The Impact of Model Based Offset Scaling Technique on the Amplitude Variation with Offset Responses from 3D Seismic Data Acquired from the Tano Basin, Offshore Ghana

Amplitudes have been found to be a function of incident angle and offset. Hence data required to test for amplitude variation with angle or offset needs to have its amplitudes for all offsets preserved and not stacked. Amplitude Variation with Offset (AVO)/Amplitude Variation with Angle (AVA) is necessary to account for information in the offset/angle parameter (mode converted S-wave and P-wave velocities). Since amplitudes are a function of the converted S- and P-waves, it is important to investigate the dependence of amplitudes on the elastic (P- and S-waves) parameters from the seismic data. By modelling these effects for different reservoir fluids via fluid substitution, various AVO geobody classes present along the well and in the entire seismic cube can be observed. AVO analysis was performed on one test well (Well_1) and 3D pre-stack angle gathers from the Tano Basin. The analysis involves creating a synthetic model to infer the effect of offset scaling techniques on amplitude responses in the Tano basin as compared to the effect of unscaled seismic data. The spectral balance process was performed to match the amplitude spectra of all angle stacks to that of the mid (26°) stack on the test lines. The process had an effect primarily on the far (34° - 40°) stacks. The frequency content of these stacks slightly increased to match that of the near and mid stacks. In offset scaling process, the root mean square (RMS) amplitude comparison between the synthetic and seismic suggests that the amplitude of the far traces should be reduced relative to the nears by up to 16%. However, the exact scaler values depend on the time window considered. This suggests that the amplitude scaling with offset delivered from seismic processing is only approximately correct and needs to be checked with well synthetics and adjusted accordingly prior to use for AVO studies. The AVO attribute volumes generated were better at resolving anomalies on spectrally balanced and offset scaled data than data delivered from conventional processing. A typical class II AVO anomaly is seen along the test well from the cross-plot analysis and AVO attribute cube which indicates an oil filled reservoir.

Model based SOC estimation for high-power Li-ion battery packs used on FCHVs

A model based method which recruited the extended Kalman filter （EKF） to estimate the full state of charge （SOC） of Li-ion battery was proposed. The underlying dynamic behavior of the cell pack was described based on an equivalent circuit comprising of two capacitors and three resistors. Measurements in two tests were applied to compare the SOC estimated by model based EKF estimation with the SOC calculated by coulomb counting. Results have shown that the proposed method is able to perform a good estimation of the SOC of battery packs. Moreover, a corresponding battery management systems （BMS） including software and hardware based on this method was designed.

Auxiliary Model Based Multi-innovation Stochastic Gradient Identification Methods for Hammerstein Output-Error System

Special input signals identification method based on the auxiliary model based multi-innovation stochastic gradient algorithm for Hammerstein output-error system was proposed.The special input signals were used to realize the identification and separation of the Hammerstein model.As a result,the identification of the dynamic linear part can be separated from the static nonlinear elements without any redundant adjustable parameters.The auxiliary model based multi-innovation stochastic gradient algorithm was applied to identifying the serial link parameters of the Hammerstein model.The auxiliary model based multi-innovation stochastic gradient algorithm can avoid the influence of noise and improve the identification accuracy by changing the innovation length.The simulation results show the efficiency of the proposed method.

A Photonuclear Reaction Model Based on IQMD in Intermediate-Energy Region

A photonuclear reaction transport model based on an isospin-dependent quantum molecular dynamics model （IQMD） is presented in the intermediate energy region, which is named as GiQMD in this study. Methodology to simulate the course of the photonuclear reaction within the IQMD frame is described to study the photo- absorption cross section and π meson production, and the simulation results are compared with some available experimental data as well as the Giessen Boltzmann-Uehling-Uhlenbeck model.

A VISCOPLASTIC MODEL BASED ON NO-YIELD-SURFACE CONCEPT

The elasticjviscoplastic constitutive equation which describes deformation law of metal materials was suggested based on no-yield-surface concept and thermal activation theory of dislocation. The equation which takes account of effects of strain-rate, strain history, strain-rate history, hardening and temperature has stronger physical basis.Comparison of the theoretical prediction with experimental results of mechanical behaviours of Ti under conditions of uniaxial stress and room temperature shows good consistency.

3DV quality model based depth maps for view synthesis in FTV system

Depth maps are used for synthesis virtual view in free-viewpoint television （FTV） systems. When depth maps are derived using existing depth estimation methods, the depth distortions will cause undesirable artifacts in the synthesized views. To solve this problem, a 3D video quality model base depth maps （D-3DV） for virtual view synthesis and depth map coding in the FTV applications is proposed. First, the relationships between distortions in coded depth map and rendered view are derived. Then, a precisely 3DV quality model based depth characteristics is develop for the synthesized virtual views. Finally, based on D-3DV model, a multilateral filtering is applied as a pre-processed filter to reduce rendering artifacts. The experimental results evaluated by objective and subjective methods indicate that the proposed D-3DV model can reduce bit-rate of depth coding and achieve better rendering quality.

Multi-agent Based Hierarchy Simulation Models of Carrier-based Aircraft Catapult Launch

With the aid of multi-agent based modeling approach to complex systems, the hierarchy simulation models of carrier-based aircraft catapult launch are developed. Ocean, carrier, aircraft, and atmosphere are treated as aggregation agents, the detailed components like catapult, landing gears, and disturbances are considered as meta-agents, which belong to their aggregation agent. Thus, the model with two layers is formed i.e. the aggregation agent layer and the meta-agent layer. The information communication among all agents is described. The meta-agents within one aggregation agent communicate with each other directly by information sharing, but the meta-agents, which belong to different aggregation agents exchange their information through the aggregation layer first, and then perceive it from the sharing environment, that is the aggregation agent. Thus, not only the hierarchy model is built, but also the environment perceived by each agent is specified. Meanwhile, the problem of balancing the independency of agent and the resource consumption brought by real-time communication within multi-agent system （MAS） is resolved. Each agent involved in carrier-based aircraft catapult launch is depicted, with considering the interaction within disturbed atmospheric environment and multiple motion bodies including carrier, aircraft, and landing gears. The models of reactive agents among them are derived based on tensors, and the perceived messages and inner frameworks of each agent are characterized. Finally, some results of a simulation instance are given. The simulation and modeling of dynamic system based on multi-agent system is of benefit to express physical concepts and logical hierarchy clearly and precisely. The system model can easily draw in kinds of other agents to achieve a precise simulation of more complex system. This modeling technique makes the complex integral dynamic equations of multibodies decompose into parallel operations of single agent, and it is convenient to expand, maintain, and reuse the program codes.

A Custom Manipulator for Dental Implantation Through Model-Based Design

This paper presents a Model-Based Design(MBD)approach for the design and control of a customized manipulator intended for drilling and position-ing of dental implants accurately with minimal human intervention.While performing an intra-oral surgery for a prolonged duration within a limited oral cavity,the tremor of dentist's hand is inevitable.As a result,wielding the drilling tool and inserting the dental implants safely in accurate position and orientation is highly challenging even for experienced dentists.Therefore,we introduce a customized manipulator that is designed ergonomically by taking in to account the dental chair specifications and anthropomorphic data such that it can be readily mounted onto the existing dental chair.The manipulator can be used to drill holes for dental inserts and position them with improved accuracy and safety.Further-more,a thorough multi-body motion analysis of the manipulator was carried out by creating a virtual prototype of the manipulator and simulating its controlled movements in various scenarios.The overall design was prepared and validated in simulation using Solid works,MATLAB and Simulink through Model Based Design(MBD)approach.The motion simulation results indicate that the manipulator could be built as a prototype readily.

DiagDO: an efficient model based diagnosis approach with multiple observations

Model-based diagnosis(MBD)with multiple observations shows its significance in identifying fault location.The existing approaches for MBD with multiple observations use observations which is inconsistent with the prediction of the system.In this paper,we proposed a novel diagnosis approach,namely,the Diagnosis with Different Observations(DiagDO),to exploit the diagnosis when given a set of pseudo normal observations and a set of abnormal observations.Three ideas are proposed in this paper.First,for each pseudo normal observation,we propagate the value of system inputs and gain fanin-free edges to shrink the size of possible faulty components.Second,for each abnormal observation,we utilize filtered nodes to seek surely normal components.Finally,we encode all the surely normal components and parts of dominated components into hard clauses and compute diagnosis using the MaxSAT solver and MCS algorithm.Extensive tests on the ISCAS'85 and ITC'99 benchmarks show that our approach performs better than the state-of-the-art algorithms.

Hierarchy Bayesian model based services awareness of high-speed optical access networks

As the speed of optical access networks soars with ever increasing multiple services, the service-supporting ability of optical access networks suffers greatly from the shortage of service awareness. Aiming to solve this problem, a hierarchy Bayesian model based services awareness mechanism is proposed for high-speed optical access networks. This approach builds a so-called hierarchy Bayesian model, according to the structure of typical optical access networks. Moreover, the proposed scheme is able to conduct simple services awareness operation in each optical network unit(ONU) and to perform complex services awareness from the whole view of system in optical line terminal(OLT). Simulation results show that the proposed scheme is able to achieve better quality of services(Qo S), in terms of packet loss rate and time delay.

Modeling of a Lithium-Ion Capacitor and Its Charging and Discharging Circuit in a Model-Based Design

For several years now, electric vehicles (EVs) have been expected to become widely available in the micro-mobility field. However, the insufficiency of such vehicles’ battery-charging and discharging performance has limited their practical use. A hybrid energy storage system, which comprises a capacitor and battery, is a promising solution to this problem;however, to apply model-based designs, which are indispensable to embedded systems, such as the electronic control units used in EVs, a simple and accurate capacitor model is required. Within this framework, a lithium-ion capacitor (LIC) model is proposed, and its charging and discharging performances are evaluated against an actual LIC. The model corresponds accurately to the actual LIC, and the results indicate that the proposed LIC model will work well when used with Model-Based Design (MBD).

Urban Metabolism Based on Emergy and Slack Based Model: A Case Study of Beijing, China

The key to studying urban sustainable development depends on quantifying stores, efficiencies of urban metabolisms and capturing urban metabolisms′ mechanisms. This paper builds up the metabolic emergy account and quantifies some important concepts of emergy stores. Emphasis is placed on the urban metabolic model based on the slack based model(SBM) method to measure urban metabolic efficiencies. Urban metabolic mechanisms are discussed by using the regression method. By integrating these models, this paper analyzes the urban metabolic development in Beijing from 2001 to 2010. We conclude that the metabolic emergy stores of Beijing increased significantly from 2001 to 2010, with the emergy imported accounting for most of the increase. The metabolic efficiencies in Beijing have improved since the 2008 Olympic Games. The population, economic growth, industrial structures, and environmental governance positively affect the overall urban metabolism, while the land expansion, urbanization and environmentally technical levels hinder the improving of urban metabolic efficiencies. The SBM metabolic method and the regression model based on the emergy analysis provide insights into the urban metabolic efficiencies and the mechanism. They can promote to integrate such concepts into their sustainability analyses and policy decisions.

Flow Field and Temperature Field in GaN-MOCVD Reactor Based on Computational Fluid Dynamics Modeling

Metal organic chenlical vapor deposition （AIOCVD） growth systems arc one of the. main types of equipment used for growing single crystal materials, such as GaN. To obtain fihn epitaxial materials with uniform performanee, the flow field and ternperature field in a GaN-MOCVD reactor are investigated by modeling and simulating. To make the simulation results more consistent with the actual situation, the gases in the reactor are considered to be compressible, making it possible to investigate the distributions of gas density and pressure in the reactor. The computational fluid dynamics method is used to stud,v the effects of inlet gas flow velocity, pressure in the reactor, rotational speed of graphite susceptor, and gases used in the growth, which has great guiding~ significance for the growth of GaN fihn materials.

DIMENSION VARIATION OF FEATURE-BASED MODEL BY OPERATING DIRECTLY ON B-REP

ＤＩＭＥＮＳＩＯＮＶＡＲＩＡＴＩＯＮＯＦＦＥＡＴＵＲＥ┐ＢＡＳＥＤＭＯＤＥＬＢＹＯＰＥＲＡＴＩＮＧＤＩＲＥＣＴＬＹＯＮＢ┐ＲＥＰＨＥＸｉａｏｚｈａｏ（何小朝），ＷＡＮＧＺｏｎｇｙａｎ（王宗彦）ＰＥＮＧＷｅｉ（彭维），ＺＨＡＮＧＴｉｅｃｈａｎｇ（张铁昌...

Knowledge-Based Multifaceted Modeling Methodology for Open Complex Giant Systems

In this paper, the structure characteristics of open complex giant systems are concretely analysed in depth, thus the view and its significance to support the meta synthesis engineering with manifold knowledge models are clarified. Furthermore, the knowledge based multifaceted modeling methodology for open complex giant systems is emphatically studied. The major points are as follows: (1) nonlinear mechanism and general information partition law; (2) from the symmetry and similarity to the acquisition of construction knowledge; (3) structures for hierarchical and nonhierarchical organizations; (4) the integration of manifold knowledge models; (5) the methodology of knowledge based multifaceted modeling.

Blended-fuel based EDC combustion model and its application in heptane-ethanol fire simulation

The blended-fuel based eddy-dissipation-concept combustion model was newly developed in the FireFOAM framework, and applied to simulate 30 cm×30 cm heptane-ethanol pool fire. Comparison was made of fire height, centerline temperature against experimental measurements, which shows that they match very well with each other. However, further studies are needed to examine the validation of this model in fire simulations with various scales.

Prediction Model of Soil Nutrients Loss Based on Artificial Neural Network

On the basis of Artificial Neural Network theory, a back propagation neural network with one middle layer is building in this paper, and its algorithms is also given, Using this BP network model, study the case of Malian-River basin. The results by calculating show that the solution based on BP algorithms are consis- tent with those based multiple - variables linear regression model. They also indicate that BP model in this paper is reasonable and BP algorithms are feasible.

Human induced pluripotent stem cell based in vitro models of the blood-brain barrier： the future standard？

There is an urgent and tremendous need for human dis- ease models in drug development in order to improve pre- clinical predictability. In the case of brain disorders drugs have to cross the blood-brain barrier （BBB） to enter the central nervous system （CNS）. It was estimated that more than 95% of the drugs cannot cross the BBB.

High-Temperature Performance Analysis of AlGaN/GaN Polarization Doped Field Effect Transistors Based on the Quasi-Multi-Channel Model

We report on the temperature-dependent dc performance of A1GaN/GaN polarization doped field effect transistors （PolFETs）. The rough decrements of drain current and transeonductance with the operation temperature are observed. Compared with the conventional HFETs, the drain current drop of the PolFET is smaller. The transeonductance drop of PolFETs at different gate biases shows different temperature dependences. From the aspect of the unique carrier behaviors of graded AlGaN/GaN heterostructure, we propose a quasi-multi-channel model to investigate the physics behind the temperature-dependent performance of AlGaN/GaN PolFETs.

Ab Initio Calculation of Dielectric Function in Wurtzite GaN Based on Walter's Model

The wavelength-dependent and frequency-dependent dielectric function of wurtzite-GaN is cMculated totally from fundamental parameters such as the lattice constant using Waiter＇s ab initio model. The errors occurring in the cMculation are carefully reduced by/inear interpolation of energy data. The Kramers-Kronig transform of the real part of greater range is obtained by extrapolation of the reM part. The calculation is time-consuming but meaningful The long-wave results are similar to the experimental data of the photon and are useful for related investigation of properties of wide-gap semiconductors such as electron scattering like the Auger recombination and impact ionization.