Optimization Control of Multi-Mode Coupling All-Wheel Drive System for Hybrid Vehicle

The all-wheel drive(AWD)hybrid system is a research focus on high-performance new energy vehicles that can meet the demands of dynamic performance and passing ability.Simultaneous optimization of the power and economy of hybrid vehicles becomes an issue.A unique multi-mode coupling(MMC)AWD hybrid system is presented to realize the distributed and centralized driving of the front and rear axles to achieve vectored distribution and full utilization of the system power between the axles of vehicles.Based on the parameters of the benchmarking model of a hybrid vehicle,the best model-predictive control-based energy management strategy is proposed.First,the drive system model was built after the analysis of the MMC-AWD’s drive modes.Next,three fundamental strategies were established to address power distribution adjustment and battery SOC maintenance when the SOC changed,which was followed by the design of a road driving force observer.Then,the energy consumption rate in the average time domain was processed before designing the minimum fuel consumption controller based on the equivalent fuel consumption coefficient.Finally,the advantage of the MMC-AWD was confirmed by comparison with the dynamic performance and economy of the BYD Song PLUS DMI-AWD.The findings indicate that,in comparison to the comparative hybrid system at road adhesion coefficients of 0.8 and 0.6,the MMC-AWD’s capacity to accelerate increases by 5.26%and 7.92%,respectively.When the road adhesion coefficient is 0.8,0.6,and 0.4,the maximum climbing ability increases by 14.22%,12.88%,and 4.55%,respectively.As a result,the dynamic performance is greatly enhanced,and the fuel savings rate per 100 km of mileage reaches 12.06%,which is also very economical.The proposed control strategies for the new hybrid AWD vehicle can optimize the power and economy simultaneously.

Fake News Detection Based on Text-Modal Dominance and Fusing Multiple Multi-Model Clues

In recent years,how to efficiently and accurately identify multi-model fake news has become more challenging.First,multi-model data provides more evidence but not all are equally important.Secondly,social structure information has proven to be effective in fake news detection and how to combine it while reducing the noise information is critical.Unfortunately,existing approaches fail to handle these problems.This paper proposes a multi-model fake news detection framework based on Tex-modal Dominance and fusing Multiple Multi-model Cues(TD-MMC),which utilizes three valuable multi-model clues:text-model importance,text-image complementary,and text-image inconsistency.TD-MMC is dominated by textural content and assisted by image information while using social network information to enhance text representation.To reduce the irrelevant social structure’s information interference,we use a unidirectional cross-modal attention mechanism to selectively learn the social structure’s features.A cross-modal attention mechanism is adopted to obtain text-image cross-modal features while retaining textual features to reduce the loss of important information.In addition,TD-MMC employs a new multi-model loss to improve the model’s generalization ability.Extensive experiments have been conducted on two public real-world English and Chinese datasets,and the results show that our proposed model outperforms the state-of-the-art methods on classification evaluation metrics.

Two Monte Carlo-based simulators for imaging-system modeling and projection simulation of flat-panel X-ray source

The advantages of a flat-panel X-ray source(FPXS)make it a promising candidate for imaging applications.Accurate imaging-system modeling and projection simulation are critical for analyzing imaging performance and resolving overlapping projection issues in FPXS.The conventional analytical ray-tracing approach is limited by the number of patterns and is not applicable to FPXS-projection calculations.However,the computation time of Monte Carlo(MC)simulation is independent of the size of the patterned arrays in FPXS.This study proposes two high-efficiency MC projection simulators for FPXS:a graphics processing unit(GPU)-based phase-space sampling MC(gPSMC)simulator and GPU-based fluence sampling MC(gFSMC)simulator.The two simulators comprise three components:imaging-system modeling,photon initialization,and physical-interaction simulations in the phantom.Imaging-system modeling was performed by modeling the FPXS,imaging geometry,and detector.The gPSMC simulator samples the initial photons from the phase space,whereas the gFSMC simulator performs photon initialization from the calculated energy spectrum and fluence map.The entire process of photon interaction with the geometry and arrival at the detector was simulated in parallel using multiple GPU kernels,and projections based on the two simulators were calculated.The accuracies of the two simulators were evaluated by comparing them with the conventional analytical ray-tracing approach and acquired projections,and the efficiencies were evaluated by comparing the computation time.The results of simulated and realistic experiments illustrate the accuracy and efficiency of the proposed gPSMC and gFSMC simulators in the projection calculation of various phantoms.

Application of Patient Simulators Combined with Internet plus Scenario Simulation Teaching Models on Intravenous Infusion Nursing Education in China

Objective: To explore the effectiveness of applying patient simulators combined with Internet Plus scenario simulation teaching models on intravenous (IV) infusion nursing education, and to provide scientific evidence for the implementation of advanced teaching models in future nursing education. Methods: Enrolled 60 nurses who took the IV infusion therapy training program in our hospital from January 2022 to December 2023 for research. 30 nurses who were trained in traditional teaching models from January to December 2022 were selected as the control group, and 30 nurses who were trained with simulation-based teaching models with methods including simulated patients, internet, online meetings which can be replayed and scenario simulation, etc. from January to December 2023 were selected as the experimental group. Evaluated the learning outcomes based on the Competency Inventory for Nursing Students (CINS), Problem-Solving Inventory (PSI), comprehensive learning ability, scientific research ability, and proficiency in the theoretical knowledge and practical skills of IV infusion therapy. Nursing quality, the incidence of IV infusion therapy complications and nurse satisfaction with different teaching models were also measured. Results: The scientific research ability, PSI scores, CINS scores, and comprehensive learning ability of the experimental group were better than those of the control group (P 0.05), and their assessment results of practical skills, nursing quality of IV infusion therapy during training, and satisfaction with teaching models were all better than those of the control group with statistical significance (P < 0.05). The incidence of IV infusion therapy complications in the experimental group was lower than that in the control group, indicating statistical significance (P < 0.05). Conclusions: Teaching models based on patient simulators combined with Internet Plus scenario simulation enable nursing students to learn more directly and practice at any time and in any place, and can improve their proficiency in IV infusion theoretical knowledge and skills (e.g. PICC catheterization), core competencies, problem-solving ability, comprehensive learning ability, scientific research ability and the ability to deal with complicated cases. Also, it helps provide high-quality nursing education, improve the nursing quality of IV therapy, reduce the incidence of related complications, and ensure the safety of patients with IV therapy.

Transurethral resection of bladder tumor: A systematic review of simulator-based training courses and curricula

Objective:Transurethral resection of bladder tumor is one of the most common everyday urological procedures.This kind of surgery demands a set of skills that need training and experience.In this review,we aimed to investigate the current literature to find out if simulators,phantoms,and other training models could be used as a tool for teaching urologists.Methods:A systematic review was performed according to the Preferred Reporting Items for Systematic reviews and Meta-Analyses statement and the recommendations of the European Association of Urology guidelines for conducting systematic reviews.Fifteen out of 932 studies met our inclusion criteria and are presented in the current review.Results:The UroTrainer(Karl Storz GmbH,Tuttlingen,Germany),a virtual reality training simulator,achieved positive feedback and an excellent face and construct validity by the participants.The inspection of bladder mucosa,blood loss,tumor resection,and procedural time was improved after the training,especially for inexperienced urologists and medical students.The construct validity of UroSim®(VirtaMed,Zurich,Switzerland)was established.SIMBLA simulator(Samed GmbH,Dresden,Germany)was found to be a realistic and useful tool by experts and urologists with intermediate experience.The test objective competency model based on SIMBLA simulator could be used for evaluating urologists.The porcine model of the Asian Urological Surgery Training and Education Group also received positive feedback by the participants that tried it.The Simulation and Technology Enhanced Learning Initiative Project had an extraordinary face and content validity,and 60%of participants would like to use the simulators in the future.The 5-day multimodal training curriculum“Boot Camp”in the United Kingdom achieved an increase of the level of confidence of the participants that lasted months after the project.Conclusion:Simulators and courses or curricula based on a simulator training could be a valuable learning tool for any surgeon,and there is no doubt that they should be a part of every urologist's technical education.

Blast waveform tailoring using controlled venting in blast simulators and shock tubes

A critical challenge of any blast simulation facility is in producing the widest possible pressure-impulse range for matching against equivalent high-explosive events.Shock tubes and blast simulators are often constrained with the lack of effective ways to control blast wave profiles and as a result have a limited performance range.Some wave shaping techniques employed in some facilities are reviewed but often necessitate extensive geometric modifications,inadvertently cause flow anomalies,and/or are only applicable under very specific configurations.This paper investigates controlled venting as an expedient way for waveforms to be tuned without requiring extensive modifications to the driver or existing geometry and could be widely applied by existing and future blast simulation and shock tube facilities.The use of controlled venting is demonstrated experimentally using the Advanced Blast Simulator(shock tube)at the Australian National Facility of Physical Blast Simulation and via numerical flow simulations with Computational Fluid Dynamics.Controlled venting is determined as an effective method for mitigating the impact of re-reflected waves within the blast simulator.This control method also allows for the adjustment of parameters such as tuning the peak overpressure,the positive phase duration,and modifying the magnitude of the negative phase and the secondary shock of the blast waves.This paper is concluded with an illustration of the potential expanded performance range of the Australian blast simulation facility when controlled venting for blast waveform tailoring as presented in this paper is applied.

基于Power World Simulator的地区电网静态安全稳定性分析

电力系统具有良好的稳定性是保证电网正常运行的关键,充分应用Power World Simulator电力系统仿真软件对我国西北某地区实际电网进行安全稳定性分析。根据给定的实际电网运行数据搭建电网模型并进行潮流计算,将潮流计算结果与静态安全理论相结合,对该地区电网模型进行N-1静态安全性分析。针对线路负载率过高以及节点母线电压越限的情况,提出解决措施以达到提高电网运行稳定性的目的。

UltraStar:A Lightweight Simulator of Ultra-Dense LEO Satellite Constellation Networking for 6G

The mega-constellation network has gained significant attention recently due to its great potential in providing ubiquitous and high-capacity connectivity in sixth-generation(6G)wireless communication systems.However,the high dynamics of network topology and large scale of mega-constellation pose new challenges to the constellation simulation and performance evaluation.In this paper,we introduce UltraStar,a lightweight network simulator,which aims to facilitate the complicated simulation for the emerging mega-constellation of unprecedented scale.Particularly,a systematic and extensible architecture is proposed,where the joint requirement for network simulation,quantitative evaluation,data statistics and visualization is fully considered.For characterizing the network,we make lightweight abstractions of physical entities and models,which contain basic representatives of networking nodes,structures and protocol stacks.Then,to consider the high dynamics of Walker constellations,we give a two-stage topology maintenance method for constellation initialization and orbit prediction.Further,based on the discrete event simulation(DES)theory,a new set of discrete events is specifically designed for basic network processes,so as to maintain network state changes over time.Finally,taking the first-generation Starlink of 11927 low earth orbit(LEO)satellites as an example,we use UltraStar to fully evaluate its network performance for different deployment stages,such as characteristics of constellation topology,performance of end-to-end service and effects of network-wide traffic interaction.The simulation results not only demonstrate its superior performance,but also verify the effectiveness of UltraStar.

基于Plant Simulation的化纤自动落丝系统仿真实验分析

基于Plant Simulation软件,构建一种化纤自动落丝系统的3D数字化模型,对系统效率关键输入因子进行参数化设置,将系统各工位三维数字模型导入软件中建立层次化运动机构图形结构,并运用Simltalk语言实现三维动作仿真,通过基础物理参数设置,保证了仿真数字化模型与现实系统更具一致性。通过多级实验设计分析了系统影响因子对于系统效率的影响特性曲线,并进一步通过动态参数化实验方法,计算出双输入因子对系统效能影响的敏感度。该实验结果可为化纤自动落丝系统的建设成本控制与可行性分析提供指导,具有较好的工程应用价值。

基于Simulation X的多轴转向系统功能安全仿真分析

基于ISO 26262《道路车辆功能安全》的标准要求,对特种车的多轴电液转向系统进行分析,以提高系统的安全性和可靠性。运用Simulation X软件建立详细的多轴特种车仿真模型,通过模拟故障模式注入进行仿真试验。对仿真结果和数据进行分析,评估得到故障的严重性、暴露度和可控性,从而确定相应的汽车安全完整性等级。基于故障注入仿真的汽车功能安全分析方法,在系统早期设计阶段可以作为评估架构安全性的重要手段。

基于Plant Simulation的压气机叶片型线加工产线分析与优化

运用专业仿真软件Plant Simulation,根据压气机叶片型线机械加工工艺特点和物料运行流程建立生产线仿真模型,从产能、设备利用率及产线瓶颈等多方面进行仿真分析与优化。结果表明:Plant Simulation仿真平台的仿真可以找出规划设计方案中存在的问题并验证方案的合理性。该仿真结果为型线机械加工产线的优化设计提供了可靠依据,达到了节约投资成本和缩短设计周期的目的。

基于CarSim/Simulink的计算机控制系统综合实验设计

针对计算机控制系统课程中控制算法设计与仿真实现,设计了基于CarSim/Simulink的控制综合实验方案。以4轮独立驱动小车为对象,要求学生熟悉其基本工作原理,并在非线性动力学模型基础上,进行局部线性近似,设计反馈控制器,模拟小车控制。使用CarSim仿真软件可直观地模拟调整4轮独立驱动小车的质量、质心位置和转动惯量等,实现个性化选择,搭建车辆模型;与Simulink接口互通,在Simulink中完成控制算法。实验设计旨在使学生夯实计算机控制系统的理论基础,并逐步过渡到控制工程,理论联系实际,培养其解决复杂工程问题的能力。

基于Simulink的2PSK调制与解调系统的仿真分析

分析2PSK调制和解调的原理,采用Matlab环境下的Simulink仿真工具箱实现2PSK调制及解调系统的仿真建模与分析。仿真实验表明,仿真结果和理论分析内容一致,验证了仿真模型的正确性。该方法有助于相关研究者直观地理解相移调制与解调系统的组成及工作原理,对实际工程应用也有一定的借鉴作用。

3D FEM simulation of responses of LWD multi-mode resistivity imaging sonde

A new multi-mode resistivity imaging sonde, with toroidal coils as source, can conduct three resistivity measurements: azimuthal resistivity, lateral resistivity, and bit resistivity measurements. Thus, the logging time and cost are greatly saved. The toroidal coils are simplified as an extended voltage dipole and the response equations are derived for a homogenous formation. Based on 3D FEM, the depth of investigation(DOI), vertical resolution, circumferential azimuthal capacity, borehole diameter, mud resistivity, thickness of target formation, and the resistivity of the surrounding formation and mud invasion are simulated. The results suggest that the three measurement modes of the new sonde are different in vertical resolutions and DOIs. The circumferential detection ability of the azimuth button depends on the contrast between the anomaly and formation resistivity and the open angle of the anomaly. Whether the borehole is truncated at the bit or not has a great influence on the simulation results. The borehole and mud invasion affect the apparent resistivity in all modes, but the effects of resistivity of surrounding formation and thickness of the target formation are only corrected for lateral resistivity measurement.

Ensemble Simulation of Land Evapotranspiration in China Based on a Multi-Forcing and Multi-Model Approach

In order to reduce the uncertainty of offline land surface model （LSM） simulations of land evapotranspiration （ET）, we used ensemble simulations based on three meteorological forcing datasets [Princeton, ITPCAS （Institute of Tibetan Plateau Research, Chinese Academy of Sciences）, Qian] and four LSMs （BATS, VIC, CLM3.0 and CLM3.5）, to explore the trends and spatiotemporal characteristics of ET, as well as the spatiotemporal pattern of ET in response to climate factors over China's Mainland during 1982-2007. The results showed that various simulations of each member and their arithmetic mean （EnsAVlean） could capture the spatial distribution and seasonal pattern of ET sufficiently well, where they exhibited more significant spatial and seasonal variation in the ET compared with observation-based ET estimates （Obs_MTE）. For the mean annual ET, we found that the BATS forced by Princeton forcing overestimated the annual mean ET compared with Obs_MTE for most of the basins in China, whereas the VIC forced by Princeton forcing showed underestimations. By contrast, the Ens_Mean was closer to Obs_MTE, although the results were underestimated over Southeast China. Furthermore, both the Obs_MTE and Ens_Mean exhibited a significant increasing trend during 1982-98; whereas after 1998, when the last big EI Nifio event occurred, the Ens_Mean tended to decrease significantly between 1999 and 2007, although the change was not significant for Obs_MTE. Changes in air temperature and shortwave radiation played key roles in the long-term variation in ET over the humid area of China, but precipitation mainly controlled the long-term variation in ET in arid and semi-arid areas of China.

Exhaustive review of acceleration strategies for Monte Carlo simulations in photon transit

Monte Carlo simulation techniques have become the quintessence and a pivotal nexus of inquiry in the realm of simulating photon movement within biological fabrics.Through the stochastic sampling of tissue archetypes delineated by explicit optical characteristics,Monte Carlo simulations possess the theoretical capacity to render unparalleled accuracy in the depiction of exceedingly intricate phenomena.Nonetheless,the quintessential challenge associated with Monte Carlo simulation methodologies resides in their extended computational duration,which significantly impedes the re¯nement of their precision.Consequently,this discourse is speci¯cally dedicated to exploring innovations in strategies and technologies aimed at expediting Monte Carlo simulations.It delves into the foundational concepts of various acceleration tactics,evaluates these strategies concerning their speed,accuracy,and practicality,and amalgamates a comprehensive overview and critique of acceleration methodologies for Monte Carlo simulations.Ultimately,the discourse envisages prospective trajectories for the employment of Monte Carlo techniques within the domain of tissue optics.

A Multi-mode Electronic Load Sensing Control Scheme with Power Limitation and Pressure Cut-off for Mobile Machinery

In mobile machinery,hydro-mechanical pumps are increasingly replaced by electronically controlled pumps to improve the automation level,but diversified control functions(e.g.,power limitation and pressure cut-off)are integrated into the electronic controller only from the pump level,leading to the potential instability of the overall system.To solve this problem,a multi-mode electrohydraulic load sensing(MELS)control scheme is proposed especially considering the switching stability from the system level,which includes four working modes of flow control,load sensing,power limitation,and pressure control.Depending on the actual working requirements,the switching rules for the different modes and the switching direction(i.e.,the modes can be switched bilaterally or unilaterally)are defined.The priority of different modes is also defined,from high to low:pressure control,power limitation,load sensing,and flow control.When multiple switching rules are satisfied at the same time,the system switches to the control mode with the highest priority.In addition,the switching stability between flow control and pressure control modes is analyzed,and the controller parameters that guarantee the switching stability are obtained.A comparative study is carried out based on a test rig with a 2-ton hydraulic excavator.The results show that the MELS controller can achieve the control functions of proper flow supplement,power limitation,and pressure cut-off,which has good stability performance when switching between different control modes.This research proposes the MELS control method that realizes the stability of multi-mode switching of the hydraulic system of mobile machinery under different working conditions.

Global hybrid simulations of soft X-ray emissions in the Earth’s magnetosheath

Earth’s magnetopause is a thin boundary separating the shocked solar wind plasma from the magnetospheric plasmas,and it is also the boundary of the solar wind energy transport to the magnetosphere.Soft X-ray imaging allows investigation of the large-scale magnetopause by providing a two-dimensional(2-D)global view from a satellite.By performing 3-D global hybrid-particle-in-cell(hybrid-PIC)simulations,we obtain soft X-ray images of Earth’s magnetopause under different solar wind conditions,such as different plasma densities and directions of the southward interplanetary magnetic field.In all cases,magnetic reconnection occurs at low latitude magnetopause.The soft X-ray images observed by a hypothetical satellite are shown,with all of the following identified:the boundary of the magnetopause,the cusps,and the magnetosheath.Local X-ray emissivity in the magnetosheath is characterized by large amplitude fluctuations(up to 160%);however,the maximum line-of-sight-integrated X-ray intensity matches the tangent directions of the magnetopause well,indicating that these fluctuations have limited impact on identifying the magnetopause boundary in the X-ray images.Moreover,the magnetopause boundary can be identified using multiple viewing geometries.We also find that solar wind conditions have little effect on the magnetopause identification.The Solar wind Magnetosphere Ionosphere Link Explorer(SMILE)mission will provide X-ray images of the magnetopause for the first time,and our global hybrid-PIC simulation results can help better understand the 2-D X-ray images of the magnetopause from a 3-D perspective,with particle kinetic effects considered.

Importance of Photo-Realistic and Dedicated Simulator in Agricultural Robotics

Agricultural robotics is a comparatively new field. Recently, it has gotten special attention because of agricultural labor shortages and rising labor costs. With the increasing operational use of agricultural robots, the need for a dedicated robotic simulator for such activity has been noted here. The need of a dedicated and specialty simulator for agricultural robotics research is the main focus area of this paper. Moreover, limitations have been pointed out when conventional robot simulators are used directly in agricultural settings. In a nutshell, it has been tried to emphasize that a dedicated simulator for agricultural robotics would be a timely advance and would accelerate the growth of agricultural robots.

The Probability Density Function Related to Shallow Cumulus Entrainment Rate and Its Influencing Factors in a Large-Eddy Simulation

The process of entrainment-mixing between cumulus clouds and the ambient air is important for the development of cumulus clouds.Accurately obtaining the entrainment rate(λ)is particularly important for its parameterization within the overall cumulus parameterization scheme.In this study,an improved bulk-plume method is proposed by solving the equations of two conserved variables simultaneously to calculateλof cumulus clouds in a large-eddy simulation.The results demonstrate that the improved bulk-plume method is more reliable than the traditional bulk-plume method,becauseλ,as calculated from the improved method,falls within the range ofλvalues obtained from the traditional method using different conserved variables.The probability density functions ofλfor all data,different times,and different heights can be well-fitted by a log-normal distribution,which supports the assumed stochastic entrainment process in previous studies.Further analysis demonstrate that the relationship betweenλand the vertical velocity is better than other thermodynamic/dynamical properties;thus,the vertical velocity is recommended as the primary influencing factor for the parameterization ofλin the future.The results of this study enhance the theoretical understanding ofλand its influencing factors and shed new light on the development ofλparameterization.