This paper gives performance analysis of a three phase Permanent Magnet Synchronous Generator (PMSG) connected to a Vertical Axis Wind Turbine (VAWT). Low speed wind condition (less than 5 m/s) is taken in considerati...This paper gives performance analysis of a three phase Permanent Magnet Synchronous Generator (PMSG) connected to a Vertical Axis Wind Turbine (VAWT). Low speed wind condition (less than 5 m/s) is taken in consideration and the entire simulation is carried in Matlab/Simulink environment. The rated power for the generator is fixed at 1.5 KW and number of pole at 20. It is observed under low wind speed of6 m/s, a turbine having approximately1 mof radius and2.6 mof height develops 150 Nm mechanical torque that can generate power up to 1.5 KW. The generator is designed using modeling tool and is fabricated. The fabricated generator is tested in the laboratory with the simulation result for the error analysis. The range of error is about 5%-27% for the same output power value. The limitations and possible causes for error are presented and discussed.展开更多
This paper proposes highly charged ions pumped by intense laser to produce very high order harmonics. Numerical simulations and full quantum theory of Ne^9＋ ions driven by laser pulses at 1064 nm in the power range o...This paper proposes highly charged ions pumped by intense laser to produce very high order harmonics. Numerical simulations and full quantum theory of Ne^9＋ ions driven by laser pulses at 1064 nm in the power range of 109 W/cm^2 1015 W/cm^2 show that the emission spectrum corresponds to the electronic transitions from the excited states to the ground state, which is very different from the spectrum of general high-order harmonic generation. In such situation, harmonic order as high as 1000 can be obtained without producing lower order harmonics and the energy conversion efficiency is close to general high order harmonic generation of hydrogen atom in the same laser field.展开更多
During the past thirty years, two generations of low alloy steels(ferrite/pearlite followed by bainite/martensite) have been developed and widely used in structural applications. The third-generation of low alloy stee...During the past thirty years, two generations of low alloy steels(ferrite/pearlite followed by bainite/martensite) have been developed and widely used in structural applications. The third-generation of low alloy steels is expected to achieve high strength and improved ductility and toughness, while satisfying the new demands for weight reduction, greenness, and safety. This paper reviews recent progress in the development of third-generation low alloy steels with an M^3 microstructure, namely, microstructures with multi-phase, meta-stable austenite, and multi-scale precipitates. The review summarizes the alloy designs and processing routes of microstructure control, and the mechanical properties of the alloys.The stabilization of retained austenite in low alloy steels is especially emphasized. Multi-scale nano-precipitates, including carbides of microalloying elements and Cu-rich precipitates obtained in third-generation low alloy steels, are then introduced. The structure–property relationships of third-generation alloys are also discussed. Finally, the promises and challenges to future applications are explored.展开更多
In order to realize further stability of a stack-type thermoelectric power generating module (i.e. no electrical connections inside), flexible materials of metal springs and/or rods having restoring forces were instal...In order to realize further stability of a stack-type thermoelectric power generating module (i.e. no electrical connections inside), flexible materials of metal springs and/or rods having restoring forces were installed between lower-temperature-sides of thermoelectric elements. These flexible materials were expected to play three important roles of interpolating different thermal expansions of the module components, enlarging heat removal area and penetration of any media through themselves. Then, a low-boiling-point medium (i.e. NOVEC manufactured by 3M Japan Ltd.) was also applied for a high-speed direct heat removal via its phase change from the lower-temperature-sides of the thermoelectric elements in the proposing stack-type thermoelectric power generating module. No electrical disconnections inside the module were confirmed for more than 9 years of use, indicating further module stability. The power generating density was improved to about 120 mW·m-2 with SUS304 springs having 0.7 mm diameter. Increasing power generating density can be expected in terms of suitable selection of flexible metal with high Vickers hardness, cavities control on the spring surface, more vigorous multiphase flow with adding powders to the medium and optimization of the module configurations according to numerical simulations.展开更多
文摘This paper gives performance analysis of a three phase Permanent Magnet Synchronous Generator (PMSG) connected to a Vertical Axis Wind Turbine (VAWT). Low speed wind condition (less than 5 m/s) is taken in consideration and the entire simulation is carried in Matlab/Simulink environment. The rated power for the generator is fixed at 1.5 KW and number of pole at 20. It is observed under low wind speed of6 m/s, a turbine having approximately1 mof radius and2.6 mof height develops 150 Nm mechanical torque that can generate power up to 1.5 KW. The generator is designed using modeling tool and is fabricated. The fabricated generator is tested in the laboratory with the simulation result for the error analysis. The range of error is about 5%-27% for the same output power value. The limitations and possible causes for error are presented and discussed.
基金Project supported by the National Natural Science Foundation of China (Grant No. 10574030)
文摘This paper proposes highly charged ions pumped by intense laser to produce very high order harmonics. Numerical simulations and full quantum theory of Ne^9＋ ions driven by laser pulses at 1064 nm in the power range of 109 W/cm^2 1015 W/cm^2 show that the emission spectrum corresponds to the electronic transitions from the excited states to the ground state, which is very different from the spectrum of general high-order harmonic generation. In such situation, harmonic order as high as 1000 can be obtained without producing lower order harmonics and the energy conversion efficiency is close to general high order harmonic generation of hydrogen atom in the same laser field.
基金financially supported by the National Natural Science Foundation of China (No. 51701012)the National Basic Research Program of China (973 Program: No. 2010CB630801)the Fundamental Research Funds for the Central Universities (No. FRF-TP-17-004A1)
文摘During the past thirty years, two generations of low alloy steels(ferrite/pearlite followed by bainite/martensite) have been developed and widely used in structural applications. The third-generation of low alloy steels is expected to achieve high strength and improved ductility and toughness, while satisfying the new demands for weight reduction, greenness, and safety. This paper reviews recent progress in the development of third-generation low alloy steels with an M^3 microstructure, namely, microstructures with multi-phase, meta-stable austenite, and multi-scale precipitates. The review summarizes the alloy designs and processing routes of microstructure control, and the mechanical properties of the alloys.The stabilization of retained austenite in low alloy steels is especially emphasized. Multi-scale nano-precipitates, including carbides of microalloying elements and Cu-rich precipitates obtained in third-generation low alloy steels, are then introduced. The structure–property relationships of third-generation alloys are also discussed. Finally, the promises and challenges to future applications are explored.
文摘In order to realize further stability of a stack-type thermoelectric power generating module (i.e. no electrical connections inside), flexible materials of metal springs and/or rods having restoring forces were installed between lower-temperature-sides of thermoelectric elements. These flexible materials were expected to play three important roles of interpolating different thermal expansions of the module components, enlarging heat removal area and penetration of any media through themselves. Then, a low-boiling-point medium (i.e. NOVEC manufactured by 3M Japan Ltd.) was also applied for a high-speed direct heat removal via its phase change from the lower-temperature-sides of the thermoelectric elements in the proposing stack-type thermoelectric power generating module. No electrical disconnections inside the module were confirmed for more than 9 years of use, indicating further module stability. The power generating density was improved to about 120 mW·m-2 with SUS304 springs having 0.7 mm diameter. Increasing power generating density can be expected in terms of suitable selection of flexible metal with high Vickers hardness, cavities control on the spring surface, more vigorous multiphase flow with adding powders to the medium and optimization of the module configurations according to numerical simulations.
