of the substrates. A 5 × 2 factorial design experiment was conducted. Synthetic waste： manure mixtures of 1：1, 2：1, 3：1, 1：0, 0：1 （volatile solids, VS, basis） were tested at 37 （T37） and 55 ℃ （T55） using thirty 1 L laboratory scale digesters. Total VS of each mixture was 50 g/L except SW：M 0：I treatment, where total VS was 27.4 g/L. Gas samples were taken daily to determine hydrogen production, and slurry samples taken before and after experimentation, were analyzed for volatile fatty acid （VFA） concentration, volatile solid （VS） degradation, ammonium nitrogen （NH4＋-N） and pH. Hydrogen production （mL/g-VS fed） showed a significant two-factor interaction between incubation temperature and SW：M ratio （P 〈 0.001）. Maximum production of 15.8 mL/g-VS （fed） was achieved in SW：M ratio of 3：1 at 55 ℃. Generally, hydrogen productions at thermophilic temperature （T55） were significantly higher than at mesophilic （T37） temperature for all treatments （P 〈 0.001） except for SW：M 1：0 and SW：M 0：1 treatments （P 〉 0.05）. This study indicates that hydrogen production from co-digestion of synthetic waste and manure is dependent on incubation temperature and relative contribution of wastes in the mixture.

Preparation and Optimization of Mix ratio for C50T Girder Manufactured Sand and Concrete

Considering actual construction conditions of Binchuan-Heqing Highway,this paper provides the C50 mix ratio conforming to engineering requirements by strictly controlling the quality of raw materials,optimizing the design of mix ratio scientifically,preparing superior C50 concrete 0 with manufactured sand,and optimizing the concrete mix ratio based on the adjustment of fly ash replacement,water-cement ratio,polycarboxylate-type water reducer mixing amount,sand ratio,etc.The result indicates that,the water-cement ratio has a great influence on the concrete strength,and if the ratio of coal ash is high in the binding material,the early compressive strength of the concrete will increase slowly.

Effects of different mixing ratios on emissions from passenger cars fueled with methanol/gasoline blends

Regulated and unregulated emissions from four passenger cars fueled with methanol/gasoline blends at different mixing ratios （M15,M20,M30,M50,M85 and M100） were tested over the New European Driving Cycle （NEDC）.Volatile organic compounds （VOCs） were sampled by Tenax TA and analyzed by thermal desorption-gas chromatograph/mass spectrometer （TD-GC/MS）.Carbonyls were trapped on dinitrophenylhydrazine （DNPH） cartridges and analyzed by high performance liquid chromatography （HPLC）.The results showed that total emissions of VOCs and BTEX （benzene,toluene,ethylbenzene,p,m,o-xylene） from all vehicles fueled with methanol/gasoline blends were lower than those from vehicles fueled with only gasoline.Compared to the baseline,the use of M85 decreased BTEX emissions by 97.4%,while the use of M15 decreased it by 19.7%.At low-to-middle mixing ratios （M15,M20,M30 and M50）,formaldehyde emissions showed a slight increase while those of high mixing ratios （M85 and M100） were three times compared with the baseline gasoline only.When the vehicles were retrofitted with new three-way catalytic converters （TWC）,emissions of carbon monoxide （CO）,total hydrocarbon （THC）,and nitrogen oxides （NOx） were decreased by 24%–50%,10%–35%,and 24%–58% respectively,compared with the cars using the original equipment manufacture （OEM） TWC.Using the new TWC,emissions of formaldehyde and BTEX were decreased,while those of other carbonyl increased.It is necessary that vehicles fueled with methanol/gasoline blends be retrofitted with a new TWC.In addition,the specific reactivity of emissions of vehicles fueled with M15 and retrofitted with the new TWC was reduced from 4.51 to 4.08 compared to the baseline vehicle.This indicates that the use of methanol/gasoline blend at a low mixing ratio may have lower effect on environment than gasoline.

A method for estimating the fraction of mineral dust in particulate matter using PM2.5-to-PM10 ratios

A simple method for estimating the contributions of mineral dust to PM2.5, PM10, or TSP is presented. The method is based on the assumption of external mixing of two types of particles with different PM2.5/PM10 ratios, The method was applied to local and transported dust events observed in Tsukuba, Japan, and was compared with collocated polarization lidar measurements. The method was then applied to three dust events that occurred in Oki, Rishiri, and Ochiishi,Japan, in 2012. The results showed that the method was useful for detecting mineral dust and for qualitatively describing the mixing of dust with anthropogenic aerosols.

Prediction Model-based Multi-objective Optimization for Mix-ratio Design of Recycled Aggregate Concrete

The prediction model for mechanical properties of RAC was established through the Bayesian optimization-based Gaussian process regression(BO-GPR)method,where the input variables in BO-GPR model depend on the mix ratio of concrete.Then the compressive strength prediction model,the material cost,and environmental factors were simultaneously considered as objectives,while a multi-objective gray wolf optimization algorithm was developed for finding the optimal mix ratio.A total of 730 RAC datasets were used for training and testing the predication model,while the optimal design method for mix ratio was verified through RAC experiments.The experimental results show that the predicted,testing,and expected compressive strengths are nearly consistent,illustrating the effectiveness of the proposed method.

Effect of different levels of corn steep liquor addition on fermentation characteristics and aerobic stability of fresh rice straw silage

The object of this study was to determine the proper mixing ratio of fresh rice straw to corn steep liquor(CSL) to obtain a high protein content silage feed. The following experimental silages were generated: the control(C1), composed of fresh rice straw without CSL additive, mixed with CSL in the ratios of 4:1(C4),3:1(C3) and 2:1(C2). Lactic acid bacteria(LAB) inoculant was applied at the rate of 50 mL/kg(fresh basis)of forage to achieve a final application rate of 1 x 10~6 cfu/g of fresh matter(FM). Duplicate silos for each treatment were opened after 0,3, 7,10,20,30,45 and 60 d for microbiological and chemical analysis. The results showed that the addition of CSL significantly increased crude protein(CP) contents, and decreased neutral detergent fiber(NDF) and acid detergent fiber(ADF) contents of treatments after 60 d of ensiling(P < 0.05). The lactic acid contents in C4 and C3 were significantly higher than that in C1(P <0.05). In summary, mixing fresh rice straw with CSL at addition levels of 4:1(C4) and 3:1(C3) can improve the fermentation quality and nutrient composition of fresh rice straw silage. However, a large proportion of CSL(C3) had a negative impact on the aerobic stability of fresh rice straw.