To investigate the seismic behavior of I-section columns made of 460 MPa high strength steel (HSS), six specimens were tested under constant axial load and cyclic horizontal load. The specimens were designed with di...To investigate the seismic behavior of I-section columns made of 460 MPa high strength steel (HSS), six specimens were tested under constant axial load and cyclic horizontal load. The specimens were designed with different width-to-thickness ratios and loaded under different axial load ratios. For each specimen, the failure mode was observed and hysteretic curve was measured. Comparison of different specimens on hysteretic characteristic, energy dissipation capacity and deformation capacity were further investigated. Test results showed that the degradation of bearing capacity was due to local buckling of flange and web. Under the same axial load ratio, as width-to-thickness ratio increased, the deformation area of local buckling became smaller. And also, displacement level at both peak load and failure load became smaller. In addition, the full extent of hysteretic curve, energy dissipation capacity, ultimate story drift angle decreased, and capacity degradation occurred more rapidly with the increase of width-to-thickness ratio or axial load ratio. Based on the capacity of story drift angle, limiting values which shall not be exceeded are suggested respectively for flange and web plate of 460 MPa HSS I-section columns when used in SMFs and in IMFs in the case of axial load ratio no more than 0.2. Such values should be smaller when the axial load ratio increases.展开更多
This study covers optimization of I-sectional flange beams. Scope of this study is limited to medium weight flange beams of Table 1 of IS 808:1983 but it can be further extended for the other sections of this code. Be...This study covers optimization of I-sectional flange beams. Scope of this study is limited to medium weight flange beams of Table 1 of IS 808:1983 but it can be further extended for the other sections of this code. Best possible geometric shape of the cross-section is found for maximum performance of the beam with minimum material consumption. All possible loading conditions are considered in the study for which a beam in flexure undergoes in its life. ANSYS software program is used for the analysis and optimizing the sections. It is found that sections MB 125, MB 300 and MB 400 of Table 1 of IS 808 are not the optimum sections but other alternative of these cross-sections is available which within the same material consumption performs better than these sections of IS code.展开更多
基金the National Natural Science Foundation of China under Grant No.51478244
文摘To investigate the seismic behavior of I-section columns made of 460 MPa high strength steel (HSS), six specimens were tested under constant axial load and cyclic horizontal load. The specimens were designed with different width-to-thickness ratios and loaded under different axial load ratios. For each specimen, the failure mode was observed and hysteretic curve was measured. Comparison of different specimens on hysteretic characteristic, energy dissipation capacity and deformation capacity were further investigated. Test results showed that the degradation of bearing capacity was due to local buckling of flange and web. Under the same axial load ratio, as width-to-thickness ratio increased, the deformation area of local buckling became smaller. And also, displacement level at both peak load and failure load became smaller. In addition, the full extent of hysteretic curve, energy dissipation capacity, ultimate story drift angle decreased, and capacity degradation occurred more rapidly with the increase of width-to-thickness ratio or axial load ratio. Based on the capacity of story drift angle, limiting values which shall not be exceeded are suggested respectively for flange and web plate of 460 MPa HSS I-section columns when used in SMFs and in IMFs in the case of axial load ratio no more than 0.2. Such values should be smaller when the axial load ratio increases.
文摘This study covers optimization of I-sectional flange beams. Scope of this study is limited to medium weight flange beams of Table 1 of IS 808:1983 but it can be further extended for the other sections of this code. Best possible geometric shape of the cross-section is found for maximum performance of the beam with minimum material consumption. All possible loading conditions are considered in the study for which a beam in flexure undergoes in its life. ANSYS software program is used for the analysis and optimizing the sections. It is found that sections MB 125, MB 300 and MB 400 of Table 1 of IS 808 are not the optimum sections but other alternative of these cross-sections is available which within the same material consumption performs better than these sections of IS code.