Optimization-based mode selection scheme for OAM millimeter wave system in the off-axis misalignment case

Millimeter-wave transmission combined with Orbital Angular Momentum(OAM)has the advantage of reducing the loss of beam power and increasing the system capacity.However,to fulfill this advantage,the antennas at the transmitter and receiver must be parallel and coaxial;otherwise,the accuracy of mode detection at the receiver can be seriously influenced.In this paper,we design an OAM millimeter-wave communication system for overcoming the above limitation.Specifically,the first contribution is that the power distribution between different OAM modes and the capacity of the system with different mode sets are analytically derived for performance analysis.The second contribution lies in that a novel mode selection scheme is proposed to reduce the total interference between different modes.Numerical results show that system performance is less affected by the offset when the mode set with smaller modes or larger intervals is selected.

Anti-symmetric sampled grating quantum cascade laser for mode selection

For mode selection in a quantum cascade laser(QCL),we demonstrate an anti-symmetric sampled grating(ASG).The wavelength of the-1-th mode of this laser has been blue-shifted more than 75 nm(~10 cm^(-1))compared with that of an ordinary sampled grating laser with an emission wavelength of approximately 8.6μm,when the periodicities within both the base grating and the sample grating are kept constant.Under this condition,an improvement in the continuous tuning capability of the QCL array is ensured.The ASG structure is fabricated in holographic exposure and optical photolithography,thereby enhancing its flexibility,repeatability,and cost-effectiveness.The wavelength modulation capability of the two channels of the grating is insensitive to the variations in channel size,assuming that the overall waveguide width remains constant.The output wavelength can be tailored freely within a certain range by adjusting the width of the ridge and the material of the cladding layer.

Mode Selection and Resource Allocation for Deviceto-Device Communications in 5G Cellular Networks

To meet the increasing demand of wireless broadband applications in future 5G cellular networks, Device-to-Device(D2D) communications serve as a candidate paradigm to improve spectrum efficiency. Considering the challenges after D2 D transmission is introduced for future cellular networks, this paper deals with mode selection and resource allocation issues related with D2 D communications. First, we propose a mode selection scheme which aims at guaranteeing the transmission of cellular users and also considering the potential interference. We analyze the condition under which D2 D underlay mode should be used. Second, we answer the question of "how to effectively reuse cellular resource once underlaying mode is adopted". We further present a resource allocation scheme that focuses on minimizing overall interference as well as a power control method to improve the performance of D2 D systems. Simulation results demonstrate that system parameters greatly affect the switching condition of mode selection and probability of choosing underlay mode. Furthermore, for D2 D underlaying scenario, the proposed resource allocation algorithm guarantees the transmission of cellular users with consideration of transmission requirements of D2 D users. Hence, the proposed scheme can achieve better user experience.

Joint Power Allocation and Mode Selection for D2D Communications with Imperfect CSI

Device-to-device(D2D) communications can be underlaid with a cellular infrastructure to increase resource utilization, improve user throughput and save battery energy. In such networks, power allocation and mode selection are crucial problems. To address the joint optimization of power and mode selection under imperfect CSI, we propose an optimal, energy-aware joint power allocation and mode selection(JPAMS) scheme. First, we derive the closed-form solution for the power minimization for both D2 D and cellular links while satisfying different quality of service(Qo S) constraints. Second, we address the mode selection problem in presence of imperfect CSI, based on the derived power allocation. Moreover, the theoretical analysis and simulation results are presented to evaluate the proposed scheme for the D2 D communications.

Social-Aware Joint Mode Selection and Link Allocation for Device-to-Device Communication Underlaying Cellular Networks

Joint mode selection and link allocation are crucial to achieve the advantage of Device-to-Device(D2 D) communications in improving spectral efficiency. In practice, cellular users tend to not be totally altruistic or absolutely selfish. How to stimulate them to devote their links and how to allocate their links to D2 D pair candidates efficiently are two main challenges. In this paper, we encourage cellular users through the variable payment with regard to the social tie strength between cellular users and D2 D pair candidates. In particular, the social tie strength is inferred through a graph inference model and its impact on the payment is quantified as a negative exponential function. Then, we propose a resource scheduling optimization model based on the non-transferable utility coalition formation game, and a distributed coalition formation algorithm based on the Pareto preference and merge-and-split rule. From them, the final coalition structure is obtained, which reflects the strategy of mode selection and link allocation. Numerical results are presented to verify the effectiveness of our proposed scheme.

Power allocation and mode selection methods for cooperative communication in the rectangular tunnel

For the multipath fading on electromagnetic waves of wireless communication in the confined areas,the rectangular tunnel cooperative communication system was established based on the multimode channel model and the channel capacity formula derivation was obtained.On the optimal criterion of the channel capacity,the power allocation methods of both amplifying and forwarding(AF) and decoding and forwarding(DF) cooperative communication systems were proposed in the limitation of the total power to maximize the channel capacity.The mode selection methods of single input single output(SISO) and single input multiple output(SIMO) models in the rectangular tunnel,through which the higher channel capacity can be obtained,were put forward as well.The theoretical analysis and simulation comparison show that,channel capacity of the wireless communication system in the rectangular tunnel can be effectively enhanced through the cooperative technology;channel capacity of the rectangular tunnel under complicated conditions is maximized through the proposed power allocation methods,and the optimal cooperative mode of the channel capacity can be chosen according to the cooperative mode selection methods given in the paper.

Research on Selection of Equipment Maintenance Modes

The development of equipment maintenance management is introduced, and equipment maintenance concept is defined. Equipment maintenance modes are classified, analyzed and compared, which merits and demerits are pointed out. At last, a decision-making frame to select equipment maintenance modes is advanced, and steps to select and implement equipment maintenance are given.

A SEMI-OPEN-LOOP CODING MODE SELECTION ALGORITHM BASED ON EFM AND SELECTED AMR-WB+ FEATURES

To solve the problems of the AMR-WB+(Extended Adaptive Multi-Rate-WideBand) semi-open-loop coding mode selection algorithm,features for ACELP(Algebraic Code Excited Linear Prediction) and TCX(Transform Coded eXcitation) classification are investigated.11 classifying features in the AMR-WB+ codec are selected and 2 novel classifying features,i.e.,EFM(Energy Flatness Measurement) and stdEFM(standard deviation of EFM),are proposed.Consequently,a novel semi-open-loop mode selection algorithm based on EFM and selected AMR-WB+ features is proposed.The results of classifying test and listening test show that the performance of the novel algorithm is much better than that of the AMR-WB+ semi-open-loop coding mode selection algorithm.

Plasmon-assisted mode selection lasing in a lanthanide-based microcavity

Lanthanide-based microlasers have attracted considerable attention owing to their large anti-Stokes shifts,multiple emission bands,and narrow linewidths.Various applications of microlasers,such as optical communication,optical storage,and polarization imaging,require selecting the appropriate laser polarization mode and remote control of the laser properties.Here,we propose a unique plasmon-assisted method for the mode selection and remote control of microlasing using a lanthanide-based microcavity coupled with surface plasmon polaritons(SPPs)that propagate on a silver microplate.With this method,the transverse electrical(TE)mode of microlasers can be easily separated from the transverse magnetic(TM)mode.Because the SPPs excited on the silver microplate only support TM mode propagation,the reserved TE mode is resonance-enhanced in the microcavity and amplified by the local electromagnetic field.Meanwhile,lasingmode splitting can be observed under the near-field excitation of SPPs due to the coherent coupling between the microcavity and mirror microcavity modes.Benefiting from the long-distance propagation characteristics of tens of micrometers of SPPs on a silver microplate,remote excitation and control of upconversion microlasing can also be realized.These plasmon-assisted polarization mode-optional and remote-controllable upconversion microlasers have promising prospects in on-chip optoelectronic devices,encrypted optical information transmission,and high-precision sensors.

Mode analysis and design of 0.3-THz Clinotron

To develop a high-power continuous-wave terahertz source, a Clinotron operating at 0.3 THz is investigated. Based on the analyses of field distribution and coupling impedance, the dispersion characteristic of a rectangular resonator is preliminarily studied. The effective way to select fundamental mode to interact with the electron beam is especially studied.Finally, the structure is optimized by particle-in-cell simulation, and the problems of manufacture tolerance, current density threshold, and heat dissipation during Clinotron’s operation are also discussed. The optimum device can work with a good performance under the conditions of 8 k V and 60 m A. With the generation of signal frequency at 315.89 GHz and output power at 12 W on average, this device shows great prospects in the application of terahertz waves.

A high-power subterahertz surface wave oscillator with separated overmoded slow wave structures

A megawatt-level subterahertz surface wave oscillator （SWO） is proposed to obtain high conversion efficiency by using separated overmoded slow wave structures （SWSs）. Aiming at the repetitive operation and practical applications, the device driven by electron beam with modest energy and current is theoretically analyzed and verified. Then, the functions of the two SWS sections and the effect of the drift tube are investigated by using a particle-in-cell code to reveal how the proposed device achieves high efficiency. The mode analysis of the beam-wave interaction region in the device is also carded out, and the results indicate that multi-modes participate in the premodulation of the electron beam in the first SWS section, while the TM01 mode surface wave is successfully and dominantly excited and amplified in the second SWS section. Finally, a typical simulation result demonstrates that at a beam energy of 313 keV, beam current of 1.13 kA, and guiding magnetic field of above 3.5 T, a high-power subterahertz wave is obtained with an output power of about 70 MW at frequency 146.3 GHz, corresponding to the conversion efficiency of 20%. Compared with the results of the previous subterahertz overmoded SWOs with integral SWS and similar beam parameters, the efficiency increases almost 50% in the proposed device.

Visible-light all-fiber vortex lasers based on mode selective couplers

We demonstrate visible-light all-fiber vortex lasers by incorporating the home-made mode selective couplers (MSCs). The MSC at green or red wavebands is fabricated by specially designing and fusing a single-mode fiber (SMF) and a few-mode fiber (FMF). The MSCs inserted into visible fiber cavities act as power splitters and mode converters from the LP01 to LP11 mode at green and red wavelengths, respectively. The red-light all-fiber vortex laser is formed by a 10-cm Pr3+/Yb3+:ZBLAN fiber, a fiber Bragg grating, a fiber end-facet mirror and the MSC at 635 nm, which generates vortex beams with OAM±1 at 634.4 nm and an output power of 13 mW. The green-light all-fiber vortex laser consists of a 12-cm Ho3+:ZBLAN fiber, two fiber pigtail mirrors, and the MSC at 550 nm, which generates vortex beams with OAM±1 at 548.9 nm and an output power of 3 mW.

A Ku-band magnetically insulated transmission line oscillator with overmoded slow-wave-structure

In order to enhance the power capacity, an improved Ku-band magnetically insulated transmission line oscillator （MILO） with overmoded slow-wave-structure （SWS） is proposed and investigated numerically and experimentally. The analysis of the dispersion relationship and the resonant curve of the cold test indicate that the devine can operate at the near π mode of the TM01 mode, which is useful for mode selection and control. In the particle simulation, the improved Ku-band MILO generates a microwave with a power of 1.5 GW and a frequency of 12.3 GHz under an input voltage of 480 kV and input current of 42 kA. Finally, experimental investigation of the improved Ku-band MILO is carried out. A high-power microwave （HPM） with an average power of 800 MW, a frequency of 12.35 GHz, and pulse width of 35 ns is generated under a diode voltage of 500 kV and beam current of 43 kA. The consistency between the experimental and simulated far-field radiation pattern confirms that the operating mode of the improved Ku-band MILO is well controlled in zc mode of the TM01 mode.

Temperature-controlled mode selection of Er-doped random fiber laser with disordered Bragg gratings

In this paper, we proposed a way to realize an Er-doped random fiber laser(RFL) with a disordered fiber Bragg grating(FBG) array, as well as to control the lasing mode of the RFL by heating specific locations of the disordered FBG array. The disordered FBG array performs as both the gain medium and random distributed reflectors, which together with a tunable point reflector form the RFL. Coherent multi-mode random lasing is obtained with a threshold of between 7.5 and 10 mW and a power efficiency between 23% and 27% when the reflectivity of the point reflector changes from 4% to 50%. To control the lasing mode of random emission, a specific point of the disordered FBG array is heated so as to shift the wavelength of the FBG(s) at this point away from the other FBGs.Thus, different resonance cavities are formed, and the lasing mode can be controlled by changing the location of the heating point.

溶剂红135染料中六氯苯含量的测定

Determination of hexachlorobenzene (HCB) in the solvent red 135 by solvent extraction GC-MS with selected ion monitoring mode.The result showed that the detection limit is 0.05 mg/kg.The relative standard deviation is 3.3%.This method is suitable for the analysis of the HCB in the solvent red 135.

Cybertwin-Assisted Mode Selection in Ultra-Dense LEO Integrated Satellite-Terrestrial Network

Ultra-dense low earth orbit(LEO)integrated satellite-terrestrial network(ULISTN)has become an emerging paradigm to support massive access of Internet of things(IoT)in beyond fifth generation mobile networks(B5G).In ULISTN,there are two communication modes:cellular mode and satellite mode,where IoT users assessing terrestrial small base stations(TSBSs)and terrestrial-satellite terminals(TSTs)respectively.However,how to optimize the network performance and guarantee self-interests of the operator and IoT users in ULISTN is a challenging issue.In this paper,we propose a cybertwin-assisted joint mode selection and dynamic pricing(JMSDP)scheme for effective network management in ULISTN,where cybertwin serves as the intelligent agent.In JMSDP,the operator determines optimal access prices of TSBSs and TSTs,while each user selects the access mode according to access prices.Specifically,the operator conducts the Stackelberg game aiming at maximizing average throughput depending on the mode selection results of IoT users.Meanwhile,IoT users as followers adopt the evolutionary game to choose an access mode based on the access prices provided by the operator.Simulation results show that the proposed JMSDP can improve the average throughput and reduce the delay effectively,comparing with random access(RA)and maximum rate access.

Infra-Marginal Analysis Model for Provision Mode Selection for E-commerce Services

E-commerce has grown extraordinarily since the emergence of the internet, and many types of services are employed to accelerate this process. Service quality and productivity are two critical indicators to evaluate the competitiveness of e-commerce companies. Deciding which provision mode of e-commerce services （buy, sell, or self-provide） to adopt is a key operational strategy issue. This paper investigates the conditions and limitations of e-commerce services＇ optimal supply modes, and proposes a cost oriented infra-marginal model where service demand is considered an exogenous variable due to its non-elastic and unprofitable characteristics. By analyzing the main impact factors of this model, this paper infers provision mode selection strategies, which are determined by four factors： transaction cost, service price, service demand, and competitive advantages. Decision trees are derived from these strategies to help e-commerce companies make appropriate decisions. Finally, the proposed model＇s feasibility is verified by two case studies.

Mode selection of Lamb waves for the evaluation of solid plates with liquid loading

This paper studies the mode selection of Lamb waves for evaluating solid plates with liquid loading. For this purpose, the Lamb wave selected should have the features such as zero normal displacement components at the plate surface in contact with liquid, small dispersion, and maximum group velocity. It is found that when the phase velocity of Lamb wave is equal to the longitudinal wave velocity of the plate material, its normal displacement at the plate surface is always zero. Through the numerical analyses, the specific S2 Lamb wave that has zero normal displacement component at the plate surface, small dispersion and maximum group velocity compared with the other Lamb waves has been found. With respect to the specific S2 Lamb wave, some experimental examinations have been carried out. It is found that the liquid loading on the plate surface has less influence on the specific S2 Lamb wave signal but it can effectively eliminate the other signals. Moreover, the specific S2 Lamb wave selected exhibits the capability of detecting multiple defects in the solid plate with the liquid loading. It can be concluded that the specific S2 Lamb wave selected is suitable for the evaluation of solid plates with liquid loading.

Ten-Dimensional Quantum Dynamics Study of H+CH_(3)D→H_(2)+CH_(2)D Reaction

The mode selectivity of the H+CH_(3)D→H_(2)+CH_(2)D reaction was studied using a recently developed ten-dimensional time-dependent wave packet method.The reaction dynamics are studied for the reactant CH_(3)D initially from the ground state,the CH_(3) symmetry and asymmetry stretching excitation,the CD stretching excitation and the fundamental and the first overtone of the CH_(3) bending mode.The calculated reaction probabilities show that exciting either of the CH_(3) stretching modes enhances the reactivity in the collision energy range below 1.0 eV,while the CD stretching excitation does not obviously prompt the reaction.Fundamental CH_(3) bending excitation has nearly no effect on promoting reactivity.However,a significant enhancement is observed for the first overtone excitation of the CH_(3) bending mode,resulting from the Fermi resonance between the fundamental state of the CH_(3) symmetry stretching mode and the first overtone state of the CH_(3) bending mode.

Model construction for field operation machinery selection and configuration in wheat-maize double cropping system

In order to scientifically and reasonably select the field operation machinery in the wheat-maize double cropping system,first,the selection evaluation index system was constructed through the existing national standards and industry standards.Then the selection evaluation model was established based on the improved fuzzy comprehensive evaluation method.And the method of subjective weight and objective weight was used to overcome the drawbacks of the previous single weighting method that could not take into account the subject and object information of each indicator,and the weight value of each index was obtained in the evaluation system.Finally,the tillage process was used as an example,the field experiment was carried out to obtain the evaluation index value,and the model of selection evaluation was verified.The selection results of moldboard plough and rotary cultivator were as follows:the order of the comprehensive evaluation results of the moldboard plough results was ranked from high to low as 1LFK-435(IIM),1LFK-535(IM),1LF-342(IIIM),1LFT-445(IVM),1LFT-545(VM),and the best machine type of the moldboard plough was IIM;the order of the comprehensive evaluation results of the rotary cultivator was ranked from high to low as 1GQKGN-240(IIIR),1GKNSM-250(IVR),1GKN-230K(IR),1GKN-250K(IIR),1GQKGN-220(VR),and the optimal model of the rotary cultivator was IIIR.The experimental results showed that the results obtained by the evaluation model were in agreement with the local actual situation.The evaluation model will provide a scientific method for the selection of wheat and maize double cropping field operation machinery.