Preparation and Thermal Stability of AlMoON Based Solar Selective Absorption Coating

AlMoON based solar selective absorption coatings were deposited on stainless steel substrate by magnetron sputtering.The coatings included infrared reflection layer Mo,absorption layer AlMoN,absorption layer AlMoON and antireflection layer AlMoO from bottom to top.The surface of the deposited coatings is flat without obvious defects.The absorptivity and emissivity are 0.896 and 0.09,respectively,and the quality factor is 9.96.After heat treatment at 500℃-36 h,the surface roughness of the coating increases,a small number of cracks and other defects appear,and the broken part is still attached to the coating surface.A certain degree of element diffusion occurs in the coatings,resulting in the decline of the optical properties of the coatings.The absorptivity and emissivity are 0.883 and 0.131,respectively,the quality factor is 7.06,and the PC value is 0.0335.The coatings do not fail under this condition and have certain thermal stability.

Significantly enhanced thermal stability of HMX by phase-transition lysozyme coating

A new robust bio-inspired route by using lysozyme aqueous solution for surface modification on 1,3,5,7-tetranitro-1,3,5,7-tetrazocane(HMX)was described in this paper.HMX crystals were coated by in situ phase transition of lysozyme(PTL)molecules.The HMX decorated by PTL was characterized by SEM,XRD,FTIR and XPS,demonstrating a dense core-shell coating layer.The coverage of lysozyme on HMX crystal was calculated by the ratio of sulfur content.The surface coverage increased from 60.5% to 93.5% when the content of PTL was changed from 0.5 wt% to 2.0 wt%,indicating efficient coating.The thermal stability of HMX was investigated by in situ XRD and DSC.The thermal phase transition temperature of HMX(β to δ phase)was delayed by 42℃ with 2.0 wt% PTL coating,which prevented HMX from thermal damage and sensitivity by the effect of PTL coating.After heating at 215℃,large cracks appeared in the naked HMX crystal,while the PTL coated HMX still maintained intact,with the impact energy of HMX dropped dramatically from 5 J to 2 J.However,the impact energy of HMX with 1.0 wt% and 2.0 wt% coating content(HMX@PTL-1.0 and HMX@PTL-2.0)was unchanged(5 J).Present results potentially enable large-scale fabrication of polymorphic energetic materials with outstanding thermal stability by novel lysozyme coating.

Vertically aligned montmorillonite aerogel-encapsulated polyethylene glycol with directional heat transfer paths for efficient solar thermal energy harvesting and storage

The conversion and storage of photothermal energy using phase change materials(PCMs)represent an optimal approach for harnessing clean and sustainable solar energy.Herein,we encapsulated polyethylene glycol(PEG)in montmorillonite aerogels(3D-Mt)through vacuum impregnation to prepare 3D-Mt/PEG composite PCMs.When used as a support matrix,3D-Mt can effectively prevent PEG leakage and act as a flame-retardant barrier to reduce the flammability of PEG.Simultaneously,3D-Mt/PEG demonstrates outstanding shape retention,increased thermal energy storage density,and commendable thermal and chemical stability.The phase transition enthalpy of 3D-Mt/PEG can reach 167.53 J/g and remains stable even after 50 heating-cooling cycles.Furthermore,the vertical sheet-like structure of 3D-Mt establishes directional heat transport channels,facilitating efficient phonon transfer.This configuration results in highly anisotropic thermal conductivities that ensure swift thermal responses and efficient heat conduction.This study addresses the shortcomings of PCMs,including the issues of leakage and inadequate flame retardancy.It achieves the development and design of 3D-Mt/PEG with ultrahigh strength,superior flame retardancy,and directional heat transfer.Therefore,this work offers a design strategy for the preparation of high-performance composite PCMs.The 3D-Mt/PEG with vertically aligned and well-ordered array structure developed in this research shows great potential for thermal management and photothermal conversion applications.

Construction of core@double-shell structured energetic composites with simultaneously enhanced thermal stability and safety performance

The poor thermal stability and high sensitivity severely hinder the practical application of hexanitrohexaazaisowurtzitane(CL-20).Herein,a kind of novel core@double-shell CL-20 based energetic composites were fabricated to address the above issues.The coordination complexes which consist of natural polyphenol tannic acid(TA) and Fe~Ⅲ were chosen to construct the inner shell,while the graphene sheets were used to build the outer shell.The resulting CL-20/TA-Fe~Ⅲ/graphene composites exhibited simultaneously improved thermal stability and safety performance with only 1 wt% double-shell content,which should be ascribed to the intense physical encapsulation effect from inner shell combined with the desensitization effect of carbon nano-materials from outer shell.The phase transition(ε to γ) temperature increased from 173.70 ℃ of pure CL-20 to 191.87℃ of CL-20/TA-Fe~Ⅲ/graphene composites.Meanwhile,the characteristic drop height(H_(50)) dramatically increased from 14.7 cm of pure CL-20 to112.8 cm of CL-20/TA-Fe~Ⅲ/graphene composites,indicating much superior safety performance after the construction of the double-shell structure.In general,this work has provided an effective and versatile strategy to conquer the thermal stability and safety issues of CL-20 and contributes to the future application of high energy density energetic materials.

Research progress on classification,source,application of phytosterol esters,and their thermal oxidation stability

Phytosterol esters can effectively decrease serum cholesterol concentration in the human body and prevent cardio-cerebrovascular diseases.It was found that phytosterol esters exhibited better solubility and bioavailability than free phytosterols.In recent years,phytosterol esters have attracted increasing attention.However,during food processing,phytosterol esters are susceptible to degradation at high temperatures,resulting in certain losses and formation of potentially harmful substances for humans.This paper reviews the relevant literatures and updates on the thermal oxidation stability of phytosterol esters in recent years from the following aspects:(i)Sources,physiological activities,and applications of phytosterol esters;(ii)Oxidation mechanism of phytosterol esters;(iii)Effects of phytosterols species,the volume of addition,food matrix,heating temperature and time,and antioxidants on the thermal loss and oxidation stability of phytosterol esters.The research progress on the safety of phytosterol esters is also discussed in detail.Additionally,the prospects for future research are highlighted.

Further Analysis of Machine Tool Dimensional Accuracy and Thermal Stability under Varying Floor Temperature

Machining is as old as humanity, and changes in temperature in both the machine’s internal and external environments can be of great concern as they affect the machine’s thermal stability and, thus, the machine’s dimensional accuracy. This paper is a continuation of our earlier work, which aimed to analyze the effect of the internal temperature of a machine tool as the machine is put into operation and vary the external temperature, the machine floor temperature. Some experiments are carried out under controlled conditions to study how machine tool components get heated up and how this heating up affects the machine’s accuracy due to thermally induced deviations. Additionally, another angle is added by varying the machine floor temperature. The parameters mentioned above are explored in line with the overall thermal stability of the machine tool and its dimensional accuracy. A Robodrill CNC machine tool is used. The CNC was first soaked with thermal energy by gradually raising the machine floor temperature to a certain level before putting the machine in operation. The machine was monitored, and analytical methods were deplored to evaluate thermal stability. Secondly, the machine was run idle for some time under raised floor temperature before it was put into operation. Data was also collected and analyzed. It is observed that machine thermal stability can be achieved in several ways depending on how the above parameters are joggled. This paper, in conclusion, reinforces the idea of machine tool warm-up process in conjunction with a carefully analyzed and established machine floor temperature variation for the approximation of the machine tool’s thermally stability to map the long-time behavior of the machine tool.

Synthesis of Quaternary Phosphonium Salts with Ester Functional Group and Its Application to Improve the Thermal Stability of Modified Montmorillonite

Both of quaternary ammonium and quaternary phosphonium salts of bis-hydroxyethyl terephthalate （BHET） were successfully synthesized and characterized by fourier transform infrared spectroscopy （FT-IR）. These two kinds of salts were used to intercalate Na-MMT to yield two kinds of respective organo-modified MMTs. Basal spacing and thermal stability were investigated by using X-ray diffraction （XRD） and thermogravimetric analysis （TGA）, respectively. The experimental results show that, as compared with Na-MMT, basal spacings of both of MMTs modified by the quaternary phosphonium salt of BHET （BHETPP） and the quaternary ammonium salt of BHET （BHEA）, increase from 12.4 A to 19.7/k and 31.3 A, respec-tively. Thermal stability of BHETPP-modified MMT is much better than that of BHEA-modified MMT, i e, T otof BHETPP-modified MMT is around 400℃ while Tcmset of BHEA-modified MMT is near 250℃. Therefore, with en-larged basal spacing and excellent thermal stability, BHETPP-modified MMT is a promising organo-modified MMT which may be used to prepare polyethylene terephthalate/MMT nanocomposite with high thermal and mechanical performance.

Thermal stability and long-acting antibacterial activity of phosphonium montmorillonites

Na-montruorillonite （Na-MMT） was exchanged with three quaternary atkylphosphonium salts： decyl tributylphosphonium bromide （DTBPBr）, dodecyl tributylphosphonium bromide （DDTBPBr） and hexadecyl tributylphosphonium bromide （HDTBPBr）, to investigate the effects of phosphonium salts species and relative molecular mass on the characteristics, morphology, thermal stability and long-acting antibacterial property of phosphonium montmorillonites. The resulting modified montmorillonites were characterized by the FTIR, XRD, TEM, and TG/DTG techniques. And minimum inhibitory concentration （MIC） was used to investigate antibacterial activity. The results show that the phosphonium salts are intercalated into Na-MMT, and the basal spacing of P-MMTs is enlarged with the increase of phosphonium salt content or the growth of alkyl chain length. DDTBP-MMT-3 with 19.83% （mass fraction of dodecyl tributylphosphonium salts, displays excellent thermal stability and long-acting antibacterial activity.

Effects of Layer Change and Chemical Composition on Thermal Stability and Catalytic Activity of Pillared Montmorillonite

ＥｆｅｃｔｓｏｆＬａｙｅｒＣｈａｎｇｅａｎｄＣｈｅｍｉｃａｌＣｏｍｐｏｓｉｔｉｏｎｏｎＴｈｅｒｍａｌＳｔａｂｉｌｉｔｙａｎｄＣａｔａｌｙｔｉｃＡｃｔｉｖｉｔｙｏｆＰｉｌａｒｅｄＭｏｎｔｍｏｒｉｌｏｎｉｔｅＬｉａｏＨｕｉｓｈｅｎｇ，ＨｅＭｉｎｇｙｕａｎ...

Polymer Fiber Rigid Network with High Glass Transition Temperature Reinforces Stability of Organic Photovoltaics

Organic photovoltaics(OPVs)need to overcome limitations such as insufficient thermal stability to be commercialized.The reported approaches to improve stability either rely on the development of new materials or on tailoring the donor/acceptor morphology,however,exhibiting limited applicability.Therefore,it is timely to develop an easy method to enhance thermal stability without having to develop new donor/acceptor materials or donor–acceptor compatibilizers,or by introducing another third component.Herein,a unique approach is presented,based on constructing a polymer fiber rigid network with a high glass transition temperature(T_(g))to impede the movement of acceptor and donor molecules,to immobilize the active layer morphology,and thereby to improve thermal stability.A high-T_(g) one-dimensional aramid nanofiber(ANF)is utilized for network construction.Inverted OPVs with ANF network yield superior thermal stability compared to the ANF-free counterpart.The ANF network-incorporated active layer demonstrates significantly more stable morphology than the ANF-free counterpart,thereby leaving fundamental processes such as charge separation,transport,and collection,determining the device efficiency,largely unaltered.This strategy is also successfully applied to other photovoltaic systems.The strategy of incorporating a polymer fiber rigid network with high T_(g) offers a distinct perspective addressing the challenge of thermal instability with simplicity and universality.

Intrinsic thermal stability of inverted perovskite solar cells based on electrochemical deposited PEDOT

Thermal stability of perovskite materials is an issue impairing the long-term operation of inverted perovskite solar cells(PSCs). Herein, the thermal attenuation mechanism of the MAPb I3films that deposited on two different hole transport layers(HTL), poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate)(PEDOT:PSS) and poly(3,4-ethylenedioxythiophene)(PEDOT), is comprehensively studied by applying a heat treatment at 85℃. The thermal stress causes the mutual ions migration of I, Pb and Ag through the device, which leads to the thermal decomposition of perovskite to form Pb I2. Interestingly, we find that I ions tend to migrate more towards electron transport layer(ETL) during heating, which is different with the observation of I ions migration towards HTL when bias pressure is applied. Moreover, the use of electrochemical deposited PEDOT as HTL significantly decreases the defect density of MAPb I3films as compared to PEDOT:PSS supported one. The electrochemical deposition PEDOT has good carrier mobility and low acidity, which avoids the drawbacks of aqueous PEDOT:PSS. Accordingly, the inverted PSCs based on PEDOT show superior durability than that with PEDOT:PSS. Our results reveal detailed degradation routes of a new kind of inverted PSCs which can contribute to the understanding of the failure of thermal-aged inverted PSCs.

Thermal–moisture dynamics and thermal stability of active layer in response to wet/dry conditions in the central region of the Qinghai–Tibet Plateau,China

The amount of rainfall varies unevenly in different regions of the Qinghai-Tibet Plateau, with some regions becoming wetter and others drier. Precipitation has an important impact on the process of surface energy balance and the energy-water transfer within soils. To clarify the thermal-moisture dynamics and thermal stability of the active layer in permafrost regions under wet/dry conditions, the verified water-vapour-heat coupling model was used. Changes in the surface energy balance, energy-water transfer within the soil, and thickness of the active layer were quantitatively analyzed. The results demonstrate that rainfall changes significantly affect the Bowen ratio, which in turn affects surface energy exchange. Under wet/dry conditions, there is a positive correlation between rainfall and liquid water flux under the hydraulic gradient;water vapour migration is the main form under the temperature gradient, which indicates that the influence of water vapour migration on thermalmoisture dynamics of the active layer cannot be neglected. Concurrently, regardless of wet or dry conditions,disturbance of the heat transport by conduction caused by rainfall is stronger than that of convection by liquid water. In addition, when rainfall decreases by 1.5 times(212 mm) and increases by 1.5 times(477 mm), the thickness of the active layer increases by 0.12 m and decreases by 0.21 m, respectively. The results show that dry conditions are not conducive to the preservation of frozen soil;however, wet conditions are conducive to the preservation of frozen soil, although there is a threshold value. When this threshold value is exceeded, rainfall is unfavourable for the development of frozen soil.

Optimizing the morphology of all-polymer solar cells for enhanced photovoltaic performance and thermal stability

Due to the complicated film formation kinetics, morphology control remains a major challenge for the development of efficient and stable all-polymer solar cells(all-PSCs). To overcome this obstacle, the sequential deposition method is used to fabricate the photoactive layers of all-PSCs comprising a polymer donor PTzBI-oF and a polymer acceptor PS1. The film morphology can be manipulated by incorporating amounts of a dibenzyl ether additive into the PS1 layer. Detailed morphology investigations by grazing incidence wide-angle X-ray scattering and a transmission electron microscope reveal that the combination merits of sequential deposition and DBE additive can render favorable crystalline properties as well as phase separation for PTzBI-oF:PS1 blends. Consequently, the optimized all-PSCs delivered an enhanced power conversion efficiency(PCE) of 15.21%along with improved carrier extraction and suppressed charge recombination. More importantly, the optimized all-PSCs remain over 90% of their initial PCEs under continuous thermal stress at 65 °C for over 500 h. This work validates that control over microstructure morphology via a sequential deposition process is a promising strategy for fabricating highly efficient and stable all-PSCs.

Stability and Thermal Property Optimization of Propylene Glycol-Based MWCNT Nanofluids

Propylene glycol-based MWCNT(multi-walled carbon nanotubes)nanofluids were prepared in the framework of a two-step method and by using a suitable PVP(polyvinyl pyrrolidone)dispersant.The BBD(Box-Behnken design)model was exploited to analyze 17 sets of experiments and examine the sensitivity of the absorbance to three parameters,namely the concentration of MWCNT,the SN ratio(mass ratio of carbon nanotubes to sur-factants)and the sonication time.The results have revealed that,while the SN ratio and concentration of MWCNT have a strong effect on the absorbance,the influence of the sonication time is less important.The sta-tistical method of analysis of variance(ANOVA)was further used to determine the F-and p-values of the model.Five experiments were run to validate this approach.Since sample 2 was found to display the greatest absorbance,it was selected for stability monitoring as well as thermal conductivity and viscosity measurements.This sample has been found to be stable;the viscosity decreased with increasing temperature;the addition of MWCNT nano-particles was more effective in improving the thermal conductivity of propylene glycol than other methods in the literature.Moreover,the MWCNT nanofluid based on propylene glycol exhibited higher thermal conductivity at low temperatures.

17.13% Efficiency and Superior Thermal Stability of Organic Solar Cells Based on a Comb-Shape Active Blend

With rapid progress,organic solar cells(OSCs)are getting closer to the target of real application.However,the stability issue is still one of the biggest challenges that have to be resolved.Especially,the thermal stability of OSCs is far from meeting the requirements of the application.Here,based on the layer-by-layer(LBL)process and by utilizing the dissolubility nature of solvent and materials,binary inverted OSCs(ITO/AZO/PM6/BTP-eC9/MoO3/Ag)with comb shape active morphology are fabricated.High efficiency of 17.13%and simultaneous superior thermal stability(with 93%of initial efficiency retained in~9:00 h under 85℃in N_(2))are demonstrated,showing superior stability to reference cells.The enhancements are attributed to the formed optimal comb shape of the active layer,which could provide a larger D/A interface,thus more charge carriers,render the active blend a more stable morphology,and protect the electrode by impeding ion's migration and corrosion.To the best of our knowledge,this is the best thermal stability of binary OSCs reported in the literature,especially when considering the high efficiency of over 17%.

Thermal stability analysis of a satellite-borne optical bench based on quasi-kinematic support

Macao Science Satellite-1(known as MSS-1)is a low-inclination mission that will be launched at the beginning of 2023.An optical bench is used for accessing high-precision strength and direction measurements of the magnetic field.In this paper,we present a thermal stability design for the optical bench based on quasi-kinematic support by kinematic hinges on the MSS-1.The change in angles with the finite element method(FEM)model modified by thermal deformation test data is analyzed.The robustness of the structure is also investigated via the Monte Carlo method.Two main results are obtained.First,the peak-to-peak value(Vp-p)of the inter-boresight angle is at most 1.24″,and the Vp-p of the inter-boresight angle modification and analysis is no more than 3.13″,both of which are better than those on the Swarm satellites in orbit.Second,the 90°fibers of the carbon-reinforced arm need to be strictly controlled during the technological process.

Exceptional thermal stability and enhanced hardness in a nanostructured Mg-Gd-Y-Zn-Zr alloy processed by high pressure torsion

A Mg-8.2Gd-3.8Y-1.0Zn-0.4Zr(wt.%) alloy is processed by solution treatment and high pressure torsion(HPT) at room temperature to produce a nanostructured light material with high hardness. The stability of this alloy is subsequently tested through isochronal annealing for 0.5 h at 373 K to 673 K. The results reveal a thermal stability that is vastly superior to that of conventional Mg-based alloys processed by severe plastic deformation: the grain size remains at around 50 nm on heating to 573 K, and as the temperature is increased to 673 K,grain growth is restricted to within 500 nm. The stability of grain refinement of the present alloy/processing combination allowing grain size to be limited to 55 nm after exposure at 573 K, appears to be nearly one order of magnitude better than for the other SPD processed Mg-RE type alloys, and 2 orders of magnitude better than those of SPD processed RE-free Mg alloys. This superior thermal stability is attributed to formation of co-clusters near and segregation at grain boundaries, which cause a thermodynamic stabilization of grain size, as well as formation of β-Mg_(5)RE equilibrium phase at grain boundaries, which impede grain growth by the Zener pinning effect. The hardness of the nanostructured Mg-Gd-Y-Zn-Zr alloy increases with increasing annealing temperature up to 573 K, which is quite different from the other SPD-processed Mg-based alloys. The high hardness of 136 HV after annealing at 573 K is mainly due to solute segregation and solute clustering at or near grain boundaries.

Microstructure and interface thermal stability of C/Mo double-coated SiC fiber reinforced γ-TiAl matrix composites

C/Mo duplex coating interfacially modified SiC fiber-reinforced γ-TiAl matrix composite （SiCf/C/Mo/γ-TiA1） was prepared by foil-fiber-foil method to investigate its interfacial modification effect. SiCf/C/TiAl composites were also prepared under the same processing condition for comparision. Both kinds of the composites were thermally exposed in vacuum at 800 and 900℃ for different durations in order to study thermal stability of the interfacial zone. With the aids of scanning electron microscope （SEM） and energy dispersive spectrometer （EDS）, the interracial microstructures of the composites were investigated. The results reveal that, although adding the Mo coating, the interfacial reaction product of the SiCf/C/Mo/TiAl composite is the same with that of the SiCf/C/TiA1 composite, which is TiC/Ti2AlC between the coating and the matrix. However, C/Mo duplex coating is more efficient in hindering interfacial reaction than C single coating at 900 ℃ and below. In addition, a new layer of interfacial reaction product was found between Ti2AlC and the matrix after 900 ℃, 200 h thermal exposure, which is rich in V and close to the chemical composition of B2 phase.

Thermal stability,crystallization behavior,Vickers hardness and magnetic properties of Fe-Co-Ni-Cr-Mo-C-B-Y bulk metallic glasses

Thermal stability,crystallization behavior,Vickers hardness and magnetic properties of the Fe41Co7-xNixCr15Mo14C15B6Y2（x=0,1,3,5） bulk metallic glasses were investigated.The Fe41Co7-xNixCr15Mo14C15B6Y2（x=0,1,3,5） metallic glasses were fabricated by copper mold casting method.The thermal stability and crystallization behavior of the metallic glass rods were investigated by differential scanning calorimetry and isothermal experiments.Hardness measurements for samples annealed at different temperatures for different time were carried out at room temperature by the Vickers hardness tester,and magnetic measurements were performed at different temperatures by the vibrating sample magnetometer.It is shown that the addition of Ni does not play a positive role for enlarging ΔTx and GFA from parameter γ（=Tx/（Tg＋Tl））,and it can,however,increase the activation energy in the initial stage of crystallization by changing the initial crystallization behavior.The minor addition of Ni can refine the crystal grain obtained from the full crystallization experiment.The primary crystallization causes the decrease of hardness in these alloys,and as the crystallization continues,the hardness in all samples increases instead due to the precipitation of carbide and boride.The annealing temperature has an obvious effect on magnetic properties of these alloys,and the minor addition of Ni can effectively prevent the alloy annealed at high temperature to transform from paramagnetic to ferromagnetic state.

Thermal stability of electrodeposited nanocrystalline nickel assisted by flexible friction

Nanocrystalline nickel coating was prepared by flexible friction assisted electrodeposition technology in an additive-free Watts bath.The coating consists of massive equiaxial crystals with an average grain size of about 24 nm and exhibits a（111） preferred orientation.The differential scanning calorimetry（DSC） analysis of nanocrystalline nickel demonstrates that the peak temperature of rapid grain growth is about 285.4 °C,and the peak temperature of grain growth towards equilibrium is around 431.5 °C.The isochronous annealing results reveal that abnormal grain growth behavior is not observed in nanocrystalline nickel without sulfur-containing.The thermal stability of the deposition was improved due to its initial microstructure of the as-deposited nickel and a certain amount of annealing nano-twins with low-energy,which reduces the driving force for grain growth.Consequently,the coating shows a low residual tensile stress of about 50 MPa and a high microhardness of HV 400 at the annealing temperature of 450 °C.