A 1-bit electronically reconfigurable beam steerable metasurface reflectarray with multiple polarization manipulations

A 1-bit electronically controlled metasurface reflectarray is presented to achieve beam steering with multiple polarization manipulations. A metsurface unit cell loaded by two PIN diodes is designed. By switching the two PIN diodes between ON and OFF states, the isotropic and anisotropic reflections can be flexibly achieved. For either the isotropic reflection or the anisotropic reflection, the two operation states achieve the reflection coefficients with approximately equal magnitude and 180°out of phase, thus giving rise to the isotropic/anisotropic 1-bit metasurface unit cells. With the 1-bit unit cells, a 12-by-12 metasurface reflectarray is optimally designed and fabricated. Under either y-or x-polarized incident wave illumination, the reflectarray can achieve the co-polarized and cross-polarized beam scanning, respectively, with the peak gains of 20.08 d Bi and 17.26 d Bi within the scan range of about ±50°. With the right-handed circular polarization(RHCP) excitation, the left-handed circular polarization(LHCP) radiation with the peak gain of 16.98 d Bic can be achieved within the scan range of ±50°. Good agreement between the experimental results and the simulation results are observed for 2D beam steering and polarization manipulation capabilities.

A study of pulsed high voltage driven hollow-cathode electron beam sources through synchronous optical trigger

In this study,a pulsed,high voltage driven hollow-cathode electron beam sources through an optical trigger is designed with characteristics of simple structure,low cost,and easy triggering.To validate the new design,the characteristics of hollow-cathode discharge and electron beam characterization under pulsed high voltage drive are studied experimentally and discussed by discharge characteristics and analyses of waveform details,respectively.The validation experiments indicate that the pulsed high voltage supply significantly improves the frequency and stability of the discharge,which provides a new solution for the realization of a high-frequency,high-energy electron beam source.The peak current amplitude in the high-energy electron beam increases from 6.2 A to 79.6 A,which indicates the pulsed power mode significantly improves the electron beam performance.Besides,increasing the capacitance significantly affects the highcurrent,lower-energy electron beam more than the high-energy electron beam.

Effect of Cryogenic Treatment on Microstructure and Tribological Property Evolution of Electron Beam Melted Ti6Al4V

Cryogenic treatment was used to improve the tribological properties of Ti6Al4V artificial hip joint implants.Cryogenic treatment at-196℃with different holding time were carried out on Ti6Al4V specimens fabricated using electron beam melting(EBM),and their microstructure and tribological properties evolution were systematically analyzed by scanning electron microscopy(SEM),vickers hardness,and wear tests.The experimental results show that the as-fabricated specimen consists of lamellarαphase andβcolumnar crystal.While,the thickness of lamellarαphase decreased after cryogenic treatment.In addition,it can be found that the fineαphase was precipitated and dispersed between the lamellarαphase with the holding time increase.Vickers hardness shows a trend of first increasing and then decreasing.The wear rate of the specimen cryogenic treated for 24 h is the minimum and the average friction coefficient is 0.50,which is reduced by 14.61%compared with the as-fabricated.The wear mechanism of the as-fabricated specimen is severe exfoliation,adhesive,abrasive,and slight fatigue wear.However,the specimen cryogenic treated for 24 h shows slight adhesive and abrasive wear.It can be concluded that it is feasibility of utilizing cryogenic treatment to reduce the wear of EBMed Ti6Al4V.

Generation and Suppression of Pendant Droplet Oscillation in Electron Beam Directed Energy Deposition

Electron beam–directed energy deposition(EB–DED)has emerged as a promising wire-based metal additive manufacturing technique.However,the effects of EBs on pendant droplets at wire tips have not yet been determined.The aim of this study is to enhance the understanding of this action by analyzing the mechanism of droplet oscillation.The pendant droplet oscillation phenomenon hinders the stable transfer of droplets to the molten pool and limits the feasibility of manufacturing complex lattice structures by EB–DED.Hence,another aim of this study is to create an oscillation suppression method.An escalating asymmetric amplitude is the main characteristic of droplet oscillation.The primary oscillationinducing force is the recoil force generated from the EB-acted local surface of the droplet.The physical mechanism of this force is the rapid increase and uneven distribution of the local surface temperature caused by the partial action of the EB.The prerequisites for droplet oscillation include vacuum conditions,high power densities,and bypass wire feeding processes.The proposed EB–dynamic surrounding melting(DSM)method can be applied to conveniently and effectively suppress oscillations,enable the accurate transfer of droplets to the molten pool,and achieve stable processes for preparing the strut elements of lattice structures.Lowering the temperature and improving the uniformity of its distribution are the mechanisms of oscillation suppression in EB–DSM.In this study,the physical basis for interpreting the mechanism by which EBs act on droplets and the technical basis for using EB–DED to prepare complex lattice structure parts are provided.

Tailoring electron vortex beams with customizable intensity patterns by electron diffraction holography

An electron vortex beam(EVB) carrying orbital angular momentum(OAM) plays a key role in a series of fundamental scientific researches, such as chiral energy-loss spectroscopy and magnetic dichroism spectroscopy. So far, almost all the experimentally created EVBs manifest isotropic doughnut intensity patterns. Here, based on the correlation between local divergence angle of electron beam and phase gradient along azimuthal direction, we show that free electrons can be tailored to EVBs with customizable intensity patterns independent of the carried OAM. As proof-of-concept, by using computer generated hologram and designing phase masks to shape the incident free electrons in the transmission electron microscope, three structured EVBs carrying identical OAM are tailored to exhibit completely different intensity patterns. Furthermore, through the modal decomposition, we quantitatively investigate their OAM spectral distributions and reveal that structured EVBs present a superposition of a series of different eigenstates induced by the locally varied geometries. These results not only generalize the concept of EVB, but also demonstrate an extra highly controllable degree of freedom for electron beam manipulation in addition to OAM.

Divergence angle consideration in energy spread measurement for high-quality relativistic electron beam in laser wakefield acceleration

The thorough exploration of the transverse quality represented by divergence angle has been lacking yet in the energy spread measurement of the relativistic electron beam for laser wakefield acceleration(LWFA). In this work, we fill this gap by numerical simulations based on the experimental data, which indicate that in a C-shape magnet, magnetic field possesses the beam focusing effect, considering that the divergence angle will result in an increase in the full width at half maxima(FWHM) of the electron density distribution in a uniformly isotropic manner, while the length-to-width ratio decreases. This indicates that the energy spread obtained from the electron deflection distance is smaller than the actual value, regardless of the divergence angle. A promising and efficient way to accurately correct the value is presented by considering the divergence angle(for instance, for an electron beam with a length-to-width ratio of 1.12, the energy spread correct from 1.2% to 1.5%), providing a reference for developing the high-quality electron beam source.

Focused electron beam transport through a long narrow metal tube at elevated pressures in the forevacuum range

We present here our investigations of the features of focused electron beam transport in free space at elevated pressures of a few pascals.We have explored the effect of the beam accelerating voltage,operating gas pressure,and magnetic focusing upon the trajectory of beam electrons in the crossover region,in particular on the beam convergence and divergence angles.It is shown that for the forevacuum pressure range of 2-5 Pa explored,a distinctive feature of the propagation of a focused electron beam with a current of up to 20 mA at an accelerating voltage of 10-20 kV is the difference in the angles of convergence(before the focus)and divergence(after the focus).Whereas at a low pressure of 2 Pa the divergence angle is smaller than the convergence angle,as the pressure increases the divergence angle increases and for pressures greater than 5 Pa the divergence angle is greater than the convergence angle.The results obtained were used in experiments on electron beam transport through a long narrow metal tube with a diameter of 5.8-9.2 mm and length of 10-30 cm.We show that for a 30 cm long tube of 7.5 mm diameter,the focused beam transmission can exceed 70%.

Electron beam pumping improves the conversion efficiency of low-frequency photons radiated by perovskite quantum dots

This research argues that using an electron beam with high kinetic energy to pump perovskite quantum dots can significantly boost the efficiency of the low-frequency photon radiation conversion.Firstly,we measure the random lasing threshold and luminescence threshold of CsPbX_(3)films pumped by an electron beam.Then,we simulate the spatial distribution of the electron beams in CsPbX_(3)films.Combined with the above data,a low-frequency photon radiation conversion model based on the electron pumped perovskite quantum dots is presented.This could be a way to create a terahertz source with a high-power output or to multiply the terahertz power.

Effects of anode material on the evolution of anode plasma and characteristics of intense electron beam diode

In this paper,three kinds of materials including graphite,titanium(Ti)and molybdenum(Mo)are used as anodes to figure out the influence factors of anode material on the characteristics of the intense electron beam diode.The results show that the characteristics of diode are mainly determined by the cathode plasma motion under a 15 mm diode gap,in which the typical electron beam parameters are 280 kV,3.5 kA.When the diode gap is reduced to 5 mm,the voltage of the electron beam reduces to about 200 kV,and its current increases to more than 8.2 kA.It is calculated that the surface temperatures of Ti and Mo anodes are higher than their melting points.The diode plasma luminescence images show that Ti and Mo anodes produce plasmas soon after the bombardment of electron beams.Ti and Mo lines are respectively found in the plasma composition of Ti and Mo anode diodes.Surface melting traces are also observed on Ti and Mo anodes by comparing the micromorphologies before and after bombardment of the electron beam.These results suggest that the time of anode plasma generation is closely related to the anode material.Compared with graphite,metal Ti and Mo anodes are more likely to produce large amounts of plasma due to their more significant temperature rise effect.According to the moment that anode plasma begins to generate,the average expansion velocities of cathode and anode plasma are estimated by fitting the improved space-charge limited flow model.This reveals that generation and motion of the anode plasma significantly affect the characteristics of intense electron beam diode.

Local wavelength evolution and Landau damping of electrostatic plasma wave driven by an ultra-relativistic electron beam in dense inhomogeneous plasma

Evolution of an electrostatic plasma wave driven by a low-density ultra-relativistic electron beam in dense inhomogeneous plasma is considered. In particular, the wavelength variation as observed at fixed locations in the plasma is analyzed in terms of the wave characteristics. It is shown that for a negative density gradient, the observed local wavelength decreases monotonically with time, but for a positive density gradient, it first increases and then decreases with time, accompanied by reversal of the wave phase. However, in both cases the local wavelength eventually decreases with time since Landau damping becomes significant as the wavelength becomes of the order of the plasma Debye length. Results from particle-in-cell simulations agree well with theoretical analyses of the wavelength variation.

Controllable growth of wafer-scale PdS and PdS_(2) nanofilms via chemical vapor deposition combined with an electron beam evaporation technique

Palladium(Pd)-based sulfides have triggered extensive interest due to their unique properties and potential applications in the fields of electronics and optoelectronics.However,the synthesis of large-scale uniform PdS and PdS_(2)nanofilms(NFs)remains an enormous challenge.In this work,2-inch wafer-scale PdS and PdS_(2) NFs with excellent stability can be controllably prepared via chemical vapor deposition combined with electron beam evaporation technique.The thickness of the pre-deposited Pd film and the sulfurization temperature are critical for the precise synthesis of PdS and PdS_(2) NFs.A corresponding growth mechanism has been proposed based on our experimental results and Gibbs free energy calculations.The electrical transport properties of PdS and PdS_(2) NFs were explored by conductive atomic force microscopy.Our findings have achieved the controllable growth of PdS and PdS_(2) NFs,which may provide a pathway to facilitate PdS and PdS_(2) based applications for next-generation high performance optoelectronic devices.

Radio Frequency Quadrupole for Bunching Electron Beam: Electromagnetic Field, Particle Velocity Range, and Accuracy at 10 GHz

The Radio Frequency Quadrupole (RFQ) accelerator invented by Kapchinskii and Tepliakov can focus, bunch, and accelerate charged-particle beams simultaneously. Typically, it operates at frequencies up to 500 MHz, for low particle velocities ( β ). The first attempt to design cylindrical RFQ for electrons in the GHz region was done using 3 GHz at Frascati in 1990. In this paper, an analytical approximation of the electromagnetic field is given, and linearized in the beam region for a rectangular Electron Radio Frequency Quadrupole (ERFQ). The differences between the proton-RFQ and the electron-RFQ are discussed. Then, it will be shown that contrary to the quadrupoles for protons or heavy-ions, the ERFQ is suited for electron velocities in the range 0.5 - 0.7 c, and possible applications are given. Finally, it is illustrated, with numerical field computations that this approach gives sufficient accuracy at 10 GHz.

Lifetime measurement of the 3d^(9) ^(2)D_(3/2) metastable level in Mo^(15+)at an electron beam ion trap

An experimental measurement of the lifetime of 3d^(9) ^(2)D_(3/2) metastable level in Mo^(15+)is reported in this work.The Mo^(15+)ions are produced and trapped in an electron beam ion trap with a magnetic field of 0.65 T.The decay photons emitted from 3d^(9) ^(2)D_(3/2) level are subsequently recorded via a cooled photomultiplier tube.Through meticulous scrutiny of potential systematic uncertainties affecting the measurement outcomes,we have determined the lifetime of Mo^(15+)3d^(9)2D_(3/2)metastable level to be 2.83(22)ms.The experimental result provides a clear distinguishment from existing calculations based on various theoretical approaches.

HEPS Achieves the First Electron Beam Accelerated to 500 MeV

The first electron beam of the High Energy Photon Source(HEPS)was accelerated to 500 MeV with better than 2.5 nC of bunch charge by the Linear accelerator(Linac)on March 14,which was a key milestone of the HEPS project–HEPS beam commissioning has since begun.The HEPS Linac,with a total length of about 49 m,is an S-band normal conducting electron linear accelerator with a very high bunch charge and a large bunch charge range.As the source and first-stage accelerator of electrons,the Linac mainly comprises an electron gun,a bunching system,and a main accelerator.

Near-Field Beam Training for Holographic MIMO Communications: Typical Methods, Challenges and Future Directions

Holographic multiple-input multiple-output(HMIMO)has become an emerging technology for achieving ultra-high frequency spectral efficiency and spatial resolution in future wireless systems.The increasing antenna aperture leads to a more significant characterization of the spherical wavefront in near-field communications in HMIMO scenarios.Beam training as a key technique for wireless communication is worth exploring in this near-field scenario.Compared with the widely researched far-field beam training,the increased dimensionality of the search space for near-field beam training poses a challenge to the complexity and accuracy of the proposed algorithm.In this paper,we introduce several typical near-field beam training methods:exhaustive beam training,hierarchical beam training,and multi-beam training that includes equal interval multi-beam training and hash multi-beam training.The performances of these methods are compared through simulation analysis,and their effectiveness is verified on the hardware testbed as well.Additionally,we provide application scenarios,research challenges,and potential future research directions for near-field beam training.

Failure Analysis of Electron Beam Weld Joints for 18Ni Co-free Maraging Steels

Microstructure of two different 18Ni Co-free maraging specimens and their electron beam weld joints were investigated comparatively by optical microscopy and SEM. It is showing that both of the steels are typical lath martensite, however, one grain size is about three times as another one, and XRD reveals that the amount of the retained austenitic phase in the former is less then the latter. The austenite distributes in plate form along granular and lath boundaries while some in fine particle within the matrix. The microstructural difference between two specimens led to diverse behaviors in electron beam welding. The first specimen is weldable well but the second shows obvious welding defects of pits and burn-through holes in weld face. The welding microstructure exhibits a typical dendritic morphology, and the grains in the heat-affected zone recrystallized and grew up obviously for high temperature heated by welding electron beam. The weldablity is relative to the thermal conduction performance of the base materials,which is contributed greatly for grain size and austenite content.

Effects of Electron Beam Local Postweld Heat Treatment on Microstructure and Properties of 30CrMnSiNi2A Steel Welded Joints

To improve the microstructure and properties of the electron beam welded joints, the vacuum or furnace whole post weld heat treatment (FWPWHT) usually should be done on it. The electron beam local post weld heat treatment (EBLPWHT) is a rather new heat treatment procedure that provides the advantages of high precision, flexibility and efficiency, energy saving and higher productivity. In this paper, the microstructure, mechanical properties, fracture toughness and fatigue properties of electron beam welded joints of 30CrMnSiNi2A steel in as-welded (AW) and EBLPWHT conditions have been investigated respectively. The results show that the microstructures of different zones of joints in as-welded condition are changed by EBLPWHT procedure, in which the welds from coarse needle martensite into lath-shaped martensite; the main structures of heat affected zones (HAZ) from lath-shaped martensite into lower bainite. The properties of welded joints can be improved by the EBLPWHT in some extent, especially the fracture toughness of the welds and the fatigue crack resistance of welded joints can be sufficiently improved. However, more appropriate heat treatment parameters of the EBLPWHT have to be studied in order to increase the mechanical properties of base metal near by the HAZ.

3D Finite Element Numerical Simulation of Residual Stresses on Electron Beam Welded BT20 Plates

A three-dimensional finite-element model (FEM) used for calculating electron beam (EB) welding temperature and stresses fields of thin plates of BT20 titanium has been developed in which the nonlinear thermophysical and thermo-mechanical properties of the material has been considered. The welding temperature field, the distributions of residual stresses in as-welded (AW) and electron beam local post-weld heat treatment (EBLPWHT) conditions have been successfully simulated. The results show that: (1) In the weld center, the maximum magnitude of residual tensile stresses of BT20 thin plates of Ti alloy is equal to 60%- 70% of its yield strength σs. (2) The residual tensile stresses in weld center can be even decreased after EBLPWHT and the longitudinal tensile stresses are decreased about 50% compared to joints in AW conditions. (3) The numerical calculating results of residual stresses by using FEM are basically in agreement with the experimental results. Combined with numerical calculating results, the effects of electron beam welding and EBLPWHT on the distribution of welding residual stresses in thin plates of BT20 have been analyzed in detail.

Microstructure and property of the Ti-24Al-15Nb-1.5Mo/TC11 joint welded by electron beam welding

The Ti-24Al-15Nb-1.5Mo alloy, in the as-forged and heat-treated states, was joined to the as-forged TC 11 titanium alloy by electron beam welding with the heat inputs of 135 and 150 kJ/m. Then the microstructure and property of the Ti-24Al-15Nb- 1.5Mo/TC 11 welding interface were investigated. The results show that the phase constitution of the weld is not related to the heat input, and is mainly composed of α＇ phase. Moreover, the intermetallic phases of TiEAlNb, MoNb, NbaAl, and TiAl3 are formed in the weld zone. Therefore, the microhardness value of the weld zone is higher than that of the other portions in the same sample. The profile of the weld is asymmetrically fimnel-like. The grain sizes of the weld and its heat-affected zones are increased with increasing heat input. There is an obvious difference in the element content of the welding interface; only the alloying elements in the fusion zone reach a new balance during solidification.

Beam and image experiment of beam deflection electron gun for distributed X-ray sources

Distributed X-ray sources comprise a single vacuum chamber containing multiple X-ray sources that are triggered and emit X-rays at a specific time and location. This process facilitates an application for innovative system concepts in X-ray and computer tomography. This paper proposes a novel electron beam focusing, shaping,and deflection electron gun for distributed X-ray sources.The electron gun uses a dispenser cathode as an electron emitter, a mesh grid to control emission current, and two electrostatic lenses for beam shaping, focusing, and deflection. Novel focusing and deflecting electrodes were designed to increase the number of focal spots in the distributed source. Two identical half-rectangle opening electrodes are controlled by adjusting the potential of the two electrodes to control the electron beam trajectory, and then, multifocal spots are obtained on the anode target. The electron gun can increase the spatial density of the distributed X-ray sources, thereby improving the image quality. The beam experimental results show that the focal spot sizes of the deflected(deflected amplitude 10.5 mm)and non-deflected electron beams at full width at half maximum are 0.80 mm 90.50 mm and 0.55 mm 90.40 mm, respectively(anode voltage 160 kV; beam current 30 mA). The imaging experimental results demonstrate the excellent spatial resolution and time resolution of an imaging system built with the sources, which has an excellent imaging effect on a field-programmable gate array chip and a rotating metal disk.