Glassy carbon electrode modified with multi-walled carbon nanotubes sensor for the quantihication of antihistamine drug pheniramine in solubilized systems

A sensitive electroanalytical method for quantification of pheniramine in pharmaceutical formulation has been investigated on the basis of the enhanced electrochemical response at glassy carbon electrode modified with multi-walled carbon nanotubes in the presence of sodium lauryl sulfate.The experimental results suggest that the phcniramine in anionic surfactant solution exhibits electrocatalytic effect resulting in a marked enhancement of the peak current response.Peak current response is linearly dependent on the concentration of pheniramine in the range 200-1500 μg/mL with correlation coefficient 0.9987.The limit of detection is 58.31 μg/m L.The modified electrode shows good sensitivity and repeatability.

Determination of 6-Mercaptopurine in Rat Blood by Microdialysis Coupled with High Performance Liquid Chromatography on a Functionalized Multi-wall Carbon Nanotubes Modified Electrode

A new chemically modified electrode(CME) immobilized on the surface of multi-wall carbon nanotubes functionalized with carboxylic groups was fabricated. The results indicate that the CME exhibits efficiently electrocatalytic oxidation of 6-mercaptopurine(6-MP). The CME can be used as the working electrode in the liquid chromatography for the determination of 6-MP. The peak current of 6-MP is linearly changed with its concentration ranging from 4.0×10 -7 to 1.0×10 -4 mol/L with the calculated detection limit (S/N=3) of 2.0×10 -7 mol/L. Coupled with microdialysis sampling, the method has been successfully applied to assessing the content of 6-MP in rat blood.

Pyrolyzed Iron Phthalocyanine-Modified Multi-Walled Carbon Nanotubes as Composite Anode in Marine Sediment Microbial Fuel Cells and Its Electrochemical Performance

Improving the performance of anode is a crucial step for increasing output power of marine sediment microbial fuel cells(MSMFCs)to drive marine monitor to work for a long term on the ocean floor.A pyrolyzed iron phthalocyanine modified multi-walled carbon nanotubes composite(FePc/MWCNTs)has been utilized as a novel nodified anode in the MSMFC.Its structure of the composite modified anode and electrochemical performance have been investigated respectively in the paper.There is a substantial improvement in electron-transfer efficiency from the bacteria biofilm to the modified anode via the pyrolyzed FePc/MWCNTs composite based on their cyclic voltammetry(CV)and Tafel curves.The electron transfer kinetic activity of the FePc/MWCNTs-modified anode is 1.86 times higher than of the unmodified anode.The maximum power density of the modified MSMFC was 572.3±14 m W m^-2,which is 2.6 times larger than the unmodified one(218.3±11 m W m^-2).The anodic structure and cell scale would be greatly minimized to obtain the same output power by the modified MSMFC,so that it will make the MSMFC to be easily deployed on the remote ocean floor.Therefore,it would have a great significance for us to design a novel and renewable long term power source.Finally,a novel molecular synergetic mechanism is proposed to elucidate its excellent electrochemical performance.

A comparative study of polymer nanocomposites containing multi-walled carbon nanotubes and graphene nanoplatelets

Featuring exceptional mechanical and functional performance, MWCNTs and graphene(nano)platelets(GNPs or Gn Ps;each platelet below 10 nm in thickness) have been increasingly used for the development of polymer nanocomposites. Since MWCNTs are now cost-effective at US$30 per kg for industrial applications, this work starts by briefly reviewing the disentanglement and surface modification of MWCNTs as well as the properties of the resulting polymer nanocomposites. GNPs can be made through the thermal treatment of graphite intercalation compounds followed by ultrasonication;GNPs would have lower cost yet higher electrical conductivity over 1,400 S cmthan MWCNTs. Through proper surface modification and compounding techniques, both types of fillers can reinforce or toughen polymers and simultaneously add anti-static performance. A high ratio of MWCNTs to GNPs would increase the synergy for polymers. Green, solvent-free systhesis methods are desired for polymer nanocomposites. Perspectives on the limitations, current challenges and future prospects are provided.

Effects of layer number and initial pressure on continuum-based buckling analysis of multi-walled carbon nanotubes accounting for van der Waals interaction

The structural instability of multi-walled carbon nanotubes(MWCNTs) has captured extensive attention due to the unique characteristic of extremely thin hollow cylinder structure. The previous studies usually focus on the buckling behavior without considering the effects of the wall number and initial pressure. In this paper, the axial buckling behavior of MWCNTs with the length-to-outermost radius ratio less than 20 is investigated within the framework of the Donnell shell theory. The governing equations for the infinitesimal buckling of MWCNTs are established, accounting for the van der Waals(vd W) interaction between layers. The effects of the wall number, initial pressure prior to buckling, and aspect ratio on the critical buckling mode, buckling load, and buckling strain are discussed, respectively. Specially, the four-walled and twenty-walled CNTs are studied in detail, indicating the fact that the buckling instability may occur in other layers besides the outermost layer. The obtained results extend the buckling analysis of the continuum-based model, and provide theoretical support for the application of CNTs.

Effects of temperature change on the rheological property of modified multiwall carbon nanotubes

Solvent-free nanofluids hold promise for many technologically significant applications.The liquid-like behavior,a typical rheological property of solvent-free nanofluids,has aroused considerable interests.However,there has been still lack of efficient methods to predict and control the liquid-like behavior of solvent-free nanofluids.In this paper,we propose a semi-discrete dynamic system with stochastic excitation describing the temperature change effects on the rheological property of multiwall carbon nanotubes(MWCNTs)modified by grafting sulfonic acid terminated organosilanes as corona and tertiary amine as canopy,which is a typical covalent-type solvent-free nanofluid system.The vibration of the grafting branches is simulated by employing a structure-preserving approach,and the shear force of grafting branches at the fixed end is computed subsequently.By taking the shear forces as an excitation acting on the MWCNTs,the axial motion of the MWCNTs is solved with the 7-point Gauss-Kronrod quadrature rule.The critical temperature associated with the appearance of the liquid-like behavior as well as the upper bound of the moving speed of the modified MWCNTs is determined,which can be used to predict and control the liquid-like behavior of the modified MWCNTs in engineering applications.

Mechanical Properties and Microstructure of Sulfur Aluminate Cement Composites Reinforced by Multi-walled Carbon Nanotubes

The effect of multi-walled carbon nanotubes（MWCNTs） on the mechanical properties and microstructure of sulfur aluminate cement（SAC） composites was investigated. The dispersed MWCNTs were added into SAC in various weight contents.The results of mechanical properties of the MWCNTs/SAC composites indicated that the addition of 0.08 wt% MWCNTs can improve the SAC compressive strength, flexural strength, and bend-press ratio by 15.54%, 52.38%, and 31.30% at maximum, respectively. The degree of SAC hydration and porosity and pore size distribution of the matrix were measured by X-ray diffraction（XRD）, thermal analysis（TG/DTG）, and mercury intrusion porosimetry（MIP）. Results show that the addition of MWCNTs in SAC composites can promote the hydration of SAC and the formation of C-S-H gel, reduce the porosity and refine the pore size distribution of the matrix. The microstructure was characterized by scanning electron microscopy（SEM） and energy dispersive spectroscopy（EDS）. It is found that the MWCNTs have been dispersed homogeneously between the hydration products of SAC paste and act as bridges and networks between cracks and voids, which prevents the development of the cracks and transfers the load.

Improvement of Interlaminar Fracture Properties of Out of Autoclave Manufactured Carbon Fiber Reinforced Polymers Using Multi-Walled Carbon Nanotubes

The present study aims to the development of Out of Autoclave (OoA) Carbon Fiber Reinforced Polymers (CFRPs) with increased interlaminar fracture toughness by using MWCNTs. The introduction of MWCNTs into the structure of CFRPs has been succeeded by using carbon nanotube-enriched sizing agent for the pretreatment of the fiber preform using an in-house developed methodology that can be easily scaled up. The positive effect of the proposed methodology on the interlaminar fracture toughness of the CFRP laminate was assessed by the increase of Mode I and Mode II interlaminar fracture toughness of the composites. Different wt% MWCNTs concentrations were used (namely 0.5%, 1%, 1.5% and 2.5%). It was found that the nanomodified composites exhibit a significant increase of the interlaminar critical strain energy release rate GIC and GIIC of the order of 103% and 62% respectively, in the case of 1.5 wt% MWCNTs weight content. Scanning Electron Microscopy (SEM) of the fracture surfaces of CFRP samples revealed the contribution and the associated synergistic mechanisms of MWCNTs to the increase of the crack propagation resistance in the case of nano-modified CFRPs compared to the reference material.

Structure and Properties of Self-assembled Narural Rubber/Multi-walled Carbon Nanotube Composites

Natural rubber （NR）/multi-walled carbon nanotube （MWCNTs） composites were prepared by combining self-assembly and latex compounding techniques.The acid-treated MWCNTs （H2SO4：HNO3=3：1,volume ratio） were self-assembled with poly （diallyldimethylammonium chloride） （PDDA） through electrostatic adhesion.In the second assembling,NR/MWCNTs composites were developed by mixing MWCNTs/PDDA solution with NR latex.The results show that MWCNTs are homogenously distributed throughout the NR matrix as single tube and present a great interfacial adhesion with NR phase when MWCNTs contents are less than 3 wt%.Moreover,the addition of the MWCNTs brings about the remarkable enhancement in tensile strength and crosslink density compared with the NR host,and the data peak at 2 wt% MWCNTs loadings.When more MWCNTs are loaded,aggregations of MWCNTs are gradually generated,and the tensile strength and crosslink both decrease to a certain extent.

Synthesis and Characterization of Multi-walled Carbon Nanotube Doped Silica Aerogels

Multi-walled carbon nanotube doped silica aerogels（MWCNT-SAs） were synthesized from a wet gel of well-dispersed MWCNT by one-step solvent exchange/surface modification and ambient pressure drying（APD）. Waterglass was employed as a precursor to prepare wet gel. The content of MWCNT varied from 0 to 15% volume by wet gel. The surface group, thermal stability and microstructure of pure silica aerogel and MWCNT-SAs were investigated by FTIR, DTA, and TEM. Experimental results show that MWCNT-SAs are hydrophobic when the temperature is below 400 ℃, MWCNT-SAs exhibit a mesoporous network structure, and they achieve the largest scale with least shrinkage and lowest density when doped with 5 vol% MWCNT.

Temperature Dependent Surface Resistivity Measures of Commercial, Multiwall Carbon Nanotubes (MWCNT), and Silver Nano-Particle Doped Polyvinyl Alcohol (PVA) Films

Pure and doped Polyvinylidene difluoride (PVDF) films, for the detection of infrared radiation, have been well documented using the mechanism of pyroelectricity. Alternatively, the electrical properties of films made from Polyvinyl Alcohol (PVA) have received considerable attention in recent years. The investigation of surface resistivities of both such films, to this point, has received far less consideration in comparison to pyroelectric effects. In this research, we report temperature dependent surface resistivity measurements of commercial, and of multiwall carbon nanotubes (MWCNT), or Ag-nanoparticle doped PVA films. Without any variation in the temperature range from 22°C to 40°C with controlled humidity, we found that the surface resistivity decreases initially, reaches a minimum, but rises steadily as the temperature continues to increase. This research was conducted with the combined instrumentation of the Keithley Model 6517 Electrometer and Keithley Model 8009 resistivity test fixture using both commercial and in-house produced organic thin films. With the objective to quantify the suitability of PVDF and PVA films as IR detector materials, when using the surface resistivity phenomenon, instead of or in addition to the pyroelectricity, surface resistivity measurements are reported when considering bolometry. We found that the surface resistivity measurements on PVA films were readily implemented.

Carbon nanotubes as conducting support for potential Mn-oxide electrocatalysts： Influences of pre-treatment procedures

Different oxygen and nitrogen containing functional groups were created on the surface of the multiwalled carbon nanotubes. The multi-walled carbon nanotubes were treated in ultrasonic bath with sulfuric or nitric acid. Furthermore the surface texture was modified by increase of the roughness. In particular after treatment with the oxidizing nitric acid, in comparison to the H2SO4 or ultra-sonic treated samples,craters and edges are dominating the surface structures. Manganese oxide was deposited on the multiwalled carbon nanotubes by precipitation mechanism. Various manganese oxides are formed during the deposition process. The samples were characterized by elemental analysis, microscopy, thermal analysis,Raman spectroscopy, and by the zeta potential as well as X-ray diffraction measurements. It was shown that the deposited manganese oxides are stabilized rather by surface texture of the multi-walled carbon nanotubes than by created functional groups.

Fabrication and mechanical properties of MWCNTs-reinforced aluminum composites by hot extrusion

Over the past decade,the interest in aluminum composites reinforced with carbon nanotubes has grown significantly.Studies have been carried out to overcome problems with uniform dispersion,interfacial bonding,void formation and carbide formation of the composites.In the present work,multi-wall carbon nanotubes(MWCNTs) aluminum composites were produced.High-energy ball milling with the aim at developing well-dispersed MWCNTs Al composites was followed by cold compaction,sintering,and hot extrusion at 500 ℃.Different amounts of stearic acid as processing control agent(PCA) is used in order to minimize cold welding of the Al particles,and to produce finer particles.Differential scanning calorimetry(DSC),scanning electron microscopy(SEM),transmission electron microscopy(TEM),and X-ray diffraction(XRD) were employed to analyze the MWCNTs,the aluminum powder,and the composites’ microstructural behavior.The hardness and tensile properties of the composites are also evaluated.The results showed 500% increase in yield stress after the addition of 1 wt% MWCNTs in Al-MWCNTs based composite.The ball-milling time of 4 h is found to be sufficient as excessive milling time destroys a vast number of MWCNTs.

Preparation and Characterization of MWCNTs/E44

Epoxy resin was modified by multi-walled carbon nanotubes（MWCNTs）with an in situ method.The composite was observed using scanning electron microscopy （SEM）and X-ray diffraction （XRD）,and its abrasive wear resistance and tensile properties were tested.The results show that the function groups found on the surface of MWCNTs helped to improve the resin＇s crack resistance,and the cracks were found notably reduced in the composite.Although the resin and MWCNTs were bonded physically ,the tensile properties and wear resistance of the composite were improved notably when an optimum amount of MWCNTs were filled in Epilote-44（E44）.When 5wt pct acidified MWCNTs were filled in E44,the elastic modulus ,breaking strength and wear resistance of the composite increase to 226.7%,303.3%and 272.55%（153.29%）,respectively.

Quasi-in vivo corrosion behavior of AZ31B Mg alloy with hybrid MWCNTs-PEO/PCL based coatings

This study investigated the effects of multi-walled carbon nanotubes(MWCNTs) and polycaprolactone(PCL) on the quasi-in vivo corrosion behavior of AZ31B Mg alloy treated by plasma electrolytic oxidation(PEO). Thin(~2 μm, PCTPCL4) and thick(~60 μm, PCTPCL6) PCL layers were applied only onto the MWCNTs-PEO coating(PCT) as it showed better corrosion performance. Findings reveal that incorporation of MWCNTs induced several structural and functional modifications in the PEO coating, such as increased roughness, a thicker inner barrier layer, and reduced hydrophilicity.Quasi-in vivo corrosion testing was carried out under controlled temperature, p H, and fluid flow in simulated body fluid(SBF) by electrochemical impedance spectroscopy(EIS) and hydrogen evolution experiments. EIS results revealed that, after 48 h immersion, a diffusion process controlled hydration of the ceramic coatings. Comparison of the collected hydrogen after 15 days of immersion in the quasi-in vivo environment revealed that the PEO and PCT ceramic coatings decreased hydrogen generation by up to 74% and 91%, respectively, compared to non-coated alloy.PCTPCL6 coating exhibited the lowest amount of collected hydrogen(0.2 m L/cm^(2)). The thick PCL layer delayed the onset of substrate corrosion for at least 120 h, reducing the corrosion rate by 85% compared with the PCT.

Analysis of Bacterial Cellulose/Ionic Liquid MWCNTs via Cyclic Voltammetry

Cyclic voltammetry based on an electrochemical technique is one of the current methods that measure the developments of the electrochemical properties in biomaterial samples under conditions. Biomaterial structure was changed by conductive material while these materials caused a connective network in whole of them and was able to transfer electrons inside of biomaterials. These changes in physical and chemical properties are investigated by analysis tools such as cyclic voltammetry (CV), X-radiation (XRF) and Ultraviolet-visible spectroscopy (UV-Vis). Bacterial cellulose is biodegradable, biosynthesis of A. xylinum which is a three-dimensional nano-network structure with a distinct tunnel and pore structure. In this study, the composite process produced electrically conducting bacterial cellulose pellicles containing well-dispersed and embedded multi-walled carbon nanotubes (MWCNTs) Ionic liquids (ILs), as observed in cyclic voltammetry (CV). For this purpose, we used a special tool, called OriginLab which is an industry-leading scientific graphing and data analysis software. The cyclic voltammetry graph presents the behavior of this composite which consists of a relationship between CNT dispersion, conductivity rate and changes in bacterial cellulose structure. The electrical conductivity of the cellulose/MWCNT composite was found different with respect to CNT dispersion. It was found that the incorporation process was a useful method not only for dispersing MWCNTs-ILs in an ultrafine fibrous network structure, but also for enhancing the electrical conductivity of the polymeric membranes.

Microstructural Evolution and Oxidation Resistance of Multi-walled Carbon Nanotubes in the Presence of Silicon Powder at High Temperatures

The microstructural evolution and oxidation resistance of multi-walled carbon nanotubes （MWCNTs） by di- rectly heating silicon powder and MWCNTs in a coke bed from 1000 to 1500 ~C are investigated with the aid of X-ray diffraction （XRD）, scanning electron microscopy （SEM）, high resolution transmission electron microscopy （HRTEM） and thermogravimetry-differential scanning calorimetry （TG-DSC）. The results showed that the morphology and microstructure of MWCNTs did not change much after being treated from 1000 ~C to 1200 ~C. An obvious SiC coating was formed on the surface of MWCNTs from 1300 to 1400 ~C. Up to 1500 ~C, nearly all the MWCNTs transformed into SiC nanowires. The oxidation resistance of the treated MWCNTs was improved compared with as-received ones. Non-isothermal kinetics showed that the oxidation activation energy of the treated MWCNTs reached 208 kJ/mol, much higher than 264 k J/tool of as-received ones.

The toxicity of hydroxylated and carboxylated multi-walled carbon nanotubes to human endothelial cells was not exacerbated by ER stress inducer

Hydroxylated multi-walled carbon nanotubes(h-MWCNTs) and carboxylated MWCNTs(c-MWCNTs)have potential applications in biomedicine, but their toxicity to human endothelial cells under stressed conditions associated with chronic diseases was less studied in vitro. This study stressed human umbilical vein endothelial cells(HUVECs) with ER stress inducer thapsigargin(TG), and investigated the toxicity of h-MWCNTs and c-MWCNTs to normal and stressed HUVECs. h-MWCNTs and c-MWCNTs modestly reduced cellular viability, significantly promoted soluble ICAM-1(sICAM-1),soluble VCAM-1(sVCAM-1) as well as intracellular ROS, and decreased the expression of transcription factor KLF2 and KLF4. Pre-treatment with TG significantly reduced cellular viability, promoted IL-6 and THP-1 monocyte adhesion, and increased the expression of a panel of ER stress genes. ANOVA indicated no interaction between MWCNTs and TG pre-treatment on most of the endpoints. It was concluded that the toxicity of h-MWCNTs and c-MWCNTs to HUVECs might not be exacerbated by ER stress

Q-switched ytterbium doped fiber laser using multi-walled carbon nanotubes saturable absorber

A Q-switched ytterbium-doped fiber laser （YDFL） is proposed and demonstrated using a newly developed multi-walled carbon nanotubes polyethylene oxide （MWCNTs-PEO） film as a passive saturable absorber （SA）. The saturable absorber is prepared by mixing the MWCNTs homogeneous solution into a dilute PEO polymer solution before it is left to dry at room temperature to produce thin film. Then the film is sandwiched between two FC/PC fiber connectors and integrated into the laser cavity for Q-switching pulse generation. The laser generates a stable pulse operating at wavelength of 1060.2 nm with a threshold pump power of 53.43 mW. The YDFL generates a stable pulse train with repetition rates ranging from 7.92 to 24.27 kHz by varying 980-nm pump power from 53.42 to 65.72 mW. At 59.55-mW pump power, the lowest pulse width and the highest pulse energy are obtained at 12.18 μs and 143.5 n J, respectively.

Solar photocatalytic decomposition of two azo dyes on multiwalled carbon nanotubes(MWCNTs)/TiO_(2)composites

Multi-walled carbon nanotubes(MWCNTs)/TiO_(2)composite photocatalysts with high photoactivity were prepared by sol-gel process and further characterized by X-ray diffraction(XRD),scanning electron microscopy(SEM),Fourier transform infrared(FT-IR),and UV-vis absorption spectra.Compared to pure TiO_(2),the combination of MWCNTs with titania could cause a significant absorption shift toward the visible region.The photocatalytic performances of the MWCNTs/TiO_(2)composite catalysts were evaluated for the decomposition of Reactive light yellow K-6G(K-6G)and Mordant black 7(MB 7)azo dyes solution under solar light irradiation.The results showed that the addition of MWCNTs enhanced the adsorption and photocatalytic activity of TiO_(2)for the degradation of azo dyes K-6G and MB 7.The effect of MWCNTs content,catalyst dosage,pH,and initial dye concentration were examined as operational parameters.The kinetics of photocatalytic degradation of two dyes was found to follow a pseudo-first-order rate law.The photocatalyst was used for seven cycles with photocatalytic degradation efficiency still higher than 98%.A plausible mechanism is also proposed and discussed on the basis of experimental results.