AlCrFeNiCu high-entropy alloy (THA) was synthesized by the arc melting and casting method. The alloy exhibits simple FCC and BCC solid solution phases rather than intermetallic compounds. The reason is that the Gibb...AlCrFeNiCu high-entropy alloy (THA) was synthesized by the arc melting and casting method. The alloy exhibits simple FCC and BCC solid solution phases rather than intermetallic compounds. The reason is that the Gibbs free energy of mixing of the equimolar A1CrFeNiCu alloy is smaller than that of inter-metallic compounds by calculation according to the Miedema model .展开更多
By introducing Cu, AlCoCrFeNiCux (x values in molar ratio, x = 0, 0.1, 0.5, 1.0, 1.5, 2.0, and 2.5) alloys were designed and prepared. The effects of Cu on microstructure and properties of Al Co Cr Fe Ni alloy were ...By introducing Cu, AlCoCrFeNiCux (x values in molar ratio, x = 0, 0.1, 0.5, 1.0, 1.5, 2.0, and 2.5) alloys were designed and prepared. The effects of Cu on microstructure and properties of Al Co Cr Fe Ni alloy were investigated. The introduction of Cu results in the formation of Cu-rich FCC solid solution phase when Cu content is low.There are two FCC solid solution phases, i.e., Cu-rich FCC solid solution phase and phase transformation-induced FCC solid solution phase, when the Cu content is more than 1.0. Both the yield stress and plastic strain of alloy show a turning point when the Cu content is 0.5. Among the seven alloys, Cu0.5 alloy exhibits the largest yield stress of 1187 MPa and the lowest plastic strain of 16.01 %.展开更多
The approximately equimolar ratio A1CrNiSiTi multi-principal element alloy (MPEA) coatings were fab- ricated by laser cladding on Ti-6Al-4V (Ti64) alloy. Scanning electron microscopy (SEM), equipped with an ener...The approximately equimolar ratio A1CrNiSiTi multi-principal element alloy (MPEA) coatings were fab- ricated by laser cladding on Ti-6Al-4V (Ti64) alloy. Scanning electron microscopy (SEM), equipped with an energy-dispersive spectroscopy (EDS), and X-ray diffrac- tion (XRD) were used to characterize the microstructure and composition. Investigations show that the coatings consist of (Ti, Cr)5Si3 and NiA1 phases, formed by in situ reaction. The phase composition is initially explicated according to obtainable binary and ternary phase diagrams, and the formation Gibbs energy of TisSi3, VsSi3 and CrsSi3. Dry sliding reciprocating friction and wear tests of the A1CrNiSiTi coating and Ti64 alloy substrate without coating were evaluated. A surface mapping profiler was used to evaluate the wear volume. The worn surface was characterized by SEM-EDS. The hardness and wear resistance of the A1CrNiSiTi coating are well compared with that of the basal material (Ti64). The main wear mechanism of the AICrNiSiTi coating is slightly adhesive transfer from GCrl5 counterpart, and a mixed layer com- posed of transferred materials and oxide is formed.展开更多
基金financial support for this research by Natural Science Foundation of Guangxi Province (0575-18)Guangxi Technology Research Project (0639003)Guangxi University Scientific Research Foundation (x071066)
文摘AlCrFeNiCu high-entropy alloy (THA) was synthesized by the arc melting and casting method. The alloy exhibits simple FCC and BCC solid solution phases rather than intermetallic compounds. The reason is that the Gibbs free energy of mixing of the equimolar A1CrFeNiCu alloy is smaller than that of inter-metallic compounds by calculation according to the Miedema model .
基金financially supported by the National Natural Science Foundation of China (No. 50825402)the National Basic Research Program of China (No. 2011CB610405)+2 种基金Guangxi Natural Science Foundation (No. 2013GXNSFBA019251)Guangxi University of Science and Technology Research Projects (No. 2013YB071)Guangxi University for Nationalities Research Projects (No. 2011QD021)
文摘By introducing Cu, AlCoCrFeNiCux (x values in molar ratio, x = 0, 0.1, 0.5, 1.0, 1.5, 2.0, and 2.5) alloys were designed and prepared. The effects of Cu on microstructure and properties of Al Co Cr Fe Ni alloy were investigated. The introduction of Cu results in the formation of Cu-rich FCC solid solution phase when Cu content is low.There are two FCC solid solution phases, i.e., Cu-rich FCC solid solution phase and phase transformation-induced FCC solid solution phase, when the Cu content is more than 1.0. Both the yield stress and plastic strain of alloy show a turning point when the Cu content is 0.5. Among the seven alloys, Cu0.5 alloy exhibits the largest yield stress of 1187 MPa and the lowest plastic strain of 16.01 %.
基金supported by the Chongqing Research Program of Basic Research and Frontier Technology(No.CSTC2013jcyjA50016)the National Natural Science Foundation of China(Nos.51401039,51571037 and 51204110)the Scientific and Technological Research Program of Chongqing Municipal Education Commission(No.KJ1709204).
文摘The approximately equimolar ratio A1CrNiSiTi multi-principal element alloy (MPEA) coatings were fab- ricated by laser cladding on Ti-6Al-4V (Ti64) alloy. Scanning electron microscopy (SEM), equipped with an energy-dispersive spectroscopy (EDS), and X-ray diffrac- tion (XRD) were used to characterize the microstructure and composition. Investigations show that the coatings consist of (Ti, Cr)5Si3 and NiA1 phases, formed by in situ reaction. The phase composition is initially explicated according to obtainable binary and ternary phase diagrams, and the formation Gibbs energy of TisSi3, VsSi3 and CrsSi3. Dry sliding reciprocating friction and wear tests of the A1CrNiSiTi coating and Ti64 alloy substrate without coating were evaluated. A surface mapping profiler was used to evaluate the wear volume. The worn surface was characterized by SEM-EDS. The hardness and wear resistance of the A1CrNiSiTi coating are well compared with that of the basal material (Ti64). The main wear mechanism of the AICrNiSiTi coating is slightly adhesive transfer from GCrl5 counterpart, and a mixed layer com- posed of transferred materials and oxide is formed.