Gallium oxide(Ga_2O_3) thin films were deposited on a-Al2O3(1120) substrates by pulsed laser deposition(PLD) with different oxygen pressures at 650?C. By reducing the oxygen pressure, mixed-phase Ga_2O_3 films with α...Gallium oxide(Ga_2O_3) thin films were deposited on a-Al2O3(1120) substrates by pulsed laser deposition(PLD) with different oxygen pressures at 650?C. By reducing the oxygen pressure, mixed-phase Ga_2O_3 films with α and β phases can be obtained, and on the basis of this, mixed-phase Ga_2O_3 thin film solar-blind photodetectors(SBPDs) were prepared.Comparing the responsivities of the mixed-phase Ga_2O_3 SBPDs and the single β-Ga_2O_3 SBPDs at a bias voltage of 25 V,it is found that the former has a maximum responsivity of approximately 12 A/W, which is approximately two orders of magnitude larger than that of the latter. This result shows that the mixed-phase structure of Ga_2O_3 thin films can be used to prepare high-responsivity SBPDs. Moreover, the cause of this phenomenon was investigated, which will provide a feasible way to improve the responsivity of Ga_2O_3 thin film SBPDs.展开更多
Mixed-phase TiO_2 photocatalysts with small particle size of anatase and rutile(~5 nm) have been successfully synthesized using hydrothermal method. The effects of curing temperature and curing time before the hydroth...Mixed-phase TiO_2 photocatalysts with small particle size of anatase and rutile(~5 nm) have been successfully synthesized using hydrothermal method. The effects of curing temperature and curing time before the hydrothermal treatment on the crystalline phase, the phase composition, and the particle size of TiO_2 were investigated by the X-ray diffraction spectroscopy(XRD) and the transmission electron microscopy(TEM), respectively. It was found that the anatase and rutile phase contents in the TiO_2 particles were successfully controlled by simply adjusting the curing temperature and the curing time. More importantly, the particle size of both anatase and rutile is small in the mixed-phase TiO_2 particles. The photocatalytic activity of TiO_2 was evaluated by the degradation of Rhodamine B(Rh B) in aqueous solution. The Ti O2 with phase junction formed by anatase and rutile exhibited higher separation rate between the photo-induced electrons and holes, which was confirmed by the surface photovoltage(SPV) spectra, and at the same time exhibited the higher photocatalytic degradation on Rh B than pure anatase-phase TiO_2. Moreover, it was found that TiO_2 with 83% of anatase and 17% of rutile showed a highest photocatalytic activity among the mixed-phase TiO_2 samples.展开更多
To reduce the production cost of titanium,a new method for direct preparation of low-oxygen titanium powder by the magnesiothermic reduction of TiO_(2) with the assistance of a MgCl_(2)−HoCl_(3) molten salt was propos...To reduce the production cost of titanium,a new method for direct preparation of low-oxygen titanium powder by the magnesiothermic reduction of TiO_(2) with the assistance of a MgCl_(2)−HoCl_(3) molten salt was proposed.Thermodynamic calculations showed that the magnesiothermic reduction of TiO_(2) was feasible.However,hindrance of the reduction reaction by the reduction by-product of MgO resulted in a considerably high O concentration in the titanium powder.The addition of HoCl_(3) to the system significantly reduces the activity of MgO to produce low-oxygen titanium powder.Thermochemical deoxidation and reduction experiments were conducted with MgCl_(2)−HoCl_(3) molten salt in the temperature range of 1023−1273 K.The results showed that titanium powder with oxygen concentration(mass fraction)below 5.00×10^(-4) can be prepared at the Mg−MgCl_(2)−HoOCl−HoCl_(3) equilibrium.展开更多
This study used a Polyindole in combination with TiO2 nanocatalyst as an efficient heterogeneous catalyst to carry out a multi-component Hantzsch reaction involving different aromatic aldehydes with methyl acetoacetat...This study used a Polyindole in combination with TiO2 nanocatalyst as an efficient heterogeneous catalyst to carry out a multi-component Hantzsch reaction involving different aromatic aldehydes with methyl acetoacetate, and aqueous ammonium to create 1,4-dihydropyridine derivatives under solvent free condition at ambient temperature. A broad range of aldehydes and methyl acetoacetates, ranging from heteroaromatic to polyaromatic one, with high level of functional group tolerance can be used to provide the desired products possessing relevant medicinal moiety in high yields. This technology has prospective advantages over current protocols, including the utilization of a cheap, stable, recyclable, and safe catalyst, quicker reaction times with higher yields and simple product isolation.展开更多
The simulation by the Monte Carlo method executed by the software PyPENELOPE proved effective to specify the particle propagation characteristics by calculating the absorption fractions, backscattering and transmissio...The simulation by the Monte Carlo method executed by the software PyPENELOPE proved effective to specify the particle propagation characteristics by calculating the absorption fractions, backscattering and transmission of electrons and secondary photons under the incidence of 0.5 to 20 KeV range of primary electrons. More than 99.9% of the primary electrons were transmitted in the 125 nm thick MgO/TiO<sub>2</sub> material at 20 KeV. This occurred because several interactions took place in the transmitted primary irradiation such as characteristic, fluorescence, and bremsstrahlung produced when of the occupation of the KL3, KL2, KM3, and KM2 shell and sub-shell of titanium and magnesium which are the elements with a high atomic number in the material. The transmission particle characteristic of this material is therefore an indicator capable of improving the electrical performance and properties of the sensor.展开更多
This study focused on the development and characterization of TiO<sub>2</sub>-PES composite fibers with varying TiO<sub>2</sub> loading amounts using a phase inversion process. The resulting co...This study focused on the development and characterization of TiO<sub>2</sub>-PES composite fibers with varying TiO<sub>2</sub> loading amounts using a phase inversion process. The resulting composite fibers exhibited a sponge-like structure with embedded TiO<sub>2</sub> nanoparticles within a polymer matrix. Their photocatalytic performance for ammonia removal from aqueous solutions under UV-A light exposure was thoroughly investigated. The findings revealed that PeTi8 composite fibers displayed superior adsorption capacity compared to other samples. Moreover, the study explored the impact of pH, light intensity, and catalyst dosage on the photocatalytic degradation of ammonia. Adsorption equilibrium isotherms closely followed the Langmuir model, with the results indicating a correlation between qm values of 2.49 mg/g and the porous structure of the adsorbents. The research underscored the efficacy of TiO<sub>2</sub> composite fibers in the photocatalytic removal of aqueous under UV-A light. Notably, increasing the distance between the photocatalyst and the light source resulted in de-creased hydroxyl radical concentration, influencing photocatalytic efficiency. These findings contribute to our understanding of TiO<sub>2</sub> composite fibers as promising photocatalysts for ammonia removal in water treatment applications.展开更多
We prepared TiO 2(anatase) and Sn doped TiO 2 nanoparticlate film by Plasma enhanced Chemical Vapor Deposition(PECVD) method. XRD and XPS experiments showed that Sn was doped into the lattice of TiO 2 with a ratio of ...We prepared TiO 2(anatase) and Sn doped TiO 2 nanoparticlate film by Plasma enhanced Chemical Vapor Deposition(PECVD) method. XRD and XPS experiments showed that Sn was doped into the lattice of TiO 2 with a ratio of n (Sn)∶ n (Ti)=1∶10 . Sn doping largely enhanced the photocatalytic activity of TiO 2 film for phenol degradation. The enhancement in photoactivity by doping was discussed, based on the characterization with AFM, FTIR and EFISPS. Sn doping produced localized level of Sn 4+ in the band gap of TiO 2, about 0.4 eV below the conduction band, which could capture photogenerated electrons and reduce O 2 adsorbed on the surface of TiO 2 film, thus accelerated the photocatalytic reaction.展开更多
The transition metal ion doped TiO 2 nanoparticles were prepared with hydrothermal method, and the effects of doping different metal ions on the ability of TiO 2 in photocatalyzing degradation of rhodamine B(RB) were ...The transition metal ion doped TiO 2 nanoparticles were prepared with hydrothermal method, and the effects of doping different metal ions on the ability of TiO 2 in photocatalyzing degradation of rhodamine B(RB) were studied. The results showed that the doping of Fe 3+ , Co 2+ , Ni 2+ and Cr 3+ in TiO 2 nanoparticles made the photocatalytic efficiency of the TiO 2 particles reduce and the higher the initial content of Fe 3+ , the lower the ability of TiO 2 in photocatalyzing the degradation of RB. But the doping of Zn 2+ and Cd 2+ , especially Zn 2+ , made the photocatalytic efficiency of the TiO 2 particles enhance, showing a great increase of the rate constant( k ) and the initial reaction rate( r ini ).展开更多
基金Project supported by the National Natural Science Foundation of China(Grant Nos.51872187,51302174,11774241,and 61704111)the National Key Research and Development Program of China(Grant No.2017YFB0400304)+3 种基金the Natural Science Foundation of Guangdong Province,China(Grant Nos.2016A030313060 and 2017A030310524)the Project of Department of Education of Guangdong Province,China(Grant No.2014KTSCX110)the Fundamental Research Project of Shenzhen,China(Grant No.JCYJ20180206162132006)the Science and Technology Foundation of Shenzhen,China(Grant No.JCYJ2015-2018)
文摘Gallium oxide(Ga_2O_3) thin films were deposited on a-Al2O3(1120) substrates by pulsed laser deposition(PLD) with different oxygen pressures at 650?C. By reducing the oxygen pressure, mixed-phase Ga_2O_3 films with α and β phases can be obtained, and on the basis of this, mixed-phase Ga_2O_3 thin film solar-blind photodetectors(SBPDs) were prepared.Comparing the responsivities of the mixed-phase Ga_2O_3 SBPDs and the single β-Ga_2O_3 SBPDs at a bias voltage of 25 V,it is found that the former has a maximum responsivity of approximately 12 A/W, which is approximately two orders of magnitude larger than that of the latter. This result shows that the mixed-phase structure of Ga_2O_3 thin films can be used to prepare high-responsivity SBPDs. Moreover, the cause of this phenomenon was investigated, which will provide a feasible way to improve the responsivity of Ga_2O_3 thin film SBPDs.
基金supported by the National Natural Science Foundation of China (21573101)the Liaoning Provincial Natural Science Foundation (2014020107)+5 种基金the Program for Liaoning Excellent Talents in University (LJQ2014041)the Support Plan for Distinguished Professors of Liaoning Province ([2015]153)the Liaoning BaiQianWan Talents Program ([2017]96)the fund of the State Key Laboratory of Catalysis in DICP (N-15-10)the Talent Scientific Research Fund of LSHU (2016XJJ-012)the University Innovation Talent Support Plan of Liaoning Province (LR2017011)
文摘Mixed-phase TiO_2 photocatalysts with small particle size of anatase and rutile(~5 nm) have been successfully synthesized using hydrothermal method. The effects of curing temperature and curing time before the hydrothermal treatment on the crystalline phase, the phase composition, and the particle size of TiO_2 were investigated by the X-ray diffraction spectroscopy(XRD) and the transmission electron microscopy(TEM), respectively. It was found that the anatase and rutile phase contents in the TiO_2 particles were successfully controlled by simply adjusting the curing temperature and the curing time. More importantly, the particle size of both anatase and rutile is small in the mixed-phase TiO_2 particles. The photocatalytic activity of TiO_2 was evaluated by the degradation of Rhodamine B(Rh B) in aqueous solution. The Ti O2 with phase junction formed by anatase and rutile exhibited higher separation rate between the photo-induced electrons and holes, which was confirmed by the surface photovoltage(SPV) spectra, and at the same time exhibited the higher photocatalytic degradation on Rh B than pure anatase-phase TiO_2. Moreover, it was found that TiO_2 with 83% of anatase and 17% of rutile showed a highest photocatalytic activity among the mixed-phase TiO_2 samples.
基金financially supported by the National Natural Science Foundation of China (No.21968013)。
文摘To reduce the production cost of titanium,a new method for direct preparation of low-oxygen titanium powder by the magnesiothermic reduction of TiO_(2) with the assistance of a MgCl_(2)−HoCl_(3) molten salt was proposed.Thermodynamic calculations showed that the magnesiothermic reduction of TiO_(2) was feasible.However,hindrance of the reduction reaction by the reduction by-product of MgO resulted in a considerably high O concentration in the titanium powder.The addition of HoCl_(3) to the system significantly reduces the activity of MgO to produce low-oxygen titanium powder.Thermochemical deoxidation and reduction experiments were conducted with MgCl_(2)−HoCl_(3) molten salt in the temperature range of 1023−1273 K.The results showed that titanium powder with oxygen concentration(mass fraction)below 5.00×10^(-4) can be prepared at the Mg−MgCl_(2)−HoOCl−HoCl_(3) equilibrium.
文摘This study used a Polyindole in combination with TiO2 nanocatalyst as an efficient heterogeneous catalyst to carry out a multi-component Hantzsch reaction involving different aromatic aldehydes with methyl acetoacetate, and aqueous ammonium to create 1,4-dihydropyridine derivatives under solvent free condition at ambient temperature. A broad range of aldehydes and methyl acetoacetates, ranging from heteroaromatic to polyaromatic one, with high level of functional group tolerance can be used to provide the desired products possessing relevant medicinal moiety in high yields. This technology has prospective advantages over current protocols, including the utilization of a cheap, stable, recyclable, and safe catalyst, quicker reaction times with higher yields and simple product isolation.
文摘The simulation by the Monte Carlo method executed by the software PyPENELOPE proved effective to specify the particle propagation characteristics by calculating the absorption fractions, backscattering and transmission of electrons and secondary photons under the incidence of 0.5 to 20 KeV range of primary electrons. More than 99.9% of the primary electrons were transmitted in the 125 nm thick MgO/TiO<sub>2</sub> material at 20 KeV. This occurred because several interactions took place in the transmitted primary irradiation such as characteristic, fluorescence, and bremsstrahlung produced when of the occupation of the KL3, KL2, KM3, and KM2 shell and sub-shell of titanium and magnesium which are the elements with a high atomic number in the material. The transmission particle characteristic of this material is therefore an indicator capable of improving the electrical performance and properties of the sensor.
文摘This study focused on the development and characterization of TiO<sub>2</sub>-PES composite fibers with varying TiO<sub>2</sub> loading amounts using a phase inversion process. The resulting composite fibers exhibited a sponge-like structure with embedded TiO<sub>2</sub> nanoparticles within a polymer matrix. Their photocatalytic performance for ammonia removal from aqueous solutions under UV-A light exposure was thoroughly investigated. The findings revealed that PeTi8 composite fibers displayed superior adsorption capacity compared to other samples. Moreover, the study explored the impact of pH, light intensity, and catalyst dosage on the photocatalytic degradation of ammonia. Adsorption equilibrium isotherms closely followed the Langmuir model, with the results indicating a correlation between qm values of 2.49 mg/g and the porous structure of the adsorbents. The research underscored the efficacy of TiO<sub>2</sub> composite fibers in the photocatalytic removal of aqueous under UV-A light. Notably, increasing the distance between the photocatalyst and the light source resulted in de-creased hydroxyl radical concentration, influencing photocatalytic efficiency. These findings contribute to our understanding of TiO<sub>2</sub> composite fibers as promising photocatalysts for ammonia removal in water treatment applications.
文摘We prepared TiO 2(anatase) and Sn doped TiO 2 nanoparticlate film by Plasma enhanced Chemical Vapor Deposition(PECVD) method. XRD and XPS experiments showed that Sn was doped into the lattice of TiO 2 with a ratio of n (Sn)∶ n (Ti)=1∶10 . Sn doping largely enhanced the photocatalytic activity of TiO 2 film for phenol degradation. The enhancement in photoactivity by doping was discussed, based on the characterization with AFM, FTIR and EFISPS. Sn doping produced localized level of Sn 4+ in the band gap of TiO 2, about 0.4 eV below the conduction band, which could capture photogenerated electrons and reduce O 2 adsorbed on the surface of TiO 2 film, thus accelerated the photocatalytic reaction.
文摘The transition metal ion doped TiO 2 nanoparticles were prepared with hydrothermal method, and the effects of doping different metal ions on the ability of TiO 2 in photocatalyzing degradation of rhodamine B(RB) were studied. The results showed that the doping of Fe 3+ , Co 2+ , Ni 2+ and Cr 3+ in TiO 2 nanoparticles made the photocatalytic efficiency of the TiO 2 particles reduce and the higher the initial content of Fe 3+ , the lower the ability of TiO 2 in photocatalyzing the degradation of RB. But the doping of Zn 2+ and Cd 2+ , especially Zn 2+ , made the photocatalytic efficiency of the TiO 2 particles enhance, showing a great increase of the rate constant( k ) and the initial reaction rate( r ini ).
