Carbon dioxide reforming of methane on monolithic Ni/Al_2O_3-based catalysts

Nickel-alumina catalysts supported on cordierite monoliths of honeycomb structure surpass essentially the conventional granulated ones with respect to the output in carbon dioxide reforming of methane. Adjusting the surface acid-base properties of catalysts by introduction of alkali metal （Na, K） oxides inhibits the carbonization and as a result, improves the operational stability of these catalysts. An effect of promotion of nickel-alumina based composite doped by lanthanum oxide is found. This effect, caused by an additional route for the CO2 activation on Ni-La2O3/Al2O3/cordierite catalyst, is displayed in increase of methane conversion under conditions of an oxidant excess.

Monolithic Mesh-Type Fe-Pd/γ-Al₂O₃/Al Bifunctional Catalysts for Electro-Fenton Degradation of Rhodamine B

A novel Fe-Pd bifunctional catalyst supported on mesh-type γ-Al2O3/Al was prepared and applied in the degradation of Rhodamine B (RhB). The monolithic mesh-type Fe-Pd/γ-Al2O3/Al bifunctional catalyst could be separated from the solution directly and could synthesize H2O2 in situ. The characterization results showed that Fe could improve the dispersion of Pd0, and the electronic interactions between Pd and Fe could increase the Pd0 contents on the catalyst, which increased the productivity of H2O2. Furthermore, DFT calculations proved that the addition of Fe could inhibit the dissociation of O2 and promote the nondissociative hydrogenation of O2 on the surface of Fe-Pd/γ-Al2O3/Al, which resulted in the increasement of H2O2 selectivity. Finally, the in-situ synthesized H2O2 by Pd was furtherly decomposed in situ by Fe to generateOH radicals to degrade organic pollutants. Therefore, Fe-Pd/ γ-Al2O3/Al catalysts exhibited excellent catalytic activity in the in-situ synthesis of H2O2 and the degradation of RhB due to the synergistic effects between Pd and Fe on the catalyst. It provided a new idea for the design of bifunctional electro-Fenton catalysts. Ten cycles of experiments showed that the catalytic activity of Fe-Pd/γ-Al2O3/Al catalyst could be maintained for a long time.

Effect of Fe_2O_3 Loading Amount on Catalytic Properties of Monolithic Fe_2O_3/Ce_(0.67)Zr_(0.33)O_2-Al_2O_3 Catalyst for Methane Combustion

Ce0.67Zr0.33O2-Al2O3 solid solution was prepared by the co-precipitation method. Fe2O3-based catalysts supported on the solid solution were obtained by the impregnation method. The article revealed that the optimal loading amount of Fe2O3 on Ce0.67Zr0.33 O2-Al2O3 in our experimental condition for catalytic combustion of methane was 8% （ mass fraction）. The prepared catalysts were characterized by BET, TPR, XRD analyses, and their catalytic activity was investigated after being calcined at 873 K and after being aged in water gas at 1273 K. When the loading amount of Fe203 was 8% （ mass fraction）, the catalyst held the highest activity, and the best temperature speciality and thermal stability. The complete-conversion temperature of methane for fresh and aged sample was 788 and 838 K, respectively. The range between the light-off temperature and the complete-conversion temperature was only 15 K. The characterization results of XRD indicated that Fe2O3 was well dispersed on the Ce0.67Zr0.33O2-Al2O3 matrix. The results of BET and TPR were in good harmony with the catalytic activity results.

Enhanced CO oxidation over potassium-promoted Pt/Al_2O_3 catalysts:Kinetic and infrared spectroscopic study

A series of K-promoted Pt/Al2O3 catalysts were tested for CO oxidation. It was found that the addition of K significantly enhanced the activity. A detailed kinetic study showed that the activation energies of the K-containing catalysts were lower than those of the K-free ones, particularly for catalysts with high Pt contents （51.6 k）/mol for 0.42K-2.0Pt/Al2O3 and 6：3.6 kJ/mol for 2.0Pt/Al2O3 ）. The CO reaction orders were higher for the K-containing catalysts （about -0.2） than for the K-free ones （about -0.5）, with the former having much lower equilibrium constants for CO adsorption than the latter. In situ Fourier-transform infrared spectroscopy showed that surface CO desorption from the 0.42K-2.0Pt/Al2O3 catalyst was easier than from 2.0Pt/Al2O3. The promoting effect of K was therefore caused by weakening of the interactions between CO and surface Pt atoms. This decreased coverage of the catalyst with CO and facilitated competitive O2 chemisorption on the Pt surface, and significantly lowered the reaction barrier between chemisorbed CO and O2 species.

Methanation of syngas over coral reef-like Ni/Al_2O_3 catalysts

Coral reef-like Ni/Al2O3 catalysts were prepared by co-precipitation of nickel acetate and aluminium nitrate with sodium carbonate aqueous solution in the medium of ethylene glycolye.Methanation of syngas was carried out over coral reef-like Ni/Al2O3 catalysts in a continuous flow type fixed-bed reactor.The structure and properties of the fresh and used catalysts were studied by SEM,N2 adsorption-desorption,XRD,H2-TPR,O2-TPO,TG and ICP-AES techniques.The results showed that the coral reef-like Ni/Al2O3 catalysts exhibited better activity than the conventional Ni/Al2O3-H2O catalysts.The activities of coral reef-like catalysts were in the order of Ni/Al2O3-673Ni/Al2O3-573Ni/Al2O3- 473Ni/Al2O3-773.Ni/Al2O3-673-EG catalyst showed not only good activity and improved stability but also superior resistance to carbon deposition,sintering,and Ni loss.Under the reaction conditions of CO/H2（molar ratio）=1：3,593 K,atmospheric pressure and a GHSV of 2500 h-1,CH4 selectivity was 84.7%,and the CO conversion reached 98.2%.

Investigation of the characteristics and deactivation of catalytic active center of Cr-Al_2O_3 catalysts for isobutane dehydrogenation

Deactivation mechanism of Cr-Al2O3catalyst and the interaction of Cr-A1 in the dehydrogenation of isobutane, as well as the nature of the catalytic active center, were studied using XRD, SEM, XPS, H2-TPR, isobutane-TPR and TPO techniques. The results revealed that the deactivation of Cr-Al2O3 catalyst was mainly caused by carbon deposition on its surface. The Cr3＋ ion could not be reduced by hydrogen but could be reduced to Cr2＋ by hydrocarbons and monoxide carbon. The active center for isobutane dehydrogenation could be Cr2＋/Cr3＋ produced from Cr6＋ by the on line reduction of hydrocarbon and carbon monoxide. The binding energy of Al3＋ was strongly affected by the state of chromium cations in the catalysts.

Ethanol steam reforming over Ni-Cu/Al_2O_3-M_yO_z (M = Si, La, Mg,and Zn) catalysts

Ni-based catalysts doped with copper additives were studied on their role in ethanol steam reforming reaction. The effects of Cu content, support species involving Al2O3-SIO2, Al2O3-MgO, Al2O3-ZnO, and Al2O3-La2O3, on the catalytic performance were studied. Characterizations by TPR, XRD, NH3-TPD, XPS, and TGA indicated that catalysts 30Ni5Cu/Al2O3-MgO and 30Ni5Cu/Al2O3-ZnO have much higher H2 selectivity than 30Ni5Cu/Al2O3-SiO2, as well as good coke resistance. H2 selectivity for 30Ni5Cu/Al2O3-MgO catalyst was 73.3% at 450 ℃ and increased to 94.0% at 600℃, whereas for 30Ni5Cu/Al2O3-ZnO catalyst, the H2 selectivity was 63.6% at 450 ℃ and 95.2% at 600℃. TheseAl2O3-MgO and Al2O3-ZnO supported Ni-Cu bimetallic catalysts may have important applications in the production of hydrogen by ethanol steam reforming reactions.

Effect of Al_2O_3 Binder on the Precipitated Iron-Based Catalysts for Fischer-Tropsch Synthesis

A series of iron-based Fischer-Tropsch synthesis （FTS） catalysts incorporated with Al2O3 binder were prepared by the combination of co-precipitation and spray drying technology. The catalyst samples were characterized by using N2 physical adsorption, temperature-programmed reduction/desorption （TPR/TPD） and MSssbauer effect spectroscopy （MES） methods. The characterization results indicated that the BET surface area increases with increasing Al2O3 content and passes through a maximum at the Al2O3/Fe ratio of 10/100 （weight basis）. After the point, it decreases with further increase in Al2O3 content. The incorporation of Al2O3 binder was found to weaken the surface basicity and suppress the reduction and carburization of iron-based catalysts probably due to the strong K-Al2O3 and Fe-Al2O3 interactions. Furthermore, the H2 adsorption ability of the catalysts is enhanced with increasing Al2O3 content. The FTS performances of the catalysts were tested in a slurry-phase continuously stirred tank reactor （CSTR） under the reaction conditions of 260 ℃, 1.5 MPa, 1000 h^-1 and molar ratio of H2/CO 0.67 for 200 h. The results showed that the addition of small amounts of Al2O3 affects the activity of iron-based catalysts to a little extent. However, with further increase of Al2O3 content, the FTS activity and water gas shift reaction （WGS） activity are decreased severely. The addition of appropriate Al2O3 do not affect the product selectivity, but the catalysts incorporated with large amounts of Al2O3 have higher selectivity for light hydrocarbons and lower selectivity for heavy hydrocarbons.

Effect of Alumina Particle Size on Ni/Al2O3 Catalysts for p-Nitrophenol Hydrogenation

The catalytic hydrogenation of p-nitrophenol to p-aminophenol was investigated over Ni/Al2O3 catalyst on alumina support with different particle size. It is found that support particle size has significant influences on physiochemical properties and catalytic activity of the resulting Ni/Al2O3 catalyst, but little influence on the selec-tivity. At a comparable amount of Ni loading, the catalytic activity of Ni/Al2O3 prepared with alumina support of smaller particle size is lower. The reduction behavior of the catalyst is a key factor in determining the catalytic activity of Ni/Al2O3 catalyst. The supported nickel catalyst 10.3Ni/Al2O3-3 improves the life span of the membrane by reducing fouling on the membrane surface compared to nano-sized nickel.

Preparation of Fe_2P/Al_2O_3 and FeP/Al_2O_3 catalysts for the hydrotreating reactions

A 60%Fe/Al_2O_3 catalyst was prepared by the co-precipitation method.It was reduced by H_2 to produce metallic Fe,which was then sulfided by CS_2 to Fe_(0.96) S and Fe_3S_4 or phosphided by triphenylphosphine(PPh3) in liquid phases to Fe2 P and Fe P.It was found that the iron sulfides(Fe0.96 S and Fe_3S_4) exhibited the low activity for the hydrodesulfurization(HDS) reactions.The HDS activity was also low on the Fe(metal)/Al_2O_3 and Fe_2 P/Al_2O_3 catalysts since they were converted into Fe0.96 S and Fe_3S_4 during the HDS reactions.In contrast,the FeP/Al_2O_3 was found to be stable and active for the HDS reactions.In particular,Fe P/Al_2O_3 possessed significantly smaller Fe P particles than Fe P/C,leading to the significant higher HDS activity of FeP/Al_2O_3 than Fe P/C.

DBD coupled with MnOx/γ-Al2O3 catalysts for the degradation of chlorobenzene

This paper investigates the degradation of chlorobenzene by dielectric barrier discharge(DBD)coupled with MnOx/γ-Al2O3 catalysts.MnOx/γ-Al2O3 catalysts were prepared using the impregnation method and were characterized in detail by N2 adsorption/desorption,x-ray diffraction and x-ray photoelectron spectroscopy.Compared with the single DBD reactor,the coupled reactor has a better performance on the removal rate of chlorobenzene,the selectivity of COx,and the inhibition of ozone production,especially at low discharge voltages.The degradation rate of chlorobenzene and selectivity of COx can reach 96.3%and 53.0%,respectively,at the specific energy density of 1350 J l-1.Moreover,the ozone concentration produced by the discharge is significantly reduced because the MnOx/Al2O3 catalysts contribute to the decomposition of ozone to form oxygen atoms for the oxidation of chlorobenzene.In addition,based on analysis of the byproducts,the decomposition mechanism of chlorobenzene in the coupled reactor is also discussed.

Effects of Cerium Oxide on Ni/Al_2O_3 Catalysts for Decomposition of CH_4 and C_2H_4

Characteristics of carbon deposition of CH 4 and C 2H 4 decomposition over supported Ni and Ni Ce catalysts were studied by using a pulse reaction as well as BET, TPR, XPS and hydrogen chemisorption techniques. It is found that there is a metal semiconductor interaction (MScI) in the Ni Ce catalyst, and the effect of MScI on the carbon deposition of CH 4 decomposition is opposite to that of C 2H 4. A novel model of carbon deposition of CH 4 or C 2H 4 decomposition was proposed.

Characterization and performance of Cu/ZnO/Al_2O_3 catalysts prepared via decomposition of M(Cu,Zn)-ammonia complexes under sub-atmospheric pressure for methanol synthesis from H_2 and CO_2

Methanol synthesis from hydrogenation of CO2 is investigated over Cu/ZnO/Al2O3 catalysts prepared by decomposition of M（Cu,Zn）-ammonia complexes （DMAC） at various temperatures.The catalysts were characterized in detail,including X-ray diffraction,N2 adsorption-desorption,N2O chemisorption,temperature-programmed reduction and evolved gas analyses.The influences of DMAC temperature,reaction temperature and specific Cu surface area on catalytic performance are investigated.It is considered that the aurichalcite phase in the precursor plays a key role in improving the physiochemical properties and activities of the final catalysts.The catalyst from rich-aurichalcite precursor exhibits large specific Cu surface area and high space time yield of methanol （212 g/（Lcat·h）;T=513 K,p=3MPa,SV=12000 h-1）.

Selective Hydrogenation of Butyne-1,4-diol to Butane-1,4-diol over Ni/Al_2O_3-SiO_2 Catalysts

Ni/Al_2O_3-SiO_2 catalysts were synthesized via one-step method employing SiO_2 as an additive for the selective hydrogenation of butyne-1,4-diol(B_3D) to butane-1,4-diol(B1D). The prepared catalysts were evaluated by a series of characterization techniques including BET, XRD, SEM, EDX-mapping, TEM, H_2-TPR, XPS, NH_3-TPD and Py-FTIR. Compared to Ni/Al_2O_3 catalyst, the SiO_2-doped samples exhibited better B_3D conversion. SiO_2 could help to form a strong interaction between NiO with the support, which inhibited Ni agglomeration at high temperature, improved the Ni dispersion, and enhanced the hydrogenation activity. B_1D selectivity was mainly influenced by the quantity of Lewis acid sites in addition to the Ni dispersion. The catalyst with a silica loading of 6.4% demonstrated an excellent selectivity of 75.18%(by 13% higher than the contrastive Ni/Al_2O_3 catalyst), which was attributed to the larger amount of Lewis acid sites and the moderate interaction between NiO with the support, which could facilitate the nickel dispersion on a preferable surface area of 176.3 m^2/g of support.

CO_2 methanation over TiO_2–Al_2O_3 binary oxides supported Ru catalysts

TiO_2 modified Al_2O_3 binary oxide was prepared by a wet-impregnation method and used as the support for ruthenium catalyst. The catalytic performance of Ru/TiO_2–Al_2O_3catalyst in CO_2 methanation reaction was investigated. Compared with Ru/Al_2O_3 catalyst, the Ru/TiO_2–Al_2O_3catalytic system exhibited a much higher activity in CO_2 methanation reaction. The reaction rate over Ru/TiO_2–Al_2O_3 was 0.59 mol CO_2·(g Ru)1·h-1, 3.1 times higher than that on Ru/Al_2O_3[0.19 mol CO_2·(gRu)-1·h-1]. The effect of TiO_2 content and TiO_2–Al_2O_3calcination temperature on catalytic performance was addressed. The corresponding structures of each catalyst were characterized by means of H_2-TPR, XRD, and TEM. Results indicated that the averaged particle size of the Ru on TiO_2–Al_2O_3support is 2.8 nm, smaller than that on Al_2O_3 support of 4.3 nm. Therefore, we conclude that the improved activity over Ru/TiO_2–Al_2O_3catalyst is originated from the smaller particle size of ruthenium resulting from a strong interaction between Ru and the rutile-TiO_2 support, which hindered the aggregation of Ru nanoparticles.

Probing into Surface Sites of Fresh Mo_2N/Al_2O_3,Mo_2C/Al_2O_3 and MoP/Al_2O_3 Catalysts by CO Adsorption and In Situ FT-IR Spectroscopy

The surface nature of fresh Mo2N/Al2O3, Mo2C/Al2O3 and/MoP/Al2O3 catalysts, which were synthesized directly in the IR cell to avoid passivation, were characterized by in situ IR spectroscopy with CO as a probe molecule. CO adsorbed on fresh catalysts showed characteristic IR bands at 2045 cm-1 for Mo2N/Al2O3 catalyst, 2054 cm-1 for MozC/Al2O3 catalyst and 2037 cm-1 for MoP/Al2O3 catalyst, respectively. A strong band at 2200 cm-1 for Mo2N/Al2O3 catalyst, which could be ascribed to NCO species formed when CO reacted upon surface active nitrogen atoms, and a weak band at 2196 cm-1 for Mo2C/Al2O3 catalyst, which could be attributed to CCO species, were also detected. CO adsorbed on fresh Mo2N/Al2O3 catalyst, Mo2C/Al2O3 catalyst and MoP/Al2O3 catalyst, showed strong molecular adsorption, just like noble metals. Our experimental results are bolstered by direct IR evidence demonstrating the similarity in surface electronic property between the fresh Mo2N/Al2O3, Mo2C/Al2O3 and MoP/Al2O3 catalysts and noble metals.

NITRIC OXIDE DECOMPOSITION ON ALKALI-PROMOTED Pd/AL_2o_3 CATALYSTS

Alkali-promoted Pd/Al2O3 catalysts exhibit much higher activities in NO decomposition than Pd/Al2O3. FTIR study shows that on the alkali promoted catalyst.nitric oxide exists on the surface mainly in negatively charged form(NO-)at high temperatures.which is consistent with the activity improvement.

Oxidative desulfurization of dibenzothiophene over Fe promoted Co–Mo/Al_2O_3 and Ni–Mo/Al_2O_3 catalysts using hydrogen peroxide and formic acid as oxidants

This work reports the enhancing effect of a highly cost effective and efficient metal, Fe, incorporation to Co or Ni based Mo/Al2O3 catalysts in the oxidative desulfurization （ODS） of dibenzothiophene （DBT） using H2O2 and formic acid as oxidants. The influence of operating parameters i.e. reaction time, catalyst dose, reaction temperature and oxidant amount on oxidation process was investigated. Results revealed that 99% DBT conversion was achieved at 60℃ and 150 min reaction time over Fe-Ni-Mo/Al2O3. Fe tremendously enhanced the ODS activity of Co or Ni based Mo/Al2O3 catalysts following the activity order：Fe-Ni-Mo/Al2O3 〉 Fe-Co-Mo/Al2O3 〉 Ni-Mo/Al2O3 〉 Co-Mo/Al2O3, while H2O2 exhibited higher oxidation activity than formic acid over all catalyst systems. Insight about the surface morphology and textural properties of fresh and spent catalysts were achieved using scanning electron microscopy （SEM）, X-ray diffraction （XRD）, energy dispersive X-ray （EDX） analysis, Atomic Absorption Spectroscopy （AAS） and BET surface area analysis, which helped in the interpretation of experimental data. The present study can be deemed as an effective approach on industrial level for ODS of fuel oils crediting to its high efficiency, low process/catalyst cost, safety and mild operating condition.

Relationship between Cr-Al Interaction and the Performance of Cr-Al₂O₃Catalysts for Isobutane Dehydrogenation

A series of catalysts were prepared using the kneading molding method and the impregnation method as well as the dry mix method by using different raw materials. By using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and temperature-programmed reduction (TPR) techniques, we studied the relationship between the catalyst performance and the Cr-Al interaction in the catalytic dehydrogenation of isobutane. The results demonstrated that the Cr-Al interaction in the catalyst had a direct influence on the catalytic activity and the selectivity of isobutene. The catalysts prepared using the kneading molding method had higher catalytic activity and isobutene selectivity than those prepared using the dry mix method. By comparison, XRD, XPS, and TPR results showed that the greater the Cr-Al interaction in the catalyst was, the higher the catalytic activity was. Here, we propose a mechanism of isobutane dehydrogenation.

CHARACTERIZATION OF COBALT SITES IN REDUCED Co-Mo/Al_2O_3 AND Ru-Co-Mo/Al_2O_3 CATALYSTS

The two Co sites are well characterized in reduced Co-Mo/Al_2O_3 and Ru-Co- Mo/Al_2O_3 by new bands at 1895 and 1880 cm^(-1)in the IR spectra due to NO adsorption.