Comparison study on measurement of rail weld joint between inertial reference method and multi-point chord reference method

Purpose – Straightness measurement of rail weld joint is of essential importance to railway maintenance. Dueto the lack of efficient measurement equipment, there has been limited in-depth research on rail weld joint with a5-m wavelength range, leaving a significant knowledge gap in this field.Design/methodology/approach – In this study, the authors used the well-established inertial referencemethod (IR-method), and the state-of-the-art multi-point chord reference method (MCR-method). Two methodshave been applied in different types of rail straightness measurement trollies, respectively. These instrumentswere tested in a high-speed rail section within a certain region of China. The test results were ultimatelyvalidated through using traditional straightedge and feeler gauge methods as reference data to evaluate the railweld joint straightness within the 5-m wavelength range.Findings – The research reveals that IR-method and MCR-method produce reasonably similar measurementresults for wavelengths below 1 m. However, MCR-method outperforms IR-method in terms of accuracy forwavelengths exceeding 3 m. Furthermore, it was observed that IR-method, while operating at a slower speed,carries the risk of derailing and is incapable of detecting rail weld joints and low joints within the track.Originality/value – The research compare two methods’ measurement effects in a longer wavelength rangeand demonstrate the superiority of MCR-method.

Multi-point discharge model: study on corona discharge of double-ended needle in large space

Corona discharge, as a common means to obtain non-equilibrium plasma, can generally obtain high-concentration plasma by increasing discharge points to meet production needs. However,the existing numerical simulation models used to study multi-point corona discharge are all calculations of small-scale space models, which cannot obtain the distribution characteristics of plasma in large space. Based on our previous research, this paper proposes a hybrid model for studying the distribution of multi-point discharge plasma in large-scale spaces, which divides the computational domain and computes separately with the hydrodynamic model and the ion mobility model. The simulation results are verified by a needle–ball electrode device. Firstly, the electric field distribution and plasma distribution of the needle electrodes with single tip and double tips are compared and discussed. Secondly, the plasma distribution of the needle electrode with the double tip at different voltages is investigated. Both computational and experimental results indicate that the charged particle concentration and current of the needle electrode with double tips are both twice as high as those of the needle electrode with a single tip. This model can extend the computational area of the multi-point corona discharge finite element model to the sub-meter(25 cm) or meter level, which provides an effective means to study the plasma distribution generated by multiple discharge points in large-scale space.

Multi-Point Forming Technology for Sheet Metal

Multi-point forming (MPF) is an advanced manufacturing technology for three-dimensional sheet metal parts. In this paper, the MPF integrated system is described that can form a variety of part shapes without the need for solid dies, and given only geometry and material information about the desired part. The central component of this system is a pair of matrices of punches, and the desired discrete die surface is constructed by changing the positions of punches though the CAD and control system. The basic MPF process is introduced and the typical application examples show the applicability of the MPF technology. Wrinkle and dimple are the major forming defects in MPF process, numerical simulation is a feasible way to predict forming defects in MPF. In conventional stamping, the mode to form sheet metal with blankholder is an effective way to suppress wrinkling; the same is true in MPF. A MPF press with flexible blankholder was developed, and the forming results indicated the forming stability of this technique. Based on the flexibility of MPF, varying deformation path MPF and sectional MPF were explored that cannot be realized in conventional stamping. By controlling each punch in real-time, a sheet part can be manufactured along a specific forming path. When the path of deformation in MPF is designed properly, forming defects will be avoided completely and lager deformation is achieved. A work piece can be formed section by section though the sectional MPF, and this technique makes it possible to manufacture large size parts in a small MPF press. Some critical experiments were performed that confirmed the validity of two special MPF techniques.

Simulation on damage effectiveness of hexagonal prism aimable warhead with multi-point synchronous initiations

In order to study the impacts of warhead geometry and initiation pattern on the lethality of aimable warhead, multi-point synchronous initiated hexagonal prism and cylindrical warheads were compared through numerical simulation, combined with theoretical formulas of fragment decelera- tion and target plugging. Enhancements of fragment velocity, kinetic energy and density toward the target and target destructions were analyzed. The results show that hexagonal prism warhead can produce dense fragment beams and enhance average velocity and kinetic energy with asymmetric eight-point initiation by 24. 13% and 54. 52% respectively, which are higher than those of the isomet- ric or same weight cylindrical warhead. The effective fragments are still relatively concentrated in an area of 8 m × 2 m for the hexagonal prism warhead when the distance between warhead and target is 40 m.

Existence Results of Third Order Multi-Point Boundary Value Problem at Resonance

A kind of third order multi-point boundary value problems, x＇＇＇（ ι） = f（ t, x （ t ）, x＂ （ t ）, x＇＇＇ （ t ） ） ＋ m 2 e（t）,t∈（0, 1）,x（0）=ax（ξ）,x＇（0）-0,x（l）= ^m2∑j=1 βjx（ηj）, fεC[0, 1]×R^3, e（t）∈L^1[0, 1],a≥0, is considered, all theβj＇s have not the same sign, 0〈ξ〈 l, 0〈η1〈 η2〈… 〈ηm.2〈 1. By using the coincidence degree theory, some existence theorems for the problems at resonance are obtained.

SOLUTIONS TO A SECOND-ORDER MULTI-POINT BOUNDARY VALUE PROBLEM AT RESONANCE

This article deals with the following second-order multi-point boundary value problem x″（t）=r（t,x（t）,x′（t））＋e（t）,t∈（0,1）x′（0）=m∑i=1aix′（ξi）,x（1）=n∑j=1βjx（ηj）, Under the resonance conditions m∑i=1ai=1,n∑j=1βj=1,n∑j=1βjηj=1 , by applying the coincidence degree theory, some existence results of the problem are established. The emphasis here is that the dimension of the linear operator is two. In this paper, we extend and improve some previously known results like the ones in the references.

Numerical simulation on the process of multi-point forming for tube

To apply the multi-point forming technology to the field of tube processing,the process of multi-point forming for tube is studied.Numerical simulation for the process of multi-point forming for tube is achieved by using elastic-plastic FEM in ABAQUS.During simulation,reasonable coefficient of mass scaling and friction model of penalty function are used.The influence of several major technological parameters on the process is analyzed.When the tube diameter is 60 mm and the forming curvature radius is 1000 mm,the distortion rate of cross-section and the absolute forming error gradually decrease with the increasing of tube wall thickness;However,when the tube wall thickness is constant,the smaller the curvature radius,the larger the distortion rate of cross-section,but as to forming part,its absolute forming error becomes smaller.

Multi-point Contact of the High-speed Vehicle-turnout System Dynamics

The wheel-rail contact problems, such as the number, location and the track of contact patches, are very important for optimizing the spatial structure of the rails and lowering the vehicle-turnout system dynamics. However, the above problems are not well solved currently because of having the difficulties in how to determine the multi-contact, to preciously present the changeable profiles of the rails and to establish an accurate spatial turnout system dynamics model. Based on a high-speed vehicle-turnout coupled model in which the track is modeled as flexible with rails and sleepers represented by beams, the line tracing extreme point method is introduced to investigate the wheel-rail multiple contact conditions and the key sections of the blade rail, longer nose rail, shorter rail in the switch and nose rail area are discretized to represent the varying profiles of rails in the turnout. The dynamic interaction between the vehicle and turnout is simulated for cases of the vehicle divergently passing the turnout and the multi-point contact is obtained. The tracks of the contact patches on the top of the rails are presented and the wheel-rail impact forces are offered in comparison with the contact patches transference on the rails. The numerical simulation results indicate that the length of two-point contact occurrence of a worn wheel profile and rails is longer than that of the new wheel profile and rails; The two-point contact definitely occurs in the switch and crossing area. Generally, three-point contact doesn’t occur for the new rail profile, which is testified by the wheel-rails interpolation distance and the first order derivative function of the tracing line extreme points. The presented research is not only helpful to optimize the structure of the turnout, but also useful to lower the dynamics of the high speed vehicle-turnout system.

Solvability of Non-homogeneous Mixed Type Multi-point BVPs for Second Order Differential Equations with p-Laplacian

A class of multi-point boundary value problems are studied.Easily verified suffcient conditions to guarantee the existence of at least one solutions of above mentioned BVPs are established.The examples are presented to illustrate the main results.

Existence of Solutions to Multi-point BVP with p-Laplacian at Resonance

This paper is concerned with the existence of solutions for the following multipoint boundary value problem at resonance{(Φp (x'))' + f(t,x)=0,0 < t < 1,x' (0)=x'(ξ) x(1)=m-3 ∑i=1 βi x(η i),where βi∈ R,m-3 ∑i=1 β i=1,0 < η 1 < η 2 < ··· < ηm-3 < 1,m-3 ∑i=1 βiηi=1,0 < ξ < 1.An existence theorem is obtained by using the extension of Mawhin's continuation theorem.Since almost all the multi-point boundary value problem at resonance in previous papers are for the linear operator without p-Laplacian by the use of Mawhin's continuation theorem,our method is new.

Analysis on the Seismic Response of Soil Slopes Based on the Multi-point Input Method

In general, the seismic response analysis in earthquake engineering assumes that the vibration parameters of the target and the contact surface of the external media are identical,i. e., single point input. However, earthquake energy has an attenuation phenomenon in wave propagation,so a wide range of soil slopes and the external medium contact surface of different input points on motion are not identical. If we consider single point input only, it may not correspond with reality, so it is necessary to carry out research on multi-point input methods. Based on the 2-D slope model,single-point input and multi-point input are performed respectively to analyze and compare their similarities and differences in the perspectives of the characteristics of seismic response of soil layer and plastic zone distribution to provide a reference for the seismic design of slopes. The results show that in the perspective of soil seismic response analysis,the peak acceleration output and peak velocity output under multi-point input are greater than the peak values under single point input at the same monitoring point,the peak appearing time is also earlier than that of the single point input; in terms of the plastic zone distribution,the multi-point effect is manifested as the presence of more obvious tensile shear failures; in the perspective of safety coefficient,the safety coefficient under each multi-point input is smaller than that of single point input,a difference of about 7 % or so. In summary,multi-point input is more reasonable and practical than single point input,so multi-point input should be considered in seismic design.

Improving effect on forming quality and accuracy using a polyurethane board positioning/resetting the discrete steel pad in multi-point forming

To improve the quality of multi-point die forming, a new approach using discrete steel pads was proposed. The formability of three different multi-point die forming processes was analyzed through numerical simulation and experiments. Numerical simulation and experimental results showed that the use of discrete steel pads in the multi-point forming process can substantially improve the stress–strain state on the plate and suppress dimple, straight-edge, and wrinkle defects. This analysis verified that the use of discrete steel pads in a multi-point forming process can effectively improve the quality and accuracy with which sheet metal is formed.

Multi-point airfoil optimization for axial-flow fan

Airfoil is the element of fan blade design. It is strongly anticipated to design a fan of ave- raged high performance over a wide operation range. Multi-point optimization design of airfoil for axial flow fan was proposed over specific operation range. Weighted objective function of airfoil lift-drag ratio was constructed for several operation points around the designing one. Airfoil was defined by parametric B-spline curve of limited shape controlling points. Results show that normal standard airfoils have remained spaces to be optimized under specific operation conditions. Airfoil performance is sensitive to flow′s Reynolds number and cascade solidity. Predicting flow transition along airfoil profile is essential to search for optimized one. Optimized airfoil of wide operation range is possible to obtain with prescribed fitness function. Obtainments of multi-point optimization may be relatively lower at design point, but positive obtainments are achieved at off-design ones. Resulted airfoil is specially suitable for axial flow fans operating frequently at off-design point such as air condition coolers.

Multi-point Boundary Value Problems for Nonlinear Fourth-order Differential Equations with All Order Derivatives

By using fixed point theorem, multiple positive solutions for some fourth- order multi-point boundary value problems with nonlinearity depending on all order derivatives are obtained. The associated Green＇s functions are also given.

Three-dimensional spatial multi-point uniform light focusing through scattering media based on feedback wavefront shaping

We use feedback wavefront shaping technology to realize the multi-point uniform light focusing in three-dimensional(3D) space through scattering media only by loading the optimal mask once.General 3D spatial focusing needs to load the optimal mask multiple times to realize the spatial movement of the focal point and the uniformity of multi-point focusing cannot be guaranteed.First,we investigate the effects of speckle axial correlation and different axial distances on 3D spatial multi-point uniform focusing and propose possible solutions.Then we use our developed non-dominated sorting genetic algorithm suitable for 3D spatial focusing(S-NSGA) to verify the experiment of multi-point focusing in 3D space.This research is expected to have potential applications in the fields of optical manipulation and optogenetics.

A Compact Difference Scheme for Multi-point Boundary Value Problems of Heat Equations

In this paper,a compact difference scheme is established for the heat equations with multi-point boundary value conditions.The truncation error of the difference scheme is O(τ2+h^4),where t and h are the temporal step size and the spatial step size.A prior estimate of the difference solution in a weighted norm is obtained.The unique solvability,stability and convergence of the difference scheme are proved by the energy method.The theoretical statements for the solution of the difference scheme are supported by numerical examples.

Full-length model with multi-point settings for finishing rolling

Thickness,width,temperature,and profile are considered as control targets in process control of hot strip finishing rolling. The pre-calculated settings of the model information include rolling force,cooling water flow between stands,bending force,and roll shifting position. Without changing the load distribution,the interaction among thread speed,rolling force,rolling power,and cooling water flow between stands is comprehensively considered based on the quantifiable relationship among speed,force,and temperature. This paper proposes a full-length multi-point-setting model that uses the settings of strip head to combine the rolling speed diagram with the target finishing mill delivery temperature( FDT) to achieve the calculation of the control parameters along full length of strip. Traditional models cannot effectively predict rolling force of strip body or the maximum and minimum temperatures of FDT. It is also difficult for traditional models to suppress fluctuations in shape accuracy of full-length strip or improve the shape accuracy of the product. Calculation results show that the proposed full-length multi-point-setting model can provide the control parameters for temperature and rolling-force over full length of strip,predict the risk of rolling exceeding the equipment capability,and improve the shape accuracy and rolling stability of hot-rolled products.

12点调平系统及其应急预案措施

With high stability,strong bearing capacity and other characteristics,multi-point leveling systems have been widely used in various industries.The mobile platform here uses a 12-point leveling system,which is mainly composed of the mechanical transmission system of the supporting arm,a hydraulic drive system and an electrical control system.The leveling is realized through the proportional lifting of the arms in four quadrants.In order to ensure the smooth conduct of launch missions,emergency plans were made for the leveling system incase of failure of a single arm.

汇聚组播:新型MPLS服务质量组播体系结构

为支持新兴网络应用,IP组播(multicast)和MPLS(multi-protocol label switching)技术分别从不同方向扩展了当前的IP路由和交换模式.MPLS和IP组播的结合是当前研究的一个热点,MPLS网络中的服务质量组播面临着标签资源匮乏、组播路由状态的可扩展性以及具体实现上的困难.针对这些问题,提出了基于汇聚方法的新型MPLS服务质量组播体系结构,提出在现有的路由控制平面上叠加一层面向IP组播服务的控制平面,取代组播路由协议并支持组播聚集,形成2层控制平面结构.定义了两平面之间的协作和交互方式,并通过扩展RSVP-TE(resourcereservation protocol-traffic engineering)P2MP(point to multi-point)协议,在新的体系结构中融合了服务质量控制能力.另外,还探讨了汇聚组播中基于距离约束选择汇聚路由器的算法,实现了基于Linux的MPLS组播路由器和IP组播服务控制系统,并组建了实验平台.实验和模拟结果表明,基于汇聚组播的双平面网络控制结构能够适应组播用户和网络拓扑的动态变化,能够有效节省MPLS标签资源,平衡网络中组播流量的分布.

Dynamic Properties and Energy Conversion Efficiency of A Floating Multi-Body Wave Energy Converter

The present study proposed a floating multi-body wave energy converter composed of a floating central platform,multiple oscillating bodies and multiple actuating arms. The relative motions between the oscillating bodies and the floating central platform capture multi-point wave energy simultaneously. The converter was simplified as a forced vibration system with three degrees of freedom, namely two heave motions and one rotational motion. The expressions of the amplitude-frequency response and the wave energy capture width were deduced from the motion equations of the converter. Based on the built mathematical model, the effects of the PTO damping coefficient, the PTO elastic coefficient, the connection length between the oscillating body and central platform, and the total number of oscillating bodies on the performance of the wave energy converter were investigated. Numerical results indicate that the dynamical properties and the energy conversion efficiency are related not only to the incident wave circle frequency but also to the converter’s physical parameters and interior PTO coefficients. By adjusting the connection length, higher wave energy absorption efficiencies can be obtained. More oscillating bodies installed result in more stable floating central platform and higher wave energy conversion efficiency.