Indirect Vector Control of Linear Induction Motors Using Space Vector Pulse Width Modulation

Vector control schemes have recently been used to drive linear induction motors(LIM)in high-performance applications.This trend promotes the development of precise and efficient control schemes for individual motors.This research aims to present a novel framework for speed and thrust force control of LIM using space vector pulse width modulation(SVPWM)inverters.The framework under consideration is developed in four stages.To begin,MATLAB Simulink was used to develop a detailed mathematical and electromechanical dynamicmodel.The research presents a modified SVPWM inverter control scheme.By tuning the proportional-integral(PI)controller with a transfer function,optimized values for the PI controller are derived.All the subsystems mentioned above are integrated to create a robust simulation of the LIM’s precise speed and thrust force control scheme.The reference speed values were chosen to evaluate the performance of the respective system,and the developed system’s response was verified using various data sets.For the low-speed range,a reference value of 10m/s is used,while a reference value of 100 m/s is used for the high-speed range.The speed output response indicates that themotor reached reference speed in amatter of seconds,as the delay time is between 8 and 10 s.The maximum amplitude of thrust achieved is less than 400N,demonstrating the controller’s capability to control a high-speed LIM with minimal thrust ripple.Due to the controlled speed range,the developed system is highly recommended for low-speed and high-speed and heavy-duty traction applications.

A Pulse Width Modulation Scheme With Zero-sequence Voltage Injection for Single Phase Three-level NPC Rectifiers

直流侧中点电位电压偏移是多电平中性点钳位型变流器的主要缺点。以单相三电平NPC整流器为研究对象，以实现直流侧中点电位无漂移为控制目标，以传统的单相三电平单极性载波脉宽调制方法为基础，首先提出一种基于零序电压分量注入的载波脉宽调制算法；然后在此基础上给出基于零序电压分量极限值注入的载波脉宽调制算法；并给出这2种方法的零序电压分量的设计方案；最后，对这2种方法进行了详细的理论分析、计算机仿真和1kW样机实验对比验证。研究结果表明：所提出的2种算法都能有效实现直流侧中点电位平衡控制，其中基于零序电压分量极限值注入的载波调制算法的中点电位控制具有更快动态响应速度，且其网侧电流的高次谐波主要分布在开关频率附近；而基于零序电压分量注入的载波调制算法的网侧电流高次谐波主要分布在2倍开关频率附近。但是在一个调制信号周期内，基于零序电压分量极限值注入的载波调制算法的开关切换次数比基于零序电压分量注入的载波调制算法低25％左右。

Comparison of performance between bipolar and unipolar double-frequency sinusoidal pulse width modulation in a digitally controlled H-bridge inverter system

By deriving the discrete-time models of a digitally controlled H-bridge inverter system modulated by bipolar sinu- soidal pulse width modulation （BSPWM） and unipolar double-frequency sinusoidal pulse width modulation （UDFSPWM） respectively, the performances of the two modulation strategies are analyzed in detail. The circuit parameters, used in this paper, are fixed. When the systems, modulated by BSPWM and UDFSPWM, have the same switching frequency, the stabil- ity boundaries of the two systems are the same. However, when the equivalent switching frequencies of the two systems are the same, the BSPWM modulated system is more stable than the UDFSPWM modulated system. In addition, a convenient method of establishing the discrete-time model of piecewise smooth system is presented. Finally, the analytical results are confirmed by circuit simulations and experimental measurements.

Realization of Space Vector Pulse Width Modulation Method Based on DSP

In order to compensate for the deficiency of Sine Pulse Width Modulation（SPWM）, on the base of analyzing the principle of space w tot pulse width modulation and being compared with SPWM, the method of solving working time of adjacent vector and the method of generate space voltage vector were introduced. The experiment to the inverter which consists of IGBT proves that SVPWM centrol algorithm can reduce harmonic effectively, it is beneficial to enhancing the utilization rate of voltage source inverter direct current power supply.

Research and Making of a High-Power Switching Supply Using Pulse Width Modulation

Compared with the traditional SCR phase-shift regulated power supply, a new type of power semiconductor , noncrystalline state magnetic material and pulse width modulation technology, high-power switching supply has many advantages： small volume, high converting efficiency, good dynamic performance, small harmonic componont and small pollution to AC supply.

Digital Pulse Width Modulation Control in Power Electronic Circuits Design

The paper mainly focuses on the digital pulse width modulation (DPWM) control techniques for high performance power electronic circuit design. The problem to be solved in this study addresses the DPWM converter design for DC to DC conversion process. The control techniques have been utilized the Fuzzy Logic Rules Base method for proposed SIMULINK model of high performance power electronic circuit. The analytical calculations for real circuit design have been completed based on the mathematical modeling of the system. The results from the developed SIMULINK model confirm the target specifications of the high performance condition for power electronic circuit which was met the objective of this study. The numerical results have been carried out with the help of MATLAB/SIMULINK.

Improved Protein Transfer Efficiency and Signal Intensity in BlotMan Using Pulse Width Modulation

BlotMan is a protein blotting device that allows generating multiple membranes from a single polyacrylamide gel. To transfer all proteins uniformly with the same efficiency regardless of protein size, BlotMan employs pulse-width-modulated (PWM) voltage that applies a higher average voltage to a larger protein species. BlotMan can be controlled not only by its custom-made interface but also by a smart phone via Bluetooth technology. In this study, we examined effects of PWM signals (50%, 60%, and 80% duty cycle) on transfer efficiency and signal intensity in comparison to a constant voltage signal (100% duty cycle). The result revealed that in response to the same average voltage of 150 V, a lower duty cycle with a higher maximum voltage increased transfer efficiency as well as sharpness of transferred proteins. We validated BlotMan’s capability using a chondrosarcoma cell line (SW1353 cells) and a breast cancer cell line (MDA-MB231 cells) in response to antitumor chemical agents. BlotMan successfully generated 5 membranes from a single gel and detected 5 protein species such as c-Src, eukaryotic translation initiation factor 2 alpha (eIF2), phosphorylated eIF2, lamin B, and actin. Collectively, we demonstrated herein that BlotMan reduces an amount of protein samples by generating multiple membranes from a single gel and improving signal intensity with PWM voltage signals.

Capacitor Pattern H-Bridge Multilevel Inverter (CPHMLI) Using Phase Diposition Pulse Width Modulation for Grid Applications

This work presents an implementation of an innovative single phase multilevel inverter using capacitors with reduced switches. The proposed Capacitor pattern H-bridge Multilevel Inverter (CPHMLI) topology consists of a proper number of Capacitor connected with switches and power sources. The advanced switching control supplied by Pulse Width Modulation (PDPWM) to attain mixed staircase switching state. The charging and discharging mode are achieved by calculating the voltage error at the load. Furthermore, to accomplish the higher voltage levels at the output with less number of semiconductors switches and simple commutation designed using CPHMLI topology. To prove the performance and effectiveness of the proposed approach, a set of experiments performed under various load conditions using MATLAB tool.

Spectral Calculation of the Output Voltage of an Inverter with Bipolar Pulse Width Modulation

Converters with pulse width modulation are used for connections between the direct current （DC） and alternating current （AC） networks, e.g., in uninterrupted power supply systems, AC electromotor drives, for powering induction furnaces, in audio technique. Spectrum of signals sampled by pulse amplitude modulation and output voltage spectrum of the converter with pulse width modulation have similar properties. Spectrum of signals sampled by pulse amplitude modulation contains a harmonic of frequency equal to the frequency of the modulating signal and the harmonics of frequencies equal to the sum of frequency of the modulating signal and multiples of the sampling frequency. The output voltage spectrum of the converter with bipolar pulse width modulation contains harmonic of frequency equal to the frequency of the modulating signal and harmonics of frequencies equal to sum of the frequency of the modulating signal and multiples of the frequency of the carrier signal. It also contains harmonics of frequencies equal to the sum of the multiples of the frequency of the modulating signal and the multiples of the carrier signal. The comparison analysis was carried out for the harmonics of the output voltage of the converter with bipolar pulse width modulation in time domain. The dependency of the amplitudes and frequency spectrum on the wave forms of the carrier signal and modulating signal was shown. Similarity of the output voltage spectrum of the converter and signal spectrum sampled by the pulse width modulation was also shown. Key words： Output voltage converter with bipolar pulse width modulation, spectral analysis, Fourier series, carrier signal, reference signal.

Temporal characteristic analysis of single event effects in pulse width modulator

In this paper,the nature and origin of single event effects(SEE) are studied by injecting laser pulses into different circuit blocks,combining with analysis to map pulse width modulators circuitry in the microchip die.A time-domain error-identification method is used in the temporal characteristic analysis of SEE.SEE signatures of different injection times are compared.More serious SEE are observed when the laser shot occurs on a rising edge of the device output for blocks of the error amplifier,current sense comparator,and T and SR latches.

An Improved Submodule Unified Pulse Modulation Scheme for a Hybrid Modular Multilevel Converter

This paper presents an improved submodule unified pulse width modulation(SUPWM)scheme for a hybrid modular multilevel converter(MMC)composed of half-bridge submodules(HBSMs)and full-bridge submodules(FBSMs).The proposed SUPWM scheme can achieve an output voltage of(2N+1)(where N is the number of submodules in each arm)levels,which is the same as that of the carrier-phase-shifted PWM(CPSPWM)scheme.Meanwhile,the proposed SUPWM scheme can alleviate the uneven loss distributions between the left leg and right leg in FBSMs of the hybrid MMC.Moreover,the capacitor voltages of the sub-modules can be well balanced without complicated closed-loop voltage balancing controllers.The validity of the proposed SUPWM scheme is verified by both the simulated and experimental results.

Evaluation of a Pulse Width Modulated Bypass Nozzle for the Development of a Variable Load Residential Oil Burner

Due to the need for energy conservation in buildings and the simultaneous benefit of cost savings, the development of a low firing rate load modulating residential oil burner is very desirable. One of the two main requirements of such a burner is the development of a burner nozzle that is able to maintain the particle size distribution of the fuel spray in the desirable (small) size range for efficient and stable combustion. The other being the ability to vary the air flow rate and air distribution around the fuel nozzle in the burner for optimal combustion at the current fuel firing rate. In this paper, which deals with the first requirement, we show that by using pulse width modulation in the bypass channel of a commercial off-the-shelf bypass nozzle, this objective can be met. Here we present results of spray patterns and particle size distribution for a range of fuel firing rates. The results show that a desirable fuel spray pattern can be maintained over a fuel firing rate turndown ratio (Maximum Fuel Flow Rate/Minimum Fuel Flow Rate) of 3.7. Thus here we successfully demonstrate the ability to electronically vary the fuel firing rate by more than a factor of 3 while simultaneously maintaining good atomization.

A Kind of PWM Pneumatic Servo Control System——Modulation Methods and Dynamic Responses

Vibrations or dither's are features of the PWM servo control system in their steady outputs. On the grounds of analyses and experiments of a PWM pneumatic servo control system, the paper puts forward four varieties of PWM modulation methods, and concludes on the relationship between dithers and the different methods, and then discusses the influence of friction to the dithers. Results from experiments regarding the dynamic and static responses on the given system support the theories presented.

Research of the Unity Theory Between Three-level Space Vector and Carrier-based PWM Modulation Strategy

两电平空间矢量脉宽调制（space vector pulse widthmodulation,SVPWM）与正弦脉宽调制（sinusoidal pulse widthmodulation,SPWM）存有一定的本质关系,对于三电平,在常见的8段式SVPWM序列中可以证明,SVPWM与SPWM本质上也存在某种统一。实际的SVPWM调制中,由于要考虑中点电压平衡、减少谐波等其它性能问题,一般会利用开关冗余状态得到8段以上的开关调制序列。目前的文献中还未曾有对这些情况进行统一性地验证,因此三电平SVPWM与SPWM的统一理论存在一定的不足。研究发现,可通过严格地理论推导将传统意义上的调制波分解为2个子调制波,再进行SPWM调制,可以得到与SVPWM完全吻合的序列。该文在此方法基础上深入研究了8段以上（10、12、14段）的SVPWM调制序列与SPWM的统一。经过严格地理论推导,成功实现了含任意段数的SVPWM序列与SPWM的统一。仿真结果证明了该理论的正确性。

A NEW MODULATION SCHEME FOR IR-UWB COMMUNICATION SYSTEMS

Since the poor performance of orthogonal binary Pulse Position Modulation (PPM) compared with binary Pulse Amplitude Modulation (PAM), this paper presents a new modulation scheme named Pulse Width Modulation (PWM) for Impulse Radio Ultra-WideBand (IR-UWB) communication systems. This modulation scheme uses pulses with equal amplitude and different widths to carry different information. The receiver employs differences between similarity coefficients among these pulses to distinguish different information. Both theoretical analysis and simulation results verify that this novel scheme has a Signal to Noise Ratio (SNR) gain of about 1.75 dB compared with or- thogonal binary PPM, and has an SNR loss of about 1.4 dB compared with binary PAM. Although both the theoretical analysis and simulations are based on time-hopping multiple access, this modulation scheme can also be applied to other accessing techniques of UWB communication systems.

Application of chaotic modulation to AC motors for electro magnetic interference suppression

Instead of avoiding occurrence of chaos in motor drives, chaos is positively utilized in this paper. A new chaotic pulse width modulation （PWM） scheme is proposed and implemented for AC motors, which functions to significantly suppress harmonic peaks and hence acoustic noise. The key is to employ the Chua＇s circuit for generating a desired chaotic sequence. By using a practical induction motor, computer simulation and experimental results verify that the chaotic PWM has advantages of harmonic peak suppression and simple hardware implementation over the conventional PWM and random PWM.

Improved VSVPWM Modulation Method for Three-level NPC Inverter in Rural Power Grid

With the acceleration of agricultural electrification,a lot of nonlinear and shock loads appear in the rural power grid,and the resulting harmonic and reactive currents pollute the rural power grid more and more seriously.To solve the above problem,three-level neutral point clamped(NPC)inverters have been widely used,but their development is greatly restricted by the defect of neutral point voltage imbalance.In this paper,an improved virtual space vector pulse width modulation(VSVPWM)was proposed.Firstly,the mathematical models of various space vectors were established,and the influence of various space vectors on neutral point voltage was analyzed.The sum of the vector current at the neutral point was zero and the voltage control at the neutral point was completed by.introducing the time offset into different switching times of the redundant small vector.This method was simple in design and avoided the redundant calculation of the traditional VSVPWM method and tedious switch sequence design.This balancing control strategy could greatly reduce the influence of virtual vectors on neutral point voltage and effectively control the low-frequency oscillation of neutral point voltage.The validity of the method was verified by establishing a matlab simulation model.

基于虚拟电压矢量的双三相直线磁通切换永磁电机容错SVPWM策略

高可靠性是电梯驱动系统的首要指标。针对双三相直线磁通切换永磁(dual-three-phase linear flux switching permanent magnet,DTP-LFSPM)电机单相开路故障,提出一种基于虚拟电压矢量的容错空间矢量脉宽调制策略。首先,基于单相开路故障下的五维变换矩阵计算得到故障后的32个空间电压矢量分布。然后,筛选部分空间电压矢量,以z子空间电压幅值为零且每个扇区产生对称的脉宽调制波形为目标,重构得到12个虚拟电压矢量,相邻的2个虚拟电压矢量都由3个基本电压矢量组成,并用于合成参考电压矢量,不仅可以减少单相开路故障容错控制时的电流谐波,而且具有计算简单,易于硬件实现等优点。最后,搭建DTP-LFSPM电机驱动控制系统仿真与实验平台,仿真和实验测试结果证明所提容错策略的正确性和有效性。

T型三电平逆变器中点电位平衡电路及控制

直流母线电压中点电位不平衡是T型三电平逆变器的拓扑结构造成的固有问题。这里从T型三电平逆变器的拓扑结构出发,分析了空间矢量脉宽调制(SVPWM)中大、中和小矢量对中点电位不平衡的影响,针对中点电位不平衡,在电源侧并联一个半桥模块且中点与母线中点串联电感的平衡电路,然后对平衡电路被控对象进行建模与分析,推导出中点电压平衡控制框图,通过对上、下电容进行充放电控制,控制中点电位达到平衡,最后,搭建了T型三电平逆变器实验平台,进行了仿真和实验验证,实验结果验证了所提平衡电路和控制的有效性和可行性。