Soft-switching Grid-connected PV Inverter With Interleaved Flyback Topology

提出一种应用于单个光伏组件的软开关交错反激并网逆变器拓扑及其软开关控制策略。针对反激变压器漏感问题，提出漏感能量吸收回馈电路，实现了漏感能量吸收再利用，并实现了开关管漏源电压的钳位，提高了变换效率同时降低了开关管关断电压尖峰；提出基于数字处理器的反激变换器变开关频率谐振软开关控制策略，实现了开关管的零电压开通，同时改善了逆变器的电磁兼容特性；提出的交错并联反激逆变器有助于减小变压器和滤波器的体积，提高功率密度。详细分析变换器的工作原理，分析变开关频率谐振软开关控制方式的原理和实现条件，最后进行实验验证。

Single Current Feedback Control Strategy for Grid-connected Inverters With LCL Filters

LCL滤波器广泛应用于并网逆变器系统中,其对高次谐波具有良好的衰减作用;但LCL滤波器为低阻尼三阶系统,容易发生谐振。传统的有源阻尼方法,通过对电容电流进行采样并反馈,能够抑制系统振荡,但增加了传感器数量。提出一种单电流反馈控制策略,其采用入网电流两次微分的反馈方法,增加了系统阻尼,从而有效地抑制LCL滤波器的谐振尖峰,保证系统的稳定性;同时其对系统参数不敏感,并且不增加额外的传感器,是一种低成本高可靠性的控制策略。文中推导该控制策略下的系统传递函数,并分析系统的稳定性。最后,通过仿真和实验,验证提出的控制策略的可行性与有效性。

H6 Non-isolated Full Bridge Grid-connected PV Inverters With Low Leakage Currents

为满足非隔离光伏并网发电系统对共模漏电流的限制，提出一种六开关逆变器拓朴（H6拓扑）。所提出的H6拓扑在功率传输模态时，进网电流半个工频周期流过3支开关管，而另半个工频周期流过2支开关管，故相对于H5拓扑，降低了通态损耗，有利于热应力均衡，且仍满足续流阶段光伏电池输出端与电网脱离的要求。详细分析拓扑的工作原理，并推论给出H6非隔离光伏并网逆变器的其它3种拓扑结构；比较分析了H5拓扑、Heric拓扑和H6拓扑的损耗和成本。通过1kW通用样机平台对比验证了上述3种拓扑的效率和共模特性。实验结果表明，H6拓扑的变换效率高于H5拓扑、但略低于Heric拓扑，共模特性优于Heric拓扑、但略劣于H5拓扑。

A Control Strategy for Grid-connected Inverters With LCL Filters

把LCL滤波器作为电压源型并网逆变器与电网的接口已受到广泛关注。与单电感L滤波器相比，利用电感值较小的LCL滤波器对入网电流的高次谐波具有显著的衰减效果，特别是在低开关频率的大功率并网逆变系统应用中更具明显优势，但是仅采用直接入网电流控制时，LCL滤波器接口的并网逆变器系统存在稳定性问题。该文采用电网侧电感电流和逆变侧电感电流双闭环控制策略对并网电流进行直接控制，电网侧电感电流作为外环更容易抑制并网电流的谐波因素，且可以直接控制入网电流的单位功率因数，采用逆变器侧电感电流作为内环可以增加系统阻尼，从而可抑制系统振荡，增加系统稳定性。对该方案进行系统建模，并深入分析了滤波器参数、控制器参数及系统稳定性之间的精确量化关系。仿真和实验结果表明，该控制策略既可有效抑制入网电流谐振和实现进网电流的高功率因数运行，同时又具有良好的稳态和动态性能。

A New Predictive Direct Power Control Solution for Three-phase Grid-Connected Inverters

This paper proposes a new Predictive Direct Power Control(P-DPC) solution for three-phase grid-connected inverters, which combines direct power control strategy with the predictive control strategy and space vector pulse width modulation(SVPWM), obtaining both high transient performance and a constant switching frequency. This control solution can achieve decoupling control for active and reactive power and an adjustable power factor. Meanwhile, the grid-connected current can approximately be sinusoidal. The feasibility and advantages of the control strategy are verified by the simulation and experiment compared with another existing P-DPC.

Grid-connected inverter for wind power generation system

In wind power generation system the grid-connected inverter is an important section for energy conversion and transmission, of which the performance has a direct influence on the entire wind power generation system. The mathematical model of the grid-connected inverter is deduced firstly. Then, the space vector pulse width modulation （SVPWM） is analyzed. The power factor can be controlled close to unity, leading or lagging, which is realized based on H-type current controller and grid voltage vector-oriented control. The control strategy is verified by the simulation and experimental results with a good sinusoidal current, a small harmonic component and a fast dynamic response.

Extended Quality Characterization of Grid Connected PV Inverters

The overall performance of photovoltaic （PV） inverter imphes many different technical issues.One of the key criterias is based on the measurement of the conversion and the maximum power point tracking （MPPT） efficiency and its applicable evaluation in practice.Intense work has been done in the last few years to formulate applicable standards for measuring static and dynamic efficiencies worldwide.Besides that,this work is presenting on novel methods of analysis on non-trivial system characteristics impacting the final evaluation on the overall performance of the PV inverter.The elaborated testing procedures for complex system behavior under highly nonlinear conditions （unintentional partial shading, mismatching of DC strings） are explained and characterized.With the help of experimental results, the exclusive impact on the overall efficiency is illustrated and helpful statements are given on the resulting technical characteristics of MPP strategies.

A Pathway to Explore the Hidden Specialty in the Design of Fifteen Level Inverter in Grid Connected PV System

This research paper proposes a single phase fifteen level inverter for a grid connected PV system.The proposed inverter is also called cascaded asymmetric multilevel inverter.By adopting appropriate hybrid modulation technique improved output voltage is obtained with minimum number of power electronic switches.By reducing the number of gate triggering circuits of the switches,the size and power consumption of the driving circuits can be reduced.The total harmonic distortion of the output of the inverter is improved by this inverter.The proposed inverter developed by cascading a full bridge inverter with modified H bridge multilevel inverter.The validity of the proposed system is verified through MATLAB simulations.

Simulation and Analysis of a Multilevel Converter Topology for Solar PV Based Grid Connected Inverter

There has been a noticeable increase in use of Solar PV based systems for power generation, given its renewable nature. A solar PV based grid tie inverters are used for dc-ac conversion. The conventional line commutated ac-to-dc inverters have square-shaped line current which contains higher-order harmonics. The line current with the high harmonic contents generates EMI and moreover it causes more heating of the core of distribution/power transformers. Alternatively, PWM based inverters using MOSFET/IGBT switches are also used for the same purpose. However, apart from higher switching losses, the power handling capability and reliability of these devices are quite low in comparison to thyristors/SCR. Nevertheless, the conventional thyristor based forced commutated inverters are not suitable for PWM applications due to the problems of commutation circuits. A pure sinusoidal line current or waveform with low har- monic contents is the most desirable. In the present work, a multilevel line commutated inverter topology has been proposed and analyzed which improves the wave shape and hence reduces the total harmonic distortion (THD) of the line current in a grid tie line commutated inverter. The scheme has successfully been implemented and tested. Moreover, the performance of the proposed topology is far better than the conventional line-commutated inverter. It reduces THD, losses, switching stress and EMI.

Topology for current-source grid-connected inverter with improved effciency and pulse width modulation control strategy

A novel topology of the current-source grid-connected inverter is proposed based on the immittance converter theory. A control strategy of sine-sine pulse width modulation （PWM） is studied. Compared with the traditional current-source inverter, the power frequency inductors and power frequency transformer are replaced with high frequency inductors and a high frequency transformer. Thus, the proposed inverter has advantages of small volume, low cost, low total harmonic distortion （THD）, low power losses, high power factor （PF） and simple control. Furthermore, grid voltage cannot influence output current of the grid-connected inverter and the current-source inverter with a high PF that approaches one has been realized. Finally, validity of the theory analysis and feasibility of the control scheme are shown by simulation and experimental results.

Research and Design of Inverter Applied in Solar PV Systems Connected to Distribution Grid

This paper presents the results of research on the application of inverter in the grid connected solar photovoltaics (PV) system. The main content of the article is to control the three-phase grid connected inverter to meet the requirement of controlling the reactive power to zero at a node of the distribution network while maximizing the active power transmitted to the grid. The control circuits are synthesized on the dq coordinate system and verified on the simulation model by Matlab/Simulink. Both simulation and experimental prototype on 5 kW inverter, being connected to low voltage grid, have been built to show the good results and the practical readiness for implementation.

Dual-loop Control Strategy for Grid-connected Inverter with LCL Filter

As to the concrete topology of three-phase LCL type grid-connected inverter with damping resistance, mathematical model was deduced in detail, using method of equivalent transformation to the structure diagram, damping resistance was virtualized, mathematical model under the DQ frame that can realize decoupling control was established, a dual-loop control strategy for grid-connected inverter with LCL filter was proposed, the system stability was analyzed and the design method of controller was given. The proposed method overcame the flaws of loss increase, efficiency reduce and cost increase which were caused by damping resistance in LCL type grid-connected inverter, the system efficiency and power supply quality of the output were improved. Feasibility and effectiveness of the new method were validated by simulation and experimental results.

Comparison the Performances of Three Earthing Systems for Micro-Grid Protection during the Grid Connected Mode

This paper presents, tests and compares three earthing systems (TT, TN and IT) for Micro-Grid (MG) protection against various fault types during the connected mode. The main contribution of this work is including the models of all the micro sources which interfaced to the MG by power electronic inverters. Inverters in turns are provided with current limiters and this also included in the inverter models to exactly simulate the real situation in the MG during fault times. Results proved that the most suitable earthing system for MG protection during the connecting mode is the TN earthing system. That system leads to a suitable amount of fault current sufficient to activate over current protection relays. With using TN system, Touch voltages at the faulted bus and all other consumer’s buses are less than the safety limited value if current limiter is included with the transformer of the main grid which connects MG. For the two others earthing systems (TT and IT), fault current is small and nearly equal to the over load current which make over current protection relay can not differentiate between fault current and overload current. All models of micro sources, earthing systems, inverters, main grid and control schemes are built using Matlab?/Simulink? environment.

A Review of Novel Leakage Current Suppression Techniques for Transformerless Photovoltaic Inverters

漏电流抑制是无变压器型光伏并网系统需要解决的关键问题之一。VDE-0126-1-1标准规定,漏电流高于300 mA时光伏并网系统必须在0.3 s内从电网中切除。为了解释漏电流的根源,建立系统共模电压数学模型,在此基础上分析漏电流产生的原因,探讨不同调制策略对漏电流的影响,然后介绍几种典型的、能够有效抑制漏电流的电路拓扑结构,并分析各种拓扑的工作原理和特点。最后对漏电流抑制技术方面的发展趋势做了展望。

Power Transfer of PV Inverter from DC to AC Voltage Source

This paper presents a simple approach of a topology already known in the literature, applied in active power transfer from direct current source to any alternating current voltage source, whether the utility power or a voltage inverter that is forming an isolated AC grid. The photovoltaic inverter works as current controlled voltage source inverter that provides a sinusoidal current to the AC grid. The inverter is insulated from the grid by a transformer. The system is discussed and modeled. Simulation results of this application are presented and experimental results validate this topology.

高渗透率下基于并网逆变器阻抗重塑的锁相环设计方法

针对锁相环、电网阻抗与并网逆变器相互耦合所引发的系统稳定性下降问题。首先,建立考虑电网阻抗的锁相环控制结构模型,通过分析锁相环闭环传递函数可知,电网阻抗会使锁相环系统产生右半平面闭环极点,严重影响锁相环与逆变器系统的稳定性。其次,通过分析逆变器系统输出阻抗,说明锁相环所引入的负阻抗是逆变器系统稳定裕度下降的主要原因。鉴于此,该文提出一种新型锁相环设计方法,理论分析表明,所提方法既能够保证高渗透率下锁相环具有高鲁棒性,又能够对逆变器系统输出阻抗进行重塑,有效拓宽系统对电网阻抗的适应范围。最后,通过仿真与实验验证所提新型锁相环设计方法的有效性。

弱电网下基于电网电压前馈的并网逆变器阻抗重塑控制策略

弱电网下,锁相环在基波以上频段引入的负阻特性,会降低系统输出阻抗的相位,严重影响系统稳定性。鉴于此,该文通过系统控制框图等效变换,推导得到可以消除锁相环负阻特性的电网电压前馈函数,进而提出一种基于电网电压前馈控制的并网逆变器阻抗重塑控制策略。同时,为了提高该策略的普适性,该文利用函数近似和多目标约束为电网电压前馈函数的优化提供两种设计方法,并从系统基波电流跟踪性能、并网功率因数等方面进行误差分析,从而证明其函数优化设计方法的可行性。理论分析表明,优化后的电网电压前馈控制策略,可以有效地对系统输出阻抗相位特性进行重塑,很大程度上拓宽了系统对电网阻抗的适应范围。最后,通过仿真与实验验证所提控制策略的有效性。

基于电路等效的并网逆变器失稳分析与稳定控制

以并网逆变器为功率接口的新能源发电系统在弱电网条件下易发生振荡失稳问题。该文将并网逆变器的控制回路可视化为电路元件组成的虚拟阻抗,基于该电路模型分析了弱电网条件下电流内环与锁相环交互作用导致并网逆变器振荡失稳的机理,在此基础上,提出了基于有源阻尼的稳定控制设计方法,并对不同有源阻尼控制的电路特性以及稳定性提升能力进行了对比分析。研究结果表明,针对锁相环引入负电阻造成的振荡失稳问题,阻抗-高通滤波器型有源阻尼控制策略具有更优的稳定性提升能力。最后通过PSCAD/EMTDC仿真和远宽StarSim控制器硬件在环实验对比了不同有源阻尼控制策略的振荡抑制效果,并验证了阻抗-高通滤波器型有源阻尼控制的动态性能。结果表明,所设计的稳定控制能够在200 ms内有效抑制系统振荡,并且可实现在短路比为1的极弱电网条件下稳定运行。

基于暂态导数极性分段优化的VSG二次调频控制策略

二次调频能使电力系统在一次调频过程中始终满足频率稳定的要求。采用虚拟同步发电机VSG控制策略的并网逆变器在离网运行时仅具备一次调频特性,若VSG的输出频率超出安全工作区间时将会对微电网的稳定运行产生影响,因此,需在有功控制环加入固定积分系数来实现频率无差控制的二次调频,但传统二次调频存在恢复时间与频率振荡的固有矛盾。提出一种根据暂态导数极性分段优化的改进VSG二次调频策略,该策略基于频率恢复特性,将频率恢复过程划分为2个阶段,并分别配置不同的积分系数,使得整个频率恢复时间缩短,且避免了频率的振荡,并给出了所提方法关键参数的设定依据。最后通过仿真与基于HIL的半实物平台验证了所提策略的可靠性。