Fault Identification for Shear-Type Structures Using Low-Frequency Vibration Modes

Shear-type structures are common structural forms in industrial and civil buildings,such as concrete and steel frame structures.Fault diagnosis of shear-type structures is an important topic to ensure the normal use of structures.The main drawback of existing damage assessment methods is that they require accurate structural finite element models for damage assessment.However,for many shear-type structures,it is difficult to obtain accurate FEM.In order to avoid finite elementmodeling,amodel-freemethod for diagnosing shear structure defects is developed in this paper.This method only needs to measure a few low-order vibration modes of the structure.The proposed defect diagnosis method is divided into two stages.In the first stage,the location of defects in the structure is determined based on the difference between the virtual displacements derived from the dynamic flexibility matrices before and after damage.In the second stage,damage severity is evaluated based on an improved frequency sensitivity equation.Themain innovations of this method lie in two aspects.The first innovation is the development of a virtual displacement difference method for determining the location of damage in the shear structure.The second is to improve the existing frequency sensitivity equation to calculate the damage degree without constructing the finite elementmodel.Thismethod has been verified on a numerical example of a 22-story shear frame structure and an experimental example of a three-story steel shear structure.Based on numerical analysis and experimental data validation,it is shown that this method only needs to use the low-order modes of structural vibration to diagnose the defect location and damage degree,and does not require finite element modeling.The proposed method should be a very simple and practical defect diagnosis technique in engineering practice.

Experimental study of solid-liquid origami composite structures with improved impact resistance

In this paper,a liquid-solid origami composite design is proposed for the improvement of impact resistance.Employing this design strategy,Kresling origami composite structures with different fillings were designed and fabricated,namely air,water,and shear thickening fluid(STF).Quasi-static compression and drop-weight impact experiments were carried out to compare and reveal the static and dynamic mechanical behavior of these structures.The results from drop-weight impact experiments demonstrated that the solid-liquid Kresling origami composite structures exhibited superior yield strength and reduced peak force when compared to their empty counterparts.Notably,the Kresling origami structures filled with STF exhibited significantly heightened yield strength and reduced peak force.For example,at an impact velocity of 3 m/s,the yield strength of single-layer STF-filled Kresling origami structures increased by 772.7%and the peak force decreased by 68.6%.This liquid-solid origami composite design holds the potential to advance the application of origami structures in critical areas such as aerospace,intelligent protection and other important fields.The demonstrated improvements in impact resistance underscore the practical viability of this approach in enhancing structural performance for a range of applications.

AN EFFICIENT ASSESSMENT METHOD FOR INTELLIGENT DESIGN RESULTS OF SHEAR WALL STRUCTURE BASED ON MECHANICAL PERFORMANCE,MATERIAL CONSUMPTION,AND EMPIRICAL RULES

Efficient methods for incorporating engineering experience into the intelligent generation and optimization of shear wall structures are lacking,hindering intelligent design performance assessment and enhancement.This study introduces an assessment method used in the intelligent design and optimization of shear wall structures that effectively combines mechanical analysis and formulaic encoding of empirical rules.First,the critical information about the structure was extracted through data structuring.Second,an empirical rule assessment method was developed based on the engineer's experience and design standards to complete a preliminary assessment and screening of the structure.Subsequently,an assessment method based on mechanical performance and material consumption was used to compare different structural schemes comprehensively.Finally,the assessment effectiveness was demonstrated using a typical case.Compared to traditional assessment methods,the proposed method is more comprehensive and significantly more efficient,promoting the intelligent transformation of structural design.

Horizontal structure of convergent wind shear associated with sporadic E layers over East Asia

At present,the main detection instruments for observing sporadic E(Es)layers are ground-based radars,dense networks of ground-based global navigation satellite system(GNSS)receivers,and GNSS radio occultation,but they cannot capture the whole picture of the horizontal structure of Es layers.This study employs the Whole Atmosphere Community Climate Model with thermosphere and ionosphere eXtension model(WACCM-X 2.1)to derive the horizontal structure of the ion convergence region(HSICR)to explore the shapes of the large-scale Es layers over East Asia for the period from June 1 to August 31,2008.The simulation produced the various shapes of the HSICRs elongated in the northwest-southeast,northeast-southwest,or composed of individual small patches.The close connection between Es layer critical frequency(foEs)and vertical ion convergence indicates that the HSICR is a good candidate for revealing and explaining the horizontal structure of the large-scale Es layers.

Multi-layer structure formation of relativistic electron beams in plasmas

A two-dimensional electromagnetic particle-in-cell simulation model is proposed to study the density evolution and collective stopping of electron beams in background plasmas.We show here the formation of the multi-layer structure of the relativistic electron beam in the plasma due to the different betatron frequency from the beam front to the beam tail.Meanwhile,the nonuniformity of the longitudinal wakefield is the essential reason for the multi-layer structure formation in beam phase space.The influences of beam parameters(beam radius and transverse density profile)on the formation of the multi-layer structure and collective stopping in background plasmas are also considered.

Three dimensional shear wave velocity structure of crust and upper mantle in South China Sea and its adjacent regions by surface waveform inversion

We assembled approximately 328 seismic records. The data set was from 4 digitally recording long-period and broadband stations of CDSN. We carried out the inversion based on the partitioned waveform inversion (PWI). It partitions the large-scale optimization problem into a number of independent small-scale problems. We adopted surface waveform inversion with an equal block (2((2() discretization in order to acquire the images of shear velocity structure at different depths (from surface to 430 km) in the crust and upper-mantle. The resolution of all these anomalies has been established with (check-board( resolution tests. These results show significant difference in velocity, lithosphere and asthenosphere structure between South China Sea and its adjacent regions.

Microstructure and shear strength of the brazed joint of Ti(C,N)-based cermet to steel

Firm joins were obtained between Ti（C,N）-based cermet and steel with Ag-Cu-Zn-Ni filler metal by vacuum brazing. The effects of technological parameters such as brazing temperature, holding time, and filler thickness on the shear strength of the joints were investigated. The microstructure of welded area and the reaction products of the filler metal were examined by scanning electron microscopy （SEM）, metallographic microscope （OM）, energy-dispersive X-ray analysis （EDS）, and X-ray diffraction （XRD）. The brazing temperature of 870℃, holding time of 15 min, and filler thickness of 0.4 mm are a set of optimum technological parameters, under which the maximum shear strength of the joints, 176.5 MPa, is achieved. The results of microstructure show that the wettability of the filler metal on Ti（C,N）-based cermet and steel is well. A mutual solution layer and a diffusion layer exist between the welding base materials and the filler metal.

ANALYSIS OF SHEAR STRESS DISTRIBUTION IN HONEYCOMB AIRCRAFT WING STRUCTURE SUBJECTED TO (S.T.) TORQUE

Using the method of elasticity, an analytical approach is developed to analyze the shear stress in a honeycomb wing structure with a large aspect ratio under the condition of free torsion. The formulas of shear stress, warping and angle of twist are derived. These formulas are both useful and convenient from the point of view in the structure design.

AN EXPERIMENTAL STUDY ON TURBULENT COHERENT STRUCTURES NEAR A SHEARED AIR-WATER INTERFACE

The turbulence structures near a sheared air-water interface were experimentally investigated with the hydrogen bubble visualization technique. Surface shear was imposed by an airflow over the water flow which was kept free from surface waves. Results show that the wind shear has the main influence on coherent structures under air-water interfaces. Low- and high- speed streaks form in the region close to the interface as a result of the imposed shear stress. When a certain airflow velocity is reached, “turbulent spots” appear randomly at low-speed streaks with some characteristics of hairpin vortices. At even higher shear rates, the flow near the interface is dominated primarily by intermittent bursting events. The coherent structures observed near sheared air-water interfaces show qualitative similarities with those occurring in near-wall turbulence. However, a few distinctive phenomena were also observed, including the fluctuating thickness of the instantaneous boundary layer and vertical vortices in bursting processes, which appear to be associated with the characteristics of air-water interfaces.

Analysis of the Ore-Controlling Structure of Ductile Shear Zone Type Gold Deposit in Southern Beishan Area, Gansu, Northwest China

The ductile shear zone-type gold deposit is a kind that both the ore-forming mechanism and ore-controlling factors are closely related to the ductile shear zone and its evolution. Ductile shear zone develops in Beishan area, Gansu of Northwest China, and develops especially well in the south belt. The controls of the ductile shear zone on gold deposits are as follows. （1） The regional distribution of gold deposits （and gold spots） is controlled by the ductile shear zone. （2） The ductile-brittle shear zone is formed in the evolution process of ductile shear zone and both are only ore-bearing structures and control the shape, attitude, scale, and distribution of mineralization zones and ore-bodies. （3） Compresso-shear ductile deformation results in that the main kind of gold mineralization is altered mylonite type and the main alteralization is metasomatic. （4） Ore-bearing fracture systems are mainly P-type ones, some D-type and R-type ones, but only individual R＇-type and T-type ones. （5） Dynamic differen- tiation and dynamic metamorphic hydrothermal solution resulting from ductile deformation is one of the sources of ore-forming fluid of gold mineralization, and this is identical with that ore-forming materials are mainly from metamorphic rocks, and ore-forming fluid is mainly composed of metamorphic water, and with the fluid inclusion and geo-chemical characteristics of the deposit. （6） There is a negative correlation between the gold abundance and susceptibility anlsotropy （P） of the altered mylonlte samples from the deposit, which shows that the gold mineralization is slightly later than the structural deformation. All above further expound the ore-forming model of the ductile shear zone type of gold deposits.

Transient response of doubly-curved bio-inspired composite shells resting on viscoelastic foundation subject to blast load using improved first-order shear theory and isogeometric approach

Investigating natural-inspired applications is a perennially appealing subject for scientists. The current increase in the speed of natural-origin structure growth may be linked to their superior mechanical properties and environmental resilience. Biological composite structures with helicoidal schemes and designs have remarkable capacities to absorb impact energy and withstand damage. However, there is a dearth of extensive study on the influence of fiber redirection and reorientation inside the matrix of a helicoid structure on its mechanical performance and reactivity. The present study aimed to explore the static and transient responses of a bio-inspired helicoid laminated composite(B-iHLC) shell under the influence of an explosive load using an isomorphic method. The structural integrity of the shell is maintained by a viscoelastic basis known as the Pasternak foundation, which encompasses two coefficients of stiffness and one coefficient of damping. The equilibrium equations governing shell dynamics are obtained by using Hamilton's principle and including the modified first-order shear theory,therefore obviating the need to employ a shear correction factor. The paper's model and approach are validated by doing numerical comparisons with respected publications. The findings of this study may be used in the construction of military and civilian infrastructure in situations when the structure is subjected to severe stresses that might potentially result in catastrophic collapse. The findings of this paper serve as the foundation for several other issues, including geometric optimization and the dynamic response of similar mechanical structures.

Prediction of Compressive and Shear Moduli of X-cor Sandwich Structures for Aeronautic Engineering

The so-called″X-cor sandwich structure″is a highly promising novel material as an alternative to honeycomb used in aircraft.Although much work has been conducted on the performance of the X-cor sandwich structure,the gap is still hardly bridged between experimental results and theoretical analyses.Therefore,a method has been innovated to establish semi-empirical formula for the prediction of compressive and shear moduli of X-cor sandwich structure composites,by combining theoretical analyses and experimental data.In addition,aprediction software was first developed based on the proposed method,of which the accuracy was verified through confirmatory experiments.This software can offer a direct reference or guide for engineers in structural designing.

Influence of Wind Turbine Structural Parameters on Wind Shear and Tower Shadow Effect

To overcome the problems of natural decreases in power quality,and to eliminate wind speed fluctuation due to wind shear and tower shadow effect arising from wind turbine structural parameters,an improved prediction model accounting for the dual effect of wind shear and tower shadow is,in this paper,built.Compared to the conventional prediction model,the proposed model contains a new constraint condition,which makes the disturbance term caused by the tower shadow effect always negative so that the prediction result is closer to the actual situation.Furthermore,wind turbine structural parameters such as hub height,rotor diameter,the diameter of the tower top,and rotor overhang on wind shear and tower shadow effect are also explored in detail.The results show that the wind shear effect became weaker with the increase in hub height.The hub height is independent of the tower shadow effect.The rotor diameter is positively correlated with the wind shear and tower shadow effect.The tower shadow effect is positively correlated with the diameter of the tower top and negatively correlated with the rotor overhang.

Short beam shear properties and failure modes of the wood-based X-type lattice sandwich structure

A wood-based X-type lattice sandwich structure was manufactured by insertion-glue method.The birch was used as core,and Oriented Strand Board was used as panel of the sandwich structure.The short beam shear properties and the failure modes of the wood-based X-type lattice sandwich structure with different core direction(vertical and parallel),unit specification(120 mm×60 mm and 60 mm×60 mm),core size(50 mm and 60 mm),and drilling depth(9 mm and 12 mm)were investigated by a short beam shear test and the establishment of a theoretical model to study the equivalent shear modulus and deflection response of the X-type lattice sandwich structure.Results from the short beam shear test and the theoretical model showed that the failure modes of the wood-based X-type lattice sandwich structure were mainly the wrinkling and crushing of the panels under three-point bending load.The experimental values of deflection response of various type specimens were higher than the theoretical values of them.For the core direction of parallel,the smaller the unit specification is,the shorter the core size is,and the deeper the drilling depth is,the greater the short beam shear properties of the wood-based X-type lattice sandwich structure is.

Shear wave velocity model using HVSR inversion beneath Bandar Lampung City

The horizontal-to-vertical spectral ratio(HVSR)method has been used to characterize site-effect parameters that are indispensable in seismic hazard and risk-reduction studies in urban areas and rapid land-use planning.This method is widely used because it is the cheapest and simplest geophysical method for the acquisition and processing stages.In subsequent developments,the HVSR method has been widely used to determine elastic rock parameters,particularly shear wave velocity(v_(S)),through the HVSR curve inversion process.Furthermore,the v_(S)structural model can be used to delineate the presence of complex geological structures,particularly faults and sedimentary basins.Bandar Lampung is a city in Lampung Province with many fault structures and groundwater basins to the south.There are 83 HVSR measurement points around Bandar Lampung for delineating the presence of fault structures and groundwater basins.We produced the HVSR curve from the measurement results and then performed an inversion process using the particle swarm optimization algorithm to obtain v_(S)for the depth profile.Subsequently,from this profile,we produced a two-dimensional(2D)lateral and vertical model.The mean v_(S)value was calculated from all the measurement points,and we found stiff soil layers reaching depths of approximately 5 m,with a value of v_(S)<330 m/s.A bedrock layer with a velocity exceeding 1250 m/s was visible at a depth of 100 m.Based on the 2D model,the v_(S)structure shows that the city of Bandar Lampung is divided into two zones,with a NW-SE boundary.The north-middle-eastern part of the city consists of harder rocks.This harder rock is characterized by extremely high v_(S)values,starting from a depth of 50 m.In contrast,the south-middle-west exhibits a low-moderate v_(S)anomaly associated with groundwater basins SW of the city.From the 2D v_(S)structural model,fault structures can be found along the city,characterized by a contrast of v_(S)values from low to medium and from medium to high.

A New Modified Conductivity Model for Prediction of Shear Yield Stress of Electrorheological Fluids Based on Face-center Square Structure

A new modified conductivity model was established to predict the shear yield stress of electrorheological fluids (ERF). By using a cell equivalent method, the present model can deal with the face-center square structure of ERF. Combining the scheme of the classical conductivity model for the single-chain structure, a new formula for the prediction of the shear yield stress of ERF was set up. The influences of the separation distance of the particles, the volume fraction of the particles and the applied electric field on the shear yield stress were investigated.

THE CHARACTERISTICS AND MODELLING EXPERIMENTS ON THE DEPOSIT-CONTROLLING STRUCTURE OF SHEAR-ZONE GOLD DEPOSIT IN CHINA

THE CHARACTERISTICS ANDMODELLING EXPERIMENTS ON THEDEPOSIT-CONTROLLING STRUCTUREOF SHEAR-ZONE GOLD DEPOSITIN CHINAWu Xueyi(Institute of Geochemistry, Academia Sinica, Guiyang, 550002, China)shear zone, gold-controlled structure, modelling experimentThe shear-zone gold deposits found in China can be divided into four types: (1) gold deposits controlled by the ductile shear-zones; (2) gold deposits controlled by the brittle-ductile shear zones; (3) gold deposits conntrolled by the ductile-brittle shear zones; (4) gold deposits controlled by the brittle shear zones. These gold deposits mostly occurred in the regions with higher abundance of gold, which underwent a long and complicated evolution-ary process and had obvious zoning and multiperiod metallogenic feature. The modelling exper-imental result of gold-controlled structure shows that the thermodynamics of compresso-shear structures made gold mobilizing and migrating in the earlier stage of shear zone; and that the extension process did

Study on the Structure of a Horizontal Shear Line over the Tibetan Plateau Based on CRA-Interim Datasets and Its Comparison with ERA-Interim Datasets

The CRA-Interim trial production of the global atmospheric reanalysis for 10 years from 2007 to 2016 was carried out by the China Meteorological Administration in 2017. The structural characteristics of the horizontal shear line over the Tibetan Plateau (TPHSL) based on the CRA-Interim datasets are examined by objectively identifying the shear line, and are compared with the analysis results of the European Centre for Medium-Range Weather Forecasts reanalysis data (ERA-Interim). The case occurred at 18UTC on July 5, 2016. The results show that both of the ERA-Interim and CRA-Interim datasets can well reveal the circulation background and the dynamic and thermal structure characteristics of TPHSL, and they have shown some similar features. The middle and high latitudes at 500 hPa are characterized by the circulation situation of"two troughs and two ridges", and at 200 hPa, the TPHSL is located in the northeast quadrant of the South Asian High Pressure (SAHP). The TPHSL locates in the positive vorticity zone and passes through the positive vorticity center corresponding to the ascending motion. Near the TPHSL, the contours of pseudo-equivalent potential temperature (θse) tend to be intensive, with a high-value center on the south side of the TPHSL. The TPHSL can extend to460 hPa and vertically inclines northward. There is a positive vorticity zone near the TPHSL which is also characterized by the northward inclination with the height, the ascending motion near the TPHSL can extend to 300 hPa, and the atmospheric layer above the TPHSL is stable. However, the intensities of the TPHSL’s structure characteristics analyzed with the two datasets are different, revealing the relatively strong intensity of geopotential height field, vertical velocity field, vorticity field and divergence field from the CRA-Interim datasets. In addition, the vertical profiles of the dynamic and water vapor thermal physical quantities of the two datasets are also consistent in the east and west part of the TPHSL. In summary, the reliable and usable CRA-Interim datasets show excellent properties in the analysis on the structural characteristics of a horizontal shear line over the Tibetan Plateau.

THE EFFECTS OF VELOCITY RATIO ON THE LARGE SCALE COHERENT STRUCTURES IN FREE SHEAR LAYERS

The velocity ratio of a free shear layer has an important influence on the spatial development of the large scale coherent structures in the layer. In this study, numerical simulations are performed to get an insight into this problem. The obtained numerical results agree quite well with those of a linear inviscid stability theory and the available experimental data.

Effect of Molecular Weight and Molecular Distribution on Skin Structure and Shear Strength Distribution near the Surface of Thin-Wall Injection Molded Polypropylene

In this study, the relationship between skin structure and shear strength distribution of thin-wall injection molded polypropylene (PP) molded at different molecular weight and molecular distribution was investigated. Skin-core structure, cross-sectional morphology, crystallinity, crystal orientation, crystal morphology and molecular orientation were evaluated by using polarized optical microscope, differential scanning calorimeter, X-ray spectroscopic analyzer and laser Raman spectroscopy, respectively, while the shear strength distribution was investigated using a micro cutting method called SAICAS (Surface And Interfacial Cutting Analysis System). The results indicated that the difference of molecular weight and molecular weight distribution showed own skin layer thickness. Especially, high molecular weight sample showed thicker layer of the lamellar orientation and molecular orientation than low molecular weight sample. In addition, wide molecular distribution sample showed large crystal orientation layer.