Sr含量对Al-Si合金显微组织和热导率的影响

以纯铝、Al-20Si和Al-10Sr中间合金为原料,Sr为变质剂(含量为0.01%、0.02%、0.04%和0.06%,质量分数),制备了Al-7Si-xSr、Al-12Si-xSr和Al-20Si-xSr合金,研究了Sr含量对Al-Si合金相变储热材料显微组织及热导率的影响。利用Hot Disk热常数分析仪测量合金的热导率,通过扫描电镜观察及分析合金的显微组织。结果表明:在Al-Si合金中添加变质元素Sr会影响合金的热导率,Al-7Si-0.04Sr合金热导率较Al-7Si合金增加了73.47 W·m^(-1)·K^(-1),Al-20Si-0.04Sr合金的热导率较Al-20Si合金增加了24.09 W·m^(-1)·K^(-1),Al-12Si-0.04Sr合金的热导率较Al-12Si合金增加了17.79 W·m^(-1)·K^(-1)。铝硅合金热导率的增长主要与α(Al)、共晶硅和初晶硅的形貌有关。经过Sr变质之后,Al-7Si合金中共晶Si立体形貌均由片层状转变为珊瑚状,Al-12Si和Al-20Si合金中共晶Si立体形貌由片层状转变为枝条状;其中,Al-7Si合金中α(Al)尺寸明显减少、排列紧密,二次枝晶臂间距逐渐减小;Al-20Si合金中的初晶Si尺寸明显减小,其形貌由多角的大块状变为小块状;α(Al)形态的转变不仅能够为自由电子的传输提供快速通道,而且还会使得共晶Si的排列更加规则,减少自由电子发生散射的几率,对合金的热导率影响较大。共晶Si由片层状转变为珊瑚状或枝条状,增加电子的平均自由程,有利于电子的传输。Al-20Si合金的热导率与初晶Si的形态有着重要联系,大尺寸且形状完整的初晶Si会发生晶格振动,会提高合金的热导率。

Al-Si镀层22MnB5激光焊的熔池流动特性及元素分布

熔池流动行为对镀层元素在焊缝中的分布起决定性作用.采用建立激光焊熔池三维瞬态数值模型的方法,分析AlSi镀层22MnB5高强度钢激光焊的熔池流动行为及其对焊缝中Al元素分布的影响规律.在焊接试验中,根据能谱仪对焊接接头的扫描数据验证数值模型的可靠性.结合模拟结果与试验结果对激光焊熔池流动行为及焊缝Al元素分布规律进行研究.结果表明,根据激光焊热输入与功率密度阈值的不同,熔池形貌呈现无匙孔、未完全贯穿匙孔和完全贯穿匙孔3种特征,并存有不同的温度场、流场、流速和稳定性.无匙孔熔池由于流速分布均匀,涡流产生较少,稳定性最好.镀层Al元素在焊接接头上下焊趾区域易产生偏聚,较之上表面镀层,下表面镀层进入熔池后Al元素偏聚现象更明显.因此,上部Al元素均质化分布显著优于下部.

SiCp/Al-Si基复合材料界面结构调控及强化机制的研究进展

SiCp/Al-Si基复合材料具有高的比强度、比刚度、比模量,良好的导热、导电、耐磨性及尺寸稳定性等优点,作为结构功能性材料应用于空间工程、电子封装、交通运输和精密仪器等领域。其研究热点主要集中在界面结构调控、强化机制及性能调控等方面。在SiCp/Al-Si复合材料中存在着增强体与基体界面、析出相与基体界面、析出相与增强体界面,这些界面受各种因素影响,会出现多种界面反应和界面产物,界面结构和结合状态复杂而多样。基于此,本文综述了制备工艺、基体合金成分和SiCp表面改性等方面对SiCp/Al-Si基复合材料界面结构的影响及调控,并总结了影响其力学性能的因素及强化机制的研究现状,最后对复合材料未来的发展及研究方向进行了展望。

Dynamic simulation analysis of molten salt reactor-coupled air-steam combined cycle power generation system

A nonlinear dynamic simulation model based on coordinated control of speed and flow rate for the molten salt reactor and combined cycle systems is proposed here to ensure the coordination and stability between the molten salt reactor and power system.This model considers the impact of thermal properties of fluid variation on accuracy and has been validated with Simulink.This study reveals the capability of the control system to compensate for anomalous situations and maintain shaft stability in the event of perturbations occurring in high-temperature molten salt tank outlet parameters.Meanwhile,the control system’s impact on the system’s dynamic characteristics under molten salt disturbance is also analyzed.The results reveal that after the disturbance occurs,the controlled system benefits from the action of the control,and the overshoot and disturbance amplitude are positively correlated,while the system power and frequency eventually return to the initial values.This simulation model provides a basis for utilizing molten salt reactors for power generation and maintaining grid stability.

Si含量对Al-Si-Cu-Ni-Mg合金组织和性能的影响

采用搅拌铸造工艺制备不同Si含量合金,旨在揭示Si含量对Al-Si-Cu-Ni-Mg合金微观组织、力学性能和耐磨性的影响。结果表明,随着Si含量升高,合金中共晶Si长径比和平均长度先升高后降低,Si含量为16wt.%合金的长径比和平均长度最大,分别为8.8μm、24.1μm。经过520℃/6 h固溶+180℃/5 h时效处理后,共晶Si形貌由纤维状变为球状,初晶Si棱角钝化。合金中共晶Si长径比和平均长度均有明显降低,保持与铸态合金相同的变化趋势;Si含量为16wt.%合金的长径比和平均长度分别为3.5μm、12.4μm,初晶Si尺寸没有明显变化。随着Si含量的升高,铸态合金拉伸性能逐渐降低,宏观硬度逐渐上升。经过T6热处理后,合金的拉伸性能和宏观硬度有了明显提升,保持与铸态合金相同的变化趋势,随着Si含量的升高,合金磨损失重减少,耐磨性得到改善。Si含量为16wt.%的合金磨损失重最少,耐磨性最好;继续增加Si含量时,合金耐磨性降低。

固溶处理对铸造Al-Si合金相选择再结晶的影响

相选择再结晶在Al-Si合金中基于应变分配原理实现对软相进行再结晶、硬相进行回复从而球化硅相和细化铝相。相选择再结晶处理后合金呈现出高的加工硬化率和伸长率。固溶处理是实现铝合金强韧化的重要环节,与相选择再结晶互相影响。一方面,初始组织对相选择再结晶的应变分配有一定影响;另一方面铝合金固溶过程会影响析出强化作用。因此,本文探究铸造Al-7Si-0.65Mg合金固溶过程中共晶硅相的形貌对相选择再结晶的影响,结合时效析出实现合金的强韧化。结果表明,0.5 h短时间固溶处理可以保持相选择再结晶合金中清晰且不分散的共晶硅颗粒骨架状结构,同时增加基体中Si和Mg含量促进强化相Mg2Si析出,使合金屈服强度达到300 MPa,断后伸长率为9.5%,显著优于传统T6态。

Mn元素对Al-Si合金富铁相析出影响的热力学计算

本研究选取不同Mn元素含量的Al-7 wt%Si-0.2 wt%Fe铝液为研究对象,利用热力学软件定量计算了Mn元素添加量对铝液Scheil-Gulliver冷却凝固过程的析出相。结果表明:不同Mn元素含量的铝液冷却过程中相转变顺序有所不同,添加一定量的Mn元素可利于铝液凝固过程中析出Al3MnSi2相;添加Mn元素并不会大幅减少完全凝固后β-AlFeSi相的质量比,且不同Mn元素含量的铝合金中β-AlFeSi相质量比相差不超过1%,说明难以通过添加Mn元素来减少铝液完全凝固后的β-AlFeSi相质量比;铝液凝固末期,β-AlFeSi与Al3MnSi2发生共晶反应,Al3MnSi2对β-AlFeSi的形貌可能具有改性作用,是β-AlFeSi与Al3MnSi2的共晶相呈现出不规则形状的主要原因。

Growth kinetics of titanium carbide coating by molten salt synthesis process on graphite sheet surface

The synthesis of carbide coatings on graphite substrates using molten salt synthesis(MSS),has garnered significant interest due to its cost-effective nature.This study investigates the reaction process and growth kinetics involved in MSS,shedding light on key aspects of the process.The involvement of Ti powder through liquid-phase mass transfer is revealed,where the diffusion distance and quantity of Ti powder play a crucial role in determining the reaction rate by influencing the C content gradient on both sides of the carbide.Furthermore,the growth kinetics of the carbide coating are predominantly governed by the diffusion behavior of C within the carbide layer,rather than the chemical reaction rate.To analyze the kinetics,the thickness of the carbide layer is measured with respect to heat treatment time and temperature,unveiling a parabolic relationship within the temperature range of 700-1300℃.The estimated activation energy for the reaction is determined to be 179283 J·mol^(-1).These findings offer valuable insights into the synthesis of carbide coatings via MSS,facilitating their optimization and enhancing our understanding of their growth mechanisms and properties for various applications.

Etching Mechanism of Ti_(3)C_(2)Cl_(2) MXene Phases by CuCl_(2)-Lewis Molten Salt Method

We described a method for obtaining fluorine-free Ti_(3)C_(2)Cl_(2)MXene phases by melting copper in CuCl_(2)instead of aluminum in Ti_(3)AlC_(2).XRD results show that when molten salt CuCl_(2)etches Ti_(3)AlC_(2),it forms an intermediate product Ti_(3)CuC_(2),and then reacts with Ti_(3)CuC_(2)to obtain Ti_(3)C_(2)Cl_(2).The reaction of Ti_(3)AlC_(2)and CuCl_(2)at a temperature of 800℃for 2 h to obtain Ti_(3)C_(2)Cl_(2)with an optimal lamellar structure is shown in SEM results.The pseudopotential plane-wave(PP-PW)method is used to calculate on the electronic structure.The etching mechanism is investigated by the total energies of each substance.The chemical reaction of Ti_(3)AlC_(2)and CuCl_(2)will first become Ti_(3)CuC_(2)and Cu,and then become Ti_(3)C_(2)Cl_(2)during the Lewis acid etching process,which are consistent with the experimental results.

Preliminary safety analysis for heavy water-moderated molten salt reactor

The heavy water-moderated molten salt reactor(HWMSR)is a newly proposed reactor concept,in which heavy water is adopted as the moderator and molten salt dissolved with fissile and fertile elements is used as the fuel.Issues arising from graphite in traditional molten salt reactors,including the positive temperature coefficient and management of highly radio-active spent graphite waste,can be addressed using the HWMSR.Until now,research on the HWMSR has been centered on the core design and nuclear fuel cycle to explore the viability of the HWMSR and its advantages in fuel utilization.However,the core safety of the HWMSR has not been extensively studied.Therefore,we evaluate typical accidents in a small modular HWMSR,including fuel salt inlet temperature overcooling and overheating accidents,fuel salt inlet flow rate decrease,heavy water inlet temperature overcooling accidents,and heavy water inlet mass flow rate decrease accidents,based on a neutronics and thermal-hydraulics coupled code.The results demonstrated that the core maintained safety during the investigated accidents.

Effect of slow shot speed on externally solidified crystal,porosity and tensile property in a newly developed high-pressure die-cast Al-Si alloy

The effect of slow shot speed on externally solidified crystal(ESC),porosity and tensile property in a newly developed high-pressure die-cast Al-Si alloy was investigated by optical microscopy(OM),scanning electron microscopy(SEM)and laboratory computed tomography(CT).Results showed that the newly developed AlSi9MnMoV alloy exhibited improved mechanical properties when compared to the AlSi10MnMg alloy.The AlSi9MnMoV alloy,which was designed with trace multicomponent additions,displays a notable grain refining effect in comparison to the AlSi10MnMg alloy.Refining elements Ti,Zr,V,Nb,B promote heterogeneous nucleation and reduce the grain size of primaryα-Al.At a lower slow shot speed,the large ESCs are easier to form and gather,developing into the dendrite net and net-shrinkage.With an increase in slow shot speed,the size and number of ESCs and porosities significantly reduce.In addition,the distribution of ESCs is more dispersed and the net-shrinkage disappears.The tensile property is greatly improved by adopting a higher slow shot speed.The ultimate tensile strength is enhanced from 260.31 MPa to 290.31 MPa(increased by 11.52%),and the elongation is enhanced from 3.72%to 6.34%(increased by 70.52%).

Electrochemical behavior of Fe(Ⅲ)in Na_(2)SiO_(3)-SiO_(2)-Fe_(2)O_(3)molten salt

The high-temperature requirement for liquid iron smelting via molten oxide electrolysis presents significant challenges.This study investigates the electrochemical reduction of Fe(Ⅲ)in a novel low-temperature electrolyte,Na_(2)SiO_(3)-SiO_(2)-Fe_(2)O_(3),utilizing cyclic voltammetry and square wave voltammetry techniques.The results show that Fe(Ⅲ)reduction occurs in two steps:Fe(Ⅲ)+e^(−)→Fe(Ⅱ),Fe(Ⅱ)+2e^(−)→Fe,and that the redox process of Fe(Ⅲ)/Fe(Ⅱ)at the tungsten electrode is an irreversible reaction controlled by diffusion.The diffusion coefficients of Fe(Ⅲ)in the molten Na_(2)SiO_(3)-SiO_(2)-Fe_(2)O_(3)in the temperature range of 1248–1278 K are between 1.86×10^(−6)cm^(2)/s and 1.58×10^(−4)cm^(2)/s.The diffusion activation energy of Fe(Ⅲ)in the molten salt is 1825.41 kJ/mol.As confirmed by XRD analysis,potentiostatic electrolysis at−0.857 V(vs.O_(2)/O_(complex)^(2-))for 6 h produces metallic iron on the cathode.

Multidisciplinary treatment of molten aluminum combined burn:An unusual case report

Molten aluminum is among the most common causes of burns in the metal industry.However,only few reports are available on molten aluminum injuries.Herein,we report an unusual case of molten aluminum burn.The patient had burns not only on the body surface but also in the respiratory tract and esophagus,adding to the difficulty of treatment.Multidisciplinary consultation and cooperation led to the development of a treatment plan for the patient,which included tracheotomy,respiratory management,endoscopic therapy,infection control,and psychological support.To our knowledge,this is the first report of molten aluminum-induced burns involving the face,neck,respiratory tract,esophagus,and eyes.We also describe our experience with multidisciplinary treatment for the management of molten aluminum burns.

A general descriptor for guiding the electrolysis of CO_(2)in molten carbonate

Molten carbonate is an excellent electrolyte for the electrochemical reduction of CO_(2)to carbonaceous materials.However,the electrolyte–electrode-reaction relationship has not been well understood.Herein,we propose a general descriptor,the CO_(2)activity,to reveal the electrolyte–electrode-reaction relationship by thermodynamic calculations and experimental studies.Experimental studies agree well with theoretical predictions that both cations(Li^(+),Ca^(2+),Sr^(2+)and Ba^(2+))and anions(BO_(2)^(-),Ti_(5)O_(14)^(8-),SiO_(3)^(2-))can modulate the CO_(2)activity to control both cathode and anode reactions in a typical molten carbonate electrolyzer in terms of tuning reaction products and overpotentials.In this regard,the reduction of CO_(3)^(2-)can be interpreted as the direct reduction of CO_(2)generated from the dissociated CO_(3)^(2-),and the CO_(2)activity can be used as a general descriptor to predict the electrode reaction in molten carbonate.Overall,the CO_(2)activity descriptor unlocks the electrolyte–electrode-reaction relationship,thereby providing fundamental insights into guiding molten carbonate CO_(2)electrolysis.

Molten salt construction of core-shell structured S-scheme CuInS_(2)@CoS_(2) heterojunction to boost charge transfer for efficient photocatalytic CO_(2) reduction

Weak redox ability and severe charge recombination pose significant obstacles to the advancement of CO_(2) photoreduction.To tackle this challenge and enhance the CO_(2) photoconversion efficiency,fabricating well-matched S-scheme heterostructure and establishing a robust built-in electric field emerge as pivotal strategies.In pursuit of this goal,a core-shell structured CuInS_(2)@CoS_(2)S-scheme heterojunction was meticulously engineered through a two-step molten salt method.This approach over the CuInS_(2)-based composites produced an internal electric field owing to the disparity be-tween the Fermi levels of CoS_(2) and CuInS_(2) at their interface.Consequently,the electric field facili-tated the directed migration of charges and the proficient separation of photoinduced carriers.The resulting CuInS_(2)@CoS_(2) heterostructure exhibited remarkable CO_(2) photoreduction performance,which was 21.7 and 26.5 times that of pure CuInS_(2) and CoS_(2),respectively.The S-scheme heterojunc-tion photogenerated charge transfer mechanism was validated through a series of rigorous anal-yses,including in situ irradiation X-ray photoelectron spectroscopy,work function calculations,and differential charge density examinations.Furthermore,in situ infrared spectroscopy and density functional theory calculations corroborated the fact that the CuInS_(2)@CoS_(2) heterojunction substan-tially lowered the formation energy of *COOH and *CO.This study demonstrates the application potential of S-scheme heterojunctions fabricated via the molten salt method in the realm of ad-dressing carbon-related environmental issues.

Plutonium utilization in a small modular molten-salt reactor based on a batch fuel reprocessing scheme

A molten salt reactor(MSR)has outstanding features considering the application of thorium fuel,inherent safety,sustainability,and resistance to proliferation.However,fissile material^(233)U is significantly rare at the current stage,thus it is difficult for MSR to achieve a pure thorium-uranium fuel cycle.Therefore,using plutonium or enriched uranium as the initial fuel for MSR is more practical.In this study,we aim to verify the feasibility of a small modular MSR that utilizes plutonium as the starting fuel(SM-MSR-Pu),and highlight its advantages and disadvantages.First,the structural design and fuel management scheme of the SM-MSR-Pu were presented.Second,the neutronic characteristics,such as the graphite-irradiation lifetime,burn-up performance,and coefficient of temperature reactivity were calculated to analyze the physical characteristics of the SM-MSR-Pu.The results indicate that plutonium is a feasible and advantageous starting fuel for a SM-MSR;however,there are certain shortcomings that need to be solved.In a 250 MWth SM-MSR-Pu,approximately 288.64 kg^(233)U of plutonium with a purity of greater than 90% is produced while 978.00 kg is burned every ten years.The temperature reactivity coefficient decreases from -4.0 to -6.5 pcm K^(-1) over the 50-year operating time,which ensures a long-term safe operation.However,the amount of plutonium and accumulation of minor actinides(MAs)would increase as the burn-up time increases,and the annual production and purity of^(233)U will decrease.To achieve an optimal burn-up performance,setting the entire operation time to 30 years is advisable.Regardless,more than 3600 kg of plutonium eventually accumulate in the core.Further research is required to effectively utilize this accumulated plutonium.

Temperature Drop of Molten Metals in Open Channels

The temperature drop of molten metal flowing in open channels is numerically determined. Rectangular, trapezoidal and triangular geometries are considered. The overall heat transfer coefficients for the bottom, side walls and free surface of the channel have been taken from the literature. For each geometry, the volumetric flow rate, mean residence time and temperature drop as a function of the channel inclination angle were determined. The rectangular and trapezoidal geometries present the smallest temperature drops, while the triangular geometry presents the greatest temperature drop. The factors that most affect this drop are the value of the free surface area of the channel, and the average residence time of the molten metal in the channel.

Al-Si合金大型薄壁铸件抗变形工艺研究

使用Novacast软件模拟了铸件充型和凝固过程,采用3DP砂型打印机生产砂芯,在差压设备炉中进行熔炼浇注。由于舱体内部无凸台及环筋,在铸造及热处理过程中容易发生热变形,针对该问题修改工艺方案,在舱体外表面增加防变形环,防止铸件整体发生扭曲,对铸件增加防变形环状态进行模拟仿真,确保铸件内部质量符合要求,增加防变形工装后,内腔尺寸变形量控制在±0.5 mm,铸件尺寸得到保证,解决了该大型薄壁铝硅合金铸件铸造及热处理变形问题。

Effect of the Density of Molten Metal on the Raining Phenomenon in Horizontal Centrifugal Casting

In this work the influence of the density of the molten metal on the emergence of the raining phenomenon in the horizontal centrifugal casting process is numerically studied. Transient 2D numerical simulations were carried out using Computational Fluid Dynamics software. Three molten metals with different density, namely aluminum, iron and lead, and three angular frequencies, namely 50, 66 and 77 rad/s were considered. It is found that the density of the molten metal significantly affects the emergence, transient or permanent, of the rain phenomenon. However, the magnitude and duration of the rain phenomenon depend on the angular frequency of the rotating mold. Likewise, since gravitational forces affect the metal according to its density, the value of the critical rotation speed of the mold is also affected.

Design and Application of Intelligent Control System for Molten Iron Transportation Based on 5G Technology

Molten transport is an important link in the iron and steel enterprise production,involves many complex factors,artificial management is difficult.Therefore,puts forward a kind of molten iron transport wisdom control system based on 5G technology,which mainly contains the intelligent identification tracking system,equipment status collection information acquisition system,locomotive vehicle terminal system,etc.Combined with the analysis of the actual application situation,the system could integrate all the processes and elements of molten iron produc-tion and transportation,realize the integration of operation and management,and also promote the improvement of the turnover efficiency of molten iron tank,reduce the demand for personnel,and reduce the labor cost.