Effect of ZrC Modified Graphite on Structure and Properties of Low-carbon Al_(2)O_(3)-C Refractories

To address the issues of reduced performance and shortened lifespan during the low-carbonizating process of Al_(2)O_(3)-C refractories,nano-crystalline ZrC modified graphite was prepared using Zr powder and flake graphite as raw materials,with NaCl and NaF mixed salt serving as the medium.The flake graphite was gradually replaced by ZrC modified graphite in the preparation of Al_(2)O_(3)-C refractories,and its impact on the material’s structure and properties was investigated.The results indicate that,compared to samples with only flake graphite,the introduction of 1 mass%to 5 mass%nano-crystalline ZrC modified graphite can significantly enhance the mechanical performance of low-carbon Al_(2)O_(3)-C refractories.When 5 mass%ZrC modified graphite is added,the mechanical properties of the samples are optimal,with the cold modulus of rupture and elastic modulus reaching 22.5 MPa and 65.0 GPa,respectively.

Exploring the impact of Nafion modifier on electrocatalytic CO_(2) reduction over Cu catalyst

Nafion as a universal polymer ionomer was widely applied for nanocatalysts electrode preparation.However,the effect of Nafion on electrocatalytic performance was often overlooked,especially for CO_(2)electrolysis.Herein,the key roles of Nafion for CO_(2)RR were systematically studied on Cu nanoparticles(NPs)electrocatalyst.We found that Nafion modifier not only inhibit hydrogen evolution reaction(HER)by decreasing the accessibility of H_(2)O from electrolyte to Cu NPs,and increase the CO_(2)concentration at electrocatalyst interface for enhancing the CO_(2)mass transfer process,but also activate CO_(2)molecule by Lewis acid-base interaction between Nafion and CO_(2)to accelerate the formation of^(*)CO,which favor of C–C coupling for boosting C_(2)product generation.Owing to these features,the HER selectivity was suppressed from 40.6%to 16.8%on optimal Cu@Nafion electrode at-1.2 V versus reversible hydrogen electrode(RHE),and as high as 73.5%faradaic efficiencies(FEs)of C_(2)products were achieved at the same applied potential,which was 2.6 times higher than that on bare Cu electrode(~28.3%).In addition,Nafion also contributed to the long-term stability by hinder Cu NPs morphology reconstruction.Thus,this work provides insights into the impact of Nafion on electrocatalytic CO_(2)RR performance.

Exact Traveling Wave Solutions to Phi-4 Equation and Joseph-Egri (TRLW) Equation and Calogro-Degasperis (CD) Equation by Modified (G'/G2)-Expansion Method

In this study, we will introduce the modified (G'/G2)-expansion method to explore some of the exact traveling wave solutions of some nonlinear partial differential equations namely, Phi-4 equation, Joseph-Egri (TRLW) equation, and Calogro-Degasperis (CD) equation. As a result, we have obtained solutions for the equations expressed in terms of trigonometric, hyperbolic and rational functions. Moreover, some selected solutions are plotted using some specific values for the parameters.

Sensitive Voltammetric Determination of Captopril Using a Carbon Paste Electrode Modified with Nano-TiO_2/Ferrocene Carboxylic Acid

A carbon paste electrode (CPE) modified with ferrocene carboxylic acid (FcCA) and TiO2 nanoparticles was constructed by incorporating TiO2 nanoparticles and ferrocene carboxylic acid into the carbon paste matrix. The electrochemical behavior of captopril (CAP) at the surface of the modified electrode was investigated using electroanalytical methods. The modified electrode showed excellent electrocatalytic activity for the oxidation of CAP in aqueous solutions at physiological pH values. Cyclic voltammetric curves showed that the oxidation of CAP at the surface of the modified electrode reduced its overpotential by more than 290 mV. The modified electrode was used for detecting captopril using cyclic voltammetry and square wave voltammetry techniques. A calibration curve in the range of 0.03 to 2400 μmol/L was obtained that had a detection limit of 0.0096 μmol/L (3?) under the optimized conditions. The modified electrode was successfully used for the determination of captopril in pharmaceutical and biological samples.

Preparation and properties of nano-TiO2 modified interior wall paint

The modification of the traditional interior wall paint was carried out by means of adding nano-TiO2 as a functional pigment. By regulating the dosage of dispersant, the nano-particles can be dispersed in paint homogeneously. With two aspects of experiments： dosage of nano-TiO2 and pigment volume concentration （PVC）, the paint formulation can be optimized and its properties~ such as hardness, scrub resistance, storage stability, contrast ratio and gloss can be improved. Finally an interior wall paint with high performance and air purification was prepared. Its character of formaldehyde degradation would be discussed in the next article.

Structure and Properties of Modified Unsaturated Polyester Resin by Nano-TiO_2

The nano-TiO2/unsaturated polyester resin (referred to as nano-TiO2/UPR hereafter) was prepared with the 'reaction method', by which a chemical bond generated between nano-TiO2 and UP was inserted in the UP long chain. The performance of the nano-TiO2/UPR was determined by such a new structure. The research results showed that the reactivity of nano-TiO2/UPR is higher than that of UPR. The impact strength and bending strength of nano-TiO2/UPR are greatly enhanced as compared with that of UPR. Thermal resistance and dielectric property of nano-TiO2/UPR are the same as that of UPR.

纳米Al_(2)O_(3)改性沥青的制备及其性能研究

为了研究纳米Al_(2)O_(3)改性剂对A-70#基质沥青物理性能、流变特性的影响及其微观改性机理。基于室内试验制备了不同掺量(1%、2%、3%、4%、5%)的纳米Al_(2)O_(3)改性沥青,对其进行三大指标、黏度、流变、抗老化性能及其傅里叶红外光谱试验测试。结果表明:加入纳米Al_(2)O_(3)之后,基质沥青的软化点和黏度提高,针入度及延度下降,纳米Al_(2)O_(3)最佳掺量为4%。由流变试验结果可知,纳米Al_(2)O_(3)可以提升基质沥青的车辙因子,显著增强其高温稳定性,抗老化性能得以提升,但对低温抗裂性能不利。根据微观分析结果,纳米Al_(2)O_(3)与基质沥青之间既产生了物理变化,又有微弱的化学反应存在。

改性TiO_(2)在光电协同下处理偶氮染料废水的研究进展

偶氮染料(AZO)是一类难被生物降解的水溶性高分子有机物,近些年来,由于良好的染色性能被广泛应用于印染等相关行业,但AZO废水一旦排入自然水体将会造成重大的环境污染问题。本文主要介绍了不同类型的改性TiO_(2)对AOZ废水的处理效果并分析了作用原理,对比分析了单一TiO_(2)与改性TiO_(2)的优缺点,积极探索改性TiO_(2)催化剂的催化机理,解析金属和非金属掺杂在其中的具体作用,为今后更加精准地控制掺杂金属或者非金属比例、提高催化剂效率提供科学依据和技术支持。

Calculation of circulation in the South China Sea during summer of 2000 by the modified inverse method

On the basis of hydrographic data obtained in August 2000 cruise, the circulation in the South China Sea (SCS) is computed by the modified inverse method in combination with SSH data from TOPEX/ERS-2 analysis. For study of the dynamical mechanism, which causes the pattern of summer circulation in the SCS, the diagnostic model (Yuan et al. 1982. Acta Oceanologica Sinica,4(1):1-11; Yuan and Su. 1992. Numerical Computation of Physical Oceanography.474-542) is used to simulate numerically the summer circulation in the SCS. The following results have been obtained. (1) The central and southwestern SCSs are dominated mainly by anticy-clonic circulation systems. They are mainly as follows. 1) There is strong anticyclonic eddy southeast of Vietnam (W1). Its horizontal scale is about 300 km, and it extends vertically from the surface to the about 1 000 m level. 2) There are a warm eddy W2 southeast of Zhongsha Islands and the anticyclonic circulation system W3 west off the Luzon Island. 3) There is a stronger cyclonic eddy C1 between the anticyclonic eddies W1 and W2.4) A strong northward coastal jet is present near the coast of Vietnam, and separates from the coast of Vietnam at about 12° N to the northeast.(2)The northern SCS is dominated mainly by a cyclonic circulation system. There is a cyclonic circulation system near and north of Section N2. (3) The southeastern SCS is dominated mainly by the cyclonic circulation system. (4) Comparing the results of circulation in the SCS during the summer of 2000 with those during the summer of 1998, it is found that they agree qualitatively, but there is the some difference between them in quantity.This shows that the circulation in the SCS has obviously seasonal feature. (5) The dynamical mechanism which products the basic pattern of summer circulation is because the following two reasons: 1) the joint effect of the baroclinity and relief (JEBAR) is essential dynamical cause; and 2) it is next important dynamical cause that the interaction between the wind stress and bottom topography under the southerly monsoon. (6) Comparing the hydrographic structure and distribution of stream functions with the SSH data from TOPEX/ERS-2 analysis in the SCS during August of 2000, they agree qualitatively.

Modified (2+1)-dimensional displacement shallow water wave system and its approximate similarity solutions

Recently, a new （2＋1）-dimensional shallow water wave system, the （2＋1）-dlmenslonal displacement shallow water wave system （2DDSWWS）, was constructed by applying the variational principle of the analytic mechanics in the Lagrange coordinates. The disadvantage is that fluid viscidity is not considered in the 2DDSWWS, which is the same as the famous Kadomtsev-Petviashvili equation and Korteweg-de Vries equation. Applying dimensional analysis, we modify the 2DDSWWS and add the term related to the fluid viscidity to the 2DDSWWS. The approximate similarity solutions of the modified 2DDSWWS （M2DDSWWS） is studied and four similarity solutions are obtained. For the perfect fluids, the coefficient of kinematic viscosity is zero, then the M2DDSWWS will degenerate to the 2DDSWWS.

Nonlocal symmetry and exact solutions of the(2+1)-dimensional modified Bogoyavlenskii–Schiff equation

In this paper,the truncated Painlev′e analysis,nonlocal symmetry,Bcklund transformation of the（2＋1）-dimensional modified Bogoyavlenskii–Schiff equation are presented.Then the nonlocal symmetry is localized to the corresponding nonlocal group by the prolonged system.In addition,the（2＋1）-dimensional modified Bogoyavlenskii–Schiff is proved consistent Riccati expansion（CRE） solvable.As a result,the soliton–cnoidal wave interaction solutions of the equation are explicitly given,which are difficult to find by other traditional methods.Moreover figures are given out to show the properties of the explicit analytic interaction solutions.

Catalytic Oxidation of Dimethyl Ether to Dimethoxymethane over Cs Modified H_3PW_(12)O_(40)/SiO_2 Catalysts

The attractive utilization route for one-step catalytic oxidation of dimethyl ether to dimethoxymethane was successfully carried out over the H3PW12O40（40%）/SiO2 catalyst, modified by Cs, K, Ni, and V. The Cs modification of H3PW12O40（40%）/SiO2 gave the most promising result of 20% dimethyl ether conversion and 34.8% dimethoxymethane selectivity. Dimethoxymethane could be synthe- sized via methoxy groups decomposed from dimethyl ether through the synergistic effect between the acid sites and the redox sites of Cs modified H3PW12O40（40%）/SiO2.

Electrochemical determination of vitamin C in the presence of uric acid by a novel TiO_2 nanoparticles modified carbon paste electrode

The electrochemical behavior of vitamin C（ascorbic acid or AA） is investigated on the surface of a carbon-paste electrode modified with TiO2 nanoparticles and 2,2＇-（1,2 butanediylbis（nitriloethylidyne））-bis-hydroquinone（BBNBH）.The prepared modified electrode showed an efficient catalytic role in the electrochemical oxidation of AA,leading to remarkable decrease in oxidation overpotential and enhancement of the kinetics of the electrode reaction.This modified electrode exhibits well-separated oxidation peaks for AA and uric acid（UA）.The modified electrode is successfully applied for the accurate determination of AA in pharmaceutical preparations.

Preparation of Calcium Cross-linked Nano-Fe3O4 Modified Zeolite Microspheres for Cu^2+ Adsorption from Wastewater

Artificial zeolite was modified by nano-Fe3O4 for development of functional adsorbents.Subsequently,adsorbents such as calcium cross-linked nano-Fe3O4 microspheres (Ca-MS),calcium cross-linked nano-Fe3O4 modified zeolite microspheres (Ca-MZS) and iron cross-linked nano-Fe3O4 modified zeolite microspheres (Fe-MZS) were prepared and compared for their adsorption performance.The effects of adsorbent dosage,solution pH,initial concentration and ion content on the removal of Cu^2+ from wastewater are investigated,and the adsorption kinetics and isotherms for the adsorbent materials were analyzed.The experimental results indicate that for the initial concentration of Cu^2+ of 30 mg/L,the adsorption is noted to be most stable.The optimal initial pH for adsorbing Cu^2+ is observed to be 5.5.At an optimal dosage of Ca-MZS of 900 mg/L,the adsorption capacity is measured to be 28.25 mg/g,along with the removal rate of 72.49%.The addition of Na+ and K+ affects the adsorption of Cu^2+.For the Na^+ and K^+ concentration of 0.2 mmol/L,the Cu^2+ removal rate by Ca-MZS drops to 11.94% and 22.12%,respectively.As compared with the adsorbents such as Natural Zeolite (NZ),Ca-MS and Fe-MZS,Ca-MZS demonstrates the best removal effect in solution,where the removal rate reaches 84.27%,with the maximum adsorption capacity of 28.09 mg/g.The Cu^2+ adsorption kinetics of Ca-MZS is observed to follow the Elovich kinetic model,with the adsorption isotherm data fitting the Freundlich isotherm model by using the non-linear method.

Formation of TiO2 Modified Film on Carbon Steel

A new technique for preparing TiO2 modified film on carbon steel was accomplished by electroless plating and sol-gel composite process. The artificial neural network was applied to optimize the preparing condition of TiO2 modified film. The optimized condition for forming TiO2 modified film on carbon steel was that NiP plating for 50 min, dip-coating times as 4, heat treatment time for 2 h, and the molar ratio of complexing agent and Ti(OC4HZ9)4 kept 1.5:1. The results showed that TiO2 modified film have good corrosion resistance. The result conformed that it is feasible to design the preparing conditions of TiO2 modified film by artificial neural network.

Satisfactory surgical outcome of T2 gastric cancer after modified D2 lymphadenectomy

Objective： Though D2 lymphadenectomy has been increasingly regarded as standard surgical procedure for advanced gastric cancer （GC）, the modified D2 （D 1＋7, 8a and 9） lymphadenectomy may be more suitable than D2 dissection for T2 stage GC. The purpose of this study is to elucidate whether the surgical outcome of modified D2 lymphadenectomy was comparable to that of standard D2 dissection in T2 stage GC patients. Methods： A retrospective cohort study with 77 cases and 77 controls matched for baseline characteristics was conducted. Patients were categorized into two groups according to the extent of lymphadenectomy： the modified D2 group （roD2） and the standard D2 group （D2）. Surgical outcome and recurrence date were compared between the two groups. Results： The 5-year overall survival （OS） rate was 71.4% for patients accepted mD2 lymphadenectomy and 70.1% for those accepted standard D2, respectively, and the difference was not statistically significant. Multivariate survival analysis revealed that curability, tumor size, TNM stage and postoperative complications were independently prognostic factors for T2 stage GC patients. Patients in the mD2 group tended to have less intraoperative blood loss （P=0.001） and shorter operation time （P〈0.001） than those in the D2 group. While there were no significant differences in recurrence rate and types, especially lymph node recurrence, between the two groups. Conclusions： The surgical outcome of mD2 lymphadenectomy was equal to that of standard D2, and the use of mD2 instead of standard D2 can be a better option for T2 stage GC.

Vacancies and Antisites in B2 FeAl and DO_3 Fe_3Al with a Modified Analytic EAM Model

A simple modified analytic EAM model for bcc Fe and fcc Al was used to calculate the lattice constant and elastic constants of B2 FeAl and DO3 Fe3Al alloys. The formation energies of vacancy and antisite were also calculated. The present calculations are in agreement with the experimental data and the theoretical results obtained by other authors.

Solving (2+1)-dimensional sine-Poisson equation by a modified variable separated ordinary differential equation method

By introducing a more general auxiliary ordinary differential equation （ODE）, a modified variable separated ordinary differential equation method is presented for solving the （2 ＋ 1）-dimensional sine-Poisson equation. As a result, many explicit and exact solutions of the （2 ＋ 1）-dimensional sine-Poisson equation are derived in a simple manner by this technique.

Improved Stability and Shape Selectivity of 2,6-Dimethylnaphthalene by Methylation of Naphthalene with Methanol on Modified Zeolites

2,6-Dimethylnaphthalene (2,6-DMN) is a key intermediate for polyethylene naphthalate synthesis. The selective synthesis of 2,6-DMN from naphthalene and methanol was carried out over different zeolites (HZSM-5, Hβ, HUSY and SAPO-11) modified by 0.1wt% PdO under atmospheric pressure. Among the adopted zeolites, SAPO-11 exhibits exceptional shape-selectivity and stability to synthesize 2,6-dimethylnaphthalene from methylation of naphthalene, due to the special pore structure of SAPO-11 which inosculated better with 2,6-dimethylnaphthalene than with 2,7-dimethylnaphthalene.