A model of deformation of thin-wall surface parts during milling machining process

A three-dimensional finite element model was established for the milling of thin-walled parts. The physical model of the milling of the part was established using the AdvantEdge FEM software as the platform. The aluminum alloy impeller was designated as the object to be processed and the boundary conditions which met the actual machining were set. Through the solution, the physical quantities such as the three-way cutting force, the tool temperature, and the tool stress were obtained, and the calculation of the elastic deformation of the thin-walled blade of the free-form surface at the contact points between the tool and the workpiece was realized. The elastic deformation law of the thin-walled blade was then predicted. The results show that the maximum deviation between the predicted value and the actual measured machining value of the elastic deformation was 26.055 μm; the minimum deviation was 2.011 μm, with the average deviation being 10.154 μm. This shows that the prediction is in close agreement with the actual result.

Development of Fixture Layout Optimization for Thin-Walled Parts:A Review

An increasing number of researchers have researched fixture layout optimization for thin-walled part assembly during the past decades.However,few papers systematically review these researches.By analyzing existing literature,this paper summarizes the process of fixture layout optimization and the methods applied.The process of optimization is made up of optimization objective setting,assembly variation/deformation modeling,and fixture layout optimization.This paper makes a review of the fixture layout for thin-walled parts according to these three steps.First,two different kinds of optimization objectives are introduced.Researchers usually consider in-plane variations or out-of-plane deformations when designing objectives.Then,modeling methods for assembly variation and deformation are divided into two categories:Mechanism-based and data-based methods.Several common methods are discussed respectively.After that,optimization algorithms are reviewed systematically.There are two kinds of optimization algorithms:Traditional nonlinear programming and heuristic algorithms.Finally,discussions on the current situation are provided.The research direction of fixture layout optimization in the future is discussed from three aspects:Objective setting,improving modeling accuracy and optimization algorithms.Also,a new research point for fixture layout optimization is discussed.This paper systematically reviews the research on fixture layout optimization for thin-walled parts,and provides a reference for future research in this field.

A Systematic Review of Computer Vision Techniques for Quality Control in End-of-Line Visual Inspection of Antenna Parts

The rapid evolution of wireless communication technologies has underscored the critical role of antennas in ensuring seamless connectivity.Antenna defects,ranging from manufacturing imperfections to environmental wear,pose significant challenges to the reliability and performance of communication systems.This review paper navigates the landscape of antenna defect detection,emphasizing the need for a nuanced understanding of various defect types and the associated challenges in visual detection.This review paper serves as a valuable resource for researchers,engineers,and practitioners engaged in the design and maintenance of communication systems.The insights presented here pave the way for enhanced reliability in antenna systems through targeted defect detection measures.In this study,a comprehensive literature analysis on computer vision algorithms that are employed in end-of-line visual inspection of antenna parts is presented.The PRISMA principles will be followed throughout the review,and its goals are to provide a summary of recent research,identify relevant computer vision techniques,and evaluate how effective these techniques are in discovering defects during inspections.It contains articles from scholarly journals as well as papers presented at conferences up until June 2023.This research utilized search phrases that were relevant,and papers were chosen based on whether or not they met certain inclusion and exclusion criteria.In this study,several different computer vision approaches,such as feature extraction and defect classification,are broken down and analyzed.Additionally,their applicability and performance are discussed.The review highlights the significance of utilizing a wide variety of datasets and measurement criteria.The findings of this study add to the existing body of knowledge and point researchers in the direction of promising new areas of investigation,such as real-time inspection systems and multispectral imaging.This review,on its whole,offers a complete study of computer vision approaches for quality control in antenna parts.It does so by providing helpful insights and drawing attention to areas that require additional exploration.

Comparison of wear behavior of ABS and Nylon6-Fe powder composite parts prepared with fused deposition modelling

Fused deposition modeling(FDM) is one of the latest rapid prototyping techniques in which parts can be manufactured at a fast pace and are manufactured with a high accuracy. This research work is carried out to study the friction and wear behavior of parts made of newly developed Nylon6-Fe composite material by FDM. This work also involves the comparison of the friction and wear characteristics of the Nylon6-Fe composite with the existing acrylonitrile butadiene styrene(ABS) filament of the FDM machine. This Is carried out on the pin on disk setup by varying the load(5, 10, 15 and 20 N) and speed(200 and 300 r/min). It is concluded that the newly developed composite is highly wear resistant and can be used in industrial applications where wear resistance is of paramount importance. Morphology of the surface in contact with the Nylon6-Fe composite and ABS is also carried out.

Multi-Material Topology Optimization of Structures Using an Ordered Ersatz Material Model

This paper proposes a new element-based multi-material topology optimization algorithm using a single variable for minimizing compliance subject to a mass constraint.A single variable based on the normalized elemental density is used to overcome the occurrence of meaningless design variables and save computational cost.Different from the traditional material penalization scheme,the algorithm is established on the ordered ersatz material model,which linearly interpolates Young’s modulus for relaxed design variables.To achieve a multi-material design,the multiple floating projection constraints are adopted to gradually push elemental design variables to multiple discrete values.For the convergent element-based solution,the multiple level-set functions are constructed to tentatively extract the smooth interface between two adjacent materials.Some 2D and 3D numerical examples are presented to demonstrate the effectiveness of the proposed algorithm and the possible advantage of the multi-material designs over the traditional solid-void designs.

Research on Three-Echelon Inventory Model and Algorithm for Valuable Spare Parts in Weapon Equipment

According to the current situation of repair and supply for valuable spare parts in the weapon equipment of the PLA,using the research results of the repairable spare parts inventory theory,an inventory model of the valuable spare parts in three-echelon repair and supply system is established by expanding the classical METRIC model and theory,and the genetic algorithm is utilized to solve the model.In the algorithm,the chromosome representation and initial population production,the crossover and mutation operators are designed.By using an example,a simulation analysis is carried out to verify the model's correctness.

MODELING AND CONTROL OF A UNIVERSAL PART FEEDER

The modeling and motion control of a universal part feeder is addressed. The feeder consists of a flat plate （or called bed） and a part placed on the plate. The bed can vibrate side-by-side （in x axis）, back and forth （in y axis）, clockwise and counter clockwise （about z axis）, actuated by three linear motors （voice coils）. When the bed does these vibrations, the part placed on the plat will have position and/or orientation change due to the interaction between the two contact surfaces. By controlling the ways in which the plate vibrates, the position and orientation of the part can be controlled. The two vibration profiles of the bed are investigated in the research： the high-low vibration mode and the bang-bang vibration mode. The motion equations of the bed and the part as well as the control schemes for the high-low vibration mode are presented. Both simulation and real-time testing verify the system＇s dynamic model and indicate the feasibilities of the developed control laws.

Feasibility of establishing model of Parkinson disease by injecting 6-hydroxydopamine at different parts of the nigrostriatal pathway in the brain of rats

BACKGROUND： Previous researches found that animal models with Parkinson disease （PD） could be established by injecting 6-hydroxydopamine （6-OHDA） into medial forebrain bundle （MFB）, substantia nigra compacta （SNC） and caudate-putamen complex （CPU） of the nigrostriatal pathway. OBJECTIVE ： To compare behavioral, biochemica 6-OHDA injections in the areas of MFB, SNC and DESIGN： Controlled observational study and histological properties of these rats undergoing the CPU respectively. SEI-IING： Department of Neurology, First Affiliated Hospital of Guangxi Medical University MATERIALS： A total of 64 adult female SD rats weighing 180-230 g were provided by the Animal Experimental Center of Guangxi Medical University. 6-OHDA （Sigma Company, USA）; Brain solid positioner （Standard model 51600, Stoelting Co., IL, USA）; rotational monitoring of little animal （type QL-1, USA）; high liquid chromatography （HLC, Waters Company）. METHOOS： The experiment was carried out in the Medical Experimental Center of Guangxi Medical University from February to December 2005. ① According to digital table, 64 SD rats were divided into MFB group, SNC group, CPU group and control group with 16 in each group. On the basis of the brain atlas of Paxinos, rats in the first three groups were injected with 5 μL 6-OHDA into right MFB （0 mm of line of incisor tooth, A/P 4.4 mm, L/R 1.2 mm, ON -7.8 mm）, SNC （line of incisor tooth just equal to horizon, A/P -4.8 mm, L/R 1.6 mm, ON -7.8 mm） and CPU （0 mm of line of incisor tooth, A/P 1.2 mm, L/R 2.7 mm, ON -5.4 mm）, respectively. The rats in control group were injected with 5 μL ascorbic acid solution （2 g/L）. One week after operation, 0.1 g/L apomorphine （Apo, 0.05 mg/kg） was subcutaneously injected into neck and then rotational behavior induced by Apo was recorded once a week for 8 weeks. The PD models were considered successful only when rotational times more than or equal to 7 times per minute. Eight weeks after operation, micro-perfusion was used to obtain micro-perfusate in bilateral CPU and contents of 3,4-dihydroxyphenylacetic acid （3,4-DOPAC） and homovanillic acid （HVA） were also measured. In addition, amount of tyrosine hydroxylase positive cells （TH＊） in SNC was counted with immuno- histochemical staining. MAIN OUTCOME MEASURES ： ① Successful rate of PD models; ② contents of dopamine and its metabolite in MFB, SNC and CPU groups and TH＊ amount. RESULTS： All 64 SD rats were involved in the final analysis. ③ Successful rate and rotational behavior： One week after operation, there were 6 successful models both in SNC and MFB groups; in the 2^nd week, there were 6 both in SNC and MFB groups and 1 in CPU group; in the 3^nd week, there were 1 in MFB group and 3 in CPU group; in the 4^nd week, there were 3 in CPU group. Otherwise, no successful case was found out in the next 3 weeks. Abnormal rotational behavior was not observed in control group. Four weeks after operation, successful rates were 81% （13/16） in MFB group, 75% （12/16） in SNC group and 44% （7/16） in CPU group.② Contents of 3, 4-DOPAC and HVA： Eight weeks after operation, contents in the SNC area of the injured side were lower than those on non-lesion side （P 〈 0.01）.③Changes of TH＋ amount： Eight weeks after operation, TH＋ amount in the SNC area of the lesion side was lower than that on non-lesion side （P 〈 0.01 ）. CONCLUSION： Injecting 6-OHDA into MFB, SNC and CPU can damage dopaminergic cells and establish successful PD models.

An Integrated Geometric Modeling Methodology for 2.5D Cylindrical Prismatic Part for Computer Aided Process Planning

The field of solid modeling has created numerous techniques for unambiguous computer representations of three-dimensional objects. Its data structures and algorithms have been used in a broad range of applications: Computer-Aided Design and Computer-Aided Manufacturing (CAD/ CAM), robotics, computer vision, computer graphics and visualization, virtual reality, etc. This research paper is used to generate process plan from feature-based modeling, based on an integrated geometric modeling system that supports both feature-based modeling and information storage. Present system is developed only for milling components and limited to selective machining features for prismatic components and further implemented for more machining features to develop algorithms for modeling the components through the input of machining features. As a result, feature information is directly available to downstream activities, and feature extraction is no longer needed. The various systematic steps involved in this approach are study of Design, identification of Features, selection of Processes, Tools and Machines, Machining and Inspection [DFPTMMI]. Machining features generated in the design stage are recognized and stored under the Visual Basic control of CATIA software ActiveX interface. Algorithms are developed for individual features and these algorithms are embedded in Visual Basic forms. This system is discussed and suited for 2.5 Dimensional part approach, however, that can be extended to 3 dimensional prismatic part and complex features machining. Finally a process planning chart has been presented as a model process planning.

A FEATURE－BASED PRODUCT MODELLING SYSTEM ON PC （CASE STUDY OF PARTS DESIGN FOR PRESS MACHINE）

This article reports on the design and implementation of feature modelling system for the CAPP of rotational symmetric components. The work deals with design by features, feature parts database design, and parts information modelling techniques realized in Personal Computer. The modular software provides utilities such as interactive component synthesis, dimensioning, tolerancing and graphical display.

Numerical simulation analysis for deformation deviation and experimental verification for an antenna thin-wall parts considering riveting assembly with finite element method

In the process of thin-wall parts assembly for an antenna,the parts assembly deformation deviation is occurring due to the riveting assembly.In view of the riveting assembly deformation problems,it can be analyzed through transient and static simulation.In this work,the theoretical deformation model for riveting assembly is established with round head rivet.The simulation analysis for riveting deformation is carried out with the riveting assembly piece including four rivets,which comparing with the measuring points experiment results of riveting test piece through dealing with the experimental data using the point coordinate transform method and the space line fitting method.Simultaneously,the deformation deviation of the overall thin-wall parts assembly structure is analyzed through finite element simulation;and its results are verified by the measuring experiment for riveting assembly with the deformation deviation of some key points on the thin-wall parts.Through the comparison analysis,it is shown that the simulation results agree well with the experimental results,which proves the correctness and effectiveness of the theoretical analysis,simulation results and the given experiment data processing method.Through the study on the riveting assembly for thin-wall parts,it will provide a theoretical foundation for improving thin-wall parts assembly quality of large antenna in future.

Fatigue Life Prediction of Shaft Parts

Taking high speed rotating shaft parts as the research object,the general fault mode of the parts is analyzed.The analysis process of shaft parts is expounded by means of finite element analysis method.A variety of fatigue life prediction methods for mechanical equipment parts are reviewed in this paper.And the selection and calculation method of parameters in the life prediction model of shaft parts are summarized.Finally,taking a gear shaft of a reducer as an example,the Morrow linear correction of the elastic stress model,Manson-Halford(M-H)correction model and Smith Watson Topper(SWT)correction model are applied to fatigue life assessments.The prediction results of the SWT correction model are relatively conservative.The prediction results of the Morrow linear correction of the elastic stress model and the M-H model are similar,and they are larger than the SWT correction model.

Welding thermal characteristics analysis with numerical simulation for thin-wall parts assembly under different conditions

In order to analyze the welding thermal characteristics problem,the multiscale finite element(FE)model of T-shape thin-wall assembly structure for different thicknesses and the heat source model are established to emphatically study their welding temperature distributions under different conditions.Simultaneously,different welding technology parameters and welding directions are taken into account,and the fillet weld for different welding parameters is employed on the thin-wall parts.Through comparison analysis,the results show that different welding directions,welding thicknesses and welding heat source parameters have a certain impact on the temperature distribution.Meanwhile,for the thin-wall assembly structure of the same thickness,when the heat source is moving,the greater the moving speed,the smaller the heating area,and the highest temperature will decrease.Therefore,the welding temperature field distribution can be altered by adjusting welding parameters,heat source parameters,welding thickness and welding direction,which is conducive to reducing welding deformation and choosing an appropriate and optimal welding thickness of thin-wall parts and relative welding process parameters,thus improving thin-wall welding structure assembly precision in the actual large-size welding structure assembly process in future.

SIMPLE ECOSYSTEM MODEL OF THE CENTRAL PART OF THE EAST CHINA SEA IN SPRING

This paper’s simple ecological model to simulate the ecosystem variation and the vertical carbon flux in the central part of the East China Sea in spring, inter-reated the phytoplankton, zooplankton,autotrophic and heterotrophic bacterioplankton, nitrate, and dissolved organic carbon (DOC) in a run lasting 90 days. Except for DOC, because of poor observation precision,the major seasonal features of the vertical distribution for these components can be simulated by this model. The results show that spring bloom is just a short period of 1-2 weeks and that deposit carbon flux at the bottom interface is about 200 mg /m2 ·d in the first 20 days and then reaches its maximum of 1500mg/m2·d about 2 months later after the spring bloom.

PHYSICAL MODELLING OF ISOTHERMAL DIE FORGING PROCESS OF Ti-ALLOY STRUCTURAL AIR-FRAME PART WITH ETYPE CROSS-SECTION AND VARYING THICKNESS RIB

Isothermal flashless die forging process of Ti - alloy structural air - frame part with varying thickness rib has been modelled in this paper.The results of present study show that a upside - down trapezoid rib would be formed and buckling would occure as blank is reduced,if the thickness of billet is maller than or equal to the thickness of rib. During modelling process of structural air frame part with E type cross - section rib, the saddle or lap would be formed finally at the middle of transverse rib between ribs with increase in deformation.If metal is allowed to flow out at confluence of longitudinal and transverse rib, the lop defect would be eliminated,, but a pipe cavity is obvious on corresponding loca- tion of blank. of defect formation depends on distance of metal flow ,friction,temperature homoge- neity of the blank and complexity of the part.

农户土地流转对其正规金融信贷可得性的影响——基于two-part model的实证分析

本文基于农户土地流转对其正规金融信贷可得性影响的理论分析,以陕西省关中地区442份实地调查数据为基础,构建两部分模型研究土地流入情况对农户正规金融信贷参与和金额的影响,得出如下结论:农户是否进行土地流入及土地流入面积对其所获得的信贷金额有显著的正向影响。农业技术培训对农户是否获得正规金融信贷具有显著的正向影响,家庭固定资产价值、社会资本和金融环境对其是否获得正规金融信贷和金额都具有显著的正向影响。最后提出相应的对策建议,以期为我国农村金融的发展提供借鉴。

An EPQ-Based Inventory Model for Deteriorating Items under Stock-Dependent Demand with Immediate Part Payment

In this paper, an EPQ-based inventory policy for an item is presented with stock-dependent demand during two trade credit periods. In addition, there is a provision for 1) an immediate part payment to the wholesaler, 2) borrowing some money from money lending source for the immediate part payment, 3) here supplier or wholesaler offers a trade credit period to his retailer and retailer also offers a trade credit period to his customer. Against the above conjectures inventory model has been formulated with respect to the retailer’s point of view for minimizing the total inventory cost. The non-linear optimization method-Generalized Reduced Gradient (GRG) method is used to find the optimal solutions. Lastly Numerical examples are set to illustrate this model. Finally we use LINGO software to solve this model.

基于tree part-based模型的目标识别和定位

提出了一种基于tree part-based模型的目标识别和定位的方法。该方法将tree part-based模型应用于静态图像中单一目标的识别定位,使用可变形模板(Deformable template)处理测试图像,提取与训练模型中的每一部分关联度在一定阈值范围内的特征点,结合外观模型和空间模型实现目标识别和定位。实验结果表明,该方法提高了目标识别和定位的准确率和可靠性。

A Survey on Deep Learning-Based 2D Human Pose Estimation Models

In this article,a comprehensive survey of deep learning-based(DLbased)human pose estimation(HPE)that can help researchers in the domain of computer vision is presented.HPE is among the fastest-growing research domains of computer vision and is used in solving several problems for human endeavours.After the detailed introduction,three different human body modes followed by the main stages of HPE and two pipelines of twodimensional(2D)HPE are presented.The details of the four components of HPE are also presented.The keypoints output format of two popular 2D HPE datasets and the most cited DL-based HPE articles from the year of breakthrough are both shown in tabular form.This study intends to highlight the limitations of published reviews and surveys respecting presenting a systematic review of the current DL-based solution to the 2D HPE model.Furthermore,a detailed and meaningful survey that will guide new and existing researchers on DL-based 2D HPE models is achieved.Finally,some future research directions in the field of HPE,such as limited data on disabled persons and multi-training DL-based models,are revealed to encourage researchers and promote the growth of HPE research.