Modal analysis of the torque converter in different prestress

In order to study the mechanical properties and the dynamic performance of torque converter,to reduce the vibration and noise during the operation and to improve the stability,a 215 mm hydraulic torque converter is taken as the research object,and modal analyses are performed based on the finite element method.The weak parts of the impeller structure are obtained after calculating the models of the impeller and turbine without prestress.The variation of the modal frequency of the turbine and impeller are obtained under different prestress conditions by calculating different rotational speeds of the transmission shaft.The fundamental frequencies of the impeller and the turbine increase by 0.43%and 4.82%respectively when the rotational speed ranges from 100 rpm to 4500 rpm.The results of the present research indicate that the modal frequencies at different speeds are similar to the fundamental frequencies of the structure.Therefore,it is possible to estimate the vibration characteristics of the structure and optimize the structural design by numerical modal analysis in the static state instead of the dynamic state.

A Multilevel Hierarchical Parallel Algorithm for Large-Scale Finite Element Modal Analysis

The strict and high-standard requirements for the safety and stability ofmajor engineering systems make it a tough challenge for large-scale finite element modal analysis.At the same time,realizing the systematic analysis of the entire large structure of these engineering systems is extremely meaningful in practice.This article proposes a multilevel hierarchical parallel algorithm for large-scale finite element modal analysis to reduce the parallel computational efficiency loss when using heterogeneous multicore distributed storage computers in solving large-scale finite element modal analysis.Based on two-level partitioning and four-transformation strategies,the proposed algorithm not only improves the memory access rate through the sparsely distributed storage of a large amount of data but also reduces the solution time by reducing the scale of the generalized characteristic equation(GCEs).Moreover,a multilevel hierarchical parallelization approach is introduced during the computational procedure to enable the separation of the communication of inter-nodes,intra-nodes,heterogeneous core groups(HCGs),and inside HCGs through mapping computing tasks to various hardware layers.This method can efficiently achieve load balancing at different layers and significantly improve the communication rate through hierarchical communication.Therefore,it can enhance the efficiency of parallel computing of large-scale finite element modal analysis by fully exploiting the architecture characteristics of heterogeneous multicore clusters.Finally,typical numerical experiments were used to validate the correctness and efficiency of the proposedmethod.Then a parallel modal analysis example of the cross-river tunnel with over ten million degrees of freedom(DOFs)was performed,and ten-thousand core processors were applied to verify the feasibility of the algorithm.

Study of Axial Vibration of a Motor-Compressor System Using Operational Modal Analysis

A case study of excessive vibration on a motor-compressor system is presented in this paper.After barely two months of operation,the reciprocating compressor motor’s routine monitoring revealed excessive axial vibration amplitude.For this reason,the Operational Modal Analysis(OMA)was carried out in order to identify the pri-mary cause.According to the investigation,one of the harmonic components which was 18 times the motor’s running speed matched with a resonance frequency of 112 Hz.According to OMA study,the motor was vibrating in torsional motion because the compressor’s load had stimulated the entire motor-compressor unit at this reso-nance frequency.The analysis also demonstrates the bulging effect of the motor shaft’s axial vibration on the motor’s endplate.

Finite element failure analysis of continuous prestressed concrete box girders

In order to analyze the load carrying capacity of prestressed concrete box girders, failure behaviors of in-situ deteriorated continuous prestressed concrete box girders under loading are experimentally observed and a finite failure analysis method for predicting behaviors of box girders is developed. A degenerated solid shell element is used to simulate box girders and material nonlinearity is considered. Since pre-stressed concrete box girders usually have a large number of curve prestressed tendons, a type of combined element is presented to simulate the prestressed tendons of box girders, and then the number of elements can be significantly reduced. The analytical results are compared with full-scale failure test results. The comparison shows that the presented method can be effectively applied to the failure analysis of in-situ continuous prestressed concrete box girders, and it also shows that the studied old bridge still has enough load carrying capacity.

An operational modal analysis method in frequency and spatial domain

A frequency and spatial domain decomposition method （FSDD） for operational modal analysis （OMA） is presented in this paper, which is an extension of the complex mode indicator function （CMIF） method for experimental modal analysis （EMA）. The theoretical background of the FSDD method is clarified, Singular value decomposition is adopted to separate the signal space from the noise space. Finally, an enhanced power spectrum density （PSD） is proposed to obtain more accurate modal parameters by curve fitting in the frequency domain. Moreover, a simulation case and an application case are used to validate this method.

Effects of Joint Controller on Analytical Modal Analysis of Rotational Flexible Manipulator

Modal analysis is a fundamental and important task for modeling and control of the flexible manipulator. However, almost all of the traditional modal analysis methods view the flexible manipulator as a pure mechanical structure and neglect feedback action of joint controller. In order to study the effects of joint controller on the modal analysis of rotational flexible manipulator, a closed-loop analytical modal analysis method is proposed. Firstly, two exact boundary constraints, namely servo feedback constraint and bending moment constraint, are derived to solve the vibration partial differential equation. It is found that the stiffness and damping gains of joint controller are both included in the boundary conditions, which lead to an unconventional secular term. Secondly, analytical algorithm based on Ritz approach is developed by using Laplace transform and complex modal approach to obtain the natural frequencies and mode shapes. And then, the numerical simulations are performed and the computational results show that joint controller has pronounced influence on the modal parameters： joint controller stiffness reduces the natural frequency, while joint controller damping makes the shape phase non-zero. Furthermore, the validity of the presented conclusion is confirmed through experimental studies. These findings are expected to improve the performance of dynamics simulation systems and model-based controllers.

Theoretical analysis of natural frequency of externally prestressed concrete beam based on rigidity correction

A dynamic test on externally prestressed simply supported concrete beams separately with three typical types of tendon distributions was conducted. The results show that the natural frequencies of the beams increase with the increase in the prestressing force at the tensioning stage, and the natural frequencies decrease after the cracks occur in the beams. Following the calculation formula of natural frequency of externally prestressed beam, which was reported in a literature, the natural frequencies of the experimental beams are calculated, and big errors are found between the test results and the calculated ones of natural frequency values. As a result, this paper has tried to adopt two methods to correct the rigidity parameter of the concrete beam in the formula for natural frequency calculation, and to use the corrected formula to calculate the frequencies of the experimental beams. The calculation results indicate a good consistency with the experimental ones, which verifies the feasibility of the corrected formula.

CALCULATING RESPONSE SPECTRAL MOMENTS BY COMPLEX MODAL ANALYSIS

Response spectral moments are useful for system reliability analysis.Usually,spectral mo- ments are calculated by the frequency domain method.Based on the time domain modal analysis of random vibrations,the authors present a new method for calculating response spectral moments through response correlation functions.The method can be applied to both classical and non-classical damping cases and to three kinds of random excitations,i.e.,white noise,band-limited white noise, and filtered white noise.

Finite Element Modeling and Modal Analysis of Complicated Structure with Bolted Joints

A contact bolt model is proposed as a new modeling technique to investigate the complex structure with bolted joints for modal analysis and compared with the coupled bolt model, and the test results are given. Among these models, the coupled bolt model provides the best accurate responses compared with the experimental results. The contact bolt model shows the best effectiveness and usefulness in view of operational time. The bolt models proposed in this study are adopted for a dynamic characteristic analysis of a large diesel engine consisting of several parts which are connected by many bolts. The dynamic behavior of the entire engine structure was investigated by experiment. The coupled bolt model and the contact bolt model were applied to model the assembly of engine with high preload. The experimental results are in good agreement with the finite element method （FEM） results. Compared with the other models, the contact bolt model presented in this paper is more effective and useful in view of operational time and experience of analysts.

Modal analysis on transverse vibration of axially moving roller chain coupled with lumped mass

The modal characteristics of the transverse vibration of an axially moving roller chain coupled with lumped mass were analyzed.The chain system was modeled by using the multi-body dynamics theory and the governing equations were derived by means of Lagrange's equations.The effects of the parameters,such as the axially moving velocity of the chain,the tension force,the weight of lumped mass and its time-variable assign position in chain span,on the modal characteristics of transverse vibration for roller chain were investigated.The numerical examples were given.It is found that the natural frequencies and the corresponding mode shapes of the transverse vibration for roller chain coupled with lumped mass change significantly when the variations of above parameters are considered.With the movement of the chain strand,the natural frequencies present a fluctuating phenomenon,which is different from the uniform chain.The higher the order of mode is,the greater the fluctuating magnitude and frequency are.

Modal analysis of coupled vibration of belt drive systems

The modal method is applied to analyze coupled vibration of belt drive systems. A belt drive system is a hybrid system consisting of continuous belts modeled as strings as well as discrete pulleys and a tensioner arm. The characteristic equation of the system is derived from the governing equation. Numerical results demenstrate the effects of the transport speed and the initial tension on natural frequencies.

Aseismic safety analysis of a prestressed concrete containment vessel for CPR1000 nuclear power plant

Abstract： The containment vessel of a nuclear power plant is the last barrier to prevent nuclear reactor radiation. Aseismic safety analysis is the key to appropriate containment vessel design. A prestressed concrete containment vessel （PCCV） model with a semi-infinite elastic foundation and practical arrangement of tendons has been established to analyze the aseismic ability of the CPR1000 PCCV structure under seismic loads and internal pressure. A method to model the prestressing tendon and its interaction with concrete was proposed and the axial force of the prestressing tendons showed that the simulation was reasonable and accurate. The numerical results show that for the concrete structure, the location of the cylinder wall bottom around the equipment hatch and near the ring beam are critical locations with large principal stress. The concrete cracks occurred at the bottom of the PCCV cylinder wall under the peak earthquake motion of 0.50 g, however the PCCV was still basically in an elastic state. Furthermore, the concrete cracks occurred around the equipment hatch under the design internal pressure of 0.4MPa, but the steel liner was still in the elastic stage and its leak-proof function soundness was verified. The results provide the basis for analysis and design of containment vessels.

Modal Analysis of Thread off Failure of Oil Round Thread Casing Connection

The dynamic modal model analysis of the oil casing connection is done by finite element method (FEM), and the first nature frequency, the second nature frequency, the vibration mode shape and the time domain of the node displacement and the element stress variation in the thread connection are gotten. The Von.Mises stresses of the connection in the static and dynamic state are also studied. The results of calculation and analysis show: (1) because the maximum of static stress is at the coupling thread end of connection, the connection begins to thread off at the coupling thread end, which is in accord with the results of the thread off experiment in laboratory; (2) because the first nature frequency is very high, the probability of casing connection to be damaged from vibration is little; (3) the shock dynamic load makes casing connection begin to thread off at the tube thread end.

Uncertain Modal Analysis of Unmanned Aircraft Composite Landing Gear

Through taking uncertain mechanical parameters of composites into consideration,this paper carries out uncertain modal analysis for an unmanned aircraft landing gear.By describing correlated multi-dimensional mechanical parameters as a convex polyhedral model,the modal analysis problem of a composite landing gear is transferred into a linear fractional programming(LFR)eigenvalue solution problem.As a consequent,the extreme-point algorithm is proposed to estimate lower and upper bounds of eigenvalues,namely the exact results of eigenvalues can be easily obtained at the extreme-point locations of the convex polyhedral model.The simulation results show that the proposed model and algorithm can play an important role in the eigenvalue solution problem and possess valuable engineering significance.It will be a powerful and effective tool for further vibration analysis for the landing gear.

Application of experimental modal analysis technique to structural design of linear vibrating screen

A large model of the screen was mounted in the laboratory for studying its modal performance. The model is suspended with steel ropes. Modal test was carried out with artificially exciting by 500 g impacting hammer and 100 kg exciting force shaker respectively. Synthesis and correction of the modal parameters are obtained from both testing methods. Design faults of vibrating screen were determined based on the analy-sis and dynamic correction of structure approaches about the screen was put forward finally.

Three-dimensional Analysis of Prestressed Concrete Offshore Wind Turbine Structure Under Environmental and 5-MW Turbine Loads

A concrete gravity base structure may not be suitable for offshore weak soil because of its heavy weight. Therefore, a conceptual model for a concrete offshore wind turbine structure suitable for weak soils is proposed. The proposed model is composed of a prestressed concrete(PSC) supported by a pile foundation. For a three-dimensional analysis of the large concrete structure, wave pressures based on the diffraction wave theory are developed using a three-dimensional solid finite element method. Static and dynamic analyses were performed to achieve the conceptual model of a PSC structure subjected to ocean environmental loads and a 5-MW turbine load on southwest coast in Korea. From the analysis, the maximum displacement and stresses of the proposed model did not exceed the allowable values from design standard, and the first mode of natural frequency of the structure was in a safe range to avoid resonance. The proposed model has enough structural stability to withstand external loads, and it is expected to be used in locations suitable for concrete gravity structures.

OPERATIONAL MODAL ANALYSIS SCHEMES USING CORRELATION TECHNIQUE

For some large-scale engineering structures in operating conditions, modal param- eters estimation must base itself on response-only data. This problem has received a considerable amount of attention in the past few years. It is well known that the cross-correlation function between the measured responses is a sum of complex exponential functions of the same form as the impulse response function of the original system. So this paper presents a time-domain operating modal identifcation global scheme and a frequency-domain scheme from output-only by cou- pling the cross-correlation function with conventional modal parameter estimation. The outlined techniques are applied to an airplane model to estimate modal parameters from response-only data.

Seismic Analysis for Rigid-Framed Prestressed Reinforced Concrete Bridge in Tianjin Light Railway

The seismic analysis of a rigid-framed prestressed concrete bridge in Tianjin Light Railway is performed. A 3-D dynamic finite element model of the bridge is established considering the weakening effect caused by the soft soil foundation. After the dynamic characteristics are calculated in terms of natural frequencies and modes, the seismic analysis is carried out using the modal response spectrum method and the time-history method, respectively. Based on the calculated results, the reasonable design values are finally suggested as the basis of the seismic design of the bridge, and meanwhile the problems encountered were also analyzed. Finally, some conclusions are drawn as: 1) Despite the superiority of rigid-framed prestressed concrete bridge, the upper and lower ends of the piers of the bridge are proved to be the crucial parts of the bridge, which are easily destroyed under designed earthquake excitations and should be carefully analyzed and designed; 2) The soft soil foundation can possibly result in rather weakening of the lateral rigidity of the rigid-framed bridge, and should be paid considerable attention; 3) The modal response spectrum method, combined with time-history method, is suggested for the seismic analysis in engineering design of the rigid-framed prestressed concrete bridge.

Vibration measurement and modal analysis for tunneller

In this paper, the method of vibration measurement and modal analysis for AM50 Tunneller machine is presented. When the machine was used for cutting man made coal bed and real coal bed, the vibration of the machine was measured and the results of signal analysis show that the vibration characteristics under the two kinds of working situations are similar. The modal model of the machine is established, and then, the intrinsic vibration characteristics of AM50 tunneller are investigated by means of the method of experimental modal analysis. The vibration response simulation under a set of loading spectra measured is carried out by force response simulation software.

Simulation and modal analysis of the uplift device of a sugarcane harvester using virtual prototype technology

A three-dimensional model of the uplift device of a sugarcane harvester was built up in Pro/Engineer. Simulation and evaluation of its motional and dynamic performance were performed with the automatic dynamic analysis of mechanical system (ADAMS). ANSYS program was applied to the structural analysis of the model. A finite element analytic model was built up with the bottom-up methodology and was meshed. The default Block Lanczos method was used to work out the native frequency. The results indicate that the five lower modes-the transpotaion wheel, the left holding device, the right holding device, the left cutter disk, and the right cutter disk- and displacement of vibratory type only slightly affect the process of sugarcane harvester and harvesting quality. So it is advisable that the optimization of the static intensity other than the dynamic stiffness of uplift device be executed.