Design of weak current measurement system and research on temperature impact

A dedicated weak current measurement system was designed to measure the weak currents generated by the neutron ionization chamber.This system incorporates a second-order low-pass filter circuit and the Kalman filtering algorithm to effectively filter out noise and minimize interference in the measurement results.Testing conducted under normal temperature conditions has demonstrated the system's high precision performance.However,it was observed that temperature variations can affect the measurement performance.Data were collected across temperatures ranging from -20 to 70℃,and a temperature correction model was established through linear regression fitting to address this issue.The feasibility of the temperature correction model was confirmed at temperatures of -5 and 40℃,where relative errors remained below 0.1% after applying the temperature correction.The research indicates that the designed measurement system exhibits excellent temperature adaptability and high precision,making it particularly suitable for measuring weak currents.

Absolute Wall Thickness Measurement of Conducting Plates Using Pulsed Eddy Currents

The method using pulsed eddy currents to determine the thickness of a conduction plate is extended to enable the simultaneous measurement of the plate thickness and material properties. For optimal performance, a probe must be designed depending on the thickness range that should be accessible. The need for a calibration of the material properties of a conducting plate to enable the measurement of its thickness has been removed. All that is needed is a probe with known dimensions and suitable hardware to create a current pulse and measure a transient magnetic induction.

Precision measurement and suppression of low-frequency noise in a current source with double-resonance alignment magnetometers

Low-noise high-stability current sources have essential applications such as neutron electric dipole moment measurement and high-stability magnetometers. Previous studies mainly focused on frequency noise above 0.1 Hz while less on the low-frequency noise/drift. We use double resonance alignment magnetometers(DRAMs) to measure and suppress the low-frequency noise of a homemade current source(CS) board. The CS board noise level is suppressed by about 10 times in the range of 0.001-0.1 Hz and is reduced to 100 n A/√Hz at 0.001 Hz. The relative stability of CS board can reach2.2 × 10^(-8). In addition, the DRAM shows a better resolution and accuracy than a commercial 7.5-digit multimeter when measuring our homemade CS board. Further, by combining the DRAM with a double resonance orientation magnetometer,we may realize a low-noise CS in the 0.001-1000 Hz range.

Algorithms for automatic measurement of SIS-type hysteretic underdamped Josephson junction’s parameters by current-voltage characteristics

Some electrical parameters of the SIS-type hysteretic underdamped Josephson junction(JJ)can be measured by its current-voltage characteristics(IVCs).Currents and voltages at JJ are commensurate with the intrinsic noise level of measuring instruments.This leads to the need for multiple measurements with subsequent statistical processing.In this paper,the digital algorithms are proposed for the automatic measurement of the JJ parameters by IVC.These algorithms make it possible to implement multiple measurements and check these JJ parameters in an automatic mode with the required accuracy.The complete sufficient statistics are used to minimize the root-mean-square error of parameter measurement.A sequence of current pulses with slow rising and falling edges is used to drive JJ,and synchronous current and voltage readings at JJ are used to realize measurement algorithms.The algorithm performance is estimated through computer simulations.The significant advantage of the proposed algorithms is the independence from current source noise and intrinsic noise of current and voltage meters,as well as the simple implementation in automatic digital measuring systems.The proposed algorithms can be used to control JJ parameters during mass production of superconducting integrated circuits,which will improve the production efficiency and product quality.

Speed Measurement Feasibility by Eddy Current Effect in the High-Speed MFL Testing

It is known that eddy current effect has a great influence on magnetic flux leakage testing(MFL).Usually,contacttype encoder wheels are used to measure MFL testing speed to evaluate the effect and further compensate testing signals.This speed measurement method is complicated,and inevitable abrasion and occasional slippage will reduce the measurement accuracy.In order to solve this problem,based on eddy current effect due to the relative movement,a speed measurement method is proposed,which is contactless and simple.In the high-speed MFL testing,eddy current induced in the specimen will cause an obvious modification to the applied field.This modified field,which is measured by Hall sensor,can be utilized to reflect the moving speed.Firstly,the measurement principle is illustrated based on Faraday’s law.Then,dynamic finite element simulations are conducted to investigate the modified magnetic field distribution.Finally,laboratory experiments are performed to validate the feasibility of the proposed method.The results show that Bmz(r1)and Bmx(r2)have a linear relation with moving speed,which could be used as an alternative measurement parameter.

Measurement of the current and spectral analysis on the continental shelf in the East China Sea

Direct measurements of current velocity and water temperature were undertaken at the mooring Sta. M (125°29.38' N, 31°49.70' E) on the continental shelf area in the East China Sea in June 1999 by R/V Xiangyanghong 14. The relationship between various time series of oceanic fluctuations is calculated by spectral analysis. The major results are as follows: (1) an average (u,v) of (6.9,-3.0 cm/s) at the 30 m depth is obtained during the 9-day observation, and that at the 45 m depth is (3.7,-1.1 cm/s), i. e., the mean flows are southeastward at both the 30 and 45 m depths;the currents become stronger gradually during the observation period; this may be mainly attributed to the transition of the tidal currents from neap to spring; (2)semidiurnal fluctuation is the most dominant in the current fluctuations, and rotates mainly clockwise; in the next place, there is also diurnal fluctuation;the local inertial period is close to the period of diurnal fluctuation, and an inertial motion is clockwise; thus, local inertial motion combines with diurnal fluctuation, and makes the spectral peaks in clockwise components much higher than those in counterclockwise ones; except for the fluctuations of above main periods, there is also the peak at 3 d period for counterclockwise compo-nents in the upper and lower layers; (3) the calculation of cross spectra between two time series of current velocities at the 30 and 45 m depths shows that both the current fluctuations at the 30 and 45 m depths are much alike, i. e., they are synchro; this shows that the flow field here is rather vertically homogeneous; (4)power spectra of tempera-ture time series at both the 30 and 45 m depths show that the semidiurnal peak is the most predominant, and the second highest peak is the diurnal period; besides spectral peaks at above periods, there are also obvious spectral peaks at 6.8 h and 2 d; (5)plots of temperature time series at 16 , 30 , 35 , 45 and 50 m depths show that the temporal variations of temperature at these depths are synchro, which are like those in the velocity field; temperature records also show a gradual rise in temperature, which are also like those in the velocity field.

Characteristics of Eddy Current Attenuation and Thickness Measurement of Metallic Plate

In eddy current testing, the law of attenuation of eddy current(EC) is of great concern. In conductive half space under the excitation of uniform magnetic field, the EC density decreases exponentially in the depth direction. However, in conductor with finite thickness tested by coil, the distribution of EC in the depth direction is more complicated. This paper studies the characteristics of EC attenuation in metallic plate of finite thickness. Simulation results show that there is an EC reflection at the bottom of plate, which changes the law of EC attenuation. A new concept, namely the equivalent attenuation coefficient, is proposed to quantify the speed of EC attenuation. The characteristics of EC attenuation are utilized to explain the nonmonotonic relation between coil voltage and plate thickness. Procedure of selecting frequency is discussed. Thereafter, measurement of plate thickness is carried out and accurate result is obtained.

Simulation of Current Measurement Using Magnetic Sensor Arrays and Its Error Model

Magnetic sensor arrays are proposed to measure electric current in a non-contact way. In order to achieve higher accuracy, signal processing techniques for magnetic sensor arrays are utilized. Simulation techniques are necessary to study the factors influencing the accuracy of current measurement. This paper presents a simulation method to estimate the impact of sensing area and position of sensors on the accuracy of current measurement. Several error models are built up to support computer-aided design of magnetic sensor arrays.

Design of a Rogowski Coil with a Magnetic Core Used for Measurements of Nanosecond Current Pulses

A Rogowski coil is developed to detect the nanosecond pulse signals of the discharge current with a wide bandwidth of 800 kHz to 106 MHz and high sensitivity of 2.22 V/A. Performance tests show that the Rogowski coil has both excellent dynamic and static characteristics. Calibrating results and the comparison between the standard current shunt and the developed Rogowski coil for the measurement of nanosecond discharge pulses demonstrate that the developed Rogowski coil can reproduce the actual waveform of the discharge current accurately.

Measurement of Current Profile in a Tokamak Through AC Modulation

The plasma current is modulated with an alternating current （ac） component in a frequency range of 90 Hz - 900 Hz in the plateau discharge phase in the CT-6B tokamak. A plasma electric conductivity profile in a form of （1 - r^2/a^2）^α with a parameter α which is fitted with the experimental data, can be determined. The effects of magnetic shear in a tokamak field configuration on the current penetration are taken into account in the numerical simulation. The measurement method and obtained results are discussed.

Measurement and Simulation of Induced Voltage and Current on 110 KV Crossing Transmission Lines under UHV AC Transmission Lines

The induced electricity of 110 kV transmission lines which cross the UHV AC transmission lines may threaten personal safety of the maintenance staff. In this paper, field measurement of the induced voltage and induced current on a 110 kV crossing line inside Jinhua in Zhejiang province is performed. The electrostatic induced voltage on the measured line is 12.24 kV. The power frequency electromagnetic field simulation model is established, and the calculation results are consistent with the measured. Influence factors analysis shows that the electrostatic induced voltage on the 110 kV line is 12.78 kV, the electromagnetic induced voltage is 12.3 V, the induced current through ground wire is less than 1A when the UHV lines operate at full load. The induced voltage and current decrease while the crossing distance increases. Parallel lines induction is much higher than crossing lines. The electromagnetic induced voltage after ground knife-switch shut down would exceed the human safety voltage 36 V while the crossing angle is less than 30?, so the temporary ground wire must be hanged to ensure safety of the maintenance staff.

Inversion of thicknesses of multi-layered structures from eddy current testing measurements

Luquire et al. ' s impedance change model of a rectangular cross section probe coil above a structure with an arbitrary number of parallel layers was used to study the principle of measuring thicknesses of multi-layered structures in terms of eddy current testing voltage measurements. An experimental system for multi-layered thickness measurement was developed and several fitting models to formulate the relationships between detected impedance/voltage measurements and thickness are put forward using least square method. The determination of multi-layered thicknesses was investigated after inversing the voltage outputs of the detecting system. The best fitting and inversion models are presented.

4-10 A 128-channel Picoammeter System and Its Application on Charged Particle Beam Current Distribution Measurements

The absolute current distribution is usually the most desirable parameter in experiments involving a charged particle beam. The Faraday cup array technique, a direct measurement of the absolute current distribution, has been developed both in one dimension[1] and two dimensions[2], providing a great advantage in terms of convenience. In this technique, a many-channel picoammeter (up to 128 channels) is necessary.

Quantitative assessment of sensory functions after 3 surgical approaches for trigeminal neuralgia by current perception threshold measurement

Objective: To quantitatively identify and grade trigeminal sensory functions after 3 major surgical procedures of trigeminal neuralgia using a newly developed quantitative sensory testing technique, current perception threshold measurement (CPTM). Methods: In the current study, there were 48 trigeminal neuralgia patients without history of prior surgical treatment. These patients received one of the following 3 surgical procedures, microvascular decompression (MVD), peripheral nerve block with alcohol (PNB), or percutaneous radiofrequency thermocoagulation (PRFT). The quantitative sensory testing measurement, CPTM, and conventional qualitative sensory testing measurements were performed preoperatively and postoperatively to evaluate and grade the trigeminal sensory functions. All 3 major cutaneous sensory fiber types, large myelinated fibers (A beta), small myelinated fibers (A delta) and unmyelinated fibers(C) were allowed to quantitatively evaluate and grade by CPTM. The results of the measurements were statistically analyzed using a one-way analysis of variance (single factor). Each subject was his/her own control for comparison of the preoperative to postoperative state on the asymptomatic and symptomatic sides. Subjects were tested 48 h preoperatively and 4 weeks postoperatively. Results: PNB with alcohol and PRFT caused significant sensory dysfunction postoperatively in every fiber type, indicating damage to all fibers. On the contrary, the sensory function in all 3 fiber types was unchanged after MVD management. Conclusion: Among the 3 major surgical procedures tested, only MVD preserves sensory function in trigeminal system. CPTM is of quantitative nature on the evaluation of sensory functions of nerve

Characteristics and Temperature Measurement of a Non-Transferred Cascaded DC Plasma Torch

Dependence of the current-voltage characteristics of a non-transferred DC cascaded plasma torch used for nanoparticle synthesis, on the plasma current and the plasma argon gas flow rate are reported in this paper. The potential structure inside the torch and its dependence on the plasma current and gas flow rate are also investigated. The arc voltage is seen to exhibit negative characteristic for a current below 150 A and positive characteristic above that current value. The voltage drop near the electrodes is found to decrease with the increase in plasma current. 25~ of the total voltage is dropped near the cathode at a plasma current of 50 A and a argon plasma gas flow rate of 10 liter per minute （LPM）, and it decreases to 12% with the current increasing to 300 A, and to 17% with a gas flow rate of 25 LPM. The variation in the torch efficiency with the gas flow rate and plasma current is also reported. The efficiency of the torch is found to be between 36% and 48%. In addition, the plasma gas temperature at various positions of the reactor and for different currents and voltages are measured by calorimetric estimation with a heat balance technique.

Current Situation and Comprehensive Control Measures of Water Environment in the Chaohu Lake

Based on the analysis of current situation of water environment in the Chaohu Lake,general ideas and measures of controlling the water environment were proposed. In respect of control ideas,controlling outbreaks of blue-green algae should be as one of control goals; it is needed to combine reducing the quantity of blue-green algae with decreasing eutrophication level to make the decrease in the quantity of blue-green algae larger than their natural increase until outbreaks of blue-green algae are eliminated; all kinds of techniques should be combined closely,integrated and innovated,and corresponding safeguard measures should be adopted. In respect of control measures,controlling sources of pollution and intercepting pollutants are basic measures,of which improving sewage treatment capacity and standard greatly is a key measure,and actively controlling pollution from large-scale livestock and poultry breeding is one of main measures; rivers polluted heavily should be controlled,and using microorganisms to purify small and moderate rivers can be as one of preferred techniques; blue-green algae should be dredged deeply to reducing their quantity; water should be transferred from the Yangtze River to the Chaohu Lake or the Hauihe River to purify water bodies and increase environmental capacity; reed wetland should be restored on a large scale to increase vegetation coverage from 5% to 20%; dredging should be combined with the elevation of basement of restored reed wetland.

Characterizing ship-induced hydrodynamics in a heavy shipping traffic waterway via intensified field measurements

Ship-induced hydrodynamics play an important role in shaping the cross-sectional profile of inland waterways and produce a large amount of pressure on the fluvial environment.This study aimed at quantifying the characteristics of ship-induced waves and currents in a heavy shipping traffic waterway via intensified field measurements conducted in the Changzhou segment of the Grand Canal,in Jiangsu Province,China.Based on the processed hydrodynamic data,waves and currents caused by single ships and multiple ships were investigated.For single ships,the shipinduced wave heights estimated with empirical formulas were not consistent with the observations.Categorized by the loading conditions of barges,the drawdown height was characterized by the ratio of ship speed to its limit speed.The maximum non-dimensional ship-induced wave height was parameterized by a nonlinear combination of the depth Froude number and a blockage coefficient.For multiple ships,when ships closely followed each other or interlaced each other's paths,it was difficult to characterize the superposition of several ship wakes.The magnitudes of current velocities induced by single ships and multiple ships were respectively nine and six times as large as those of natural flow.This may result in more severe sediment(re)suspension than natural flows.©2020 Hohai University.Production and hosting by Elsevier B.V.This is an open access article under the CC BY-NC-ND license(http://creativecommons.org/licenses/by-nc-nd/4.0/).

Temperature Effects on the Electrical Performance of Large Area Multicrystalline Silicon Solar Cells Using the Current Shunt Measuring Technique

The temperature effects on the electrical performance of a large area multicrystalline silicon solar cell with back-contact technology have been studied in a desert area under ambient conditions using the current shunt measuring technique. Therefore, most of the problems encountered with traditional measuring techniques are avoided. The temperature dependency of the current shunt from 5oC up to 50oC has been investigated. Its temperature coefficient proves to be negligible which means that the temperature dependency of the solar cell is completely independent of the current shunt. The solar module installed in a tilted position at the optimum angle of the location, has been tested in two different seasons (winter and summer). The obtained solar cell short circuit current, open circuit voltage and output power are correlated with the measured incident radiation in both seasons and all results are discussed.

CURRENTS CARRIED BY THE SUBGRADIENT GRAPHS OF SEMI-CONVEX FUNCTIONS AND APPLICATIONS TO HESSIAN MEASURES

In this paper we study integer multiplicity rectifiable currents carried by the subgradient （subdifferential） graphs of semi-convex functions on an n-dimensional convex domain, and show a weak continuity theorem with respect to pointwise convergence for such currents. As an application, the structure theorem of the Lagrangian currents for semi-convex functions is given and the k-Hessian measures are calculated by a different method in terms of currents.