Detection of internal crack growth in polyethylene pipe using guided wave ultrasonic testing

Despite the success of guided wave ultrasonic inspection for internal defect detection in steel pipes,its application on polyethylene(PE)pipe remains relatively unexplored.The growth of internal cracks in PE pipe severely affects its pressure-holding capacity,hence the early detection of internal cracks is crucial for effective pipeline maintenance strategies.This study extends the scope of guided wave-based ultrasonic testing to detect the growth of internal cracks in a natural gas distribution PE pipe.Laboratory experiments and a finite element model were planned to study the wave-crack interaction at different stages of axially oriented internal crack growth with a piezoceramic transducer-based setup arranged in a pitch-catch configuration.Mode dispersion analysis supplemented with preliminary experiments was performed to isolate the optimal inspection frequency,leading to the selection of the T(0,1)mode at 50-kHz for the investigation.A transmission index based on the energy of the T(0,1)mode was developed to trace the extent of simulated crack growth.The findings revealed an inverse linear correlation between the transmission index and the crack depth for crack growth beyond 20%crack depth.

Study on Extraction of Oolong Tea Assisted by Ultrasonic Wave and 4C Technique and Its Application

[Objectives]The extraction conditions of formula oolong tea were investigated by an orthogonal experiment.[Methods]The technical conditions were optimized by the 4C method,and the application of formula oolong tea extract in cigarettes was studied.[Results]①In the experimental range,the best sensory evaluation effect of formula oolong tea extract was obtained with extraction conditions of 70%ethanol as extraction solvent,extraction time h,extraction temperature 25℃,and ultrasonic frequency 80 kHz,and follow-up low-temperature concentration,low-temperature sedimentation and low-temperature centrifugation.②The effects of different centrifugal speeds on the quality of formula oolong tea extract were explored.The formula oolong tea extract obtained under the conditions of 3000 r/min and centrifugal time of 10 min showed the best evaluation effect with soft and delicate smoke,rich smoke fragrance,good comfort and refreshing mouthfeel.③The effective aroma components in the formula oolong tea extract were qualitatively analyzed by GC-MS.[Conclusions]This study provides high-quality raw materials and a theoretical basis for the research of independent flavor blending in cigarette industry enterprises.

Optimization of ultrasonic elastography by coded excitation and transmit-side multi-frequency compounding

To improve the quality of ultrasonic elastography, by taking the advantage of code excitation and frequency compounding, a transmitting-side multi-frequency with coded excitation for elastography （TFCCE） was proposed. TFCCE adopts the chirp signal excitation scheme and strikes a balance in the selection of sub-signal bandwidth, the bandwidth overlap and the number of sub-strain image based on theoretical derivation, so as to further improve the quality of elastic image. Experiments have proved that, compared with the other optimizing methods, the elastographyic signal-to-noise ratio（Re-SN） and contrast-to-noise ratio（Re-CN） are improved significantly with different echo signal-to-noise ratios （ReSN） and attenuation coefficients. When ReSN is 50 dB, compared with short pulse, Rc-SN and Re-CN obtained by TFCCE increase by 53% and 143%, respectively. Moreover, in a deeper investigation （85-95 mm）, the image has lower strain noise and clear details. When the attenuation coefficient is in the range of 0-1 dB/（cm.MHz）, Re-SN and Re-CN obtained by TFCCE can be kept in moderate ranges of 5〈Re-SN〈6.8 and 11.4〈Re-CN〈15.2, respectively. In particular, for higher tissue attenuation, the basic image quality cannot be ensured with short pulse excitation, while mediocre quality strain figure can be obtained by TFCCE. Therefore, the TFCCE technology can effectively improve the elastography quality and can be applied to ultrasonic clinical trials.

THE EQUIVALENT CIRCUIT AND CONTROL SYSTEM OF TRAVELLING WAVE TYPE ULTRASONIC MOTOR

The ultrasonic motor is a sort of new type of micromotor with special structure. By use of piezoelectric converse effect of ceramics, the electrical energy is transformed into mechanical energy. Its operating principle is quite different from that of the traditional motors. In this paper the equivalent circuits of the ring stator and even the whole motor are proposed after studying the equivalent circuit of piezoelectric vibrator. Then the paper makes detailed analyses of each part of the control system, which has been simplified by the equivalent circuit. The theory in this paper has been proved through experiments.

Dynamic Rangefinding Device Using Amplitude-Modulated Continuous UltrasonicWave+

Aim To develop a high speed and high resolution dynamic rangefinding device for the measurement of large distances.Methods The device was comprised of an ultrasonic transmitter and a receiver,and a receiver , and a continuous ultrasonic wave amplitude-modulated by a low- frequency acoustic signal was used. The rangefinding was achieved by detecting the phase difference between the transmitted and received ultrasonic signals. The design principle. hard- ware implementation , experimental results and performance analysis of the device are included. Results and Conclusion Experiments show that the accuracy of the device are included. within 1.5m while its dynamic data update rate can be up to 40kHz.

Speed Control of Travelling Wave Type Ultrasonic Motors Using Artificial Neural Network

Ultrasonic motor (USM) is a newly developed motor, and it has some excellent performances and useful features, therefore, it has been expected to be of practical use. However, the driving principle of USM is different from that of other electromagnetic type motors, and the mathematical model is complex to apply to motor control. Furthermore, the speed characteristics of the motor have heavy nonlinearity and vary with driving conditions. Hence, the precise speed control of USM is generally difficult. This paper proposes a new speed control scheme for USM using an artificial neural network. An accurate tracking response can be obtained by random initialization of the weights of the network owing to the powerful on line learning capability. Two prototype ultrasonic motors of travelling wave type were fabricated, both having 100 mm outer diameters of stator and piezoelectric ceramic. The usefulness and validity of the proposed control scheme are examined in experiments.

Digital core based transmitted ultrasonic wave simulation and velocity accuracy analysis

Transmitted ultrasonic wave simulation （TUWS） in a digital core is one of the important elements of digital rock physics and is used to study wave propagation in porous cores and calculate equivalent velocity. When simulating wave propagates in a 3D digital core, two additional layers are attached to its two surfaces vertical to the wave-direction and one planar wave source and two receiver-arrays are properly installed. After source excitation, the two receivers then record incident and transmitted waves of the digital rock. Wave propagating velocity, which is the velocity of the digital core, is computed by the picked peak-time difference between the two recorded waves. To evaluate the accuracy of TUWS, a digital core is fully saturated with gas, oil, and water to calculate the corresponding velocities. The velocities increase with decreasing wave frequencies in the simulation frequency band, and this is considered to be the result of scattering. When the pore fluids are varied from gas to oil and finally to water, the velocity-variation characteristics between the different frequencies are similar, thereby approximately following the variation law of velocities obtained from linear elastic statics simulation （LESS）, although their absolute values are different. However, LESS has been widely used. The results of this paper show that the transmission ultrasonic simulation has high relative precision.

Temperature Dependence of Ultrasonic Longitudinal Guided Wave Propagation in Long Range Steel Strands

Ultrasonic guided wave inspection is an effective non-destructive testing method which can be used for stress level evaluation in steel strands.Unfortunately the propagation velocity of ultrasonic guided waves changes due to temperature shift making the prestress measurement of steel strands inaccurate and even sometimes impossible.In the course of solving the problem,this paper reports on quantitative research on the temperature dependence of ultrasonic longitudinal guided wave propagation in long range steel strands.In order to achieve the generation and reception of a chosen longitudinal mode in a steel strand with a helical shaped surface,a new type of magnetostrictive transducer was developed,characterized by a group of thin clips and three identical permanent magnets.Excitation and reception of ultrasonic guided waves in a steel strand were performed experimentally.Experimental results shows that in the temperature range from-4 ℃ to 34 ℃,the propagation velocity of the L（0,1） mode at 160 kHz linearly decreased with increasing temperature and its temperature dependent coefficient was 0.90（m·s-1 ·（℃）-1） which is very close to the theoretical prediction.The effect of dimension deviation between the helical and center wires and the effect of the thermal expansion of the steel strand on ultrasonic longitudinal guided wave propagation were also analyzed.It was found that these effects could be ignored compared with the change in the material mechanical properties of the steel strands due to temperature shift.It was also observed that the longitudinal guided wave mode was somewhat more sensitive to temperature changes compared with conventional ultrasonic waves theoretically.Therefore,it is considered that the temperature effect on ultrasonic longitudinal guided wave propagation in order to improve the accuracy of stress measurement in prestressed steel strands.Quantitative research on the temperature dependence of ultrasonic guided wave propagation in steel strands provides an important basis for the compensation of temperature effects in stress measurement in steel strands by using ultrasonic guided wave inspection.

Contact Analysis and Modeling of Standing Wave Linear Ultrasonic Motor

A contact model for describing the contact mechanics between the stator and slider of the standing wave linear ultrasonic motor was presented. The proposed model starts from the assumption that the vibration characteristics of the stator is not affected by the contact process. A modified friction models was used to analyze the contact problems. Firstly, the dynamic normal contact force, interface friction force, and steady-state characteristics were analyzed. Secondly, the influences of the contact layer material, the dynamic characteristics of the stator, and the pre-load on motor performance were simulated. Finally, to validate the contact model, a linear ultrasonic motor based on in-plane modes was used as an example. The corresponding results show that a set of simulation of motor performances based on the proposed contact mechanism is in good agreement with experimental results. This model is helpful to understanding the operation principle of the standing wave linear motor and thus contributes to the design of these types of motor.

A Novel Traveling Wave Ultrasonic Motor Using a Bar Shaped Transducer

A novel traveling wave ultrasonic motor was proposed. The structure of the motor is rather simple and different from the conventional traveling wave ultrasonic motors. Its production processes are very convenient. It is composed of a stator constituted with a ring and a bar shaped transducer and two cone shaped rotors. The rotors were pressed on inner surface of the ring by means of a pre-pressure system. The bar shaped transducer has a sand- wich-like configuration,where two sets of piezoelectric element are bolted. One set excites a longitudinal vibration of the bar, and the other set excites a flexural vibration of the bar. The ring＇s traveling wave excited with the longitudinal vibration and the bending vibration of the bar transducer was simulated with FEM （finite element method）. The prototype of the motor was made and investigated experimentally for its performance. Its maximum torque and rotating speed are 0.25 N · m and 50 r/min, respectively.

High Precision Ultrasonic Guided Wave Technique for Inspection of Power Transmission Line

Due to the merits of high inspection speed and long detecting distance, Ultrasonic Guided Wave（UGW） method has been commonly applied to the on-line maintenance of power transmission line. However, the guided wave propagation in this structure is very complicated, leading to the unfavorable defect localization accuracy. Aiming at this situation, a high precision UGW technique for inspection of local surface defect in power transmission line is proposed. The technique is realized by adopting a novel segmental piezoelectric ring transducer and transducer mounting scheme, combining with the comprehensive characterization of wave propagation and circumferential defect positioning with multiple piezoelectric elements. Firstly, the propagation path of guided waves in the multi-wires of transmission line under the proposed technique condition is investigated experimentally. Next, the wave velocities are calculated by dispersion curves and experiment test respectively, and from comparing of the two results, the guided wave mode propagated in transmission line is confirmed to be F（1,1） mode. Finally, the axial and circumferential positioning of local defective wires in transmission line are both achieved, by using multiple piezoelectric elements to surround the stands and send elastic waves into every single wire. The proposed research can play a role of guiding the development of highly effective UGW method and detecting system for multi-wire transmission line.

Ultrasonic focusing and scanning with multiple waves

This paper presents a new focusing and scanning method which focuses multiple waves on a target. The key of the method is to control excitation pulses for each element of the transducer array. The excitation pulse on each array element is obtained by time reversing the signal received by the same element, which is generated by an imaginary source at the target. The excitation pulses from all array elements are transmitted and arrive at the target simultaneously, and focusing is achieved. The performance of the two methods is compared in numerical examples, and it is demonstrated that the proposed method achieves a satisfactory focusing and a good signal-to-noise ratio no matter where the target location is.

Working principle and design of a double cylinders type traveling wave ultrasonic motor using composite transducer

A double cylinders type traveling wave ultrasonic motor using composite transducer was proposed.The proposed stator contained two cylinders and one composite transducer,and the transducer located on the outer surfaces of cylinders.The composite transducer included two exponential horns located on leading ends,and the horns insected with the cylinders at tip ends.Two degenerated flexural vibration modes spatially and temporally orthogonal to each other were excited in each cylinder by the composite transducer.In this new design,a single transducer could excite two flexural traveling waves in the cylinders.Thus,elliptical motions were achieved at the particles on the teeth.The working principle of the proposed motor was analyzed.The cylinder and transducer were designed with FEM.The resonant frequencies of two vibration modals of the stator were tuned to be the same,and the motion trajectories of nodes on the teeth were analyzed.Transient analysis results show that the motion trajectories of teeth are ellipses.The results of this paper can guide the development of this new type of ultrasonic motor.

Effect of Filler Composition on the Brazing of Alumina to Copper Using Ultrasonic Wave

An ultrasonic wave was applied during brazing of alumina to Cu. First alumina was metallized by applying ultrasonicwave in braze bath. Then the metallized alumina was brazed with Cu using the same filler alloy. The filler used wereZn-Al alloys and Zn-Sn Alloys. The weight percent of Al in filler was ranging between 0, 5%, 10%, respectively.The weight percent of tin in filler was ranging between 0, 30%, 60% and 91%, respectively. The joining mechanismwas investigated by measuring the joining strength, hardness and analyzing the microstructure at interface of thejoint. The shear strength and microstructure of the joint strongly depend on the filler composition. The effect ofultrasound was derived primarily from acoustic cavitations, impact and friction of the filler against alumina ceramic.This improved the wetting between alumina and the filler, and reflected to improve the joint strength. Anotherultrasonic advantage as to reduce of the joining temperature, that reduced the thermal stress in the braze joint.

EFFECT OF ULTRASONIC WAVE ON THE ELECTROPOLYMERIZATION OF PYRROLE

Electropolymerization of pyrrole under ultrasonic field at 20kHz was performed in a series of aqueous and propylene carbonate (PC) solutions. The ultrasonic wave with moderate intensity at the power of 44W, which is the power threshold of the ultrasonic generator used in this work to produce cavitation effect, enhance the conductivity and tensile strength of the polypyrrole films as prepared. However, too high intensity of the ultrasonic wave is harmful to the polymerization.

Non-contact evaluation of the resonant frequency of a microstructure using ultrasonic wave

This paper presents a novel non-contact method for evaluating the resonant frequency of a microstructure, Firstly, the microstructure under test is excited by ultrasonic waves. This excitation method does not impose any undefined load on the specimen like the electrostatic excitation and also this is the first actual use of ultrasonic wave for exciting a microstructure in the literature. Secondly, the amplitudes of the microstructure are determined by image edge detection using a Mexican hat wavelet transform on the vibrating images of the microstructure. The vibrating images are captured by a CCD camera when the microstructure is vibrated by ultrasonic waves at a series of discrete high frequencies （〉30 kHz）. Upon processing the vibrating images, the amplitudes at various excitation frequencies are obtained and an amplitude-frequency spectrum is obtained from which the resonant frequency is subsequently evaluated. A micro silicon structure consisting of a perforated plate （192 × 192 μm） and two cantilever beams （76 × 43 μm） which is about 4 μm thickness is tested. Since laser interferometry is not required, thermal effects on a test object can be avoided. Hence, the setup is relatively simple. Results show that the proposed method is a simple and effective approach for evaluating the dynamic characteristics of microstructures.

Determination of the parameters of a linear-viscoelastic thin layer using the normally-incident ultrasonic waves

This paper proposes a method of simultaneous determination of the four layer parameters （mass density, longitudinal velocity, the thickness and attenuation） of an immersed linear-viscoelastic thin layer by using the normally-incident reflected and transmitted ultrasonic waves. The analytical formula of the layer thickness related to the measured trans- mitted transfer functions is derived. The two determination steps of the four layer parameters are developed, in which acoustic impedance, time-of-flight and attenuation are first determined by the reflected transfer functions. Using the derived formula, it successively calculates and determines the layer thickness, longitudinal velocity and mass density by the measured transmitted transfer functions. According to the two determination steps, a more feasible and simplified measurement setups is described. It is found that only three signals （the reference waves, the reflected and transmitted waves） need to be recorded in the whole measurement for the determination of the four layer parameters. A study of the stability of the determination method against the experimental noises and the error analysis of the four layer parameters are made. This study lays the theoretical foundation of the practical measurement of a linear-viscoelastic thin layer.

Application of Ultrasonic Waves for the Improvement of Water Treatment

Application of ultrasonic waves is one of the novel techniques for the improvement of water treatment process. In this study, ultrasonic waves were irradiated to drinking water for water softening process and other contaminants removal. The experimental results showed that this technique improved the water treatment process efficiently. The study also revealed that the various parameters such as amplitude, frequency and irradiation time could affect the efficiency of ultrasound techniques for the improvement of water quality.

Defect detection in brazed weldment with lattice structure using ultrasonic Lamb wave technique

In this paper, defects detection in brazed weldment with lattice structure is studied using ultrasonic Lamb wave. Based on the ultrasonic guided wave theory, the frequency dispersion curves for phase and group velocity of I Cr18Ni9Ti are obtained by solving the Rayleigh-Lamb equation. The incident angles of different modes are determined through theoretical calculation and experimental analyses. Artificial defects of through-wall slots with different dimensions are made and tested. Experimental scattering effects of the fundamental symmetric mode S2 and asymmetric modes A1 and A0 are analysed and compared. The results show that mode Ao is suitable for detecting artificial defect, and the amplitude of the received signals are in good agreement with the defect size. Brazed weldment specimen containing lack of brazing with certain dimensions is made. Using the same methodology, scattering effects produced by weld defects are measured. The results show that the clutter wave brought about by the filler metal will certainly disturbs the identification of defect signal. But, when the defect is 3.0 mm in width, the presented mode Ao could be used potentially.

Selective generation of ultrasonic Lamb waves by electromagnetic acoustic transducers

In this paper, we describe a modal expansion approach for the analysis of the selective generation of ultrasonic Lamb waves by electromagnetic acoustic transducers （EMATs）. With the modal expansion approach for waveguide excitation, an analytical expression of the Lamb wave＇s mode expansion coefficient is deduced, which is related to the driving frequency and the geometrical parameters of the EMAT＇s meander coil, and lays a theoretical foundation for exactly analyzing the selective generation of Larnb waves with EMATs. The influences of the driving frequency on the mode expansion coefficient of ultrasonic Lamb waves are analyzed when the EMAT＇s geometrical parameters are given. The numerical simulations and experimental examinations show that the ultrasonic Lamb wave modes can be effectively regulated （strengthened or restrained） by choosing an appropriate driving frequency of EMAT, with the geometrical parameters given. This result provides a theoretical and experimental basis for selectively generating a single and pure Lamb wave mode with EMATs.