Preparation of Modified UiO-66 Catalyst and Its Catalytic Performance for NH_(3)-SCR Denitration

Zirconium-based metal-organic framework UiO-66 was successfully prepared by solvothermal method,and UiO-66 was modified by adding regulators such as formic acid,acetic acid,and hydrochloric acid.The NH_(3)-SCR reactivity of the samples was evaluated by the denitration activity evaluation system,and the UiO-66 and the regulator-modified UiO-66 were characterized by XRD,SEM,BET,FTIR,TG,NH_(3)-TPD,etc.,the effects of regulator types on the structure and properties of UiO-66 were investigated.The experimental results show that,after adding the modifier,the morphology of UiO-66 changes from irregular quadrilateral with serious agglomeration to particles with regular crystal shape and good dispersibility,and the crystal morphology of the catalyst is improved.In addition,after adding the modifier,UiO-66 has a larger specific surface area and stronger surface acidity,which optimizes the catalytic performance of UiO-66.The catalytic performance test results of NH_(3)-SCR show that the low-temperature activity of UiO-66 is poor,and it only shows a certain catalytic activity at higher temperatures.The catalytic activity of UiO-66 was significantly improved after adding the regulator.Among them,the UiO-66-HCl modified with hydrochloric acid had the best catalytic activity,and the denitration rate reached 70%when the denitration temperature was 380℃.

Accelerating the Screening of Modified MA_(2)Z_(4) Catalysts for Hydrogen Evolution Reaction by Deep Learning-Based Local Geometric Analysis

Machine learning(ML)integrated with density functional theory(DFT)calculations have recently been used to accelerate the design and discovery of single-atom catalysts(SACs)by establishing deep structure–activity relationships.The traditional ML models are always difficult to identify the structural differences among the single-atom systems with different modification methods,leading to the limitation of the potential application range.Aiming to the structural properties of several typical two-dimensional MA_(2)Z_(4)-based single-atom systems(bare MA_(2)Z_(4) and metal single-atom doped/supported MA_(2)Z_(4)),an improved crystal graph convolutional neural network(CGCNN)classification model was employed,instead of the traditional machine learning regression model,to address the challenge of incompatibility in the studied systems.The CGCNN model was optimized using crystal graph representation in which the geometric configuration was divided into active layer,surface layer,and bulk layer(ASB-GCNN).Through ML and DFT calculations,five potential single-atom hydrogen evolution reaction(HER)catalysts were screened from chemical space of 600 MA_(2)Z_(4)-based materials,especially V_(1)/HfSn_(2)N_(4)(S)with high stability and activity(Δ_(GH*)is 0.06 eV).Further projected density of states(pDOS)analysis in combination with the wave function analysis of the SAC-H bond revealed that the SAC-dz^(2)orbital coincided with the H-s orbital around the energy level of−2.50 eV,and orbital analysis confirmed the formation ofσbonds.This study provides an efficient multistep screening design framework of metal single-atom catalyst for HER systems with similar two-dimensional supports but different geometric configurations.

Ethylene/1-Hexene Copolymerization with Modified Ziegler-Natta Catalyst

Siloxane compounds were treated with the compounds containing internal donors,such as aromatic ester,phosphate,or 1,3-diether compounds,and the resulting intermediates were further reacted with TiCl4 to form the modified Ziegler-Natta catalysts for ethylene/1-hexene(E-H)copolymerization.Using the modified Ziegler-Natta catalysts,the effect of the internal donors and the molar ratio of alcohol to magnesium on the catalyst performance was investigated by the orthogonal experiments.The synthetic method of the catalysts was also optimized by choosing the proper way to mix the internal donors.The branch degree,sequence structure,molecular weight,and molecular weight distribution of the copolymer products were determined by Fourier transform infrared spectroscopy(FTIR),carbon-13 nuclear magnetic resonance(^13C NMR)spectrometry and gel permeation chromatography(GPC).Under the optimum conditions,the catalytic system with tetraethyl orthosilicate and 2,2-dimethoxypropane as the internal donors exhibited the best performance with an activity of 926.74 g copolymer/(g Cat·h^?1).The branch degree,1-hexene content,and molecular weight distribution of the resulting copolymers reached up to 40 branches/1000C,5.99%and 5.8,respectively.

Effect of Ni loadings on the activity and coke formation of MgO-modified Ni/Al_2O_3 nanocatalyst in dry reforming of methane

MgO-modified Ni/Al2O3 catalysts with different Ni loadings were prepared and employed in dry reforming of methane （DRM）. The effect of Ni loadings on the activity and coke formation of Ni/MgO-A1203 catalysts were investigated. The synthesized catalysts were characterized by XRD, N2 adsorption-desorption, SEM, TPO and TPR techniques. The obtained results showed that increasing nickel loading decreased the BET surface area and increased the catalytic activity and amount of deposited carbon. In addition, the effect of gas hourly space velocity （GHSV） and feed ratio were studied.

Pt-Ru Catalysts Prepared by a Modified Polyol Process for Direct Methanol Fuel Cells

Supported PtRu/C catalysts used in direct methanol fuel cells (DMFCs) were prepared by a new modified polyol method. Transmission electron microscopy (TEM), X-ray diffraction (XRD) and cyclic voltammograms (CVs) were carried out to characterize the morphology, composition and the electrochemical properties of the PtRu/C catalyst. The results revealed that the PtRu nanoparticles with small average particle size (≈2.5 nm), and highly dispersed on the carbon support. The PtRu/C catalyst exhibited high catalytic activity and anti poisoned performance than that of the JM PtRu/C. It is imply that the modified polyol method is efficient for PtRu/C catalyst preparation.

Study on Deactivation and Regeneration of Modified Red Mud Catalyst Used in Biodiesel Production

Deactivation of solid catalyst often occurs in biodiesel production. In this work, deactivated modified red mud catalysts used in biodiesel production were regenerated with hexane and calcination treatments. The deactivated and regenerated catalysts were characterized using XRD, FTIR, SEM, TG, N2 adsorption, measured for their basic strength, and tested in the transesterification of canola oil. The results revealed that the main cause of the catalyst deactivation is due to obstruction of the active sites by contaminants. The regeneration by washing with hexane followed by calcination can effectively improve the properties of the deactivated catalyst and increase its catalytic activity.

Synthesis and Characterization of Poly（Lactide）s Using Novel Solid Cloisite Modified Tin Catalyst

A novel cloisite modified solid catalyst was prepared in a single step from commercially available starting materials for the first time. The ring opening polymerization of L-lactide and D-lactide using this cloisite modified solid catalyst resulted in homopolymers of 75,000 and PDI = 1.6 and the maximum molecular weight （Mw） i.e. 180,000 with PDI = 1.9 were obtained. The catalytic activity ofcloisite modified solid catalyst was compared with the conventional stannous octoate catalyst and found superior to stannous octoate in all respect such as conversion, molecular weight and molecular weight distribution etc.. Moreover, the maximum molecular weight i.e. 180,000 was obtained at 220 ℃, whereas, transesterification reaction predominate in presence of stannous octoate The linear structure was confirmed by quantitative ^13C NMR Spectroscopy. Blend films were obtained by casting mixed solutions of poly （D-lactide） and poly （L-lactide） at various compositions, and stereocomplex was formed at 50/50 composition with molecular weight of 75,000.

Direct decomposition of nitric oxide in low temperature over iron-based perovskite-type catalyst modified by Ru

Iron-based perovskite-type compounds modified by Ru were prepared through sol-gel process to study its catalytic activity of NOx direct decomposition at low temperature and evaluate the conversion of NO under the experimental conditions. The catalytic activity of La 0.9Ce 0.1Fe 0.8-nCo 0.2RunO3 （n=0.01,0.03,0.05,0.07,0.09）series for the NO, NO-CO two components, CO-HC-NO three components were also analyzed. The catalytic investigation evidenced that the presence of Ru is necessary for making highly activity in decomposition of nitric oxide even at low temperature（400 ℃）and La 0.9Ce 0.9Fe 0.75Co 0.2Ru 0.05O3 （n=0.05） has better activity in all the samples, the conversion of it is 58.5%. With the reducing gas（CO,C3H6）added into the gas, the catalyst displayed very high activity in decomposition of NO and the conversion of it is 80% and 92.5% separately.

IR AND EPR STUDIES OF THE NUCLEAR ALKYLATION OF TOLUENE AND ETHYLENE ON THE MODIFIED Mg—AND P—ZSM—5 CATALYST

The surface intermediate (C_2H_5^+ and CH_3C_6H_5^+) and the reactive pathway of nuclear alkylation of toluene with ethylene to para—ethyl toluene over Mg salt and phosphorus acid modified ZSM—5 zeolites have been studied by 1R and EPR methods.

THE DIFFUSION OF m-XYLENE ON MODIFIED ZnZSM-5 AROMATIZATION CATALYST BEFORE AND AFTER COKING

The effect of coking amount for diffusion rate of m—xylene in a pore of the modified ZnZSM—5 aromatization catalyst has been studied.

EFFECT OF Ni CRYSTAL SIZE DISTRIBUTION ON THE ANTICOKING BEHAVIOR OF La-MODIFIED Ni/α-Al_2O_3 CATALYSTS

The crystal size distribution（CSD）was determined with small angle X-ray scattering technique.Theanticoking property of Ni-catalysts was investigated with the steam reforming of n-heptane in a TG-monitoredflow reactor.The results of this study show that the rate of coking on the supported Ni-catalysts depends main-ly on the percentage content of the large size fraction（25-70nm）of Ni-crystallites,and that the dispersion ofNi-crystallites and the anticoking property of the Ni/α-Al2O3 catalysts were promoted obviously by theLa2O3-modification method.The variation of the Ni-CSD and the anticoking property of the catalysts were fur-ther tested through different periods of hydrothermal treatment.It is found that the content of the largeNi-crystal size fraction and the coking rate pass correspondingly through a maximum.

Complete Oxidation of Methane over Palladium Supported on Alumina Modified with Calcium,Lanthanum,and Cerium Ions

The activity and thermal stability of Pd/Al2O3 and Pd/（Al2O3＋MOx） （M=Ca, La, Ce） palladium catalysts in the reaction of complete oxidation of methane are presented in this study. The catalyst supports were prepared by sol-gel method and they were dried either conventionally or with supercritical carbon dioxide. Then they were impregnated with palladium nitrate solution. The catalysts with unmodified alumina had a high surface area. The activity and thermal stability of the aluminasupported catalyst was also very high. The introduction of calcium, lanthanum, or cerium oxide into alumina support caused a decrease of the surface area in the way dependent on the support precursor drying method. These modifiers decreased the activity of palladium catalysts, and they required higher temperatures for the complete oxidation of methane than unmodified Pd/Al2O3. The improvement of the palladium activity by lanthanum and cerium support modifier was observed only at low temperatures of the reaction.

Bis(trifluoromethylsulfonyl)phenylamines as Internal Donors for Ziegler-Natta Polymerization Catalysts

Several bis（trifluoromethylsulfonyl）phenylamines have been synthesized and used as internal donors for the preparation of heterogeneous Ziegler-Natta catalysts for propylene polymerization. These new cata- lysts are highly active and stereospecific in combination with an external donor for the polymerization of propylene. The activity of these catalysts is dramatically influenced by the electronic capability of the phenyl substituents on the sulfonyl phenylamines. Therefore, the performances of the catalysts can be modified by adjusting the electronic property of the phenyl substituents of the sulfonyl phenylamines.

COPOLYMERIZATION OF PROPYLENE WITH HINDERED PIPERIDINE MONOMER OVER A HIGH ACTIVITY SUPPORTED ZIEGLER-NATTA CATALYST

Copolymerization of propylene and hindered piperidine monomers was carried out over a high activity supported Ziegler-Natta catalyst, using Al(C2H5)(3) as cocatalyst. Factors which affect the copolymerization were studied, The copolymers exhibited high light stability without adding extra light stabilizers. A self-stabilized polypropylene was prepared.

STUDY ON 1-HEXENE POLYMERIZATION BASED ON ZIEGLER-NATTA CATALYSTS WITH DOPED SUPPORT

A series of Ti/Mg supported catalysts are prepared by using ball-milled mixtures of MgCl2-ethanol adducts and NaCl as supports, and 1-hexene polymerizations catalyzed by the novel catalysts are studied. It is found that the molecular weight distribution of poly(1-hexene) becomes apparently narrower when catalysts with doped supports are used, indicating that changing the structure of the support is an effective way to regulate the active center distribution of heterogeneous Ziegler-Natta catalyst.

Study of a Novel Fourth-generation Supported Ziegler-Natta Catalyst for Propylene Polymerization: Relationship between Catalyst Structure and Polymerization Properties

This article presents a detailed structural study of a new spherical Mg Cl2-supported Ti Cl4 Ziegler-Natta catalyst for isotactic propylene polymerization, and researches on the relationship between catalyst structure and polymer properties. The spherical support with the chemical composition of CH3CH2 OMg OCH(CH2Cl)2 has been synthesized from a new dispersion system and is used as the supporting material to prepare Ziegler-Natta catalyst. The XRD analysis indicates that the catalyst is fully activated with δ-Mg Cl2 in the active catalyst. The far-IR spectrometric results confirm again the presence of δ-Mg Cl2 in the active catalyst. Textural property of the active catalyst exhibits high surface area coupled with high porosity. The high activity in propylene polymerization is mainly ascribed to the full activation and the porous structure of the catalyst. Scanning electron microscopy/energy dispersive spectrometer mapping results indicate a uniform titanium distribution throughout the catalyst particles. Particle size analysis shows that the catalyst has a narrow particle size distribution. The perfect spherical shape, uniform titanium distribution and narrow particle size distribution of the catalyst confirm the advantage of polymer particles production with less fines. The solid state 13 C NMR and mid-IR spectroscopic analyses indicate that there exists strong complexation between diisobutyl phthalate and Mg Cl2, which leads to the high isotacticity of polypropylene.

Preparation of Ultra-High Molecular Weight Polypropylene Using Ziegler-Natta Catalyst via Combining Internal Electron Donor and Cocatalyst Loading

Due to the development of the new energy industry,polypropylene with ultra-high molecular weight plays a crucial role for battery isolation membrane.This work investigated the effect of internal electron donor of Ziegler-Natta catalyst system on the molecular weight of the obtained polypropylene.The scanning electron microscope(SEM)and Canon camera were used to characterize the surface morphologies of catalyst particles and polymer particles,respectively.Compared with the polypropylene particles featuring a spherical shape,these study results confirmed that the morphology duplication theory from the catalyst particle to the morphology of polymer particle was exhibited.The gel permeation chromatography(GPC)results revealed that the obtained polypropylene has a much higher average molecular weight than those prepared by conventional method.The Fourier transform infrared spectrometry(FT-IR)and X-ray photoelectron spectroscopy(XPS)revealed that the carbonyl oxygen atom on ester group was preferentially bound to Mg and Ti,as compared to the ether oxygen atom.The XPS results showed that the ratio of Ti^(3+)/Ti^(4+)could be changed by internal electron donors.When Ti3+content was nearly 99%in the Ziegler-Natta catalyst system,isotactic polypropylene with an ultra-high molecular weight of up to 1.42×10^(6)g/mol was obtained by Cat.3.This result implied that internal electron donor ID3 could reduce theβ-hydride elimination reaction to further increase the molecular weight of the obtained polymer.

EFFECTS OF EXTERNAL DONOR ON ACTIVE CENTER DISTRIBUTION OF SUPPORTED ZIEGLER-NATTA CATALYST

The composition distribution (CD) and microisotacticity distribution (ID) of propene/1-hexene copolymer synthesized by MgCl2/DIBP/TiCl4 (DIBP: diisobutyl phthalate) were determined by fractionating the copolymers according to crystallinity and characterizing the fractions by (CNMR)-C-13. The effects of two alkoxysilane donors, triethoxyphenylsilane (PTES) and dimethoxydi-tert-butylsilane (TBMS), on CD and ID of the copolymers were compared. Three main parts in the CD diagram of each copolymer were distinguished, which were correlated to active center distribution (ACD) based on three groups of different active centers. By studying the changes in l-hexene content, microisotacticity and reactivity ratio product of three typical fractions, the effects of external donor on ACD were better elucidated. It was found that TBMS shows much stronger effects on ACD than PTES. In the former system, most fractions were produced on active centers with relatively lower r(1)r(2), higher reactivity to I-hexene, and higher stereospecificity as compared to the system without external donor. It is concluded that the observed very extensive changes in ACD are mainly resulted by the formation of new types of active centers, possibly by coordination of external donor to certain positions on the catalyst.

Study on the distribution of active centers in novel low Ti-loading MgCl2-supported Ziegler-Natta catalyst

Novel MgCl2-supported Ziegler-Natta (Z-N) catalysts prepared using a new one-pot ball milling method can effectively control the amounts of Ti-loading in the catalysts. Complex GPC data on polypropylene synthesized by these novel catalysts were analyzed using the method of fitting the molecular weight distribution (MWD) curves with a multiple Flory-Schulz function. It was found that multiple active centers exist in these novel catalysts. Detailed study of the effects of the Ti-loadings in the catalysts on the distribution of the active centers showed that the Ti-loadings in the novel MgCl2-supported Z-N catalysts might affect the proportion of each type of active centers; and might be the main factor responsible for the effect of the Ti-loadings on the microstructure, the molecular weight and molecular weight distribution width of the resultant polymer, the catalytic activity and polymerization kinetics.

MODIFICATION OF PALLADIUM METALLIC CATALYST WITH POLYMER-ANCHORED THIOETHER LIGANDS

A well-dispersed metallic palladium catalyst modified by polymer-anchored thioether ligands was used for the hydrogenation of cyclopentadiene to cyclopentene with high activity and selectivity in ambient condition. The evidences to show the modification of catalytic properties by polymer anchored ligands were given.